Electric FORD MUSTANG 1969 Volume One Chassis

02-02-07
Brake System

02-02-07

ANTI-SKID CONTROL SYSTEM

RELEASE PAWL CAM PIN

RELEASE PAWL CAM LEVER

RELEASE CABLE

H
1636-
A

FIG. 10—Parking Brake Control Assembly

With Manual Release—Typical

power unit with mounting bracket is

riveted to the control assembly. The

vacuum actuated piston within the

unit is connected by a rod to the

upper end of the release lever (Fig. 9).

The lower end of the release lever ex-

tends out for alternate manual release
in the event of vacuum power failure

or for optional manual release at any

time.

Hoses connect the power unit and

the engine manifold to a vacuum re-

lease valve in the transmission neutral

safety switch.
The anti-skid control system con-

sists of three major components (Fig.

39).
Mechanically driven electromag-

netic sensors at each rear wheel; an

electronic control module mounted

under the glove box; a vacuum pow-

ered actuator attached to a bracket on

the inside of the right front frame rail

under the toe board.

The sensors consist of steel rings

having teeth on their outer diameters,

pressed on each axle shaft just out-

board of the wheel bearing. The teeth

rotate past corresponding teeth on the

inside diameter of stationary steel

rings mounted in the bearing retain-

ers.
Also mounted in the retainers, are

ring-shaped permanent magnets and

coils of wire. Two wires from each

sensor connect the sensors to the con-

trol module.

The control module consists of solid

state electronic components sealed in

a container. It is connected to the sen-

sors and to a solenoid on the actuator.

The actuator is similar to a vacuum

brake booster and consists of three

parts.
A chamber divided by a vacuum

suspended diaphragm; a hydraulic cyl-

inder connected to the diaphragm; and

a solenoid connected electrically to the

control module.

IN-VEHICLE ADJUSTMENTS AND REPAIRS

After any brake service work, ob-

tain a firm brake pedal before moving

the vehicle. Riding the brake pedal

(common on left foot application)

should be avoided when driving the

vehicle.

BRAKE SHOE ADJUSTMENTS—

DRUM BRAKES

The hydraulic drum brakes are

self-adjusting and require a manual

adjustment only after the brake shoes

have been relined, replaced, or when

the length of the adjusting screw has

been changed while performing some

other service operation. The manual

adjustment is performed with the

drums removed, using the tool and the

procedure detailed below.

When adjusting the rear brake

shoes,
check the parking brake cables

for proper adjustment. Make sure that

the equalizer operates freely.
To adjust the brake shoes:

1.
Use Rotunda Tool HRE 8650,

(Fig. 11) to determine the inside diam-

eter of the drum braking surface.

2.
Reverse the tool as shown in Fig.

11 and adjust the brake shoe diameter

to fit the gauge. Hold the automatic

adjusting lever out of engagement

while rotating the adjusting screw, to

prevent burring the screw slots. Make

sure the adjusting screw rotates freely.

If necessary, lubricate the adjusting

screw threads with a thin, uniform

coating of MIC-100-A.

3.
Rotate Tool HRE 8650 around

the brake shoes to be sure of the set-

ting.

4.
Apply a small quantity of high

temperature grease to the points

where the shoes contact the backing

plate, being careful not to get the lu-

bricant on the linings.

5. Install the drums. Install Tinner-

man nuts and tighten securely.

6. Install the wheels on the drums
and tighten the nuts to specification.

7.
Complete the adjustment by

applying the brakes several times with

a minimum of 50 lbs pressure on the

pedal while backing the vehicle. After

each stop the vehicle must be moved

forward.

8. After the brake shoes have been

properly adjusted, check the operation

of the brakes by making several stops

while operating in a forward direction.

WHEEL CYLINDER REPAIR-

DRUM BRAKE

Wheel cylinders should not be di-

sassembled unless they are leaking or

unless new cups and boots are to be

installed. It is not necessary to remove

the brake cylinder from the backing

plate to disassemble, inspect, or hone

and overhaul the cylinder. Removal is

necessary only when the cylinder is

damaged or scored beyond repair.procarmanuals.com

02-02-27
Brake System

02-02-27

4.
Connect the stop light switch

wires to the connector, and install the

wires in the retaining clip.

5.
Torque the booster mounting

nuts to specifications.

LINCOLN CONTINENTAL

Removal

1.
Disconnect the battery ground

cable from the battery.

2.
It is necessary to obtain clear-

ance to remove vacuum hoses and the

electrical connector to the temperature

heat control box. Remove the two

screws retaining the relay to the fend-

er and push the relay aside. Discon-

nect the vacuum hoses and connector

at the heat control box.

3.
Working under the instrument

panel, disconnect the vacuum hoses,

wires and retaining clip from the tem-

perature heat control box. Remove the

two screws securing the temperature

control box to the dash panel.

4.
Remove the lower control hous-

ing retaining screws (6). Disconnect

the wire harnesses at the lower control

panel and place the panel aside. Re-

move the wire harness shield. Remove

the wire harness clip. Position the

wire harness aside. Remove the tem-

perature control box and position it

aside.

5.
Remove the hair-pin type retain-

er. Slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Lift the switch upward from the pin.

Slide the master cylinder push rod,

nylon washers and bushing off the

brake pedal pin.

6. Remove the pivot bolt and nut

that holds the pedal to the pedal sup-

port bracket. Remove the brake pedal

assembly from the support bracket

and remove the bushings.

7.
If required, remove the brake

pedal pad retaining nuts and remove

the brake pedal pad.

Installation

1.
If the brake pedal pad was re-

moved, position the pad on the pedal.

Install the pad retaining nuts and tor-

que them to specification.

2.
Apply SAE 10 engine oil to the

bushings and locate all the bushings in

their proper places on the pedal as-

sembly.

3.
Install the brake pedal assembly

and bushings to the support bracket,

and then install the pivot bolt through
the support bracket and pedal assem-

bly. Install the pivot bolt nut and tor-

que it to specification.

4.
Install the inner nylon washer,the

master cylinder push rod link, and the

bushing on the brake pedal pin. Posi-

tion the switch so that it straddles the

push rod link with the switch slot on

the pedal and the switch outer hole

just clearing the pin. Install the outer

nylon washer as shown in Fig. 33. In-

stall the hair-pin type retainer on the

brake pedal pin.

5.
Connect the stop light switch

wires to the connector, and install the

wires in the retaining clip.

6. Position the wire harness and

clip on the temperature control box

and install the retaining screw. Posi-

tion the temperature control box to

the dash panel and install the two re-

taining bolts.

7.
Connect the vacuum lines and

the electrical connector to the control

box. Position the wire harness to the

control box and install the retaining

clip.

8. Position the wire harness shield

and install two retaining bolts.

9. Connect the wire harnesses to

the lower control panel and install the

retaining screws.

10.
Working within the engine

compartment, connect the wire con-

nector to the temperature heat control

box.

11.
Position the relay to the fender

apron and install the retaining bolts.

12.
Connect the ground cable to the

battery.

13.
Check the brakes and light

switch for proper operation. Close the

hood.

PARKING BRAKE CONTROL

ASSEMBLY

FORD, MERCURY

AND METEOR

Removal

Refer to Fig. 34.

1.
Make sure the parking brake is

fully released.

2.
Remove all tension from the rear

cables by backing off the adjusting nut

from the equalizer.

3.
Remove the roll pin that secures

the release knob to the cable and re-

move the knob.

4.
Remove the nut that secures the

release cable to the instrument panel
and remove the cable from the rear of

the instrument panel.

5.
Remove the two nuts attaching

the control assembly to the dash

panel.

6. Remove the cap screw attaching

the control assembly to the cowl side

bracket.

7.
Disconnect the hose to the park-

ing brake vacuum unit, if so equipped.

8. Remove the front cable assembly

retainer clip from the cable assembly

and disconnect the cable ball from the

control clevis.

9. Remove the control assembly

from the vehicle.

Installation

1.
Position the control assembly in

the vehicle.

2.
Fit the cable assembly through

its mounting hole and install the re-

taining clip. Connect the cable ball to

the control clevis.

3.
Connect the vacuum hose to the

parking brake unit, if so equipped.

4.
Install the attaching cap screw to

the cowl side bracket. Do not tighten.

5.
Install the two control assemb-

ly-to-dash panel nuts. Tighten the nuts

and the cap screw to specifications.

6. Insert the release cable into the

instrument panel and install the re-

taining nut.

7.
Install the release knob on the

cable with the roll pin.

8. Check the operation of the park-

ing brake. Adjust the parking brake

as required.

FAIRLANE, MONTEGO

AND FALCON

Removal

Refer to Fig. 35.

1.
Make sure the parking brake is

completely released.

2.
Remove all tension from the rear

cables by backing off the jam nut and

adjusting nut from the equalizer.

3.
Working inside the vehicle, re-

move the four bolts and one nut re-

taining the left air vent and cable as-

sembly to the dash and instrument

panels. Remove the vent assembly.

4.
Remove the parking brake front

cable ball retaining clip from the clev-

is.

5.
Disconnect the cable ball from

the notch in the brake clevis.

6. Remove the three screws that at-

tach the control assembly to the left

cowl inner side panel.procarmanuals.com

03-05-05
Steering Columns And Linkage

03-05-05

TILT-AWAY STEERING

COLUMN REPAIRS

VACUUM RELEASE VALVE-

COUGAR AND MUSTANG

Removal

1.
Working from the underside of

the instrument panel disconnect the

hose from the valve.

2.
Disconnect the wire from the

connector on the valve and the con-

nector from the relay.

3.
Remove the bracket-

to-instrument panel attaching bolt and

let the bracket swing down.

4.
Remove the two screws that se-

cure the valve to the mounting bracket

and remove the valve.

Installation

1.
Secure the valve to the mounting

bracket with the two attaching screws.

2.
Position the bracket to the in-

strument panel and install the attach-

ing bolt.

3.
Connect the wire to the terminal

on the valve.

4.
Connect the hose from the vacu-

um motor to the horizontal connector

on the valve and the hose from the

reservoir to the vertical connector.

VACUUM RELEASE VALVE—

THUNDERBIRD

Removal

1.
Remove the lower finish panel.

2.
Disconnect the vacuum hose

from the vacuum release valve.

3.
Disconnect the vacuum release

valve electrical leads at the connector.

4.
Loosen the two attaching screws

holding the bracket to the dash. Lift

up the bracket to clear the screws and

swing it down below the panel.

5.
Remove the screws attaching the

valve to the panel and remove the

valve.

Installation

1.
Position the vacuum release

valve on the bracket.

2.
Install the two attaching screws

and swing the bracket up and over the

screws. Tighten the screws.

3.
Connect the electrical leads to

the wiring harness.
4.
Connect the hose from the vacu-

um dash panel junction block to the

connector on the vacuum release valve

that points downward and forward.

Connect the hose from the vacuum

motor to the other connector on the

release valve.

5.
Install the lower finish panel.

VACUUM MOTOR-

COUGAR AND MUSTANG

Removal

1.
Working from the underside of

the instrument panel, disconnect the

hose to the valve and the wires to the

relay and valve.

2.
Remove the bracket-

to-instrument panel attaching bolt and

swing the bracket downward.

3.
Remove the clevis pin that se-

cures the cable to the vacuum motor

rod.

4.
Disconnect the starter safety

switch wire at the connector.

5.
Remove the two motor-

to-bracket attaching screws and re-

move the motor, disconnecting the

hose to the solenoid.

Installation

1.
Position the motor on the
mounting bracket and the attaching

screws.

2.
Connect the control cable to the

vacuum motor rod with the clevis pin.

3.
Position the bracket to the in-

strument panel and install the attach-

ing bolt. Make all electrical and vacu-

um connections.

4.
Readjust the cable bracket to as-

sure full engagement of the locking

pawl when in driving position.

5.
Connect the hose to the vacuum

motor.

VACUUM MOTOR—

THUNDERBIRD

Removal

1.
Remove the lower finish panel.

2.
Disconnect the vacuum hose

from the solenoid valve. Disconnect

the electrical lead.

3.
Loosen the screws that attach

the bracket to the dash and lift the

bracket up; then, swing it down.

4.
Remove the clevis pin holding

the motor to the cable.

5.
Remove the two attaching

screws, then lift the motor from the

bracket.

C-CLAMP

PIVOT PIN

G 1462-A

FIG. 6—Installing Pivot Pinsprocarmanuals.com

03-05-08
Steering Columns And Linkage

03-05-08

tube.
In some instances the column

will shift into proper alignment when

the toe plate attaching nuts are loos-

ened. (Alignment is acceptable if a

.010 inch feeler blade can be passed

freely, completely around the area be-

tween the outer diameter of the steer-

ing shaft and the shift tube.) if the

misalignment condition can be attrib-

uted to this area, file or ream the dash

panel holes for greater clearance. If

the alignment is maintained after the

toe plate nuts and toe plate to column

clamp bolt and nut are torqued to the

8-12 ft-lb specification, no further ad-

justment is necessary.

4.
Remove instrument panel lower

trim panel. Vehicles equipped with a

combination radio stereo tape player

will require removal of the radio and

tape player assembly in order to gain

access to the upper R.H. steering col-

umn support bracket bolt.

5.
Loosen the seven bolts at the

steering column support bracket and

brake pedal support bracket.
6. Install a 3/16 inch diameter rod

spacer in the flex coupling to assure

proper clearance between upper and

lower steering shaft.

7.
Raise the vehicle, remove the

transmission splash shield, and visual-

ly align the column to center the

steering shaft in the column. Tighten

two toe plate attaching nuts sufficient-

ly to hold the column alignment (two

persons may be required for this oper-

ation).

8. Lower the vehicle.

9. Check the clearance between the

steering column support bracket and

the instrument panel bracket. It may

be necessary to add shims (Part Num-

ber MK-3054-A .060 inch thick, or

C3AZ-3054-A, .113 inch thick) be-

tween the support bracket and the in-

strument panel bracket to prevent

movement of the column when the

support bracket bolts are tightened.

10.
Loosen the two toe plate at-

taching nuts previously tightened. Re-

check steering column alignment. In
some instances it may be necessary to

enlarge the holes in the dash panel in

order to obtain proper column align-

ment.

11.
With the column properly al-

igned, torque the four toe plate at-

taching nuts to 4-9 ft-lbs.

12.
Torque the toe plate to steering

column clamp bolt to 3-5 ft-lbs.

13.
Recheck steering shaft to shift

tube alignment. A 0.10 inch feeler

blade should pass freely, completely

around the area between the outer di-

ameter of the steering shaft and shift-

er tube.

14.
Raise the vehicle.

15.
Adjust transmission shift link-

age.

16.
Install transmission splash

shield.

17.
Lower the vehicle.

18.
Install the radio stereo tape

player if so equipped.

19.
Install instrument panel lower

trim panel.

20.
Connect the battery.

REMOVAL AND INSTALLATION

STEERING COLUMN

FORD, MERCURY, METEOR

Removal

1.
Disconnect the battery cable

from the negative post.

2.
Disconnect the turn signal switch

wires at the connector.

3.
Disconnect the neutral start

switch and back-up light switch wires

from the switches.

4.
Disconnect the transmission con-

trol rod(s) from the lever(s) at the

lower end of the column.

5.
Remove the bolt that secures the

flex coupling to the steering gear.

6. Remove the nuts that secure the

column retainer and seal at the toe

plate (Fig. 11).

7.
Ford, Meteor: Remove the two

screws that secure the lower trim

shroud to the upper trim shroud. Re-

move the two shrouds.

Mercury: Remove the two screws

that secure the lower trim shroud to

the upper trim shroud. Remove the

top shroud Disconnect the ignition

switch light bulb. Remove the ignition

and light switch bezels and spring clip

and remove the lower shroud. Discon-
nect the light switch electrical connec-

tor block.

8. Remove the two screws that se-

cure the intermediate bracket to the

column lower bracket.

9. While supporting the steering

column, remove the two nuts that se-

cure the column lower bracket to the

instrument panel. Remove the brack-

ets.

10.
Lift the steering column and

wheel from the vehicle.

Installation

1.
Position the steering column in

the vehicle. Index the block tooth on

the steering gear shaft with the corre-

sponding slot on the flex coupling. In-

stall and tighten the flex coupling-

to-steering gear attaching bolt.

2.
Place the column upper bracket

and column lower bracket in position

on the column and install but do not

tighten the four attaching nuts.

3.
Install and tighten the two nuts

that secure the column lower bracket

to the instrument panel. Make certain

the column is properly positioned rela-

tive to the flex coupling input shaft

connection.

4.
Install and tighten the screws

that secure the intermediate bracket to

the column lower bracket.
5.
Tighten the four attaching nuts

at the upper and lower brackets and

the two nuts at the upper bracket to

instrument panel. The dial pointer (if

so equipped) should be adjusted to

coincide with the selector lever.

6. Install and tighten the nuts and

bolts that secure the column retainer

and seal at the toe plate. Make sure

the steering shaft is centered in the

column before tightening the nuts.

7.
Ford, Meteor: Install and tighten

the two screws that secure the lower

trim shroud to the upper trim shroud.

Mercury: Connect the light switch

harness block. Install the ignition and

light switch bezels. Connect the igni-

tion switch light bulb. Install the top

shroud and the two screws that secure

the lower trim shroud to the upper

shroud.

8. Connect the transmission control

rod(s) to the lever(s) at the lower end

of the column.

9. Connect the neutral start switch

and back-up light switch to their re-

spective terminals.

10.
Connect the turn signal switch

wires.

11.
Connect the negative battery

cable to the battery.

12.
Check the operation of the

steering tilt mechanism if so equipped

and the switches.procarmanuals.com

03-07-06
Ford Design Non-Integral Power Steering System

03-07-06

VALVE HOUSING

VALVE SPOOL

G
1659-
A

FIG. 70—Inserting Valve Spool

13.
Pick up the housing, and slide

the spool back and forth in the hous-

ing to check for free movement.

14.
Place the valve sleeve on the

housing so that the ball stud is on the

same side of the housing as the ports

for the two power cylinder lines. In-

stall the two bolts in the sleeve, and

torque them to specifications.

15.
Place the adapter on the cen-

tering spring end of the housing, and

install the bushing, washers, spacers,

and centering spring on the valve

spool bolt.

16.
Compress the centering spring,

and install the nut on the bolt. Tight-

en the nut snug (90-100 in-lbs); then

loosen it not more than 1/4 turn (Fig.

11).
Make sure that the nut turns (90

degrees) on the threads of bolt. Exces-

sive tightening of the nut may break

the stop pin at the travel regulator

stop.

TIGHTEN NUT SNUG

(90-100 IN -LBS) THEN

LOOSEN % TURN ON

THREADS OF BOLT

ADJUSTING

NUT

CENTERING SPRING

ADAPTER

G 1034 -C

FIG. 11—Adjusting Centering

Spring

17.
Move the ball stud back and

forth in the sleeve slot to check the

spool for free movement. See Part

3-13 for the specified travel. Apply
COAZ-19553-A (silicone) grease at

the sealing areas.

18.
Lubricate the two cap attaching

bolts.
Install the centering spring cap

on the valve housing, and torque the

two cap bolts to specification.

19.
Install the nut on the ball stud

so that the valve can be positioned in

a vise as shown in Fig. 12. Then push

forward on the cap end of the valve to

check the valve spool for free move-

ment.

20.
Turn the valve around in the

vise,
and push forward on the sleeve

end to check the spool for free move-

ment.

PUSH FORWARD TO CHECK

VALVE SPOOL MOVEMENT

G 1660-A

FIG. 12—Inspecting Valve Spool

Movement

POWER CYLINDER SEAL

REMOVAL

1.
Clamp the power cylinder in a

vise,
and remove the snap ring from

the end of the cylinder. Be careful not

to distort or crack the cylinder in the

vise.

2.
Pull the piston rod out all the

way to remove the scraper, bushing,

and seals. If the seals cannot be re-
moved in this manner, remove them

from the cylinder with a sharp pick.

Take care, when using a pick, not to

damage the shaft or seal seat.

INSTALLATION

When replacing the power cylinder

seals,
install all of the parts supplied

in the repair kit for the cylinder being

repaired.

1.
Coat the new seals with lubricant

COAZ-19553-A and place the parts

(Fig. 13) on the piston rod which has

been coated with the same grease.

2.
Push the rod in all the way, and

install the parts in the cylinder with a

deep socket slightly smaller than the

cylinder opening (Fig. 14).

15/16"
O.D. X6" STEEL

ELECTRICAL CONDUIT

POWER

CYLINDER

G 1662-A

FIG. 14—Installing Power

Cylinder Seals

POWER STEERING PUMP

RESERVOIR REPLACEMENT

Refer to Group 3-10, Section 3 for

detailed instructions.

INSERT

RUBBER WIPER

SCRAPER

SEATS'

FIG. 73—Power Cylinder
SNAP RING

G 1661-Aprocarmanuals.com