light Citroen C4 PICASSO 2008 1.G Owner's Manual

IN BRIEF
I
4
E X T E R I O R
Panoramic glass roof
Xenon directional headlamps
Whether on dipped beams or main beams, this func-tion allows your headlamps to follow the direction of the road ahead.
Opening rear screen
Pneumatic rear suspension
The rear pneumatic suspen-sion enhances driving comfort and maintains a constant body height whatever the vehicle load.
Exterior side lighters
These light up the zones fac-ing the driver’s and passen-ger’s doors.
Front/rear parking assistance
Sensors located in the bumpers detect obstacles.
Parking space sensor
Measures the size of a space and informs you of the possi-bility of parking.
Exterior rear view mirrors
With electric foldback.
Automatically tilts in reverse gear.

A
B
C
D
B
A
IN BRIEF
I
5
O P E N I N G
Remote control key
A. Central locking
B. Unlocking
C. Guide-me-home lighting
D. Key release/storage
Fuel tank (60 litres)
Press on control A located on the control panel to the left of the dashboard. The fuel fl ap automati-cally opens up fully.
Insert the nozzle so as to push in the metallic gate valve B.
Push the fuel fl ap to reclose it.
After switching off the ignition, control A is only active for a few Aminutes. If necessary, switch on the ignition again to reactivate it.
Bonnet stay : detach the stay and pivot it upwards to insert it into the notch.
To close : move the stay back to its initial position, lower the bonnet until it is horizontal, then allow it to slam shut.
Bonnet opening/closing
To unlock, pull the control locat-ed under the dashboard towards you.
Opening
Using the multifunction screen, you can choose from the following options when opening your vehi-cle with the remote control :
- either all of the doors and the tailgate,
- or the driver’s door with a fi rst press, then all of the other doors with a second press.

B
A
C
D
IN BRIEF
I
10
I N T E R I O R
S e c o n d - r o w s e a t s
THE “COMFORT” POSITION
The 3 second-row seats are inde-pendent of each other and are all the same width. They can all be ad-justed to the “comfort” position.
To place the seat(s) in the comfort position
- Pull on control B.
The backrest reclines and the seat base pivots slightly.
To return the seat to its original position
- Pull on control B and allow the seat to come forward.
LONGITUDINAL ADJUSTMENT
Lift up control A, located at the front of the seat, and adjust the seat into the desired position.
Positioning the central seat belt
- Insert tongue C into the buckle on the right, then insert the second tongue D into the buckle on the left.

4
3
2
1
AB
3
2
1
0
4
A
B
C
D
E
F
IN BRIEF
I
15
D R I V I N G
LIGHTING CONTROL
Ring A
1 Off
2 Automatic lighting
3 Sidelamps
4 Dipped beams / Main beams
Ring B
Front foglamps
Rear foglamps
Windscreen wiper
3 Rapid wipe.
2 Normal wipe.
1 Intermittent wipe.
0 Off.
4 Automatic wipe by pressing downwards, and single wipe.
Note : To deactivateautomatic wipe :
- go to position 1, then return to position 0.
Rear screen wipe
Stop.
Intermittent.
Timed wash and wipe.
A Warning lamps for direction indicators and vehicle lamps
B Audio system controls
C Multifunction display controls
D Horn
E Optional function controls
F Cruise control and speed limiter

IN BRIEF
I
18
Air recirculation, automatic (depending on version)
Automatic comfort regulation
Air
conditioning
Rapid deicing / demisting of front and rear windows and rear view mirrors
Adjustment and display of temperature(comfort requirement)
REST function REST(retention of ventilation with (retention of ventilation with the engine switched off)the engine switched of
Adjustment of air blower speed
Adjustment of air distribution
Mode of adjustment for rear passengers
Black panel function (extinction of air conditioning displays and button backlighting)
Deicing / demisting of rear screen and rear view mirrorsAdjustment of air blower speed
DRIVER’S AND PASSENGER’S CONTROL PANEL REAR PASSENGERS’ CONTROL
PANEL
V E N T I L A T I O NA u t o m a t i c a i r c o n d i t i o n i n g
With additional air conditioning (no warm air distribution)
Temperature adjustment

A
IN BRIEF
I
20
M O N I T O R I N G
Seat belts not fastened / unfastened warning lamp
This warning lamp informs you if the driver’s or front passenger’s seat belt is not fastened (depend-ing on model), and if the front pas-senger’s (depending on model) or the second- and third-row passen-gers’ seat belts are unfastened. The lit up positions represent those whose seat belts are not fastened / unfastened.
Locking from inside
You can use electrical central locking or unlocking by pressing on button A.
If one of the doors is open or is not closed properly, central lock-ing will not work.
Anti-intrusion security
When starting the engine, the sys-tem automatically locks the doors once you reach approximately 10 km/h (approximately 6 mph).
Tyre defl ation detection
This function warns you if a tyre is defl ated or punctured.
This system does not absolve the driver of the need to regularly check the tyre pressures.
The SERVICE warning lamp lights up, and a ve-hicle outline is displayed, accompanied by a mes-sage and a sound signal.
Defl ation warning
The STOP warning lamp lights up, and a vehicle outline is displayed, ac-companied by a message and a sound signal.
Puncture

II
23
R E M O T E C O N T R O L
Guide-me-home lighting
A press on button C operates the guide-me-home lighting (lighting of the sidelamps, dipped beams, number plate lamps and side light-ers (located underneath the exte-rior rear view mirrors).
A second press before the end of the timing cancels the guide-me-home lighting.
Vehicle location
To locate the vehicle on a carpark, press button A. The location of the vehicle is revealed by :
- the fl ashing of the direction indi-cators and side repeaters for a few seconds,
- the lighting of the interior lamps for around 30 seconds,
- the lighting of the side lighters.
The vehicle remains locked.
Foldaway and ejection of the key
Button D folds the key in and out of its housing in the remote control.
If you do not press on button D, you could damage the mechanism.
Simultaneous use of other high frequency equipment (mobile tele-phones, domestic alarms, etc.) may interfere temporarily with the opera-tion of the remote control. If it malfunctions on a permanent basis, you must re-initialise the remote control.
Except for re-initialisation, the remote control cannot function while the key is in the ignition, even with the ignition switched off.
Be aware that an inadvertent manipulation of the remote con trol in your pocket could cause the vehicle doors to unlock without your knowl -edge.
However, if no door is opened within thirty seconds following an unlock-ing, the doors will automatically relock.
Warning : there is a risk of damage if the replacement battery is not in conformity.
Use only those batteries that are identical or equivalent to those recom-mended by CITROËN.Use only those batteries that are identical or equivalent to those recom-Use only those batteries that are identical or equivalent to those recom-
Remote control battery spent
This information is given by a message on the multifunction screen, accompa-nied by a sound signal and the lighting of the SERVICE warning lamp.
Changing the remote control battery
Detach the housing to access the battery.
Battery : CR 0523, 3V.
Re-initialising the remote control
After a change of battery, it is necessary to re-initialise the remote control. For that, switch on the ignition and immediately press butto n A on your remote control until the action desired is triggered. This manœ uvre may take some ten seconds.
Note : Make a careful note of the numbers for your keys and remote con-trol on the ASSISTANCE card. Keep this in a safe place.
Do not throw away spent batteries. Return them to a CITROËN dealer or to an approved collection point (photo shops, etc.).

34
II
Left hand direction indicator
See «Signalling»
Sidelamps
See «Signalling»
Right hand direction indicator
See «Signalling»
Dipped beams
See «Signalling»
Foglamps (rear)
See «Signalling»
Main beams
See «Signalling»
Front foglamps
See «Signalling»
The direction indicators operate simultaneously when the hazard lamps are activated.
Direction indicator and lighting lamps
W A R N I N G L A M P S

L
J
H
MR
O
M
JLH
OO
R
K
N
42
II
M U L T I F U N C T I O N S C R E E N A
To activate/deactivate the automatic guide-me-home lighting :
1. Press on O.
2. Use J or M to select the sub-menu for confi guration of your vehicle, then confi rm your choice with a press on L.
3. Select guide-me-home lighting, by pressing J or M.
4. The system tells you whether the function status is active or inactive. Modify this status with a press on K or N.
5. Validate with a press on L.
To activate/deactivate the electronic parking brake automatic functions :
1. Press on O.
2. Use J or M to select the sub-menu for confi guration of your vehicle, then confi rm your choice with a press on L.
3. Select electronic automatic parking brake by pressing J or M.
4. The system tells you whether the function status is active or in active. Modify this status with a press on K or N.
5. Validate with a press on L.
PERSONALISATION and CONFIGURATION
To activate/deactivate rear screen wipe when you engage reverse gear :
1. Press on O.
2. Use J or M to select the sub-menu for personalisation-con-fi guration of your vehicle, then confi rm your choice with a press on L.
3. Select rear wipe by pressing Jor M.
4. The system tells you whether the function status is active or inactive. Modify this status with a press on K or N.
5. Validate with a press on L.

L
J
H
MR
OO
M
JLH
OO
R
K
N
II
43
M U L T I F U N C T I O N S C R E E N A
To activate/deactivate door selectivity :
1. Press on O.
2. Use J or M to select the sub-menu for confi guration of your vehicle, then confi rm your choice with a press on L.
3. Select the access point by pressing J or M.
4. The system tells you the status of the doors/tailgate. Modify this status with a press on K or N.
5. Validate with a press on L.
To activate/deactivate lighting of daytime-running lamps (de pending on country) :
1. Press on O.
2. Use J or M to select the sub-menu for confi guration of your vehicle, then confi rm your choice with a press on L.
3. Select lighting of daytime-running lamps by pressing J or M.
4. The system tells you the status (active/inactive) of this function . Modify this status with a press K or N.
5. Validate with a press on L.