DODGE RAM SRT-10 2006 Service Repair Manual

4.FIELD DRIVER CIRCUIT SHORTED TO VOLTAGE
Measure the voltage between the (K20) generator field driver circuit in
the generator harness connector and battery negative.
Is the voltage greater than 1 volt?
Ye s>>
Repair the (K20) Generator field driver circuit shorted to
voltage.
No>>
Go To 5
5.ECM
While monitoring with scan tool, connect a jumper wire between the driver circuit and the return circuit in the alter-
nator connector.
Did the DTC return?
Ye s>>
Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Repair complete.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)

P0628-LOW VOLTAGE DETECTED AT THE FUEL LIFT PUMP
For a complete wiring diagramRefer to Section 8W.

When Monitored:
Whilethekeyison.
Set Condition:
The commanded signal to the fuel lift pump circuit in the TIPM does not matchthe feedback signal from the
fuel lift pump circuit.
Possible Causes
WIRING HARNESS
TIPM
FUEL LIFT PUMP CONTROL CIRCUIT SHORTED TO EXTERNAL VOLTAGE
FUEL LIFT PUMP CONTROL CIRCUIT OPEN
FUEL LIFT PUMP GROUND CIRCUIT OPEN
FUEL LIFT PUMP GROUND CIRCUIT SHORTED TO EXTERNAL VOLTAGE
ECM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.POWER AT TPIM
Using a voltmeter, measure the voltage on the Battery Supply wire to the TIPM.
Turn the ignition on, engine off.
Does the voltmeter show battery voltage?
No>>
Fix or replace the open circuit in the Battery Supply Circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
Ye s>>
Go To 2
2.DAMANGED WIRING HARNESS
Turn Ignition off.
Disconnect the ECM and TIPM connectors. Inspect the connectors for signs of damage or corrosion.
NOTE: Check connectors - Clean/repair as necessary.
Are any pins damaged?
Ye s>>
Fix or replace the harness
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 5
3.FUEL LIFT PUMP CONTROL CIRCUIT OPEN
Using an ohmmeter, measure the resistance of the lift pump control circuitbetween the ECM connector and the
TIPM connector.
Is the resistance less than 10 Ohms?
Ye s>>
Go To 4
No>>
Repair the open ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)

4.FUEL LIFT PUMP CONTROL CIRCUIT SHORTED TO EXTERNAL VOLTAGE
Using a voltmeter, measure the voltage between battery negative and the lift pump control circuit at the TPIM con-
nector.
Is the voltage greater than 1 volt?
No>>
Go To 5
Ye s>>
Fix or replace the harness.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
5.FUEL LIFT PUMP CONTROL CIRCUIT SHORTED TO OTHER CIRCUITS
Using an ohmmeter, measure the resistance between the lift pump control circuit in the ECM connector and all other
circuits in the ECM connectors.
Is the resistance less than 10 Ohms?
Ye s>>
Fix or replace the harness.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 6
6.FUEL LIFT PUMP CONTROL CIRCUIT SHORTED TO EXTERNAL VOLTAGE
Connect the ECM and TIPM connectors.
Using a back probing tool 6801, back probe the lift pump control circuit in from TIPM connector.
Toggle the lift pump actuator with the Electronic Service Tool.
Using a 12 volt test light connected to battery negative, check the lift pump circuit at the TIPM connector.
NOTE: The test light must illuminate brightly.
Compare the brightness to that of a direct connection to the battery.
Does the test light cycle on and off and illuminate brightly?
No>>
Replace the ECM
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
Ye s>>
Go To 7
7.FUEL LIFT PUMP DRIVER CIRCUIT SHORTED TO OTHER CIRCUITS
Using a back probing tool, back probe the lift pump control circuit in the TIPM connector.
Toggle the lift pump actuator with the scan Tool.
Using a 12 volt test light connected to battery negative, check the lift pump control circuit at the TIPM connector.
NOTE: The test light must illuminate brightly.
Compare the brightness to that of a direct connection to the battery.
Does the test light cycle on and off and illuminate brightly?
Ye s>>
Te s t c o m p l e t e .
Perform Intermittent Condition test. (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)
No>>
Replace the TPIM
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)

P0629-HIGH VOLTAGE DETECTED AT THE FUEL LIFT PUMP
For a complete wiring diagramRefer to Section 8W.

When Monitored:
Whilethekeyison.
Set Condition:
The commanded signal to the fuel lift pump relay does not match the feedbacksignal from the fuel lift pump
relay.
Possible Causes
DAMAGED WIRING HARNESS
LIFT PUMP DRIVER CIRCUIT SHORTED TO GROUND
ECM
TIPM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.LIFT PUMP DRIVER CIRCUIT SHORTED TO GROUND
Turn the ignition on, engine off.
Disconnect the ECM and TIPM connectors.
NOTE: Check connectors - Clean/repair as necessary.
Using an ohmmeter, measure the resistance of the lift pump driver wire between the ECM connector and ground.
Is the resistance less than 10 Ohms?
Ye s>>
Fix or repair the wire harness.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 2
2.ECM
Turn Ignition off.
Connect the ECM and TIPM connectors.
Turn the ignition on, engine off.
Using a back probing tool 6801, back probe the lift pump logic pin in from TIPM connector.
Toggle the lift pump actuator with the Electronic Service Tool.
Using a 12 volt test light connected to battery negative, check the lift pump circuit at the TIPM connector.
NOTE: The test light must illuminate brightly.
Compare the brightness to that of a direct connection to the battery.
Does the test light cycle on and off and illuminate brightly?
Ye s>>
Go To 3
No>>
Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)

3.TIPM
Using a back probing tool 6801, back probe the lift pump power pin in from TIPM connector.
Toggle the lift pump actuator with the Electronic Service Tool.
Using a 12 volt test light connected to battery negative, check the lift pump circuit at the TIPM connector.
NOTE: The test light must illuminate brightly.
Compare the brightness to that of a direct connection to the battery.
Does the test light cycle on and off and illuminate brightly?
Ye s>>
Te s t c o m p l e t e .
Perform Intermittent Condition test. (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)
No>>
Replace the TPIM
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)

P0630-VIN NOT ENTERED ERROR
For a complete wiring diagramRefer to Section 8W.
When Monitored:
Whilethekeyison.
Set Condition:
The VIN was not calibrated into the ECM.
Possible Causes
VIN NOT CALIBRATED INTO ECM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.VIN NOT CALIBRATED INTO ECM
Using the scan tool, recalibrate the ECM with the proper VIN.
Did the DTC P0630 reset?
Ye s>>
Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Te s t C o m p l e t e .

P0633-SKIM SECRET KEY NOT ENTERED
For a complete wiring diagramRefer to Section 8W.
When Monitored:
Whilethekeyison.
Set Condition:
TheSKIMsecretkeywasnotcalibratedintotheECM.
Possible Causes
IMPROPER IGNITION KEY IS BEING USED
SKIM DTC’S
SKIM NOT CALIBRATED PROPERLY
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.SKIM DTC’S
With the scan tool, read SKIM DTCs.
Are any SKIM DTC’s present?
Ye s>>
Repair all SKIM DTC’s first.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 2
2.IMPROPER IGNITION KEY IS BEING USED
Verify that the proper ignition key is in the ignition lock on the steering column.
Are the proper keys being used?
Ye s>>
Go To 3
No>>
Use the proper key for the vehicle.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
3.SKIM NOT CALIBRATED PROPERLY
Using the scan tool, recalibrate the ECM with the proper SKIM secret key.
With the scan tool, erase DTCs.
Cycle the ignition switch from on to off to on.
With the scan tool, read DTCs.
Did the DTC reset?
No>>
Te s t C o m p l e t e .
Ye s>>
Verify information is correct and replace ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)

P0642-LOW VOLTAGE AT THE #2 SENSOR SUPPLY CIRCUIT
For a complete wiring diagramRefer to Section 8W.