FIAT DOBLO PANORAMA 2015 2.G Owners Manual

REPLACING AN
INTERIOR BULB
For the type of bulb and power
rating, see "Changing a bulb".
FRONT ROOF LIGHT
Roof light with
movable lens
Proceed as follows to replace the
bulbs:
❒remove roof light A fig. 165 working
at the points indicated by the arrows;
❒open the cover B fig. 166 as
indicated;
❒replace the bulb C fig. 167 releasing
the side contacts, insert the new
bulb and make sure that it is correctly
locked between the contacts;❒close the cover and secure the roof
light into its housing, making sure it
locks properly into place.
Roof light with spot
lights (where
provided)
Proceed as follows to replace the
bulbs:
❒operate in the points indicated by the
arrows and remove light A fig. 168;❒open protective flap B fig. 169;
❒replace the bulbs C releasing them
from the side contacts making sure
that the new bulbs are correctly
secured between the contacts;
❒close flap B fig. 169 and fix roof light
A fig. 168 in its housing, making sure
that it locks into place.
165F0V0070
166F0V0071
167F0V0072
168F0V0073
169F0V0074
167

REAR ROOF LIGHT
To replace the bulb, proceed as
follows:
❒remove roof light A fig. 170 working
at the points indicated by the arrows;
❒open the cover B fig. 171 as
indicated;❒replace the bulb C fig. 172 releasing
the side contacts, insert the new
bulb and make sure that it is correctly
locked between the contacts;
❒close the cover B fig. 171 and secure
the roof light into its housing, making
sure it locks properly into place.
Removable roof light
To replace the bulb, proceed as
follows:
❒press button A fig. 173 and extract
the removable roof light B;
❒remove the roof light, working at the
points indicated by the arrows;
❒replace bulb C fig. 174 releasing the
side contacts, insert the new bulb
and make sure that it is correctly
locked between the contacts;
REPLACING FUSES
INTRODUCTION
Fuses protect the electric system:
they blow in the event of a failure or
improper action on the system.
When a device does not work,
check the condition of its protective
fuse: the filament A fig. 175 must
be intact.
170F0V0075
171F0V0071
172F0V0072
173F0V0176
174F0V0177
168
IN AN EMERGENCY

If it is not, replace the blown fuse
with another having the same
amperage (same colour).
B intact fuse.
C fuse with damaged filament.
To change a fuse, use the tweezers
D located in the tool box or the
Fix & Go container (for
versions/markets where provided).
26)
105) 106) 107)
To identify the protective fuse, see
the tables on the following pages.ENGINE
COMPARTMENT FUSE
BOX
The fuse box fig. 177 is located on
the right-hand side of the engine,
next to the battery. To remove the
protective cover A fig. 176 and
access the fuse box, undo the two
fixing screws B.
27)175F0V0088
176F0V0081
177F0V0089
169

PASSENGER
COMPARTMENT FUSE
BOXES
To access the fuses, remove
snap-fitted protective cover A fig.
178.
The fuses are located in the two
fuse boxes shown in fig. 179.
178F0V0562
179F0V0563
170
IN AN EMERGENCY

Engine compartment fuse box
fig. 176 - fig. 177
DEVICE PROTECTED FUSE AMPERE
Remote control switch for opening swing door (Cargo version) F09 10
Single tone hornF10 10
Main beam headlights F14 15
Heated rear window F20 30
Fog lightsF30 15
Rear power socket F85 15
Passenger compartment power socket F86 15
171

Passenger compartment fuse boxes
fig. 178 - fig. 179
DEVICE PROTECTED FUSE AMPERE
Door locking/unlocking motors, dead lock actuator motors, tailgate unlocking
motorF38 20
Supply + battery for EOBD diagnosis socket, radio, tyre pressure monitoring
control unitF36 10
Windscreen/rear window washer pump F43 15
Electric window motor on passenger-side front door F48 20
Left low beam, headlight corrector F13 7,5
Electric window motor on driver-side front door F47 20
172
IN AN EMERGENCY

DEVICE PROTECTED FUSE AMPERE
Heated driver seat F1 10
Heated passenger seat F2 10
Cigar lighterF3 15
Third power socket on dashboard F4 20
Driver's side rear electric window F5 20
Passenger's side rear electric window F6 20
IMPORTANT
26) Never replace a blown fuse with metal wires or other material.
27) If you need to wash the engine compartment, take care not to directly hit the fuse box and the window wiper motors
with the water jet.
173

WARNING
105) If the replaced fuse blows again, contact a Fiat Dealership.
106) Never replace a fuse with another with a higher amp rating; DANGER OF FIRE. If a general protection fuse
(MEGA-FUSE, MIDI-FUSE) is activated, contact a Fiat Dealership. Before replacing a fuse, make sure that the ignition
key has been removed and that all the other services are switched off and/or disengaged.
107) Contact a Fiat Dealership if a safety system (airbags, brakes), engine system (engine, gearbox) or steering system
general protection fuse blows.
174
IN AN EMERGENCY

CHANGING A WHEEL
The vehicle is originally equipped
with the Fix&Go automatic quick
tyre repair kit (see instructions in the
next section). As an alternative,
the vehicle may have a normal-sized
spare wheel.
Wheel changing and correct use of
the jack and spare wheel call for
some precautions, as listed below.
108) 109) 110) 111)
Note for one-way
tyres
One-way tyres have a few arrows on
the side indicating the rotation
direction. If a wheel is changed
(when punctured, for example) the
direction of the arrows on the spare
wheel tyre may not coincide with
the rotation direction of the wheel to
be replaced.
In these conditions, too, the tyre still
maintains its safety features.Anyway, it is recommended to have
the wheel repaired and refitted as
soon as possible, as the best
performance is achieved when the
rotation direction of all tyres
coincides with the one indicated by
the arrows.
Please note that:
❒the jack weight is 4 kg;
❒the jack requires no adjustment;
❒the jack cannot be repaired and in
the event of a fault it must be
replaced by another original one;
❒no tool other than its cranking device
may be fitted on the jack.
To change a wheel, proceed as
follows:
❒stop the vehicle in a position that is
not dangerous for oncoming traffic
where you can change the wheel
safely. The ground should be flat
if possible, and sufficiently firm;
❒stop the engine and pull the
handbrake;
❒engage first gear or reverse;
❒wear the reflective safety jacket
(compulsory by law in certain
countries) before getting out of the
vehicle;❒indicate that the vehicle has broken
down using the devices required by
the law in the current country (e.g.
warning triangle, hazard lights, etc.);
❒for Cargo versions fig. 180: move the
left front seat forward and operate
lever A to access the tool bag; take it
to the wheel that needs replacing;
❒for Doblò/Doblò Combi versions fig.
181: open the rear doors, inside the
compartment on the rear right side,
take the tool bag, unhooking the
elastic band from the buckle, and
take it next to the wheel to be
changed;
❒take wheel spanner B fig. 182 and
the extension with pentagonal fitting
C; inside the load area, fit extension
C on bolt A; use spanner B to lower
the wheel by unwinding the wire;
180F0V0149
175

❒use the wheel dismantling spanner B
to remove the wheel from the vehicle
fig. 183;❒unscrew knob D fig. 184 and release
the rim from bracket E, removing it
from the hole of the rim;
❒for versions with alloy rims, remove
the press-fitted hub cap;
❒loosen the fixing bolts of the wheel to
be replaced by about one turn, using
the spanner provided;❒remove wedge D from the tool bag
and open it as shown in fig. 185;
❒place the wedge D behind the wheel
diagonally opposite the one you want
to replace fig. 186 to prevent the
vehicle from moving when it is raised.
181F0V0148
B
C
182F0V0150
183F0V0151
184F0V0193
185F0V0192
186F0V0153
176
IN AN EMERGENCY