bulb FORD MUSTANG 1969 Volume One Chassis

03-05-08
Steering Columns And Linkage

03-05-08

tube.
In some instances the column

will shift into proper alignment when

the toe plate attaching nuts are loos-

ened. (Alignment is acceptable if a

.010 inch feeler blade can be passed

freely, completely around the area be-

tween the outer diameter of the steer-

ing shaft and the shift tube.) if the

misalignment condition can be attrib-

uted to this area, file or ream the dash

panel holes for greater clearance. If

the alignment is maintained after the

toe plate nuts and toe plate to column

clamp bolt and nut are torqued to the

8-12 ft-lb specification, no further ad-

justment is necessary.

4.
Remove instrument panel lower

trim panel. Vehicles equipped with a

combination radio stereo tape player

will require removal of the radio and

tape player assembly in order to gain

access to the upper R.H. steering col-

umn support bracket bolt.

5.
Loosen the seven bolts at the

steering column support bracket and

brake pedal support bracket.
6. Install a 3/16 inch diameter rod

spacer in the flex coupling to assure

proper clearance between upper and

lower steering shaft.

7.
Raise the vehicle, remove the

transmission splash shield, and visual-

ly align the column to center the

steering shaft in the column. Tighten

two toe plate attaching nuts sufficient-

ly to hold the column alignment (two

persons may be required for this oper-

ation).

8. Lower the vehicle.

9. Check the clearance between the

steering column support bracket and

the instrument panel bracket. It may

be necessary to add shims (Part Num-

ber MK-3054-A .060 inch thick, or

C3AZ-3054-A, .113 inch thick) be-

tween the support bracket and the in-

strument panel bracket to prevent

movement of the column when the

support bracket bolts are tightened.

10.
Loosen the two toe plate at-

taching nuts previously tightened. Re-

check steering column alignment. In
some instances it may be necessary to

enlarge the holes in the dash panel in

order to obtain proper column align-

ment.

11.
With the column properly al-

igned, torque the four toe plate at-

taching nuts to 4-9 ft-lbs.

12.
Torque the toe plate to steering

column clamp bolt to 3-5 ft-lbs.

13.
Recheck steering shaft to shift

tube alignment. A 0.10 inch feeler

blade should pass freely, completely

around the area between the outer di-

ameter of the steering shaft and shift-

er tube.

14.
Raise the vehicle.

15.
Adjust transmission shift link-

age.

16.
Install transmission splash

shield.

17.
Lower the vehicle.

18.
Install the radio stereo tape

player if so equipped.

19.
Install instrument panel lower

trim panel.

20.
Connect the battery.

REMOVAL AND INSTALLATION

STEERING COLUMN

FORD, MERCURY, METEOR

Removal

1.
Disconnect the battery cable

from the negative post.

2.
Disconnect the turn signal switch

wires at the connector.

3.
Disconnect the neutral start

switch and back-up light switch wires

from the switches.

4.
Disconnect the transmission con-

trol rod(s) from the lever(s) at the

lower end of the column.

5.
Remove the bolt that secures the

flex coupling to the steering gear.

6. Remove the nuts that secure the

column retainer and seal at the toe

plate (Fig. 11).

7.
Ford, Meteor: Remove the two

screws that secure the lower trim

shroud to the upper trim shroud. Re-

move the two shrouds.

Mercury: Remove the two screws

that secure the lower trim shroud to

the upper trim shroud. Remove the

top shroud Disconnect the ignition

switch light bulb. Remove the ignition

and light switch bezels and spring clip

and remove the lower shroud. Discon-
nect the light switch electrical connec-

tor block.

8. Remove the two screws that se-

cure the intermediate bracket to the

column lower bracket.

9. While supporting the steering

column, remove the two nuts that se-

cure the column lower bracket to the

instrument panel. Remove the brack-

ets.

10.
Lift the steering column and

wheel from the vehicle.

Installation

1.
Position the steering column in

the vehicle. Index the block tooth on

the steering gear shaft with the corre-

sponding slot on the flex coupling. In-

stall and tighten the flex coupling-

to-steering gear attaching bolt.

2.
Place the column upper bracket

and column lower bracket in position

on the column and install but do not

tighten the four attaching nuts.

3.
Install and tighten the two nuts

that secure the column lower bracket

to the instrument panel. Make certain

the column is properly positioned rela-

tive to the flex coupling input shaft

connection.

4.
Install and tighten the screws

that secure the intermediate bracket to

the column lower bracket.
5.
Tighten the four attaching nuts

at the upper and lower brackets and

the two nuts at the upper bracket to

instrument panel. The dial pointer (if

so equipped) should be adjusted to

coincide with the selector lever.

6. Install and tighten the nuts and

bolts that secure the column retainer

and seal at the toe plate. Make sure

the steering shaft is centered in the

column before tightening the nuts.

7.
Ford, Meteor: Install and tighten

the two screws that secure the lower

trim shroud to the upper trim shroud.

Mercury: Connect the light switch

harness block. Install the ignition and

light switch bezels. Connect the igni-

tion switch light bulb. Install the top

shroud and the two screws that secure

the lower trim shroud to the upper

shroud.

8. Connect the transmission control

rod(s) to the lever(s) at the lower end

of the column.

9. Connect the neutral start switch

and back-up light switch to their re-

spective terminals.

10.
Connect the turn signal switch

wires.

11.
Connect the negative battery

cable to the battery.

12.
Check the operation of the

steering tilt mechanism if so equipped

and the switches.procarmanuals.com

07-02-08
C4 Automatic Transmission

07-02-08

8. Install the outer downshift lever

and attaching nut, and torque the nut

to specification. Install the downshift

linkage rod to the downshift lever.

9. Install the switch wires. Connect

the wire multiple connector. Check

the operation of the switch in each de-

tent position. The engine should start

only with the transmission selector

lever in N (neutral) and P (park).

SELECTOR LEVER

REPLACEMENT—CONSOLE SHIFT

FORD-METEOR

1.
Raise the vehicle and disconnect

the link assembly from the selector

lever arm (Fig. 6).

2.
Lower the vehicle. Remove the

four screws and plates securing the se-

lector lever handle to the lever. Re-

move the handle and detent control.

3.
Remove the two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

4.
Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

quadrant.

5.
Remove the four bolts that at-

tach the selector lever housing to the

floor pan and remove the selector

lever and housing.

6. Position the new selector lever

and housing assembly on the floor pan

and install the attaching bolts.

7.
Connect the bulb socket to the

quadrant and the neutral start switch

wires to the plug connector.

8. Raise the vehicle and secure the

link assembly to the selector lever arm

with the bushing, insulator, flat wash-

er and cotter pin (Fig. 6). Lower the

vehicle.

9. Place the console top panel on

the console and install the retaining

screws.

10.
Position the selector lever de-

tr*rtt control and handle on the selector

lever and secure with the four plates

and attaching screws.

FAIRLANE-MONTEGO

1.
Raise the vehicle on a hoist or

jack stands.

2.
Remove the retainer that secures

the manual linkage rod to the lower

end of the manual lever (Fig. 7).

3.
Remove the flat washer and two

insulator washers and disconnect the

rod from the arm.

4.
Working from inside of the vehi-

cle,
remove the selector lever handle

attaching screw. Lift the handle off

the selector lever.
DETENT PAWL

LOCK NUT

DETENT PAWL

ADJUSTMENT SCREW

DETENT PLATE

D 1644-A

FIG. 72—Typical Selector Lever Detent Pawl Adjustment

5.
Remove the console trim panel

from the top of the console. Remove

the console retaining screws and re-

move the console.

6. Remove the cover and dial indi-

cator as an assembly.

7.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

8. Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

selector lever housing.

9. Remove the three bolts that se-

cure the selector lever control housing

to the console. Lift the selector lever

housing from the console.

10.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

11.
Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-31bs.

12.
Install the selector lever handle.

13.
Position the selector lever as

shown in Figure 12. With a feeler

gauge, check the clearance between

the detent pawl and plate. The clear-

ance should be 0.005 to 0.010 inch. If

necessary adjust the height of the de-

tent pawl as shown in Figure 12.

14.
Remove the handle from the se-

lector lever.

15.
Position the selector lever hous-

ing in the console and install the three

attaching bolts. Do not tighten the at-

taching bolts at this time.

16.
Connect the bulb socket to the

selector lever housing and the neutral

start switch wires to the plug connec-

tor.

17.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

18.
Install the cover and dial indi-

cator.
19.
Place the console in position

and install the retaining bolts. Tighten

the selector lever housing attaching

bolts.

20.
Position the console trim panel

and secure it with the attaching

screws.

21.
Install the handle and the but-

ton on the selector lever. Secure the

handle with the set screw.

22.
Secure the manual linkage rod

to the arm with two insulating wash-

ers,
a flat washer and a retainer (Fig.

7).

23.
Adjust the linkage as required.

J r the vehicle.

MUSTANG

1.
Raise the vehicle and remove the

manual lever control rod attaching nut

(Fig. 8).

2.
Lower the vehicle, remove the se-

lector lever handle attaching screw.

3.
Remove the dial housing attach-

ing screws and the housing.

4.
Remove the two pointer back-up

shield attaching screws and remove

the shield.

5.
Disconnect the dial indicator

light.

6. Remove the selector housing and

lever assembly attaching bolts. Re-

move the selector lever and housing.

7.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

8. Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

9. Install the selector lever handle.

10.
Position the selector lever as

shown in Figure 12. With a feeler

gauge check the clearance between the

detent pawl and plate. The clearance

should be 0.005 to 0.010 inch. If nec-

essary adjust the height of the detent

pawl as shown in Figure 12.procarmanuals.com

07-03-08

FAAX Transmission
07-03-08

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.

MUSTANG-COUGAR

1.
Place the transmission selector

lever in the N (Neutral) position.

2.
Raise the vehicle and remove the

manual lever control rod attaching nut

(Fig. 7).

3.
Lower the vehicle and remove

the selector lever handle attaching

screw and the handle.

4.
Remove the dial housing attach-

ing screws and the housing.

5.
Disconnect the dial indicator

light.

6. Disconnect the neutral start

switch and dial indicator light wires

from their connectors at the dash

panel.

7.
Remove the four selector housing

and lever assembly attaching bolts.

Remove the selector lever and housing

assembly.

8. Remove the two pointer back-up

shield attaching screws and remove

the shield.

9. Remove the two screws securing

the neutral start switch to the selector

lever housing. Push the neutral start

switch harness plug inward and re-

move the switch and harness assembly

(Fig. 9).

10.
Before installing the new

switch, hold it with the wires facing

downward and move the actuator

lever all the way to the left. Then, re-

turn the actuator lever to the neutral

position as shown in Figure 9.

11.
Position the harness and neutral

switch assembly in the selector lever

housing. Secure with the two attach-

ing screws.

12.
Install the pointer back-up

shield on the housing and lever assem-

bly.

13.
Position the selector lever and

housing assembly on the console and

install the attaching bolts.

14.
Connect the dial indicator light.

15.
Connect the neutral start switch

and dial indicator light wires to their

respective connectors at the dash

panel.

16.
Install the dial housing on the

selector lever housing assembly.

17.
Install the selector lever handle.

18.
Raise the vehicle and secure the

manual lever control rod to the selec-

tor lever arm.

19.
Lower the vehicle.

20.
Place the selector lever in the

park position and check the operation

of the switch.
DETENT PAWL

LOCK
NUT

DETENT PAWL

ADJUSTMENT SCREW

DETENT PLATE

D 1644-A

FIG.
10—Typical Selector Lever Detent Pawl Adjustment

SELECTOR LEVER

REPLACEMENT—CONSOLE

SHIFT—FAIRLANE

AND
MONTEGO

1.
Raise the vehicle on a hoist or

jack stands.

2.
Remove the retainer that secures

the manual linkage rod to the lower

end of the manual lever (Fig. 6).

3.
Remove the flat washer and two

insulator washers and disconnect the

rod from the arm.

4.
Working from inside of the vehi-

cle,
remove the selector lever handle

attaching screw. Lift the handle off

the selector lever.

5.
Remove the console trim panel

from the top of the console. Remove

the console retaining screws and re-

move the console.

6. Remove the cover and dial indi-

cator as an assembly.

7.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

8. Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

selector lever housing.

9. Remove the three bolts that se^

cure the selector lever control housing

to the console. Lift the selector lever

housing from the console.

10.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

11.
Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

12.
Install the selector lever handle.

13.
Position the selector lever as

shown in Figure 10. With a feeler

gauge,
check the clearance between
the detent pawl and plate. The clear-

ance should be 0.005 to 0.010 inch. If

necessary adjust the height of the de-

tent pawl as shown in Figure 10.

14.
Remove the handle from the se-

lector lever.

15.
Position the selector lever hous-

ing in the console and install the three

attaching bolts. Do not tighten the at-

taching bolts at this time.

16.
Connect the bulb socket to the

selector lever housing and the neutral

start switch wires to the plug connec-

tor.

17.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

18.
Install the cover and dial indi-

cator.

19.
Place the console in position

and install the retaining bolts. Tighten

the selector lever housing attaching

bolts.

20.
Position the console trim panel

and secure it with the attaching

screws.

21.
Install the handle and the but-

ton on the selector lever. Secure the

handle with the set screw.

22.
Secure the manual linkage rod

to the arm with two insulating wash-

ers,
a flat washer and a retainer (Fig.

6).

23.
Adjust the linkage as required.

Lower the vehicle.

MUSTANG-COUGAR

1.
Raise the vehicle and remove the

manual lever control rod attaching nut

(Fig. 7).

2.
Lower the vehicle, remove the se-

lector lever handle attaching screw.

3.
Remove the dial housing attach-

ing screws and the housing.procarmanuals.com

07-04-09
C-6 Automatic Transmission
07-04-09

MUSTANG AND COUGAR

1.
With the manual lever properly

adjusted, loosen the two switch attach-

ing bolts (Fig. 13).

2.
With the transmission manual

lever in neutral, rotate the switch and

insert the gauge pin (No. 43 drill

shank end) into the gauge pin holes of

the switch. The gauge pin has to be

inserted to a full 31/64 inch into the

three holes of the switch (Fig. 13).

3.
Torque the two switch attaching

bolts to specification. Remove the

gauge pin from the switch.

4.
Check the operation of the

switch. The engine should start only

with the transmission selector lever in

Neutral and Park.

NEUTRAL START SWITCH

REPLACEMENT—CONSOLE

SHIFT

On vehicles equipped with a

column-mounted neutral start switch,

refer to Part 7-1, Section 2, for the

replacement procedures.

FORD, MERCURY

AND METEOR

1.
Remove the four screws and

plates securing the selector lever

handle to the lever. Remove the

handle and detent control.

2.
Remove the two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

3.
Remove the two screws securing

the dial indicator assembly to the se-

lector lever housing and remove the

indicator assembly.

4.
Disconnect the neutral start

switch wires at the plug connector.

Remove the wires from under the re-

taining clip.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing and remove the switch

(Fig. 11).

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
Adjust the neutral start switch as

outlined under the Neutral Start

Switch Adjustment procedures in this

section.

8. Connect the neutral start switch

Wires to the plug connector. Position

the wires in the retaining clip and

close the clip.

9. Place the console top panel on

the console and install the retaining

screws.
NEUTRAL START

SWITCH

D1459-A

FIG. 73—Neutral Start Switch

Adjustment—Console Shift—

Mustang and Cougar

10.
Position the selector lever de-

tent control and handle on the selector

lever and secure with the four plates

and attaching screws.

FAIRLANE AND MONTEGO

1.
Remove the selector lever handle

from the lever.

2.
Remove the trim panel from the

top of the console.

3.
Remove the cover and dial indi-

cator as an assembly.

4.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing. Disconnect the neutral

start switch wires at the plug connec-

tor and remove the switch.

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
With the selector lever in neu-

tral,
move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 12).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

11.
Connect the neutral start switch

wires to the plug connector and check

for starting in the park position.
12.
Position the selector lever re-

tainer to the selector lever housing.

Install the attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.

MUSTANG AND COUGAR

1.
Remove the downshift linkage

rod from the transmission downshift

lever.

2.
Apply penetrating oil to the

downshift lever shaft and nut. Remove

the transmission downshift outer lever

retaining nut and lever (Fig. 13).

3.
Remove the two neutral start

switch attaching bolts.

4.
Disconnect the multiple wire

connector. Remove the neutral switch

from the transmission.

5.
Install the neutral start switch on

the transmission. Install the two at-

taching bolts.

6. With the transmission manual

lever in neutral, rotate the switch and

install gauge pin (No. 43 drill) into

the gauge pin hole (Fig. 13).

7.
Tighten the switch attaching

bolts to specification and remove the

gauge pin.

8. Install the outer downshift lever

and attaching nut, and torque the nut

to specification. Install the downshift

linkage rod to the downshift lever.

9. Install the switch wires. Connect

the wire multiple connector. Check

the operation of the switch in each de-

tent position. The engine should start

only with the transmission selector

lever in N (neutral) and P (park).

SELECTOR LEVER

REPLACEMENT-

CONSOLE SHIFT

FORD, MERCURY

AND METEOR

1.
Raise the vehicle and disconnect

the link assembly from the selector

lever arm (Fig. 8).

2.
Lower the vehicle. Remove the

four screws and plates securing the se-

lector lever handle to the lever. Re-

move the handle and detent control.

3.
Remove the two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

4.
Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

quadrant.procarmanuals.com

07-04-10
C-6 Automatic Transmission

07-04-10

5.
Remove the four bolts that at-

tach the selector lever housing to the

floor pan and remove the selector

lever and housing.

6. Position the new selector lever

and housing assembly on the floor pan

and install the attaching bolts.

7.
Connect the bulb socket to the

quadrant and the neutral start switch

wires to the plug connector.

8. Raise the vehicle and secure the

link assembly to the selector lever arm

with the bushing, insulator, flat wash-

er and cotter pin (Fig. 8). Lower the

vehicle.

9. Place the console top panel on

the console and install the retaining

screws.

10.
Position the selector lever de-

tent control and handle on the selector

lever and secure with the four plates

and attaching screws.

FAIRLANE AND MONTEGO

1.
Raise the vehicle on a hoist or

jack stands.

2.
Remove the retainer that secures

the manual linkage rod to the lower

end of the manual lever (Fig. 9).

3.
Remove the flat washer and two

insulator washers and disconnect the

rod from the arm.

4.
Working from inside of the vehi-

cle,
remove the selector lever handle

attaching screw. Lift the handle off

the selector lever.

5.
Remove the console trim panel

from the top of the console. Remove

the console retaining screws and re-

move the console.

6. Remove the cover and dial indi-

cator as an assembly.

7.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

8. Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

selector lever housing.

9. Remove the three bolts that se-

cure the selector lever control housing

to the console. Lift the selector lever

housing from the console.

10.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

11.
Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

12.
Install the selector lever handle.

13.
Position the selector lever as

shown in Figure 14. With a feeler

gauge, check the clearance between
DETENT
PAWL

LOCK
NUT

DETENT
PAWL

ADJUSTMENT
SCREW

DETENT
PLATE

D
1644-A

FIG. 14—Typical Selector Lever Detent Pawl Adjustment

the detent pawl and plate. The clear-

ance should be 0.005 to 0.010 inch. If

necessary adjust the height of the de-

tent pawl as shown in Figure 14.

14.
Remove the handle from the se-

lector lever.

15.
Position the selector lever hous-

ing in the console and install the three

attaching bolts. Do not tighten the at-

taching bolts at this time.

16.
Connect the bulb socket to the

selector lever housing and the neutral

start switch wires to the plug connec-

tor.

17.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

18.
Install the cover and dial indi-

cator.

19.
Place the console in position

and install the retaining bolts. Tighten

the selector lever housing attaching

bolts.

20.
Position the console trim panel

and secure it with the attaching

screws.

21.
Install the handle and the but-

ton on the selector lever. Secure the

handle with the set screw.

22.
Secure the manual linkage rod

to the arm with two insulating wash-

ers,
a flat washer and a retainer (Fig.

9).

23.
Adjust the linkage as required.

Lower the vehicle.

MUSTANG AND COUGAR

1.
Raise the vehicle and remove the

manual lever control rod attaching nut

(Fig. 10).

2.
Lower the vehicle, remove the se-

lector lever handle attaching screw.
3.
Remove the dial housing attach-

ing screws and the housing.

4.
Remove the pointer back-up

shield attaching screws and remove

the shield.

5.
Disconnect the dial indicator

light.

6. Remove the selector housing and

lever assembly attaching bolts. Re-

move the selector lever and housing.

7.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

8. Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

9. Install the selector lever handle.

10.
Position the selector lever as

shown in Figure 14. With a feeler

gauge check the clearance between the

detent pawl and plate. The clearance

should be 0.005 to 0.010 inch. If nec-

essary adjust the height of the detent

pawl as shown in Figure 14.

11.
Remove the handle from the se-

lector lever.

12.
Install the selector housing and

lever assembly as shown in Figure 10.

Torque the attaching bolts 4-6 ft-lbs.

13.
Connect the dial indicator light.

14.
Install the pointer back-up

shield on the housing and lever assem-

bly.

15.
Install the dial housing and

tighten the attaching screws.

16.
Install the selector lever handle

and tighten the attaching screw.

17.
Position the selector lever in the

D position.

18.
Raise the vehicle. Install the

transmission manual lever rod to the

selector lever. Adjust the manual link-

age.

19.
Lower the vehicle and check the

transmission operation in each selec-

tor lever detent position.procarmanuals.com