lane assist FORD MUSTANG 1969 Volume One Chassis

02-02-22
Brake System

02-02-22

BRAKE VACUUM BOOSTER -2005

AUTOMATIC I

TRANSMISSION

HAIR PIN RETAINER

330699-S2

SPACER

STOP LIGHT SWITCH-13480

STANDARD

TRANSMISSION
BUSHING
BUSHING

PUSH ROD

BRAKE PEDAL ASSEMBLY
CLUTCH

PEDAL

ASSEMBLY

H 1557-C

FIG. 30—Master Cylinder Installation—Power Brake-

Fairlane, Montego and Falcon

ASSIST

SPRING BRACKET CLUTCH ASSIST

\ SPRING

BRAKE PEDAL

SHAFT

CLUTCH

PEDAL

CLUTCH PEDAL

TO EQUALIZER ROD

HI643-
A

FIG. 31—Master Cylinder Installation-

Power Brake—Mustang and Cougar
6. Bleed the dual-master cylinder

and the primary and secondary brake

systems. Centralize the pressure dif-

ferential valve. Refer to H>draulic

System Bleeding and Centralizing of

the Differential Valve, Part 2-1, Sec-

tion 2 for the proper procedure.

7.
Operate the brakes several times,

then check for external hydraulic

leaks.

PRESSURE DIFFERENTIAL

VALVE AND PROPORTIONING

VALVE ASSEMBLY

REMOVAL

1.
Disconnect the brake warning

light wire from the pressure differen-

tial valve assembly switch (Figs. 17

thru 21). To prevent damage to the

brake warning switch wire connector,

expand the plastic lugs to allow re-

moval of the shellwire connector from

the switch body.

2.
Loosen the tube nuts connecting

the primary and secondary inlet and

outlet tubes at the pressure differential

valve assembly and remove the tubes.

3.
Remove the screw or screws re-

taining the pressure differential valve

assembly to the chassis and remove

the valve assembly.

4.
On disc brake equipped vehicles,

place the pressure differential valve

assembly and mounting bracket in a

vise.
Loosen the proportioning valve

tube nuts at the differential valve and

at the proportioning valve. Remove

the proportioning valve from the

mounting bracket.

5.
If the differential valve is to be

replaced, remove the brake warning

lamp switch and install the switch in

the new differential valve. The pres-

sure differential valve assembly, the

brake warning lamp switch, and the

proportioning valve are separate units

and each is serviced as a separate as-

sembly only.

INSTALLATION

1.
On disc brake equipped vehicles,

connect the proportioning valve inlet

and outlet tubes to the proportioning

valve and differential valve bodies.

Tighten the tube nuts to specification.

2.
Mount the pressure differential

valve assembly on the chassis and in-

stall the attaching screw or screws.

3.
Connect the primary and second-

ary inlet and outlet tubes to the pres-

sure differential valve assembly and

tighten the tube nuts to specifications.procarmanuals.com

02-02-25
Brake System

02-02-25

clearing the pin. Slide the switch com-

pletely onto the pin, and install the

nylon washer as shown in Figs. 29

thru 33. Be careful not to bend or de-

form the switch. Secure these parts to

the pin with the hairpin retainer. Con-

nect the stop light switch wires to the

connector, and install the wires in the

retaining clip.

BRAKE PEDAL

FORD, MERCURY

AND METEOR

Removal

1.
Disconnect the stop light switch

wires at the connector.

2.
Remove the hairpin retainer.

Slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin,

and then lift the switch straight up-

ward from the pin. Be careful not to

damage the switch during removal.

Slide the master cylinder or booster

push rod and the nylon washers and

bushing off the brake pedal pin (Figs.

26 and 29).

3.
Remove the hairpin type retainer

and washer from the brake pedal

shaft, then remove the shaft, the brake

pedal and the bushings from the pedal

support bracket.

Installation

1.
Apply a coating of SAE 10 En-

gine oil to the bushings and locate

bushings in their proper places on the

pedal assembly and pedal support

bracket (Figs. 26 and 29).

2.
Position the brake pedal assem-

bly to the support bracket, then install

the pedal shaft through the support

bracket and brake pedal assembly. In-

stall the retainer.

3.
Install the inner nylon washer,

the master cylinder or booster push

rod, and the bushing on the brake

pedal pin. Position the switch so that

it straddles the push rod with the

switch slot on the pedal pin and the

switch outer hole just clearing the pin.

Slide the switch completely onto the

pin, and install the nylon washer as

shown in Figs. 26 and 29. Be careful

not to bend or deform the switch. Se-

cure these parts to the pin with the

hairpin retainer.

4.
Connect the stop light switch

wires to the connector, and install the

wires in the retaining clip.
5.
Check the Brake Pedal Free

Height and Travel Measurements,

Part 2-1, Section 1.

FAIRLANE, MONTEGO AND

FALCON—MANUAL-SHIFT

TRANSMISSION

Removal

1.
Remove the clutch pedal assist

spring.

2.
Disconnect the clutch pedal-

to-equalizer rod at the clutch pedal by

removing the retainer and bushing.

3.
Disconnect the stop light switch

wires at the connector.

4.
Remove the switch retainer, and

slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Then lower the switch away from the

pin.

5. Slide the master cylinder or

booster push rod and the nylon wash-

ers and bushing off from the brake

pedal pin (Figs. 27 and 30).

6. Remove the self-locking pin and

washer from the clutch and brake

pedal shaft, then remove the clutch

pedal and shaft assembly, the brake

pedal assembly, and the bushings from

the pedal support bracket (Figs. 27

and 30).

Installation

1.
Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

bushings in their proper places on the

clutch and brake pedal assemblies.

2.
Position the brake pedal to the

support bracket, then install the clutch

pedal and shaft assembly through the

support bracket and brake pedal as-

sembly. Install the spring clip (Figs.

27 and 30).

3.
Install the clutch pedal assist

spring.

4.
Connect the clutch pedal-

to-equalizer rod to the clutch pedal

assembly with the bushing and the

spring clip retainer. Apply SAE 10

engine oil to the bushing.

5.
Install the inner nylon washer,

the master cylinder or booster push

rod, and the bushing on the brake

pedal pin. Position the switch so that

it straddles the push rod with the

switch slot on the pedal pin and the

switch outer hole just clearing the pin.

Slide the switch completely onto the

pin, and install the outer nylon washer

as shown in Figs. 27 and 30. Secure

these parts to the pin with the
self-

locking pin.
6. Connect the stop light switch

wires to the connector, and install the

wires to the retaining clip.

7.
Adjust the clutch pedal free play

(Group 5) to specification, if required.

8. Check the Brake Pedal Free

Height and Travel Measurements

(Part 2-1, Section 1).

MUSTANG AND COUGAR—

MANUAL-SHIFT

TRANSMISSION

Removal

1.
Disconnect the battery ground

cable from the battery.

2.
Remove the steering column.

Refer to Part 3-4, Section 2 for pro-

cedure.

3.
On non-power brakes, remove

the two cap screws retaining the mas-

ter cylinder to the dash panel and re-

move the two cap screws retaining the

brake pedal support bracket to the

dash panel. On power brakes remove

the two cap screws retaining the

booster to the dash panel.

4.
Working inside the vehicle, se-

cure the clutch pedal against the

bumper stop with a small C-clamp as

shown in Figs. 28 and 31.

5.
Disconnect the clutch pedal-

to-equalizer rod at the clutch pedal by

removing the retainer and bushing.

6. Disconnect the stop light switch

wires at the connector.

7.
Remove the switch retainer and

slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Then lower the switch away from the

pin.
Remove the master cylinder or

booster push rod, bushing and nylon

washer from the brake pedal pin.

8. Remove the screw retaining the

pedal support bracket to the top inner

cowl bracket (Figs. 28 and 31).

9. Remove the two sheet metal

screws retaining the pedal support

bracket to the dash panel. On power

brakes remove the nuts from the

brake booster studs.

10.
Remove the two screws retain-

ing the pedal support bracket to the

upper cowl brace and lower the pedal

support bracket away from the steer-

ing column studs.

11.
Remove the pedal support

bracket assembly from the vehicle.

12.
Position the pedal and support

bracket assembly in a vise.

13.
Remove the C-clamp to release

the clutch pedal from its bumper stop

and pivot the pedal away from the

bumper.procarmanuals.com

02-02-26
Brake System

02-02-26

14.
Remove the clutch pedal assist

spring.

15.
On non-power brakes, remove

the retainer clip from the clutch and

brake pedal shaft, then remove the

clutch pedal and shaft assembly, the

brake pedal assembly, and the bush-

ings from the pedal support bracket.

On power brakes, remove the retainer

nut from the brake pedal shaft then

remove the pedal shaft, the brake

pedal assembly and the bushings from

the pedal support bracket.

Installation

1. Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

bushings in their proper places on the

clutch and brake pedal assemblies.

2.
On non-power brakes, position

the brake pedal to the pedal support

bracket, then install the clutch pedal

and shaft assembly through the sup-

port bracket and brake pedal assem-

bly. On power brakes position the

brake pedal to the pedal support

bracket, then install the pedal shaft

and nut.

3.
Install the clutch pedal assist

spring and pivot the clutch pedal

against its bumper stop. Secure the

pedal to the stop with a small C-

clamp as shown in Figs. 28 and 31.

4.
Position the pedal support

bracket assembly to the dash panel,

and to the steering column retainer

studs.

5.
Align the pedal support bracket

holes with the holes in the dash panel

and install the two attaching sheet

metal screws. On power brakes install

the nuts on the brake booster studs.

6. Install the two cap screws at-

taching the pedal support bracket to

the upper cowl bracket.

7. Install the cap screw attaching

the pedal support bracket to the top

inner cowl bracket (Figs. 28 and 31).

8. Install the inner nylon washer,

the master cylinder push rod, and the

bushing on the brake pedal pin. Posi-

tion the stop light switch so that it

straddles the push rod with the switch

slot on the pedal pin and the switch

outer hole just clearing the pin. Slide

the switch completely onto the pin,

and install the outer nylon washer as

shown in Figs. 28 and 31. Secure

these parts to the pin with the
self-

locking retainer.

9. Connect the stop light switch

wires to the connector.

10.
Connect the clutch pedal-

to-equalizer rod to the clutch pedal

assembly with the bushing and the

spring clip retainer. Apply SAE 10
engine oil to the bushing. Remove the

C-clamp from the clutch pedal.

11.
Working from the engine side

of the dash panel, on non-power

brakes, install the two cap screws at-

taching the pedal support bracket to

the dash panel. Then install the two

screws attaching the master cylinder

to the dash panel. On power brakes

install the cap screws retaining the

brake booster to the dash panel.

12.
Install the steering column.

Refer to Part 3-4, Section 2 for pro-

cedure.

13.
Adjust the clutch pedal free

play (Group 5) to specification, if re-

quired.

14.
Check the Brake Pedal Free

Height and Travel Measurements

(Part 2-1, Section 1).

15.
Connect the ground cable to the

battery.

FAIRLANE, MONTEGO,

FALCON, MUSTANG

AND COUGAR-

AUTOMATIC TRANSMISSION

Removal

1. Disconnect the stop light switch

wires at the connector.

2.
Remove the self-locking pin and

slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Then lower the switch away from the

pin. Slide the master cylinder or

booster push rod and the nylon wash-

ers and bushing off from the brake

pedal pin (Figs. 27, 28, 30 and 31).

3.
On all vehicles except Mustang

and Cougar with power brakes, re-

move the self-locking pin and washer

from the brake pedal shaft, then re-

move the shaft, the brake pedal as-

sembly and the bushings from the

pedal support bracket. On Mustang

and Cougar vehicles with power

brakes, remove the locknut and bolt

from the pedal. Remove the pedal as-

sembly from the support bracket (Fig.

3).

Installation

1. Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

the bushings in their proper places on

the pedal assembly and pedal support

bracket (Figs. 27, 28, 30 and 31).

2.
Position the brake pedal assem-

bly to the support bracket, then install

the pedal shaft or bolt through the

support bracket and brake pedal as-

sembly. Install the retainer or locknut.
3.
Install the inner nylon washer,

the master cylinder or booster push

rod, and the bushing on the brake

pedal pin. Position the switch so that

it straddles the push rod with the

switch slot on the pedal pin, and the

switch outer hole just clearing the pin.

Slide the switch completely onto the

pin, and install the outer nylon washer

as shown in Figs. 27, 28, 30 and 31.

Secure these parts to the pin with the

self-locking pin.

4.
Connect the stop light switch

wires to the connector, and install the

wires in the retaining clip.

Check the Brake Pedal Free Height

and Travel Measurements, Part 2,

Section 1.

THUNDERBIRD
AND

CONTINENTAL MARK
III

Removal

1.
Loosen the booster mounting

nuts.

2.
Disconnect the stop light switch

wires at the connector.

3.
Remove the hairpin retainer.

Slide the stop light switch off from

the brake pedal pin just far enough

for
the
switch outer hole
to
clear
the

pin,
and then lift the switch straight

upward from the pin. Slide the master

cylinder push rod and the nylon wash-

ers and bushing off from the brake

pedal pin (Fig. 32).

4.
Remove the pivot bolt and nut

that holds the pedal to the pedal sup-

port bracket. Remove the brake pedal

assembly from the pedal support

bracket, and remove the bushings.

Installation

1. Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

the bushings in their proper places on

the pedal assembly (Fig. 32).

2.
Install the brake pedal assembly

and bushings to the support bracket,

and then install the pivot bolt through

the support bracket and brake pedal

assembly. Install the pivot bolt nut

and torque to specifications.

3.
Install the inner nylon washer,

the master cylinder push rod, and the

bushing on the brake pedal pin. Posi-

tion the switch so that it straddles the

push rod with the switch slot on the

pedal pin and the switch outer hole

just clearing the pin. Slide the switch

completely onto the pin, install the

outer nylon washer as shown in Fig.

32.
Secure these parts to the pin with

the hairpin retainer.procarmanuals.com

03-01-03
Suspension — Steering, Wheels And Tires — General Service

03-01-03

4.
Connect a tachometer, start the

engine and operate it at idle speed

until the reservoir fluid temperature

reaches 165 to 175. This temperature

must be maintained throughout the

test. Valve B may be partially closed

to create a back pressure up to 350

psi to hasten the temperature rise. The

reservoir fluid must be at the proper

level.

5.
With the engine operating at rec-

ommended idle rpm and fluid temper-

ature noted in Step 4, close the manu-

al valve B. The minimum acceptable

pressure reading is 620 psi.

6. If the pressure gauge reading is

below the minimum specification, the

pump is at fault and should be re-

paired with necessary parts.

7.
If the reading is at or above the

minimum specification, the pump flow

is normal. Open manual valve B and

proceed to the Pump Fluid Pressure

Test.

PUMP FLUID

PRESSURE TEST

1.
Keep the lines and tools con-

nected as in the Pump Flow Test.

2.
With manual valves A and B

opened fully, operate the engine at

recommended idle speed (Fig. 2).

Close manual valve A, then manual

valve B. Do not keep both valves

closed for more than 5 seconds as this

would abnormally increase the fluid

temperature and cause undue pump

and/or gear wear.

3.
With the valves fully closed, the

pressure gauge should read 1000 psi

minimum for Ford, Mercury, Meteor

or Thunderbird and 750 psi minimum

for Cougar, Fairlane, Falcon, Monte-

go or Mustang.

4.
If the pressure gauge reading is

below the minimum specification, the

pump is at fault and should be re-

paired with necessary parts.

5.
If the pressure gauge reading is

at or above the minimum specifica-

tions,
the pump is normal and the

power steering gear or power assist

control valve is at fault.

FLUID PRESSURE TEST-

LINCOLN CONTINENTAL AND

CONTINENTAL MARK III

The pressure testing gauge set, tool

T56L-33610-D, requires modification

to make it adaptable for installation

in the power steering hydraulic sys-

tem. The parts required and the modi-

fication procedure are as follows:
OWER STEERING

PRESSURE LINE

INVERTED FLARE

CONNECTOR

%* TUBE x VA" PIPE

FLARED FEMALE COUPW

%' TUBE x VA" PIPE

G1544.A

FIG. 3—Modified Pressure Gauge

Assembly

a. Power Steering Pressure Line

(refer to the appropriate Parts Catal-

og).

b.
Inverted Flare Connector (3/8

inch OD Tube x 1/4 inch Pipe

Thread).

c. Inverted Flare Connector (5/16

inch OD Tube x 1/4 inch Pipe

Thread).

d. Flared Tube Female Coupling

(3/8 inch OD Tube x 1/4 inch Pipe

Thread).

The connectors and the coupling are

standard-type fittings and can be pur-

chased locally.

e. To modify tool T56L-33610-D,

remove the hose from the hand shut-

off valve block. Install the 3/8 inch x

1/4 inch inverted flare connector in

the valve block, and assemble the

pressure line to the connector (Fig. 3).

Assemble the 3/8 x 1/4 inch coupling

and the 5/16-inch connector to the

free end of the hose leading to the.

pressure gauge.

1.
To check the pump pressure, dis-

connect the front and rear sections of

the pressure line over the number 6

cylinder. Connect the modified pres-

sure-testing gauge assembly, tool

T56L-3361O-D, between the two sec-

tions.

2.
Make sure the hand-valve at the

gauge is fully opened. Start the engine

and cycle the steering gear from stop

to stop to warm up the fluid. Check

the fluid level in the reservoir and add

fluid, if necessary.

3.
Turn the steering wheel to the

full right and full left turn positions

and observe the gauge readings.

Hold the wheels in this position

only long enough to obtain an accu-

rate reading. Do not exceed 5 seconds.

The gauge should read between

1120 and 1250 psi. If the pressure is
less than 1120 psi, close the valve at

the gauge and note the pump pressure.

If it is low with the valve closed, it in-

dicates that the pump is not operating

properly. If the pressure goes up with

the valve closed, it indicates that the

low pressure in the system must be

due to internal leakage in the power

unit, providing all connections are

tight.

4.
Remove the pressure testing

gauge set, and connect the pressure

line at the steering gear. Fill and bleed

the system.

FRONT WHEEL ALIGNMENT

CHECKS

Do not attempt to check and adjust

front wheel alignment without first

making a preliminary inspection of

the front-end parts. Refer to Section

3.

Check all the factors of front wheel

alignment except the turning angle

before making any adjustments. The

turning angle should be checked only

after caster, camber, and toe-in have

been adjusted to specifications.

The front wheel alignment specifica-

tions given in Part 3-13, are correct

only when the vehicle is at curb load.

Before checking or adjusting the

alignment factors, the suspension

alignment spacers must be installed to

obtain the curb Height.

EQUIPMENT INSTALLATION

Equipment used for front wheel

alignment inspection must be accu-

rate.
Whenever possible, front wheel

alignment checks should be performed

on stationary wheel aligning equip-

Too/
- T65P3000-A or S

FIG. 4—Typical Front Alignment

Spacer Installation—Cougar,

Fairlane, Falcon,
Montego,
Mustangprocarmanuals.com

03-01-08
Suspension
—
Steering,
Wheels
And
Tires
—
General Service

03-01-08

3.
Remove the lower (upper on

Mustang and Cougar) cover- to-

housing attaching bolt.

4.
With a clean punch or like in-

strument, clean out or push inward

the loose lubricant in the filler plug

hole and cover to housing attaching

bolt hole.
5.
Slowly turn the steering wheel to

the left stop, lubricant should rise

within the lower cover bolt hole; then

slowly turn the steering wheel to the

right stop, lubricant should rise within

the filler plug hole. If lubricant does

not rise in both the cover bolt hole
and the filler plug hole, add lubricant

until it comes out both holes during

this check.

6. Install the lower (upper on

Mustang and Cougar) cover- to-

housing attaching bolt and the filler

plug.

CLEANING
AND
INSPECTION

FRONT
END
GENERAL

INSPECTION

Do not check and adjust front

wheel alignment without first making

the following inspection for front-end

damage, or wear.

1.
Check for specified air pressures

in all four tires.

2.
Raise the front of the vehicle off

the floor. Shake each front wheel

grasping the upper and lower surfaces

of the tire. Check the front suspension

ball joints and mountings for loose-

ness,
wear, and damage. Check the

brake backing plate mountings. Tor-

que all loose nuts and bolts to specifi-

cation. Replace all worn parts as out-

lined in Part 3-2.

3.
Check the steering gear mount-

ings and all steering linkage connec-

tions for looseness. Torque all mount-

ings to specifications. If any of the

linkage is worn or bent, replace the

parts as outlined in Part 3-5.

4.
Check the front wheel bearings.

If any in-and-out free play is noticed,

adjust the bearings to specifications.

Replace worn or damaged bearings as

outlined in Part 3-12.

5.
Spin each front wheel with a

wheel spinner, and check and balance

each wheel as required.

6. Check the action of the shock

absorbers. If the shock absorbers are

not in good condition, the vehicle may

not settle in a normal, level position,

and front wheel alignment may be af-

fected.

WHEEL INSPECTION

Wheel hub nuts should be inspected

and tightened to specification at pre-

delivery. Loose wheel hub nuts may

cause shimmy and vibration. Elongat-

ed stud holes in the wheels may also

result from loose hub nuts.

Keep the wheels and hubs clean.

Stones wedged between the wheel and

drum and lumps of mud or grease can

unbalance a wheel and tire.
Check for damage that would affect

the runout of the wheels. Wobble or

shimmy caused by a damaged wheel

will eventually damage the wheel bear-

ings.
Inspect the wheel rims for dents

that could permit air to leak from the

tires.

UPPER BALL JOINT

INSPECTION

Ford,
Mercury,
Meteor,

Thunderbird,

Lincoln Continental
and

Continental Mark
III

1.
Raise the vehicle and place floor

jacks beneath the lower arms.

2.
Ask an assistant to grasp the

lower edge of the tire and move the

wheel in and out.

3.
As the wheel is being moved in

and out, observe the upper end of the

spindle and the upper arm.

4.
Any movement between the

upper end of the spindle and the upper

arm indicates ball joint wear and loss

of preload. If any such movement is

observed, replace the upper ball joint.

During
the
foregoing
check,
the

lower ball joint will
be
unloaded
and

may
move.
Disregard
all
such
move-

ment
of the
lower ball
joint.
Also,
do

not mistake loose wheel bearings
for a

worn ball
joint.

Cougar,
Fairlane,
Falcon,

Montego
and
Mustang

1.
Raise the vehicle on a frame

contact hoist or by floor jacks placed

beneath the underbody until the wheel

falls to the full down position as

shown in Fig. 18. This will unload the

upper ball joint.

2.
Adjust the wheel bearings as de-

scribed in Part 3-12.

3.
Attach a dial indicator to the

upper arm and position the indicator
so that the plunger rests against the

inner side of the wheel rim adjacent to

the upper arm ball joint.

4.
Grasp the tire at the top and

bottom, and slowly move the tire in

and out (Fig. 18). Note the reading

(radial play) on the dial indicator. If

MAXIMUM TOLERANCE

F
1500-A

FIG.
T8—Measuring Upper Ball

Joint Radial Play

MAXIMUM TOLERANCE

F14
35-A

FIG.
79—Measuring Lower Ball

Joint Radial Playprocarmanuals.com

03-01-09
Suspension — Steering, Wheels And Tires — General Service

03-01-09

the reading exceeds specifications

(Part 3-13), replace the upper ball

joint.

LOWER BALL JOINT

INSPECTION

Ford,
Mercury, Meteor,

Thunderbird, Lincoln Continental

and Continental Mark III

1.
Raise the vehicle and place

jacks under the lower arms as shown

in Fig. 12. This will unload the lower

ball joints.

2.
Adjust the wheel bearings as des-

cribed in Part 3-12.

3.
Attach a dial indicator to the

lower arm and position the indicator

so that the plunger rests against the

inner side of the wheel rim adjacent to

the lower ball joint.

4.
Grasp the tire at the top and

bottom and slowly move the tire in

and out (Fig. 19). Note the reading

(radial play) on the dial indicator. If

the reading exceeds specifications

(Part 3-13), replace the lower ball

joint.

Cougar, Fairlane, Falcon,

Montego, Mustang

1.
Raise the vehicle on a frame

contact hoist or by floor jacks placed

beneath the underbody until the wheel

falls to the full down position.

2.
Ask an assistant to grasp the

lower edge of the tire and move the

wheel in and out.

3.
As the wheel is being moved in

and out, observe the lower end of the

spindle and the lower arm.

4.
Any movement between the

lower end of the spindle and the lower

arm indicates ball joint wear and loss

of preload. If any such movement is

observed, replace the lower arm.

During the foregoing check, the

upper ball joint will be unloaded and

may move. Disregard all such move-

ment of the upper ball joint. Also, do

not mistake loose wheel bearings for a

worn ball joint.

POWER STEERING GEAR

CLEANING

Disassembly and assembly of the

steering gear and. the sub-assemblies

must be made on a clean workbench.

As in repairing any hydraulically op-

erated unit, cleanliness is of utmost
importance. The bench, tools, and

parts must be kept clean at all times.

Thoroughly clean the exterior of the

unit with a suitable solvent and, when

necessary drain as much of the hy-

draulic fluid as possible. Handle all

parts very carefully to avoid nicks,

burrs,
scratches and dirt, which could

make the parts unfit for use.

Do not clean, wash or soak seals in

cleaning solvent.

INSPECTION

1.
Check the sector shaft contact

surface in the cover for wear. If worn,

replace the cover.

2.
Inspect the input shaft bearing

for cracked races and the balls for

looseness, wear, pitting, end play or

other damage. Check the fit of the

bearing on the input shaft. Replace

the bearing, if required.

3.
Inspect the valve housing for

wear, scoring or burrs.

4.
Inspect the tube seats in the

pressure and return ports in the valve

body for nicks, etc. If necessary, re-

move and replace.

5.
Check the sector shaft contact

surface in the housing for wear. If

worn, replace the bushing or the hous-

ing.

6. Check all fluid passages for ob-

struction or leakage.

7.
Inspect the steering gear housing

for cracks, stripped threads, and mat-

ing surfaces for burrs. Inspect the pis-

ton bore of the housing for scoring or

wear. If necessary, replace the hous-

ing.

8. Check the input shaft bearing

after installation to be sure that it ro-

tates freely.

9. If the valve spool is not free in

the valve housing, check for burrs at

the outward edges of the working

lands in the housing and remove with

a hard stone. Check the valve spool

for burrs and if burrs are found, stone

the valve in a radial direction only.

Check for freedom of the valve again.

10.
Check the piston rack teeth and

sector shaft teeth for nicks and burrs.

FLUSHING THE POWER

STEERING SYSTEM—ALL EXCEPT

LINCOLN CONTINENTAL AND

CONTINENTAL MARK III

Should it be necessary to replace an

inoperative power steering pump, the

need for flushing the steering system

is required when installing the new

pump.
1.
Remove the power steering pump

and remove the pulley as outlined in

Part 3-10.

2.
Install the pulley on a new

pump. Install the pump and connect

only the pressure hose to the pump

(Part 3-10).

3.
Place the fluid return line in a

suitable container and plug the reser-

voir return pipe.

4.
Fill the reservoir with lubricant

(C1AZ-19582-A).

5.
Disconnect the coil wire to pre-

vent the engine from starting and raise

the front wheels off the ground.

6. While approximately two quarts

of steering gear fluid are being poured

into the reservoir, turn the engine over

using the ignition key, at the same

time cycle the steering wheel from

stop to stop.

7.
As soon as all of the lubricant

has been poured in, turn off the igni-

tion key, and attach the coil wire.

8. Remove the plug from the reser-

voir return pipe, and attach the return

hose to the reservoir.

9. Check the reservoir fluid level; if

low, add fluid to the proper level. Do

not overfill.

10.
Lower the vehicle.

11.
Start the engine and cycle the

steering from stop to stop to expel

any trapped air from the system.

POWER STEERING PUMP—ALL

EXCEPT LINCOLN

CONTINENTAL AND

CONTINENTAL MARK III

CLEANING

Wash all parts (except seals) in a

Naptha or Chlorinated-type solvent

and dry with compressed air.

Punch or Rod

RELIEF VALVE PLUNGER

G1607-A

FIG.
20—Cleaning Pump Relief Valveprocarmanuals.com

03-02-22
Suspension

03-02-22

washer and the nut on the upper stud

from the upper side of the spring

upper seat. Torque the nut to specifi-

cations.

6. Extend the shock absorber and

locate the lower stud in the hole in

mounting bracket on the rear axle

housing. Install a new self-locking at-

taching nut and torque to specifica-

tion.

MUSTANG AND COUGAR

Removal

1.
Disconnect the shock absorber

from the spring clip plate (Fig. 30).

2.
Remove the shock absorber ac-

cess cover from the luggage compart-

ment (Fig. 28).-(On convertible mod-

els,
remove the rear seat and seat

back to reach the access cover.)

SHOCK ABSORBER ACCESS COVER
SHOCK ABSORBER UPPER ATTACHING NUT

LUGGAGE COMPARTMENT

FLOOR PANEL

F 1489-A

FIG. 28—Rear Shock Absorber

Access Cover

3.
Remove the shock absorber

upper attaching nut.

4.
Compress the shock absorber

and remove it from the vehicle. Re-

move the bushings and washers from

the shock absorber studs.

Installation

1.
Place the bushing and inner

washer on the shock absorber stud.

2.
Connect the upper stud to the

mounting, and install the bushing,
ACCESS COVER

F 1488-A

FIG. 29—Rear Shock Absorber

Upper Mounting

outer washer, and new nut on the

stud. Torque the nut to specification,

and install the cover.

3.
Connect the lower stud to the

spring clip plate, and install the bush-

ing, outer washer, and new nut on the

stud. Be sure that spring clip plate is

free of burrs. Tighten the nut to speci-

fication.

MONTEGO, FALCON, AND

FAIRLANE (EXCEPT

CONVERTIBLE)

Removal

1.
Open the luggage compartment

door, and remove the spare wheel and

tire.

On the Ranchero, remove the at-

taching screws, and lift the forward

half of the floor panel from the body;

then, remove the access cover from

the opening in the floor pan over the

shock absorber.

On station wagons, remove the ac-

cess cover from the opening in the

seat riser over the shock absorber.

2.
Fold back the floor mat and re-

move the shock absorber access cover

from the floor pan. Remove the nut,

outer washer, and rubber bushing that

attach the shock absorber to the upper

mounting in the floor pan (Fig. 29).

3.
Raise the vehicle and remove the

attaching nut, outer washer and bush-

ing from the shock absorber at the

spring clip plate (Fig. 30). Compress

the shock absorber and remove it

from the vehicle.

4.
If the shock absorber is service-

able and requires new bushings, remove

the inner bushings and washers from

the shock absorber studs.

Installation

1.
Place the inner washer and bush-

ing on each shock absorber stud.
2.
Expand the shock absorber and

position it to the spring clip plate and

to the mounting in the floor pan.

3.
Connect the lower stud to the

spring clip plate, and install the bush-

ing, outer washer, and new nut on the

stud (Fig. 30). Be sure the spring clip

plate is free of burrs.

On the Ranchero, after tightening

the nut to specification, install the for-

ward half of the floor panel.

4.
From the luggage compartment,

install the bushing outer washer and

new attaching nut to the upper mount-

ing stud (Fig. 29). Torque to specifica-

tion. On a station wagon, replace the

floor bed panel (14 screws).

5.
Place the spare wheel and tire in

the luggage compartment, and secure

it in the storage position.

MONTEGO AND FAIRLANE

CONVERTIBLE

Removal

1.
Remove the rear seat cushion

and seat back.

2.
Partially raise the vehicle on a

hoist. With an assistant under the ve-

hicle holding the shock absorber, re-

move the nut from the top of the

shock absorber.

3.
Remove the lower shock absor-

ber attaching nut and remove the

shock absorber.

Installation

1.
Position the washers and bush-

ings on the shock absorber and posi-

tion the shock absorber to the lower

attachment. Install the bushing, outer

washer, and new attaching nut and

torque the nut to specification (Part

3-13).

2.
Lower the vehicle and install the

bushing, outer washer, and new at-

taching nut on the top of the shock

absorber. Torque the nut to specifica-

tion.

3.
Install the rear seat back and

seat cushion.

LINCOLN CONTINENTAL

Removal

1.
Lift the vehicle and place support

stands under the axle housing. Posi-

tion the vehicle with a hoist to relieve

tension on the shock absorbers.

2.
Remove the screws that attach

the shock absorber mounting plate to

the crossmember (Fig. 31).procarmanuals.com

03-08-01
Ford Design Integral Power Steering Gear

03-08-01

PART
3-8
Ford Design Integral Power

Steering Gear

COMPONENT INDEX

STEERING GEAR

Adjustments

Cleaning
and
Inspection
(See

Part 03-01)

Description

Disassembly
and
Assembly

Overhaul

Removal
and
Installation

VALVE CENTERING SHIM

Removal
and
Installation

VALVE SPOOL CENTERING CHECK
MODEL APPLICATION
All Models
Ford

08-02

08-01

08-05

08-06

08-03

08-03

08-02
Mercury
08-02

08-01

08-05

08-06

08-03

08-03

08-02
Meteor
08-02

08-01

08-05

08-06

08-03

08-03

08-02
Cougar
N/A

N/A

N/A

N/A

N/A

N/A

N/A
Fairlane
N/A

N/A

N/A

N/A

N/A

N/A

N/A
Falcon
N/A

N/A

N/A

N/A

N/A

N/A

N/A
Montego
N/A

N/A

N/A

N/A

N/A

N/A

N/A
Mustang
N/A

N/A

N/A

N/A

N/A

N/A

N/A
Lincoln-
Continental
08-02

08-01

08-05

08-06

08-03

08-03

08-02
Thunderbird
08-02

08-01

08-05

08-06

08-03

08-03

08-02
Continental-
Mark
III
08-02

08-01

08-05

08-06

08-03

08-03

08-02

DESCRIPTION

The Ford integral power steering

unit
(Fig. 1) is a
torsion-bar type
of

hydraulic assisted system. This system

furnishes power
to
reduce
the
amount

of turning effort required
at the
steer-

ing wheel.
It
also reduces road shock

and vibrations.

The torsion
bar
power steering unit

includes
a
worm
and
one-piece rack

piston, which
is
meshed
to the
gear

teeth
on the
steering sector shaft.
The

unit also includes
a
hydraulic valve,

valve actuator, input shaft
and
torsion

bar assembly which
are
mounted
on

the
end of the
worm shaft
and
operat-

ed
by the
twisting action
of the tor-

sion
bar.

The torsion-bar type
of
power steer-

ing gear
is
designed with
the one
piece
rack-piston, worm
and
sector shaft
in

one housing
and the
valve spool
in an

attaching housing
(Fig. 1).
This makes

possible internal fluid passages
bet-

ween
the
valve
and
cylinder, thus
eli-

minating
all
external lines
and
hoses,

except
the
pressure
and
return hoses

between
the
pump
and
gear assembly.

The power cylinder
is an
integral

part
of the
gear housing.
The
piston
is

double acting,
in
that fluid pressure

may
be
applied
to
either side
of the

piston.

A selective metal shim located
in

the valve housing
of the
gear
is for the

purpose
of
tailoring steering gear
ef-

forts.
If
efforts
are not
within specifi-

cations they
can be
changed
by in-
creasing
or
decreasing shim thickness

as follows:

Efforts heavy
to the
left—Increase

shim thickness.

Efforts light
to the
left—Decrease

shim thickness.

A change
of one
shim size will
in-

crease
or
decrease steering efforts
ap-

proximately
1 1/2
in-lbs.

Shims
are
available
in the
following

thicknesses
and are
notched
on the

outside diameter
for
identification:

0.0057-0.0063 inch—0 notch

0.0077-0.0083 inch—1 notch

0.0097-0.0103 inch—2 notches

0.0117-0.0123 inch—3 notches

0.0137-0.0143 inch—4 notches

Do
not use
more than
one
shim.
procarmanuals.com

03-09-01
Saginaw Design Integral Power Steering Gear

03-09-01

PART 3-9 Saginaw Design

Integral Power Steering Gear

COMPONENT INDEX

STEERING GEAR

Cleaning and Inspection (See Page 03-01)

Description

Disassembly and Assembly

Mesh Load Adjustment

Removal and Installation

Overhaul
MODEL APPLICATION
All
Models
Ford

09-01

09-03

09-01

09-02

09-04
Mercury
N/A

N/A

N/A

N/A

N/A

N/A
Meteor
N/A

N/A

N/A

N/A

N/A

N/A
Cougar
N/A

N/A

N/A

N/A

N/A

N/A
Fairlane
N/A

N/A

N/A

N/A

N/A

N/A
Falcon
N/A

N/A

N/A

N/A

N/A

N/A
Montego
N/A

N/A

N/A

N/A

N/A

N/A
Mustang
N/A

N/A

N/A

N/A

N/A

N/A
Lincoln-
Continental
N/A

N/A

N/A

N/A

N/A

N/A
Thunderbird
N/A

N/A

N/A

N/A

N/\

N/A
Continental-
Mark III
N/A

N/A

N/A

N/A

N/A

N/A

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

DESCRIPTION

The Rotary Valve Safety power

steering gear operates entirely on dis-

placing fluid to provide hydraulic fluid

pressure assists only when turning. As

the entire gear assembly is always full

of fluid, all internal components of the

gear are immersed in fluid making

periodic lubrication unnecessary. In

addition, this fluid acts as a cushion
to absorb road shocks that may be

transmitted to the driver. All fluid

passages are internal except the pres-

sure and return hoses between the

gear and pump.

The rotary valve provides a smooth

transmission through the driving range

of steering wheel effort. A torsion bar

transmits the road feel to the driver.
Response of the steering gear to effort

applied to the steering wheel has been

greatly increased.

The rack-piston nut is one piece and

is geared to the sector shaft. Lash be-

tween the sector shaft and rack-piston

nut is maintained by an adjusting

screw which is retained in the end o\'

the shaft uear (Eiiz.l).

IN-VEHICLE ADJUSTMENTS AND REPAIRS

During the breaking in period of

the vehicle, it is probable that some

of the factory adjustments will change.

These changes in adjustment do not

necessarily affect the satisfactory op-

eration of the steering gear assembly

and ordinarily do not require re-ad-

justment unless there is excessive lash

or other malfunctioning. The only ad-

justment that should be performed in

the vehicle is the total over center

position load (mesh load) to eliminate

excessive lash between the sector shaft

and rack teeth.

MESH LOAD ADJUSTMENT

1.
Disconnect the Pitman arm from
the sector shaft and remove the steer-

ing wheel hub.

2.
Disconnect the fluid return line

at the reservoir; at the same time cap

the reservoir return line pipe.

3.
Place the end of the return line

in a clean container and cycle the

steering wheel in both directions as

required, to discharge the fluid from

the gear.

4.
Turn the gear 1/2 turn off cen-

ter (either direction). Using a 24 in-

lb torque wrench on the steering wheel

nut, determine the torque required to

rotate the shaft slowly through a 20

degree arc.

5.
Turn the sear back to center and
repeating the method of reading tor-

que as in Step 4, above, loosen the

adjuster lock nut, turn the screw in-

ward with a 7/32-inch Allen wrench

until the reading is equal to 6 in-lbs

in excess of Step 4 above, and retigh-

ten the lock nut while holding the

screw in place.

6. Recheck the readings and re-

place the Pitman arm and the steering

wheel hub.

7.
Connect the fluid return line to

the reservoir and fill the reservoir

with C1AZ-I9582-A Fluid to the

proper level.
procarmanuals.com

03-13-03

Specifications

03-13-03

MANUAL AND POWER

Vehicle

Model

Gear Type

Gear Ratio

Turns of
Strg.

Gr. (Lock to Lock)
®

Lube Type

Lube Capacity

(Lb.)

Worm Bearing

Preload (In Lb)®

Total Center

Meshload(lnLb)®

Adjustments

(All Models)
ASSIST STEERING GEAR SPECIFICATIONS

Ford,

Mercury,

Meteor

SM/VD-1

Manual

24:1

6-2/5

.97
±
.07

4-5

9-10
SMB-D

Manual

19.9:1

4-5/8

.55
±
.05

4-5

9-10

Adjusting
Mustang, Cougar

SMBK

Power Assist

and Manual®

16:1

3-3/4

ESW-M1C87-A

.55
±
.05

3-4®

8-9®

screw to bottom
of
sector

.000 -.002
SMB-F®

Manual

16:1

3-3/4

.55
±
.05

4-5

9-10

shaft T slot clearance:
Falcon,

Mont ego,

Fairlane

SMA-F

Manual

22:1

5-1/2

.87
±
.07

4-5

9-10
SMA-B

Power

Assist

16:1

4

.87
±
.07

3-4

8-9

©Production only
-
for service, use Model SMB-K.

®When used
for
improved
or
competition handling, worm bearing preload must
be
adjusted
to
4-5
In
Lb and total center meshload must
be

adjusted to 9-10 In Lb.

®Gear only
-
not attached to Pitman arm.

0Torque required
to
rotate input shaft
at
approximately 1-1/2 turns either side
of
center (gear
out of
vehicle
or
Pitman arm disconnected).

©Requiredto rotate input shaft and worm assembly past
the
center high point.

STEERING GEAR TORQUE UMITS(FT-LB)

Description

Sector Shaft Cover Bolts

Mesh Load Adjusting Screw Lock Nut

Ball Return Guide Clamp Screw

Preload Adjuster Lock Nut

Valve Housing
to
Gear Housing Screw

Race Retaining Inner Nut

Race Lock Nut

Piston End Cap

Set Screw-Rack Adjustment

Lubricant Fill Plug and Vent
Manual and Power Assist

Ford,
Mercury,

Meteor

30-40

32-40

18-42 (In-Lb)

60-80

3-9®
Fairlane, Falcon,

Montego

17-2?

32-40

18-42 (In-Lb) Pwr.

42-60 (In-Lb) Man.

60-80

3-9®
Mustang

Cougar

15-22

32-40

18-42 (In-Lb)

45-60

3-9®
Power steering

55-70

25-35

60-120 (In-Lb)

35-45

(D

®

50-75
Steering

30-35

20-30

3-6

50-110

50-100

® With tool T66P-3553-B
•
compute the torque as follows:

Length
of
Torque Wrench
X
60 Lb.
Ft.

°rque
"
Length
of
Torque Wrench
+
5.5 Inches

Example: With 13 inch torque wrench

13ln.
X
60 Lb. Ft. 13
X
60 Lb.
Ft.

13
In.
+
5.5 In.
18.5

®With tool T66P-3553-B
•
compute the torque as follows:

Length
of
torque wrench
X
25 Lb.
Ft.

Length of torque wrench
+
5.5 Inches

©Minimum
of
one thread must remain exposed when installed.
-0.703 X60- 42 (Lb.
Ft.)procarmanuals.com