Citroen C4 DAG 2014.5 2.G Manual Online

79 
C4-2_en_Chap04_ouvertures_ed01-2014
Reinitialisation
After 
reconnecting
 
the
 
battery
 
or
 
a
 
fault,
 
you

 
must
 
be
 
reinitialise
 
the
 
operation
 
of
 
the

 
electric
 
windows.
 
For
 
each
 
of
 
the
 
control

 
switches
 
on
 
the
 
driver's
 
side
 
control

  panel:
F
 
pull
 
the
 
control
 
until
 
the
 
window
 
stops,
F

 
release
 
the
 
control
 
and
 
pull
 
it
 
again
 
until

  the   window   closes   fully,
F
 
continue
 
to
 
hold
 
the
 
control
 
for
 
ap
-
proximately
 
one
 
second
 
after
 
the
 
window

  has   closed,
F

press the control to lower the win
-
dow
 
automatically
 
to
 
the
 
low
 
posi
-
tion,
F
 
when
 
the
 
window
 
has
 
reached
 
the
 
low

 
position,
 
press
 
the
 
control
 
again
 
for

  approximately   one   second.
The safety anti-pinch function is not
operational during these operations. F
 
For
 
the
 
safety
 
of
 
your
 
children,
 
press
 
control 5

 
to
 
deactivate
 
the
 
rear
 
elec
-
tric
 
window
 
controls
 
regardless
 
of
 
their

  position.
Indicator
 
lamp
 
on,
 
the
 
rear
 
controls
 
are
 
deactivated.
Indicator

 
lamp
 
of
f,  
the
 
rear
 
controls
 
are
 
activated.
Deactivation of the rear electric
window controlsAlways remove the  key  from  the  ignition
 when  leaving  the  vehi -
cle,
  even   for   a   short   time.
If
 
an
 
obstacle
 
is
 
encountered
 
during

 
operation
 
of
 
the
 
electric
 
windows,

 
you
 
must
 
reverse
 
the
 
movement

 
of
 
the
 
window
.  
T
o  
do

 
this,
 
press
 
the
 
control
 
con
-
cerned.
When
 
the
 
driver
 
operates
 
the
 
controls

 
for
 
the
 
passengers'
 
electric

 
windows,
 
they
 
must
 
en
-
sure
 
that
 
nothing
 
is
 
preventing
 
the

  windows   closing   correctly.
The
 
driver
 
must
 
ensure
 
that
 
the
 
passengers

 
use
 
the
 
electric
 
win
-
dows
  correctly.
Be
 
aware
 
of
 
children
 
when
 
oper
-
ating
  the   windows.
4
ACCESS

80 
C4-2_en_Chap04_ouvertures_ed01-2014
PANORAMIC SUNROOF
Your vehicle is  fitted  with  a  tinted  glass  panoramic
 sunroof  which  increases  
the

 
light
 
and
 
visibility
 
in
 
the
 
passenger
 
compartment.

 
Its
 
electric
 
blind
 
helps
 
control

 
the
 
temperature
 
in
 
the
 
passen
-
ger
  compartment.
Electric blind
Opening
Turn  
the
 
dial
 
to
 
the
 
left
 
(four
 
possible
 
settings).
Closing
Return

  the   dial   to   the   initial   position.Safety anti-pinch
If
 
the
 
blind
 
encounters
 
an
 
obstacle
 
dur
-
ing  
closing,
 
it
 
stops
 
and
 
partially
 
opens
 
again.
If

 the  blind  fails  to  close  at  a  second  at -
tempt,  it  may  be  necessary  to  force  the  
closing

 
of
 
the
 
blind
 
using
 
the
 
reinitiali
-
sation
  procedure.
The
 
blind
 
is
 
controlled
 
electrically
 
by
 
a
 
rotary

  dial. In  
the
 
event
 
of
 
contact
 
during
 
op
-
eration  
of
 
the
 
blind,
 
you
 
must
 
re
-
verse  
its
 
movement.
 
T
o  
do
 
this,
 
turn

  the   dial.
When  the  driver  operates  the  dial,
 they  must  ensure  that  noth -
ing
 
prevents
 
the
 
blind
 
from
 
clos
-
ing
  correctly.
The
 
driver
 
must
 
ensure
 
that
 
the
 
passengers

 
use
 
the
 
blind
 
cor
-
rectly.
Be
 
aware
 
of
 
children
 
during
 
opera
-
tion
  of   the   blind.
Reinitialising the system
Following reconnection of  the  battery ,  or
 in  the  event  of  a  malfunction  in  its  
operation,

 
it
 
may
 
be
 
necessary
 
to
 
reini
-
tialise
  the   system:
F
 
turn
 
the
 
dial
 
to
 
the
 
fully
 
closed
 
posi
-
tion,
F
 
then
 
immediately
 
press
 
the
 
dial,
 
clos
-
ing
  starts   after   about   10   seconds,
F
 
maintain
 
pressure
 
on
 
the
 
dial
 
until
 
the

  blind   has   fully   closed.
The anti-pinch function is inopera-
tive during these operations.
If
 
the

 
position

 
of

 
the

 
blind

 
does

 
not

 
agree

 
with

 
the

 
position

 
indicated

 
by

 
the

 
dial,

 
press

 
the

 
dial

 
to

 
open

 
the

 
blind

 
to

 
this

 
position.
4
ACCESS

55
81 
C4-2_en_Chap05_visibilite_ed01-2014
LIGHTING CONTROLS
System for selection  and  control  of  the  various
 front  and  rear  lamps  providing  
the

  vehicle's   lighting.
Main lighting
The various front  and  rear  lamps  of  the vehicle
 are  designed  to  adapt  the  driver's visibility

 
progressively
 
according
 
to
 
the climatic

  conditions:
-
 
sidelamps,
  to   be   seen,
-
 
dipped
 
beam
 
headlamps
 
to
 
see
 
without

  dazzling   other   drivers,
-
 
main beam  headlamps  to  see  clearly when
  the   road   is   clear.
Additional lighting
Other lamps are  provided  to  meet  the  requirements
 of  particular  driving  con -
ditions:
-
 
rear
  foglamps,
-
 front

 
foglamps
 
with
 
cornering
 
lighting,
-

 
directional
 
headlamps
 
for
 
improved
 
visibility

  when   cornering,
-
 
daytime
 
running
 
lamps
 
to
 
be
 
more
 
visible

  during   the   day,
-
 guide-me-home

 
and
 
welcome
 
light
-
ing
 
to
 
facilitate
 
access
 
to
 
the
 
vehicle,
-

 
parking
 
lamps
 
as
 
vehicle
 
position
 
markers.
Programming
The setting of  some  functions  can  be  adjusted:
-
 
daytime
  running   lamps,
-
 automatic

 
illumination
 
of
 
headlamps,
-

 
guide-me-home
  lighting,
-
 
welcome
  lighting,
-
 
directional
  lighting.
In
 
some

 
weather

 
conditions

 
(e.g. low

 
temperature

 
or

 
humidity),

 
the presence

 
of

 
misting

 
on

 
the

 
inter

-
nal
 
surface

 
of

 
the

 
glass

 
of

 
the headlamps

 
and

 
rear

 
lamps

 
is

 
nor

-
mal;
 
it

 
disappears

 
after

 
the

 
lamps have

 
been
 
on
 
for
 
a
 
few
 
minutes.
VISIBILITY

55
82 
C4-2_en_Chap05_visibilite_ed01-2014
Model without AUTO lightingModel with AUTO lighting A.
 Main  lighting  mode  selection  ring:  turn
 it  to  position  the  symbol  re -
quired
  facing   the   mark.
Manual controls
The lighting is  controlled  directly  by  the  driver
 by  means  of  the  ring  A  and  the  
stalk

  B.
Lighting off / daytime running lamps.
Automatic illu mination  of  head -
lamps.
B.
 
Stalk
 
for
 
switching
 
headlamps:
 
pull
 
the

 
stalk
 
towards
 
you
 
to
 
switch
 
the
 
lighting

 
between
 
dipped
 
and
 
main
 
beam

  headlamps.
In
 
the

 
lamps
 
of
f  
and
 
sidelamps
 
modes,
 
the driver

 
can
 
switch
 
on
 
the
 
main
 
beam
 
head
-
lamps
 
temporarily
 
("headlamp
 
flash")
 
by maintaining

  a   pull   on   the   stalk.
Sidelamps.
Dipped
 
headlamps
 
or
 
main
 
beam

  headlamps.
Displays
Illumination of  the  corresponding  indica -
tor  lamp  in  the  instrument  panel  confirms that

  the   lighting   selected   is   on.
Daytime running lamps
Daytime lighting, compulsory  in  certain  countries,
 which  comes  on  automati -
cally
 
when
 
the
 
engine
 
is
 
started
 
making
 
the

  vehicle   more   visible   to   other   users.
This
  function   is   assured:
-
 
in
 
countries
 
where
 
it
 
is
 
imposed
 
by
 
regulations,
 by

 
illu
mination  
of
 
the
 
dipped
 
beam
 
headlamps

 
with
 
the
 
sidelamps
 
and
 
number

 
plate
 
lamps;
 
this
 
function
 
cannot

  be   deactivated.
-
 
for
 
other
 
countries
 
where
 
it
 
is
 
pro
-
vided,
 by

 
the
 
use
 
of
 
dedicated
 
lamps;
 
this
 
function

 
can
 
be
 
activated
 
or
 
deac
-
tivated
 
via
 
the
 
vehicle
 
configuration
 
menu.
The

 
instruments
 
and
 
controls
 
(instru
-
ment
 
panel,
 
multifunction
 
screen,
 
air
 
conditioning

 
control
 
panel,
  ...)  
are
 
not
 
illu

minated,  
except
 
in
 
night
 
mode
 
with
 
manual

 
or
 
automatic
 
illu
mination  
of
 
headlamps.
VISIBILITY

55
83 
C4-2_en_Chap05_visibilite_ed01-2014
C. Foglamp  selection   ring.
The  
foglamps
 
operate
 
with
 
the
 
dipped
 
and

  main   beam   headlamps.
They
 
operates
 
with
 
the
 
dipped
 
beam headlamps

  and   main   beam   headlamps.
F
 
T
o  
switch
 
on
 
the
 
rear
 
foglamps,
 
turn
 
the

  ring   C   forwards.
F
 
T
o  
switch
 
of
f  
the
 
rear
 
foglamps,
 
turn
 
the

  ring   C   rearwards.
When automatic  illumination  of  headlamps is
 on  (with  AUT O  model),  the  dipped  beam headlamps

 
and
 
sidelamps
 
remain
 
on
 
while the

  rear   foglamps   are   on.
Model with rear foglamps only rear   foglamps
Rotate
  and   release   the   ring   C:
F
 
forwards
 
a
 
first
 
time
 
to
 
switch
 
on
 
the
 
front

  foglamps,
F
 
forwards
 
a
 
second
 
time
 
to
 
switch
 
on
 
the

  rear   foglamps,
F
 
rearwards
 
a
 
first
 
time
 
to
 
switch
 
of
f  
the

  rear   foglamps,
F
 
rearwards
 
a
 
second
 
time
 
to
 
switch
 
of

  the   front   fog   lamps.
Model with front and
rear foglamps front
  and   rear   foglampsWhen
 
the
 
headlamps
 
switch
 
of
f  
with automatic

 
illumination
 
of
 
headlamps (AUT

O  
model)
 
or
 
when
 
the
 
dipped
 
beam headlamps

 
are
 
switched
 
of
f  
manually
,
 the

  foglamps   and   sidelamps   remain   on.
F
 
T
urn  
the
 
ring
 
rearwards
 
to
 
switch
 
of

f  
the
 
foglamps,
 
the
 
sidelamps
 
will
 
then

  switch   off.
In
 
good
 
or
 
rainy
 
weather
,  
by
 
both
 
day

 
and
 
night,
 
the
 
front
 
foglamps
 
and

 
the
 
rear
 
foglamps
 
are
 
pro
-
hibited.  
In
 
these
 
situations,
 
the
 power
 of  their  beams  may  dazzle  other
 drivers.  They  should  only  be
  used   in   fog   or   falling   snow.
In
 
these
 
weather
 
conditions,
 
you
 
should

 
switch
 
on
 
the
 
foglamps
 
and

 
dipped
 
beam
 
headlamps
 
manually

,  
as
 
the
 
sunshine
 
sen
-
sor
  may   detect   sufficient   light.
Do
 
not
 
forget
 
to
 
switch
 
of
f  
the
 
front

 
and
 
rear
 
foglamps
 
when
 
they

  are   no   longer   necessary.
VISIBILITY

55
84 
C4-2_en_Chap05_visibilite_ed01-2014
Parking lamps
Side markers for  the  vehicle  by  illu mi-
nation  of  the  sidelamps  on  the  traffic  
side

  only.
F
 
Within
 
one
 
minute
 
of
 
switching
 
of
f  
the

 
ignition,
 
operate
 
the
 
lighting
 
con
-
trol
 
stalk
 
up
 
or
 
down
 
depending
 
on
 
the

 
traffic
 
side
 
(for
 
example:
 
when
 
parking

 
on
 
the
 
left;
 
lighting
 
control
 
stalk

 
upwards;
 
the
 
right
 
hand
 
side
-
lamps
  are   on).
This
 
is
 
confirmed
 
by
 
an
 
audible
 
signal
 
and

 
illu
mination  
of
 
the
 
corresponding
 
direction

 
indicator
 
warning
 
lamp
 
in
 
the
 
instrument

  panel.
To
 
switch
 
of
f  
the
 
parking
 
lamps,
 
return
 
the

 
lighting
 
control
 
stalk
 
to
 
the
 
central
 
position.
Switching off the lighting when


switching off the ignition
When
 the
 ignition
 is
 switched
 of
f, all

 
of

 
the

 
lamps

 
switch

 
of

f
 
immedi

-
ately,
 
except

 
for

 
the

 
dipped

 
beam headlamps

 
if

 
automatic

 
guide-
me-home

 
lighting
 
is
 
activated.
Manual guide-me-home lighting
The temporary  illumination  of  the  dipped beam
 headlamps  after  the  vehicle's  ignition has

 
been
 
switched
 
of
f  
makes
 
the
 
driver's exit

  easier   when   the   light   is   poor.
Switching on
F 
With
 
the
 
ignition
 
of
f,  
"flash"
 
the
 
headlamps

  using   the   lighting   stalk.
F
 
A further
 
"headlamp
 
flash"
 
switches
 
the

  function   off.
Switching off
The
 
manual
 
guide-me-home
 
lighting switches

 
of
f  
automatically
 
after
 
a
 
set
 
time.
Switching on the lighting


when switching on the ignition
To reactivate  the  lighting  control stalk, turn the  ring  A to position "0"   -  lighting off, then  to  the  position  of your
  choice.
If
 
the
 
lighting
 
is
 
switched
 
on
 
manu
-
ally
 
after
 
switching
 
of
f  
the
 
ignition, there

 
is
 
an
 
audible
 
signal
 
when
 
a front

 
door
 
is
 
opened
 
to
 
warn
 
the driver

 
that
 
they
 
have
 
forgotten
 
to switch

 
of
f  
the
 
vehicle's
 
lighting,
 
with the

  ignition   off.
They
 
switch
 
of
f  
automatically
 
after
 
a period

 
which
 
depends
 
on
 
the
 
state of

 
charge
 
of
 
the
 
battery
 
(entry
 
to
 
en
-
ergy
  economy   mode).
VISIBILITY

55
85 
C4-2_en_Chap05_visibilite_ed01-2014
Automatic illumination of
headlamps
The sidelamps and  dipped  beam  head -
lamps  are  switched  on  automatically ,  
without any action on the part of the
driver

,  
when
 
a
 
low
 
level
 
of
 
external
 
light
 
is

 
detected
 
or
 
in
 
certain
 
cases
 
of
 
activa
-
tion
  of   the   windscreen   wipers.
As
 
soon
 
as
 
the
 
brightness
 
returns
 
to
 
a
 
sufficient

 
level
 
or
 
after
 
the
 
windscreen
 
wipers

 
are
 
switched
 
of
f,  
the
 
lamps
 
are
 
switched

  off   automatically.
Activation
F
 
T
urn  
ring
 
A to the

"AUTO"  
position. The

 
automatic
 
illumination
 
of
 
head
-
lamps
  is   accompanied   by  
a
 
message in

  the   screen.
Deactivation
F
 
T
urn  
ring
 
A
to a position other
than

"AUT
O".  
Deactivation
 
is
 
ac
-
companied
 
by
 
a
 
message
 
in
 
the
 
screen.Coupling with the automatic "Guide-
me-home" lighting
Association

 with  the  automatic  illu mi-
nation  of  headlamps  provides  "guide-
me-home"
 
lighting
 
with
 
the
 
following
 
additional

  options:
-
 
selection
 
of
 
the
 
lighting
 
duration
 
to
 
15,

 
30
 
or
 
60
 
seconds
 
in
 
the
 
settings
 
in

 
the
 
vehicle
 
configuration
 
menu
 
(except

 
in
 
the
 
case
 
of
 
the
 
mono
-
chrome
 
screen
 
A,
 
for
 
which
 
the
 

duration

  is   set:   60   seconds),
-
 automatic

 
activation
 
of
 
"guide-me-
home"

 
lighting
 
when
 
automatic
 
illumi
-
nation
  of   headlamps   is   in   operation.
In the event of a fault with the
sunshine sensor ,  the  lighting come

 
on,
 
this
 
warning
 
lamp
 
is displayed

 
on
 
the
 
instrument
 
panel
 
and/or
 
a message

 
appears
 
in
 
the
 
screen,
 
accompa
-
nied
 
by
 
an
 
audible   signal.
Contact
 
a

 
CITROËN
 
or
 
a
 
qualified
 
work
-
shop
 
workshop.
Operating fault
In  
fog
 
or
 
snow
,  
the
 
sunshine
 
sensor

 
may
 
detect
 
sufficient
 
light.

 
Therefore,
 
the
 
lighting
 
will
 
not

  come   on   automatically.
d

o not cover the sunshine sen-
sor,
 
coupled
 
with
 
the
 
rain
 
sensor
 
and

 
located
 
in
 
the
 
centre
 
of
 
the
 
windscreen

 
behind
 
the
 
rear
 
view
 
mirror;

 
the
 
associated
 
functions
 
would

  no   longer   be   controlled.
VISIBILITY

55
86 
C4-2_en_Chap05_visibilite_ed01-2014
Switching off
The 
welcome
 
lighting
 
switches
 
of
f  
au
-
tomatically
 
after
 
a
 
programmed
 
time,
 
when

 
the
 
ignition
 
is
 
switched
 
on
 
or
 
on
 
locking

  the   vehicle.
Welcome lighting
Switching onF  
Press
 
the
 
open
 
padlock
 
on
 
the

 
remote
 
control;
 
your
 
ve
-
hicle
  is   unlocked.
The
 
remote
 
switching
 
on
 
of
 
the
 
light
-
ing  
makes
 
your
 
access
 
to
 
the
 
vehicle
 
easier

 
in
 
poor
 
light.
 
It
 
is
 
activated
 
de
-
pending  
on
 
the
 
light
 
level
 
detected
 
by
 
the

  sunshine   sensor.
The  
sidelamps
 
and
 
dipped
 
beam
 
head
-
lamps,
 
as
 
well
 
as
 
the
 
side
 
spotlamps,
 
lo
-
cated
  under   the   door   mirrors,   come   on.Programming
Activation  
or
 
deactivation,
 
as
 
well

 
as
 
the
 
duration
 
of
 
the
 
light
-
ing  
duration
 
for
 
the
 
welcome
 
lighting

 
can
 
be
 
set
 
via
 
the
 
ve
-
hicle   configuration   menu.
VISIBILITY

55
87 
C4-2_en_Chap05_visibilite_ed01-2014
To avoid causing  a  nuisance  to  other  road
 users,  the  height  of  the  halogen  
headlamps

 
should
 
be
 
adjusted
 
accord
-
ing
  to   the   load   in   the   vehicle.
0.
 
1
  or   2   people   in   the   front   seats.
-.
 
3
  people.
1.
 
5
  people.
-.
 
Intermediate
  setting.
2.
 
5
 
people
 
+
 
maximum
 
authorised
 
load.
-.

 
Intermediate
  setting.
3.
 
Driver
  +   maximum   authorised   load.
MANUAL AD j USTMENT OF HALOGEN
HEADLAMPS
The initial setting is position "0".
AUTOMATIC ADjUSTMENT OF XENON
HEADLAMPS
This system  adjusts  the  height  of  the  xenon
 headlamp  beams  automatically  
and

 
when
 
stationary
,  
according
 
to
 
the
 
load

 
in
 
the
 
vehicle,
 
so
 
as
 
to
 
avoid
 
caus
-
ing
  a   nuisance   to   other   road   user.
If
 
a
 
malfunction
 
occurs,
 
this
 
warning

 
lamp
 
is
 
displayed
 
in

 
the
 
instrument
 
panel,
 
ac
-
companied
 
by
 
an
 
audible
 
signal
 
and
 
a
 
message

  in   the   screen.
The system then  places  your  headlamps in
  the   lowest   position.
Do not touch the xenon bulbs.
Contact  
a
 
CITROËN
 
dealer
 
or
 
a
 
qualified

  workshop.
VISIBILITY

55
88 
C4-2_en_Chap05_visibilite_ed01-2014
DIRECTIONAL LIGHTING
Programming
with directional lighting
without directional lighting
When
 
the

 
dipped

 
or

 
main

 
beam

 
head

-
lamps
 
are

 
on,

 
this

 
function,

 
allows

 
the

 
light

 
beams
 
to
 
better
 
follow
 
the
 
road.
The
 
use

 
of

 
this

 
function,

 
coupled

 
with

 
the

 
xenon

 
headlamps

 
and

 
the

 
corner

-
ing
 
lighting,

 
considerably

 
improves

 
the

 quality
 
of
 
your
 
lighting
 
round
 
bends.
Operating faultIf
 
a
 
fault
 
occurs,
 
this
 
warning
 
lamp

 
flashes
 
in
 
the
 
instrument
 
panel,

 
accompanied
 
by
 
a
 
mes
-
sage
  in   the   screen.
Contact
 
a
 
CITROËN
 
dealer
 
or
 
a
 
quali
-
fied
  workshop.
This
  function   is   inactive:
-  
when
  stationary   or   at   low   speeds,
-  
when
  reverse   is   engaged.
The  
system
 
is
 
activated
 
or
 
de
-
activated
 
in
 
the
 
vehicle
 
configu
-
ration
  menu.
 The

 
system
 
is
 
activated
 
by
 
de
-
fault.
The
 
state
 
of
 
the
 
system
 
stays
 
in
 
memory on

  switching   off   the   ignition.
VISIBILITY