DAEWOO MATIZ 2003 Service Repair Manual

AUDIO SYSTEMS 9F–11
DAEWOO M-150 BL2
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
ApplicationNmLb-FtLb-In
Roof Antenna Retaining Screw3–27

9F –12 AUDIO SYSTEMS
DAEWOO M-150 BL2
SCHEMATIC AND ROUTING DIAGRAMS
AUDIO SYSTEM CIRCUIT
(Left–Hand Drive Shown, Right–Hand Drive Similar)
D19D209B

DAEWOO M-150 BL2
SECTION 9G
INTERIOR TRIM
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9G-2. . . . . . . . . . . . . . . . . .
Interior Trim Panels 9G-2. . . . . . . . . . . . . . . . . . . . . . . .
Pressure Relief Vent 9G-2. . . . . . . . . . . . . . . . . . . . . . .
Floor Console 9G-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking Brake Cable Cover 9G-2. . . . . . . . . . . . . . . . .
Floor Carpet 9G-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Component Locator 9G-3. . . . . . . . . . . . . . . . . . . . . . . .
Interior Trim 9G-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 9G-4. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 9G-4. . . . . . . . . . . . . . . . . . . . . . . . . .
Front Door Trim Panel (Standard) 9G-4. . . . . . . . . . .
Front Door Trim Panel (Deluxe) 9G-5. . . . . . . . . . . . .
Rear Door Trim Panel (Standard) 9G-6. . . . . . . . . . . .
Rear Door Trim Panel (Deluxe) 9G-7. . . . . . . . . . . . . .
Rear Door Interior Garnish Molding 9G-8. . . . . . . . . .
Rear Door Exterior Garnish Molding 9G-9. . . . . . . . . Tailgate Trim Panel 9G-9. . . . . . . . . . . . . . . . . . . . . . . .
A–Pillar Trim Panel 9G-10. . . . . . . . . . . . . . . . . . . . . . .
Upper B–Piller Trim Panel 9G-10. . . . . . . . . . . . . . . . .
Lower B–Pillar Trim Panel 9G-11. . . . . . . . . . . . . . . . .
C–Pillar Trim Panel 9G-11. . . . . . . . . . . . . . . . . . . . . . .
Rear Parcel Shelf 9G-12. . . . . . . . . . . . . . . . . . . . . . . .
Rear Parcel Side Shelf 9G-13. . . . . . . . . . . . . . . . . . . .
Front Rocker Trim Panel 9G-13. . . . . . . . . . . . . . . . . .
Rear Rocker Trim Panel 9G-14. . . . . . . . . . . . . . . . . . .
Floor Console 9G-15. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking Brake Cable Cover 9G-15. . . . . . . . . . . . . . . .
Floor Carpet 9G-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage Compartment Wheelhouse
Trim Panel 9G-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Tools and Equipment 9G-18. . . . . . . . . . . . . .
Special Tools Table 9G-18. . . . . . . . . . . . . . . . . . . . . . .

9G –2 INTERIOR TRIM
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
INTERIOR TRIM PANELS
The interior trim panels are molded plastic and fasten
with screws or plastic clips.
PRESSURE RELIEF VENT
When all the windows are closed and the ventilation sys-
tem is on, the addition of outside air to the interior of the
vehicle causes a positive pressure within the vehicle. In
order to relieve the pressure, air is released through one
pressure relief vents. The pressure relief vent is located
in the luggage compartment, behind the spare wheel.
FLOOR CONSOLE
The floor console fits over the tunnel in the floor of the
vehicle and extends from under the center of the instru-
ment panel to the front seat area. The floor console con-
tains the transaxle shift lever and a cupholder.
The sensing and diagnosis module (SDM) for the airbag
system is located under the floor console.
PARKING BRAKE CABLE COVER
The parking brake cable cover should be removed to ad-
just the free play of the parking brake cable.
FLOOR CARPET
The molded one-piece floor carpet goes over both the
front and the rear floor pans.

INTERIOR TRIM 9G–3
DAEWOO M-150 BL2
COMPONENT LOCATOR
INTERIOR TRIM
D19E402A
1. A–Pillar Trim Panel
2. B–Pillar Upper Trim Panel
3. C–Pillar Trim Panel
4. Front Rocker Trim Panel
5. B–Pillar Lower Trim Panel
6. Rear Rocker Trim Panel
7. Rear Parcel Side Shelf8. Wheel House Trim Panel
9. Floor Console
10. Parking Brake Cable Cover
11. Console Cover Assembly
12. Deposit Box
13. Console Boot Assembly

9G –4 INTERIOR TRIM
DAEWOO M-150 BL2
REPAIR INSTRUCTIONS
ON–VEHICLE SERVICE
D109E532
FRONT DOOR TRIM PANEL
(STANDARD)
Tool Required
KM 475–B Trim Remover.
Removal Procedure
1. Remove the door pull from the front door.

Remove the screws (1).

Remove the door pull (2).
D109E533
2. Remove the inside door handle.

Remove the screw (1).

Disconnect the inside door handle rod (2).

Pry off the inside door handle (3).
D109E534
3. Remove the window regulator handle from the front
door.

Using a cloth, pull out the clip (1).

Remove the regulator handle (2).

INTERIOR TRIM 9G–5
DAEWOO M-150 BL2
D109E535
4. Pry off the trim panel using a trim remover KM 475–B.
Notice: Make sure to cover the remover with cloth to
prevent the paint damage of the door.
D109E536
Installation Procedure
1. Install the trim panel.
2. Install the window regulator handle with the clip.
3. Install the inside door handle and the door pull with
the screws.
D19E537A
FRONT DOOR TRIM PANEL
(DELUXE)
Removal Procedure
1. Remove the inside door handle. Refer to Section 9P,
Doors.
2. Remove the power window/mirror control switch as-
sembly from the front door.

Remove the screws (1).

Remove the power window/mirror control switch
assembly (2).

Disconnect the electrical connectors (3).
D19E538A
3. Remove the trim panel.

Remove the screws (1).

Remove the clips (2).

Remove the trim panel (3).

9G –6 INTERIOR TRIM
DAEWOO M-150 BL2
D109E539
4. Remove the inside channel weatherstrip. Refer to
Section 9P, Doors.
5. Remove the map pocket from the door trim.

Remove the screws (1).

Remove the map pocket (2).
D19E540A
Installation Procedure
1. Install the map pocket to the door trim with the
screws.
2. Install the inside channel weatherstrip. Refer to Sec-
tion 9P, Doors.
3. Install the door trim panel with the screws and the
clips.
4. Install the power window/mirror control switch assem-
bly with the screw.
5. Install the inside door handle. Refer to Section 9P,
Doors.
D109E541
2
REAR DOOR TRIM PANEL
(STANDARD)
Tool Required
KM 475–B Trim Remover.
Removal Procedure
1. Remove the inside door handle.

Remove the screw (1).

Disconnect the inside door handle rod.

Pry off the inside door handle (2).
D109E542
2. Remove the door pull.

Remove the screws (1).

Remove the door pull (2).

INTERIOR TRIM 9G–7
DAEWOO M-150 BL2
D109E543
3. Remove the window regulator handle from the rear
door.

Using a cloth, pull out the clip (1).

Remove the regulator handle (2).
D109E544
4. Pry off the trim panel using a trim remover KM 475–B.
Notice: Make sure to cover the remover with cloth to
prevent the paint damage of the door.
D109E545
Installation Procedure
1. Install the trim panel.
2. Install the window regulator handle with the clip.
3. Install the inside door handle and the door pull with
the screws.
D109E546
REAR DOOR TRIM PANEL (DELUXE)
Removal Procedure
1. Remove the inside door handle. Refer to Section 9P,
Doors.
2. Remove the window regulator handle from the rear
door. Refer to Section 9P, Doors.
3. Remove the door pull.

Remove the screw (1).

Remove the door pull (2).

9G –8 INTERIOR TRIM
DAEWOO M-150 BL2
D109E547
4. Remove the trim panel.

Remove the screws (1).

Remove the clips (2).

Remove the trim panel (3).
5. Remove the inside channel weatherstrip. Refer to
Section 9P, Doors.
D109E548
Installation Procedure
1. Install the inside channel weatherstrip. Refer to Sec-
tion 9P, Doors.
2. Install the trim panel with the screws and the clips.
3. Install the door pull with the screw.
4. Install the window regulator handle. Refer to Section
9P, Doors.
5. Install the inside door handle. Refer to Section 9P,
Doors.
D109E549
REAR DOOR INTERIOR GARNISH
MOLDING
Removal Procedure
1. Pry off interior garnish molding.

Pry off the garnish molding caps (1).
D109E550
Installation Procedure
1. Install the interior garnish molding.