stop start Citroen GRAND C4 PICASSO RHD 2016 2.G Owner's Guide

126
Key not detected
Back-up starting
When the electronic key is in the recognition zone   and,   after   pressing   the   "START/STOP"  
b

utton,   the   engine   does   not   start:
F
 
P
lace   the   gear   selector   at   P or N for
vehicles
  with   an   automatic   gearbox   or  
n

eutral   for   vehicles   with   a   manual   gearbox.
F
 
I
nsert   the   electronic   key   in   the   back-up  
re

ader.
F
 
W

ith
 
the
 
electronic
 
key
 
inside
 
t

he vehicle, press the "
S TA R T/
STOP "
 
button.
The
 
engine
 
stops
 
and
 
the
 
steering
 
c

olumn
 
locks.
F
 
I

mmobilise
 
the
 
vehicle.
F
 
P

lace
 
the
 
gear
 
selector
 
at
 
P or N for
vehicles
 
with
 
an
 
automatic
 
gearbox,
 
or
 
n

eutral
 
with
 
a
 
manual
 
gearbox.
Switching off the engine
If the vehicle is not immobilised, the e
ngine   will   not   stop.
Do not leave your vehicle with the
electronic
  key   still   inside. F
 
P
ress   the   brake   pedal   on   vehicles   with   an  
a

utomatic   gearbox,   or   fully   declutch   with   a  
m

anual
 g
earbox.
F
 
P
ress   the   "START/STOP"   button.
The
  engine   starts.
Switching
  off   the   engine   leads   to   a   loss  
o

f   braking   assistance.
Driving

127
When the electronic key is not detected or is no   longer   in   the   recognition   zone,   a   message  
a

ppears   in   the   instrument   panel   when   closing   a  
d

oor   or   trying   to   switch   off   the   engine.
Emergency switch-off
In the event of an emergency only, the   engine   can   be   switched   off  
wi

thout
 c
onditions.
Press
  the   "START/STOP"   button   for  
a

bout   3   seconds.
In
 
this
 
case   the   steering   column   locks   as   soon  
a

s
 
the
 
vehicle   stops.
F
 
T

o
 
confirm
 
the
 
instruction
 
to
 
s

witch
 
off
 
the
 
engine,
 
press
 
the
 
"

START/STOP"
 
button
 
for
 
about
 
3

 
seconds.Back-up switch off
In the event of a fault with the electronic key, c ontact   a   CITROËN   dealer   or   a   qualified  
w

orkshop.
4
Driving

128
Switching the ignition on
( without
 s
tarting)
With the ignition on, the system goes i
nto   energy   economy   mode   when  
n

ecessary   to   maintain   the   state   of  
c

harge   of   the   battery.
With
 
the   electronic   key   in   the   reader   or   the  
K

eyless   Entry   and   Starting   key   inside   the  
v

ehicle,   pressing   the   "START/STOP"   button,  
w

ith no action on the pedals
, allows the
ignition   to   be   switched   on.
F  
P
ress   the   "START/STOP"   button,  
t

he   instrument   panel   comes   on  
b

ut   the   engine   does   not   start.
F
 
P

ress   the   button   again   to   switch   off   the  
i

gnition   and   so   allow   the   vehicle   to   be  
lo

cked.
Anti-theft protection
Electronic engine immobiliser
The keys contain an electronic chip which has a
  secret   code.   When   the   ignition   is   switched  
o

n,   this   code   must   be   recognised   in   order   for  
s

tarting   to   be   possible.
This
  electronic   engine   immobiliser   locks   the  
e

ngine   management   system   a   few   minutes  
a

fter   the   ignition   is   switched   off   and   prevents  
s

tarting   of   the   engine   by   anyone   who   does   not  
h

ave   the   key.
In
  the   event   of   a   malfunction,   you   are   informed  
b

y   a   message   in   the   instrument   panel   screen.
In
 
t
his  
c
ase,  
y
our  
v
ehicle  
d
oes  
n
ot  
s
tart;  
c
ontact  
a

  CITROËN   dealer   if   required.
Driving

131
With the vehicle stationary, the parking brake is automatically applied when the engine
is switched off
  by   pressing   the   START/STOP  
b

utton. Application
  of   the   parking   brake  
i

s   confirmed   by   illumination   of  
t

he   brake   indicator   lamp   and  
t

he P indicator   lamp   in   the   control  
l

ever,   accompanied   by   the   display   of  
t

he
 m
essage
 "
Parking
 b
rake
 a
pplied".
With
  the   engine   stalled   or   in   STOP  
m

ode   of   Stop   &   Start,   automatic  
a

pplication   does   not   take   place.
In
  automatic   mode,   you   can   manually  
a

pply  
o
r  
r
elease  
t
he  
p
arking  
b
rake  
u
sing  
t

he   control   lever.
Automatic operation
Automatic release
The complete release of the parking brake   is   confirmed   by   the   brake  
i

ndicator   lamp   and   the   P   indicator  
l

amp   in   the   control   lever   going   off,  
a

ccompanied   by   the   display   of   the  
m

essage   "Parking   brake   released".
When stationary with the engine running, do not depress   the   accelerator   pedal   unnecessarily, y

ou   risk   releasing   the   parking   brake.
Ensure first that the engine is running and the driver's   door   is   properly   closed.
The
  electric   parking   brake   releases
automatically and progressively when you
press
  the   accelerator:
F
 
M
anual   gearbox:   fully   depress   the   clutch  
p

edal,   engage   1
st or reverse gear; press t
he
 
accelerator
 
pedal   and   let   up   the   clutch  
ped

al.
F
 
A

utomatic
 
gearbox:   select   position   D, M or
R
 
then
 
press
 
the
  accelerator.
Automatic application
With an automatic gearbox, if the brake d oes   not   release   automatically,   check  
t

hat   the   front   doors   are   correctly   closed.
4
Driving

135
SituationsConsequences
Display   of   the   message   "Parking brake fault "
  and   these  
w

arning
 lam
ps: The
  parking   brake   is   faulty,   the   manual   and   automatic   functions   may   not   operate.
When stationary ,
  to   immobilise   your   vehicle:
-
 
P
ull   and   hold   the   control   lever   for   about   7   to   15   seconds,   until   the   warning   lamp  
c

omes   on   in   the   instrument   panel.
If
  this   procedure   does   not   work,   you   should   make   your   vehicle   safe:
-
 
P
ark   on   a   level   sur face.
-
 
E
ngage   a   gear   with   a   manual   gearbox,   or   place   the   gear   selector   at   position   P
with
  an   automatic   gearbox.
-
 
I
f   possible,   fit   a   wheel   chock.
Call
  on   a   CITROËN   dealer   or   a   qualified   workshop.
Display
  of   the   message   "Parking brake fault "
  and   these  
w

arning
 lam
ps: -
 
T
he   parking   brake   does   not   have   its   full   per formance   to   securely   hold   the   vehicle  
i

n   all   situations.
You
  should   make   your   vehicle   safe:
-
 
P
ark   on   a   level   sur face.
-
 
E
ngage   a   gear   with   a   manual   gearbox,   or   place   the   gear   selector   at   position   P
with
  an   automatic   gearbox.
-
 
I
f   possible,   fit   a   wheel   chock.
Call
  on   a   CITROËN   dealer   or   a   qualified   workshop.
The
  flashing   of   the   P   warning   lamps   on   starting   the   vehicle   indicates   that   the   parking  
b

rake   is   not   correctly   applied.
As
  soon   as   possible,   stop   the   vehicle   and   try   to   completely   release   the   parking   brake,  
u

sing   the   control   lever,   with   your   foot   on   the   brake   pedal.
Display
  of   the   message   "Battery fault "
  and   this   warning   lamp:-
 
T
he   state   of   charge   of   the   battery   is   very   low   and   requires   immobilisation   of   the  
v

ehicle   in   a   safe   place:   engage   a   gear   with   a   manual   gearbox   or   fit   a   chock   to  
o

ne   of   the   wheels.
-
 
O
nce   the   battery   is   completely   discharged,   the   controls   do   not   operate:   to  
r

elease   the   parking   brake,   call   on   a   CITROËN   dealer   or   a   qualified   workshop.
4
Driving

138
Automatic gearbox
This gearbox offers two driving modes.
-  a utomated  mode   for   automatic  
m

anagement   of   the   gears   by   the   gearbox,  
w

ithout   any   action   on   the   part   of   the   driver,
-
 
m
anual
 
mode   for   sequential   gear   changing  
b

y   the   driver   using   the   steering   mounted  
p

addles.
P.
 Pa

rk.
-
 
I
mmobilisation   of   the   vehicle,   parking   brake  
a

pplied   or   released.
-
 
S
tarting   the   engine.
R.
 R

everse.
-
 
R
eversing,   vehicle   stationary   and   engine   at  
i

dle.
N.
 N

eutral.
-
 
I
mmobilisation   of   the   vehicle,   parking   brake  
a

pplied.
-
 
S
tarting   the   engine.
D.
 A

utomatic
 ope
ration.
M.
 M

anual   operation   with   sequential   changing  
o

f   the   six   gears.Gear selector lever
To select position P,   move   the   gear  s
elector   to   the   highest   position  
(

towards  R),
  then   push   it   for wards   and  
t

hen   to   the   left.
Only
  engage   it   when   the   vehicle   is   at   a  
c

omplete   stop.   In   this   position,   the   front  
w

heels   are   locked.   Ensure   that   the   gear  
s

elector   is   correctly   positioned.
To
  move   the   gear   selector,   switch   on  
t

he   ignition   or   start   the   engine.
If
  the   battery   is   not   sufficiently   charged,  
i

t   is   not   possible   to   move   the   gear  
s

elector.
To
  come   out   of   position   P
,   move   the  
g

ear   selector   to   the   right   to   the   desired  
p

osition,   while   keeping   your   foot   on   the  
b

rake
 ped
al.
It
 
is
 
possible
 
to
 
change
 
from
 
one
 
mode
 
t

o
 
the
 
other
 
at
 
any
 
time.
With
 
the
 
automated
 
mode,
 
you
 
can
 
t

emporarily
 
take
 
control
 
of
 
the
 
gear
 
c

hanges
 
at
 
any
 
time.
Driving

143
Depending on the driving situation and your vehicle's   equipment,   the   system   may   advise  
y

ou   to   skip   one   or   more   gears.
You
  can   follow   this   instruction   without   going  
t

hrough   the   intermediate   gears..
Gear efficiency indicator
System which reduces fuel consumption by recommending the most suitable gear.
T he   system   adapts   its   gear   change  
r

ecommendation   according   to   the  
d

riving   conditions   (gradient,   load, ...)  
a

nd   the   demands   of   the   driver   (power,  
a

cceleration,   braking,   ...).
The
  system   never   suggests:
-
 
e
ngaging   first   gear,
-
 enga

ging
 r
everse
 g
ear.
The
  information   appears   in   the   instrument  
p

anel   in   the   form   of   an   arrow.
On
  vehicles   with   manual   gearbox,   the   arrow  
m

ay   be   accompanied   by   the   recommended  
g

e a r.
The gear engagement recommendations
must not be considered compulsory.
This is because the configuration of the
road, traffic density and safety remain
impor tant factors in the choice of the best
g e a r.
The
  gear   efficiency   indicator   system   does   not  
r

eplace   the   need   for   vigilance   on   the   part   of   the  
d

river.
With
  an   automatic   gearbox,   the   system   is   only   active   in   manual   mode.
On
  BlueHDi   Diesel   135   and   150   versions   with  
m

anual   gearbox,   in   certain   driving   conditions  
t

he   system   may   suggest   changing   into   neutral  
s

o   that   the   engine   can   go   into   standby   (STOP  
m

ode   with   Stop   &   Start).   In   this   case,   N is
displayed
  in   the   instrument   panel.Example:
This
  function   cannot   be   deactivated.
-
 
Y
ou   are   in   third   gear.
-
 
Y
ou   press   the   accelerator   pedal.
-
 
T
he   system   may   suggest   that   you   engage  
a

  higher   gear.
4
Driving

144
Stop & Start
The Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine   restarts   automatically   -   START   mode   -   as   soon   as   you   want   to   move   off.   The   restart   takes   place   instantly,   quickly   and   silently.
Operation
Going into engine STOP
mode
This indicator lamp comes on in the instrument panel   and   the   engine   goes   into   standby  
au

tomatically:
-
 
w
ith a manual gearbox ,
  at   speeds   below  
1

2   mph   (20   km/h),   or   vehicle   stationary  
(

with   PureTech   130,   THP   165   and  
B

lueHDi 100,   115   and   120   versions),   when  
y

ou   place   the   gear   lever   in   neutral,   and   you  
r

elease   the   clutch   pedal,
-
 
w
ith an automatic gearbox , with the
vehicle stationary, when you press the
brake
  pedal   or   place   the   gear   selector   lever  
a

t position N . Never
  refuel   with   the   engine   in   STOP  
m

ode;   you   must   switch   off   the   ignition  
w

ith   the   START/STOP   button.
For
  your   comfort,   during   parking  
m

anoeuvres,   STOP   mode   is   not  
a

vailable   for   a   few   seconds   after  
c

oming   out   of   reverse   gear.
The
  Stop   &   Start   system   does   not   affect  
t

he functionality of the vehicle, such as
for
  example,   braking,   power   steering...
Special cases: STOP mode not
available
STOP mode is not invoked when:
-  t he   driver's   door   is   open,
-
 
t
he   driver's   seat   belt   is   not   fastened,
-
 
t
he   vehicle   has   not   exceeded   6   mph  
(10
  km/h)   since   the   last   engine   start   using  
t

he   START/STOP   button,
-
 
t
he   electric   parking   brake   is   applied   or  
be

ing
 a
pplied,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   selected,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
In this case, this indicator lamp flashes for   a   few   seconds   then   goes   off.
This operation is perfectly normal.
Per fect
 
for
 
urban
 
use,
 
the
 
Stop
 
&
 
Start
 
system
 
reduces
 
fuel
 
consumption
 
and
 
exhaust
 
emissions
 
as
 
well
  as   the   noise   level   when   stationary.
If
 
your
 
vehicle
 
is
 
fitted
 
with
 
the
 
system,
 
a
 
time
 
c

ounter
 
calculates
 
the
 
sum
 
of
 
the
 
periods
 
in
 
S

TOP
 
mode
 
during
 
a
 
journey.
 
It
 
resets
 
itself
 
to
 
z

ero
 
every
 
time
 
the
 
ignition
 
is
 
switched
 
on
 
with
 t
he
 
START/STOP
 
button.
Driving

145
Going into engine START mode
This indicator lamp goes off and the engine s tarts a utomatically:
-
 
w

ith a manual gearbox , when you fully
depress
  the   clutch   pedal,
-
 
w

ith an automatic gearbox :
●
 
g

ear   selector   in   position   D or M, when
you
  release   the   brake   pedal,
●
 
o

r
 
gear   selector   in   position   N   and   brake  
p

edal   released,   when   you   place   the   gear  
s

elector at position D or M ,
●
 
o

r
 
when   you   engage   reverse. START
  mode   is   invoked   automatically   when:
-  y ou   open   the   driver's   door,
-
 
y
ou   unfasten   the   driver's   seat   belt,
-
 
t
he   speed   of   the   vehicle   exceeds   15   mph  
(

25   km/h)   with   a   manual   gearbox   (2   mph  
(

3   km/h)   with   PureTech   130,   THP   165   and  
B

lueHDi   100,   115   and   120   versions)   and  
2 m

ph   (3   km/h)   with   an   automatic   gearbox,
-
 
t
he   electric   parking   brake   is   being   applied,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   for   control   of   a   system.
Special cases: START invoked
automaticallyIn some circumstances, such as the need to maintain   a   comfortable   temperature   in   the  
p

assenger   compartment,   it   may   be   necessary  
t

o   deactivate   the   Stop   &   Start   system.
The
  system   can   be   deactivated   at   any   time,  
o

nce   the   ignition   is   on.
If
  the   engine   is   in   STOP   mode,   it   then   restarts.
The
  Stop   &   Start   system   is   automatically  
r

eactivated   every   time   the   ignition   is  
s

witched on.
Manual deactivation/
reactivation
In this case this indicator lamp flashes for   a   few   seconds,   then   goes   off.
This operation is perfectly normal. Select
  "Stop   &   Start"   to   deactivate   the   system.
This   is   confirmed   by   the   illumination  
o

f   this   indicator   lamp.
Using   the   dynamic   cruise   control  
d

eactivates   the   Stop   &   Start   system.
Deactivation
  of   Stop   &   Start   is   done   in   the  
D

riving
 
menu   of   the   touch   screen   tablet.
Select   "Stop   &   Start"   again   to   reactivate   the  
s

ystem.
This   is   confirmed   by   the   illumination  o
f   this   indicator   lamp.
4
Driving

146
Operating fault
Have it checked by a CITROËN dealer or a qualified w orkshop.
In
  the   event   of   a   fault   in   STOP   mode,   the   vehicle
 m

ay   stall.
All
  of   the   instrument   panel   warning   lamps   come on.
Depending on version, an alert message may also   be   displayed,   asking   you   to   place   the   gear  
s

elector lever at position N   and   put   your   foot   on  
t

he   brake   pedal.
It is then necessary to switch off the ignition and start   the   engine   again   using   the   "START/STOP" b

utton.
In the event of a fault with the system, this   indicator   lamp   flashes   for   a   few m

oments
 t
hen
 c
omes
 o
n
 c
ontinuously,
 a

ccompanied   by   a   message.
Opening the bonnet
Before
 
doing
 
anything
 
under
 
the
 
b

onnet,
 
deactivate
 
the
 
Stop
 
&
 
Start
 
s

ystem
 
to
 
avoid
 
the
 
risk
 
of
 
injury
 
related
 
t

o
 
an
 
automatic
 
change
 
to
 
START
 
m

ode.
Driving on flooded roads
Before
 
driving
 
through
 
a
 
flooded
 
road,
 
i

t
 
is
 
strongly
 
recommended
 
that
 
you
 
d

eactivate
 
the
 
Stop
 
&
 
Start
 
system.
For
 
more
 
information
 
on
 
Driving
advice ,
 
particularly
 
on
 
flooded
 
roads,
 
r

efer
 
to
 
the
 
corresponding
 
section. The
  Stop   &   Start   system   requires   a  
b

attery   of   advanced   technology   and  
sp

ecial
 c
haracteristics.
All
 
work   on   this   type   of   battery   must  
o

nly
  be   done   by   a   CITROËN   dealer  
or
 
a
  qualified   workshop.
For
 
more   information   on   the  
12 V
batter y ,
  refer   to   the   corresponding  
s

ection.
Driving