height adjustment FORD MUSTANG 1969 Volume One Chassis

02-01-01

02-01-01

GROUP

2

PART
2-1
PAGE

General Brake Service 02-01-01

PART
2-2

Brake System 02-02-01
PART
2-3

Specifications
PAGE

02-03-01

Part
2-1
General Brake Service

COMPONENT INDEX

ANTI SKID CONTROL SYSTEM

Tests

BRAKE BOOSTER

Adjustments

Cleaning
and
Inspection

Tests

BRAKE PEDAL

Free Height Test

Total Travel Test

DISC BRAKES

Cleaning
and
Inspection

Service Precautions

DRUM BRAKES

Cleaning
and
Inspection

HYDRAULIC SYSTEM BLEEDING

PARKING BRAKE CONTROL

Vacuum Release Test

PARKING BRAKE LINKAGE

Adjustment

PRESSURE DIFFERENTIAL VALVE

Adjustment (Centralize)
MODEL APPLICATION
All
Models

01-04

01-07

01-02

01-01

01-01

01-07

01-07

01-08

01-05

01-07
Ford
N/A

01-03

01-03
Mercury
N/A

01-03

01-03
Meteor
N/A

01-03

01-03
Cougar
N/A

N/A

01-03
Fairlane
N/A

N/A

01-03
F

alcon
N/A

N/A

01-03
Montego
N/A

N/A

01-03
Mustang
N/A

N/A

01-03
Lincoln-
Continental
N/A

01-03

01-04
Thunderbird
01-03

01-03

01-04
Continental-
Mark III
01-03

01-03

01-04

A page number indicates that the item
is for the
vehicle listed
at
the head
of the
column.

N/A indicates that the item
is not
applicable
to
the vehicle listed.

1 BRAKE SYSTEM TESTS

Always check
the
fluid level
in the

master cylinder before performing
the

test procedures.
If the
fluid level
is not

within
1/4
inch
of the top of the mas-

ter cylinder reservoirs,
add
Ford

Brake Fluid
—
Extra Heavy Duty —

Part Number C6AZ-19542-A
(ESA-

M6C25-A)
or
equivalent
for all
brake

applications.
The
extra heavy duty

brake fluid
is
colored blue
for
identifi-

cation purposes.
Do not mix low tem-

perature brake fluids with
the
speci-

fied brake fluid.

Should
one of the
wheel brakes
be

locked
and the
vehicle must
be
moved,

open
the
bleeder screw long enough
to

let
out a few
drops
of
brake fluid.

This bleeding operation will release

the brakes
but
will
not
correct
the

cause
of
trouble.
BRAKE PEDAL FREE

HEIGHT
AND
TRAVEL

MEASUREMENTS

With
the
engine running
for
full

power brake operation, measure
the

brake pedal free height,
and
check
the

brake pedal travel with
the use of the

Brake Pedal Pressure Gauge, Tool

WRE-5OO-5O
as
follows:

BRAKE PEDAL FREE HEIGHT

MEASUREMENT

1.
Insert
a
slender, sharp pointed

prod through
the
carpet
and
sound

deadener
to the
dash panel metal
and

measure
the
distance
to the
brake

pedal
(Fig. 1).

2.
If the
position
of the
pedal
is not

within specification, check
the
brake
pedal linkage
for
missing, worn,
or

damaged bushings,
or
loose attaching

bolts
and
replace them,
if
required.

3.
If the
pedal free height
is
still

out
of
specification, check
the
brake

pedal booster
or
master cylinder
to be

sure
the
correct parts
are
installed.

Replace
the
worn
or
damaged parts
as

necessary.

BRAKE PEDAL TRAVEL

MEASUREMENT

1.
Install
a
Brake Pedal Effort

Gauge
on the
brake pedal
pad
(Fig. 2).

2.
Hook
a
steel measuring tape
to

the brake pedal
as
shown
in Fig. 1.

Measure
and
record
the
distance from

the brake pedal free height position
to

the reference point, which
is at the six
procarmanuals.com

02-01-04
Brakes

02-01-04

ft-lb breakaway torque.
The
breaka-

way torque
is the
torque required
to

turn
the
rear wheels
the
direction
of

forward rotation with
a
torque wrench

and tool shown
in Fig. 5. The
torque

measurement must
be
made relative
to

the center line
of the
wheel.

4.
Release
the
parking brake,
and

check
to
make sure that
the
brake

shoes return
to the
fully released posi-

tion.

5.
Depress
the
parking brake pedal

to
the
third notch. Under normal
con-

ditions, this will hold
the
vehicle satis-

factorily.

6. Release
the
parking brake again,

and check
as in
step
4.

7.
If the
rear brakes
do not
fully

release, check
the
cables
for
kinks
or

binds.
Free
the
cables
as
required.

8. Lower
the
vehicle. Remove
the

torque wrench
and
tool. Install
the

wheel attaching nuts
and
torque them

to specification. Install
the
wheel

cover.

RETAINER-*^ REAR WHEEL

(CABLE ASSEMBLY

EQUALIZER
NUT

PARKING

BRAKE CABLE

AND CONDUIT

ASSEMBLY-2853
SPRING-2A651

SPRING SEAT-2A616
JAM NUT

H1631-A

FIG. 4—Parking Brake Linkage

Adjustment—Fairlane, Montego,

Falcon,
Mustang
and
Cougar
THUNDERBIRD,

CONTINENTAL MARK
III,

AND LINCOLN

CONTINENTAL

Check
the
parking brake cables

when
the
brakes
are
fully released.
If

the cables
are
loose, adjust them
as

follows:

1.
Fully release
the
parking brake

pedal
by
pushing down
the
manual
re-

lease lever.

2.
Depress
the
parking brake pedal

1
1/4
inch from
its
normal released

position.

3.
Raise
the
vehicle with
the
trans-

mission
in
neutral.

4.
Loosen
the
lock
nut and
turn
the

adjusting
nut
forward against
the

equalizer (Figs.
3 and 6)
until there
is

100 ft-lbs breakaway torque.
The

breakaway torque
is the
torque
re-

quired
to
turn
the
rear wheels
the di-

rection
of
forward rotation with
a tor-

que wrench
and
tool shown
in Fig. 5.

The torque measurement must
be

made relative
to the
centerline
of the

wheel. Tighten
the
lock
nut.

5.
Release
the
parking brake,
and

check
to
make sure that
the
brake

shoes return
to the
fully released posi-

tion.

6. Depress
the
parking brake pedal

until
it is
fully engaged.

7.
Release
the
parking brake again,

and check
as in
step
5.

8. Depress
the
pedal
1/2
inch.
The

brakes should
not
drag.

9.
If the
rear brakes
do not
fully

release, check
the
cables
for
kinks
or

binds.
Free
the
cables
as
required.

10.
Lower
the
vehicle. Remove
the

torque wrench
and
tool. Install
the

wheel attaching nuts
and
torque them

to specification. Install
the
wheel

cover.

Tool-T59L
4204-A,

T65K
4204-A,

T66L-4204-A,

OR

Tool-4421UA

E1897-A
POWER BRAKE MASTER

CYLINDER PUSH
ROD

ADJUSTMENT

The push
rod is
provided with
an

adjustment screw
to
maintain
the cor-

rect relationship between
the
booster

control valve plunger
and the
master

cylinder.
If the
plunger
is too
long
it

will prevent
the
master cylinder piston

from completely releasing hydraulic

pressure
and can
cause
the
brakes
to

drag.
If the
plunger
is too
short
it
will

result
in
excess pedal travel
and an

undesirable clunk
in the
booster area.

The adjustment screw
is set to the

correct height
at the
time
of
original

assembly
of the
power unit. Under

normal service
the
adjustment screw

does
not
require
any
further attention

providing
the
original push
rod
assem-

bly remains
in the
original unit.

If
a
check
of the
push
rod
adjust-

ment
is
necessary,
the
push
rod
length

may
be
verified with
a
push
rod
length

gauge
and
measured with
the
engine

running
to
apply vacuum
to the
boost-

er (Fig.
7).

The push
rod
length verification
and

adjustment
of
Midland-Ross power

brake booster assemblies must
be

done according
to the
following proce-

dure:

REAR WHEEL ADJUSTING NUT

CABLES

EQUALIZER

SPRING

CABLE ASSEMBLY H1632-A

FIG. 6—Parking Brake Linkage

Adjustment—Lincoln Continental

FIG. 5—Checking Parking Brake Breakaway Torque
#16
U.J

\

0.980"

0.995"

FIG. 7—Push

Dimensions
>.S. GAUGE SHEET

i

1
STEEL

H1087-E

Rod Gaugeprocarmanuals.com

03-01-03
Suspension — Steering, Wheels And Tires — General Service

03-01-03

4.
Connect a tachometer, start the

engine and operate it at idle speed

until the reservoir fluid temperature

reaches 165 to 175. This temperature

must be maintained throughout the

test. Valve B may be partially closed

to create a back pressure up to 350

psi to hasten the temperature rise. The

reservoir fluid must be at the proper

level.

5.
With the engine operating at rec-

ommended idle rpm and fluid temper-

ature noted in Step 4, close the manu-

al valve B. The minimum acceptable

pressure reading is 620 psi.

6. If the pressure gauge reading is

below the minimum specification, the

pump is at fault and should be re-

paired with necessary parts.

7.
If the reading is at or above the

minimum specification, the pump flow

is normal. Open manual valve B and

proceed to the Pump Fluid Pressure

Test.

PUMP FLUID

PRESSURE TEST

1.
Keep the lines and tools con-

nected as in the Pump Flow Test.

2.
With manual valves A and B

opened fully, operate the engine at

recommended idle speed (Fig. 2).

Close manual valve A, then manual

valve B. Do not keep both valves

closed for more than 5 seconds as this

would abnormally increase the fluid

temperature and cause undue pump

and/or gear wear.

3.
With the valves fully closed, the

pressure gauge should read 1000 psi

minimum for Ford, Mercury, Meteor

or Thunderbird and 750 psi minimum

for Cougar, Fairlane, Falcon, Monte-

go or Mustang.

4.
If the pressure gauge reading is

below the minimum specification, the

pump is at fault and should be re-

paired with necessary parts.

5.
If the pressure gauge reading is

at or above the minimum specifica-

tions,
the pump is normal and the

power steering gear or power assist

control valve is at fault.

FLUID PRESSURE TEST-

LINCOLN CONTINENTAL AND

CONTINENTAL MARK III

The pressure testing gauge set, tool

T56L-33610-D, requires modification

to make it adaptable for installation

in the power steering hydraulic sys-

tem. The parts required and the modi-

fication procedure are as follows:
OWER STEERING

PRESSURE LINE

INVERTED FLARE

CONNECTOR

%* TUBE x VA" PIPE

FLARED FEMALE COUPW

%' TUBE x VA" PIPE

G1544.A

FIG. 3—Modified Pressure Gauge

Assembly

a. Power Steering Pressure Line

(refer to the appropriate Parts Catal-

og).

b.
Inverted Flare Connector (3/8

inch OD Tube x 1/4 inch Pipe

Thread).

c. Inverted Flare Connector (5/16

inch OD Tube x 1/4 inch Pipe

Thread).

d. Flared Tube Female Coupling

(3/8 inch OD Tube x 1/4 inch Pipe

Thread).

The connectors and the coupling are

standard-type fittings and can be pur-

chased locally.

e. To modify tool T56L-33610-D,

remove the hose from the hand shut-

off valve block. Install the 3/8 inch x

1/4 inch inverted flare connector in

the valve block, and assemble the

pressure line to the connector (Fig. 3).

Assemble the 3/8 x 1/4 inch coupling

and the 5/16-inch connector to the

free end of the hose leading to the.

pressure gauge.

1.
To check the pump pressure, dis-

connect the front and rear sections of

the pressure line over the number 6

cylinder. Connect the modified pres-

sure-testing gauge assembly, tool

T56L-3361O-D, between the two sec-

tions.

2.
Make sure the hand-valve at the

gauge is fully opened. Start the engine

and cycle the steering gear from stop

to stop to warm up the fluid. Check

the fluid level in the reservoir and add

fluid, if necessary.

3.
Turn the steering wheel to the

full right and full left turn positions

and observe the gauge readings.

Hold the wheels in this position

only long enough to obtain an accu-

rate reading. Do not exceed 5 seconds.

The gauge should read between

1120 and 1250 psi. If the pressure is
less than 1120 psi, close the valve at

the gauge and note the pump pressure.

If it is low with the valve closed, it in-

dicates that the pump is not operating

properly. If the pressure goes up with

the valve closed, it indicates that the

low pressure in the system must be

due to internal leakage in the power

unit, providing all connections are

tight.

4.
Remove the pressure testing

gauge set, and connect the pressure

line at the steering gear. Fill and bleed

the system.

FRONT WHEEL ALIGNMENT

CHECKS

Do not attempt to check and adjust

front wheel alignment without first

making a preliminary inspection of

the front-end parts. Refer to Section

3.

Check all the factors of front wheel

alignment except the turning angle

before making any adjustments. The

turning angle should be checked only

after caster, camber, and toe-in have

been adjusted to specifications.

The front wheel alignment specifica-

tions given in Part 3-13, are correct

only when the vehicle is at curb load.

Before checking or adjusting the

alignment factors, the suspension

alignment spacers must be installed to

obtain the curb Height.

EQUIPMENT INSTALLATION

Equipment used for front wheel

alignment inspection must be accu-

rate.
Whenever possible, front wheel

alignment checks should be performed

on stationary wheel aligning equip-

Too/
- T65P3000-A or S

FIG. 4—Typical Front Alignment

Spacer Installation—Cougar,

Fairlane, Falcon,
Montego,
Mustangprocarmanuals.com

03-01-04

Suspension — Steering, Wheels And Tires — General Service

03-01-04

Tool
- T 65 P -
3000
B or C

1266-B

FIG. 5—Typical Rear Alignment

Spacer Installation—Cougar,

Fairlane, Falcon, Montego,

Mustang

ment. In the absence of such equip-

ment, portable equipment may be

used and the work may be performed

on a level floor. The floor area should

be level within 1/4 inch from front to

rear of the vehicle and within 1/8 inch

from side to side. Alignment height

spacers (Figs. 4, 8 and 9) are used to

check caster and camber. The spacers

should be omitted when checking toe-

in.

1.
Check the runout of each front

wheel and tire using a dial indicator

against the rim outer band. If the ru-

nout exceeds 1/8 inch, correction may

be made by rotating the wheel on the

drum. When the minimum runout has

been obtained, mark the point of

greatest runout so the wheels can be

positioned as shown in Fig. 10 when

checking the front end alignment.

Hold a piece of chalk against the

wheel rim or the tire sidewall while

spinning the wheels. The chalk will

mark the rim or tire at the point of

greatest runout.

2.
Drive the vehicle in a straight

line far enough to establish the

straight ahead position of the front

wheels, and then mark the steering

wheel hub and the steering column

collar (Fig. ll).Do not adjust the

steering wheel spoke position at this

time. If the front wheels are turned at

any time during the inspection, align

the marks to bring the wheels back to

the straight-ahead position.

3.
With the vehicle in position for

the front end alignment inspection and

adjustment, install the suspension

alignment spacers as follows to esta-

blish the curb height.
F1432-A

FIG. 6—Alignment Spacer

Installation—Rear—Ford,

Mercury, Meteor, Thunderbird,

Continental Mark III

|F1258-Af

FIG. 7— Alignment Spacer

Installation — Rear Lincoln Continental

Tool-T65P-3000-B or -C

F1431-A

FIG. 8—Alignment Spacer

Installation—Front—Ford,

Mercury, Meteor, Thunderbird,

Continental Mark III
F 1499-A

FIG. 9—Alignment Spacer

Installation—Front—Lincoln

Continental

CHALK MARK IN THIS POSITION

WHEN CHECKING TOE-IN AND TOE-OUT

ON TURNS

CHALK MARK IN THIS POSITION

WHEN CHECKING CASTER AND CAMBER

LOCATION OF POINT OF GREATEST

LATERAL RUN-OUT ON FRONT

WHEaS WHEN CHECKING

ALIGNMENT FACTORS

F1215-A

FIG. 70—Front Wheel Position

For Checking Alignment

Lift the front of the vehicle and

position the alignment spacers be-

tween the suspension lower arm and

the frame spring pocket as shown in

Figs.
4, 8 and 9. Be sure the spacer

pin is placed in the correct hole for

the vehicle being checked. The lower

end of the alignment spacers should

be placed over the head of the strut

front attaching bolt. Remove the

bumpers from the right and left rear

side rails. Position the rear alignment

spacers between the rear axle and the

rear side rails as shown in Figs. 5, 6

and 7.

4.
Install the wheel alignment

equipment on the vehicle. Whicheverprocarmanuals.com

03-01-05
Suspension — Steering, Wheels And Tires — General Service

03-01-05

type of equipment is used, follow the

installation and inspection instructions

provided by the equipment manufactu-

rer.

CASTER

Check the caster angle at each front

wheel.

The caster is the forward or rear-

ward tilt of the top of the wheel

spindle (Fig. 12). If the spindle tilts to

the rear, caster is positive. If the

spindle tilts to the front, caster is neg-

ative. The correct caster angle, or tilt,

is specified in Part 3-13.

On Mustang, Cougar, Fairlane,

Falcon and Montego vehicles, the

maximum caster difference for check-

ing purposes must not exceed one de-

gree.
If setting is necessary, then the

maximum difference must not exceed

1/2 degree. On all other vehicles, the

maximum caster difference must never

exceed 1/2 degree.

CAMBER

Check the camber angle at each

front wheel.

Camber is the amount the front

wheels are tilted at the top (Fig. 12).

If a wheel tilts outward, camber is

positive. If a wheel tilts inward, cam-

ber is negative. The correct camber

angle, or outward (positive) tilt is

specified in Part 3-13.

On Mustang, Cougar, Fairlane,

Falcon and Montego vehicles, the

maximum camber difference for

checking purposes must not exceed

one degree. If setting is necessary,
then the maximum difference must

not exceed 1/2 degree. On all other

vehicles, the maximum camber differ-

ence must never exceed 1/2 degree.

TOE-IN

Alignment height spacers should not

be used to check and adjust toe-in.

Toe-in should only be checked and ad-

justed after the caster and camber

have been adjusted to specifications.

Check the toe-in with the front

wheels in the straight-ahead position.

Run the engine so that the power

steering control valve will be in the

center (neutral) position (if so

equipped). Measure the distance be-

tween the extreme front and also be-

tween the extreme rear of both front

wheels. The difference between these

two distances is the toe-in or toe-out.

Correct toe-in, or inward pointing

of both front wheels at the front is

specified in Part 3-13.

FRONT WHEEL

TURNING ANGLE

When the inside wheel is turned 20

degrees, the turning angle of the out-

side wheel should be as specified in

Part 3-13. The turning angle cannot

be adjusted directly, because it is a re-

sult of the combination of caster,

camber, and toe-in adjustments and

should, therefore, be measured only

after these adjustments have been

made. If the turning angle does not

measure to specifications, check the

spindle or other suspension parts for a

bent condition.
ALIGNMENT
MARKS

G-1496-A

FIG. I?—Straight Ahead Position

Marks—Typical

POSITIVE

CAMBER

• •
NEGATIVE-*!
| ^*—

CASTER

ICL
OF TIRE
POSITIVE

CASTER

5r\

CA&U

ANGlE
F1216-A

FIG. 72—Caster and Camber

Angles

COMMON ADJUSTMENTS AND REPAIRS

After front wheel alignment factors

have been checked, make the neces-

sary adjustments. Do not attempt to

adjust front wheel alignment by bend-

ing the suspension or steering parts.

CASTER AND CAMBER

ADJUSTMENTS

FORD, MERCURY, METEOR,

THUNDERBIRDAND

CONTINENTAL MARK III

Caster and camber is adjusted by

loosening the bolts that attach the

upper suspension arm inner shaft to

the frame side rail, and moving the

inner shaft in or out in the elongated

bolt holes with the tool shown in Fig.
13.
The tool should be installed with

the tool pins in the frame holes and

the hooks over the upper arm inner

shaft. Then, tighten the tool hook nuts

snug before loosening the upper arm

inner shaft attaching bolts.

Caster

To adjust the caster angle, tighten

the tool front hook nut or loosen the

rear hook nut (Fig. 14) as required to

increase caster to the desired angle.

To decrease caster, tighten the tool

rear hook nut or loosen the front

hook nut as required (Fig. 14). The

caster angle can be checked without

tightening the inner shaft attaching

bolts.
Check the camber adjustment to

be sure it did not change during the

caster adjustment and adjust if neces-
FIG. 73—Camber and Caster

Adjusting Toolprocarmanuals.com

03-02-12
Suspension

03-02-12

ECCENTRIC

WASHER

F1504-A

FIG. 76 —Measuring Pinion Angle

specification whenever the rear axle

has been removed.

Before checking the drive shaft pin-

ion angle, alignment height spacer

(Tool T65P-3OOO-B or C) must be in-

stalled at a height of 4.30 inches (Fig.

14).

Checking Procedure

The checking and adjusting proce-

dure must be done with the weight of

the vehicle on the front and rear sus-

pension.
UPPER ARM

KET

ECCENTRIC

WASHER

AXLE HOUSING

E1761-A

FIG.
17
—
Pinion
Angle Adjustment

1.
Position the magnetized Tool

T68P-4602-A on a U-joint bearing

cap as shown in Fig. 15.

2.
With the tool suspended straight

down and the adjusting screw to the

left, adjust the dial on the tool until

the left-hand edge of the bubble is ex-

actly on the zero line.

3.
Position the vee magnet on the

drive shaft away from welds and bal-

ance weights (Fig. 15).

4.
Position the magnetized tool

(T68P-4602-A) on the vee magnet

with the adjusting screw to the left in

the same relative position as it was on

the bearing cap (Fig. 16).

5.
Read the position of the bubbles

left-hand edge on the scale to deter-

mine the drive shaft pinion angle. The

reading should be 3 1/2 degrees plus 1
degree on Ford, Mercury or Meteor

models, 7 1/4 degrees plus 3/4 degree

on Thunderbird or Continental Mark

III models.

Adjustment

If the pinion angle is not within

specifications, adjust the pinion angle

as follows:

The upper arm-to-axle housing bolt

and two eccentric washers form an ad-

justing cam mechanism (Fig. 17)

which will tilt the axle housing to the

required angle.

1.
Loosen the upper arm pivot bolt

nuts.

2.
If the angle is less than specifica-

tions,
rotate the adjusting cam for-

ward and recheck the angle. If the

angle is more than specification, ro-

tate the adjusting cam rearward and

recheck the angle.

3.
When the axle housing is adjust-

ed in such a way that the drive shaft

angle reading is within specification,

install new pivot bolt nuts and torque

to specification (Fig. 17).

4.
Lower the vehicle and road test

for proper axle operation.

REMOVAL AND INSTALLATION

HOISTING INSTRUCTIONS

Damage to steering linkage compo-

nents and front suspension struts may

occur if care is not exercised when po-

sitioning the hoist adapters of 2 post

hoists prior to lifting the vehicle.

If a 2 post hoist is used to lift the

vehicle, place the adapters under the

lower arms or the No. 1 crossmember.

Do not allow the adapters to contact

the steering linkage. If the adapters

are placed under the crossmember, a

piece of wood (2 x 4 x 16 inches)

should be placed on the hoist channel

between the adapters. This will pre-

vent the adapters from damaging the

front suspension struts.
FRONT SPRING

REPLACEMENT

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK HI

Removal

1.
Raise the vehicle and support the

front end of the frame with jack

stands.

2.
Place a jack under the lower arm

to support it.

3.
Disconnect the lower end of the

shock absorber from the lower arm.

4.
Remove the bolts that attach the

strut and the rebound bumper to the

lower arm.
5.
Disconnect the lower end of the

sway bar stud from the lower arm.

6. Remove the nut and bolt that se-

cures the inner end of the lower arm

to the crossmember.

7.
Carefully lower the jack slowly

to relieve the spring pressure on the

lower arm, then remove the spring

(Fig. 18).

Installation

1.
Position the spring on the lower

arm so that the lower end properly

engages the seat.

2.
Raise the lower arm carefully

with a jack while guiding the inner

end to align with the bolt hole in the

crossmember. Insert the attaching bolt

in the rear of the crossmember andprocarmanuals.com

03-03-03
Automatic Air Leveling System

03-03-03

COMPRESSOR LINE
AIR
CYLINDER LINE INTAKE PORT EXHAUSTPORT
ADJUSTMENT SCREW

MOUNTING BRACKET
HEIGHT CONTROL VALVE
REAR SUSPENSION UPPER
ARM

FIG. 3—Height Control Valve Installation

Al R CYLINDER
F 1365-A

FIG. 4—Air Cylinder Installation

3 MAJOR REPAIRS

AIR COMPRESSOR

Compressor repair should
be
limit-

ed
to the
cleaning
of the
micro-bon

filter.

REMOVAL

1.
Remove
the
three cover filter
at-

taching screws.
2.
Remove
the
filter
and
cover

gasket.

3.
Wash
the
filter
in
solvent, blow

it
dry
with compressed
air
working

from
the
inside outward.

INSTALLATION

1.
Position
a new
gasket
and the

cover
on the
compressor.
2.
Install
the
three attaching

screws.

HEIGHT CONTROL VALVE

Other than adjusting
the
trim

height,
no
repairs should
be
made
to

the height control valve.

1.
Thoroughly clean exterior
of the

height control valve.procarmanuals.com

03-04-03
Automatic Air Leveling System — Lincoln Continental

03-04-03

outlet lines to their respective parts.

3.
Adjust the trim height as de-

tailed in Section 4.

4.
Connect the link to the arm.

5.
Remove the jack stands and

lower the vehicle.

SUPER LIFT SHOCK ABSORBER

REMOVAL

1.
Raise the vehicle and place jack

stands under the axle to compress the

super lift.

2.
Loosen the air line or lines (right

super lift) slowly to release the air
from the system. Then, disconnect the

line or lines.

3.
Remove the three mounting plate

attaching screws from the upper end

of the super lift.

4.
Remove the attaching nut and

washer from the lower end of the

super lift and remove it from the vehi-

cle.

5.
Remove the nut, outer washer

and the insulator that attach the super

lift to the mounting plate. Remove the

plate, remaining insulator and washer.

INSTALLATION

1.
Position a washer, insulator,

mounting plate, insulator, washer and
nut on the stud at the upper end of

the super lift. Torque the nut to speci-

fication.

2.
Install the mounting plate, outer

insulator, washer and nut on the stud.

Torque the nut to specification.

3.
Attach the mounting plate and

shock absorber to the crossmember

with the attaching screws to specifica-

tions.

4.
Connect the lower end of the

super lift to the mounting stud with

the washers and attaching nut. Torque

the nut to specification.

5.
Connect the air line or lines

(right super lift) to the super lift.

6. Start the engine and check for

leaks.

3 IN-VEHICLE ADJUSTMENTS AND REPAIRS

REGULATOR ADJUSTMENT HEIGHT CONTROL VALVE

The regulator may be adjusted if

the regulator pressure is under 100 psi

with the reservoir pressure at a mini-

mum of 140 psi. If the regulated pres-

sure exceeds 130 psi, the regulator

must be replaced.

To adjust the regulator, remove the

boot and reposition the sleeve and re-

tainer deeper into the body of the re-

gulator, using a deep well socket (Fig.

4).
If the regulator pressure remains

under 100 psi, replace regulator.
SILICONE FLUID

REPLACEMENT

If the height control valve time

delay does not fall within specifica-

tion, the silicone fluid must be re-

placed. Then repeat the time delay

test. If delay is still not within specifi-

cations, replace the height control

valve.

1.
Remove control valve and clean
the exterior of the valve thoroughly.

2.
Position the valve with delay

plug on top. Remove delay plug and

drain silicone fluid from the chamber.

Remove the O-ring from the chamber

(Fig. 5), and discard the O-ring.

3.
Remove the cover plate retaining

ring, using snap ring pliers. Remove

the delay cover from the valve body.

Remove the O-ring from the chamber,

and discard the O-ring.

4.
Place a new O-ring over the

delay plug and install the plug. Tor-

que the plug to 20-30 in-lbs. .

5.
Pour silicone fluid into the delay

piston chamber until fluid level is 5/16

inch below the top edge of the body.

Add or remove fluid with an eye drop-

per until the proper fluid level is

reached.

6. Hold the control valve body in a

vise with the delay chamber elevated

slightly. Carefully operate the lever to

purge trapped air from the fluid.

7.
Place a new O-ring in the groove

around the delay piston bore. Install

5/16" TO

FLUID LEVEL

F 1405 A

FIG. 4—Adjusting Regulator
F1406 A

FIG. 5—Replacing Silicone Fluidprocarmanuals.com

04-02-11
Rear Axle — Removable Carrier Type

04-02-11

If the axle housing is new, install a

new vent. The hose attaching portion

must face toward the front of the ve-

hicle.

2.
If leather-type wheel bearing ser-

vice seals are to be installed, soak the

new rear wheel bearing oil seals in

SAE 10 oil for 1/2 hour before instal-

lation. Wipe a small amount of an oil

resistant sealer on the outer edge of

each seal before it is installed. Do not

put any of the sealer on the sealing

lip.
Install the oil seals in the ends of

the axle housing with one of the tools

shown in Fig. 10 and 12.

3.
Position the replacement axle

housing under the vehicle, and raise

the axle with a hoist or floor jack.

Connect the suspension lower arms to

their mounting brackets on the axle

housing with pivot bolts and nuts. Do

not tighten the bolts and nuts at this

point.

4.
Position the suspension upper

arm in its mounting bracket on the

axle housing, and install the adjusting

bolt, eccentric washers, lock washer

and nut. Leave the bolt and nut loose

at this point.

5.
Position the brake lines to the

axle housing, and secure with the re-

taining clips.

6. Install the brake backing plates

on the axle housing flanges.

7.
Connect the track bar to the

mounting stud, install the washer and

attaching nut, and torque to specifica-

tions.

8. Position the rear coil springs and

insulators in the pockets provided.

9. Connect the lower studs of the

two rear shock absorbers to the

mounting brackets on the axle hous-

ing. Install the attaching nuts, and

torque to specifications.

10.
Connect the vent tube to the

vent on the housing. If axle housing is

new, install a new vent.

11.
Clean the mating surfaces of

the axle housing and differential car-

rier. Position the carrier on the

mounting studs on the housing using a

new gasket between carrier and hous-

ing. Install the copper washers and the

carrier-to-housing attaching nuts, and

torque to specifications.

12.
Make sure that both the front

and rear pivot bolts of the upper and

the two lower arms are loose, and

then raise the axle assembly to con-

trolled curb height (Fig. 15). Hold the

axle at controlled curb height by plac-

ing blocks or pieces of steel pipe be-

tween the axle housing and the bumper

rear screw on the side rail. (See speci-

fications for dimensions.)
FRAME

TIGHTEN ARM

ATTACHING BOLTS

AT 5-45/64 INCH

HEIGHT POSITION
5-45/64 INCH

HEIGHT FOR

INSTALLATION

OF ARMS

E 1600-B

FIG. 75 -Axle Normal Curb

Height and Controlled Height

for Arm Installation

13.
With the axle at controlled curb

height, torque the suspension upper

and lower arm front pivot bolts and

nuts to specifications. Torque the

lower arm-to-axle housing pivot bolts

and nuts to specifications.

14.
Remove the oil seal replacer

tool from the transmission extension

housing. Position the drive shaft so

that the front U-joint slip yoke splines

to the transmission output shaft.

15.
Connect the drive shaft to the

U-joint flange, aligning the scribe

marks made on the drive shaft end

yoke and the axle U-joint flange dur-

ing the removal procedure. Install the

U-bolts and nuts and torque to speci-

fications.

16.
Carefully slide the two axle

shaft assemblies in the axle housing.

The shorter shaft goes into the left

side of the housing. Use care in slid-

ing the axle shafts into the housing so

that the rough forging of the shaft will

not damage the oil seal. Start the axle

splines into the differential side gear,

and push the shaft in until the rear

wheel bearing bottoms in the housing.

17.
Install the rear wheel bearing

retainers on the attaching bolts on the

axle housing flanges. Install the nuts

on the bolts and torque to specifica-

tions.

18.
If the rear brake shoes were

backed off, adjust the brakes as out-

lined in Part 2-1, and install rubber

plugs in the adjuster slots.

19.
Install the two rear brake

drums and the drum attaching (Tin-

nerman) nuts.

20.
Install the rear wheels and tires.

21.
Fill the rear axle to the bottom

of the filler plug hole located in either

the carrier casting or housing cover

with specified lubricant. Be sure that

the axle is in operating position.

22.
Road test the vehicle to be sure

that pinion and driveshaft angles are
correct. Any shudder during heavy ac-

celeration, or deceleration may require

a pinion and driveshaft angle re-

adjustment as detailed in Driveshaft

and Pinion Angle Adjustment, Group

3,
Part 3-2.

AXLE HOUSING (LEAF

SPRING SUSPENSION)

REMOVAL

1.
Raise the vehicle and support it

with safety stands under the rear

frame member.

2.
Drain the lubricant from the

axle.

3.
Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position of the

drive shaft at assembly. Disconnect

the drive shaft at the drive pinion

flange.

4.
Disconnect the lower end of the

shock absorbers.

5.
Remove the wheels, brake drums

and both axle shafts as outlined in

Section 2.

6. Remove vent hose front vent

tube (Corbin clamp) and remove vent

tube from brake tube junction and

axle housing.

7.
Remove the hydraulic brake T-

fitting from the axle housing. Do not

open the hydraulic brake system lines.

Remove the hydraulic brake line from

its retaining clip on the axle housing.

8. Remove both axle shaft oil seals

with the tool shown in Fig. 8.

9. Remove both brake backing

plates from the axle housing and sus-

pend them above the housing with

mechanic's wire. The hydraulic brake

lines and the parking brake cables are

still attached to the brake backing

plates.

10.
Support the rear axle housing

on a jack, and then remove the spring

clip nuts. Remove the spring clip

plates (Fig. 16).

11.
Lower the axle housing and re-

move it from under the vehicle.

12.
If the axle housing is being re-

placed, transfer all the differential and

pinion parts to the new housing. See

Section 4, Major Repair Operation*.

INSTALLATION

1.
Raise the axle housing into posi-

tion so that the spring clip plates can

be installed. On a Montego or Fair-

lane,
position the spring upper insula-

tors and retainers between the axle

housing and springs and install theprocarmanuals.com

06-02-03
Ford Design Three Speed Transmission

06-02-03

STOP
PIN

GROMMET

Tool -
T67P.7347.A

GROMMET

LEVER

CONTROL ROD REMOVAL
^S.
GROMMET INSTALLATION

SET STOP PIN SO THAT THE GROMMET

Tool
-
T67P.734LA
AND
SHIFT ROD ARE PROPERLY SEATED
OMMET—^

SEATED
\

CONTROL ROD INSTALLATION

CONTROL ROD

STOP
PIN

FIG. 4—Removing
or
Installing Shift Linkage Grommet

GEAR SHIFT LINKAGE

ADJUSTMENT—FLOOR MOUNTED

1.
Loosen
the
three shift linkage

adjustment nuts. Install
a 1/4
inch
di-

ameter alignment pin through the con-

trol bracket and lever alignment holes

shown
in Fig. 18.

2.
Tighten
the
three linkage adjust-

ment nuts
and
then remove
the
align-

ment
pin.

3.
Check
the
gear shift lever
for a

smooth crossover.

COLUMN-MOUNTED

SHIFT LINKAGE

GROMMET REMOVAL
AND

INSTALLATION

The column-mounted shift lever
as-
sembly incorporates
an oil
impregnat-

ed plastic grommet
in the
end
of
each

lever
arm. A
special tool T67P-

7341-A
is
required
to
install the grom-

met
in the
shift lever,
and to
install

the shift linkage
rod
into
the
grom-

met. Remove
and
install
the
grommet

as follows:

1.
Place
the
lower
jaw of the
tool

between
the
shift lever
and the
shift

rod.
Position
the
stop
pin
against
the

end
of the
shift
rod
(Fig.
4)
and force

the
rod out of the
grommet. Remove

the grommet from
the
shift lever
by

cutting
off the
large shoulder with
a

sharp knife. The groin met must
be re-

moved from
the
shift lever
and a new

one installed each rime
'he rod is
dis-

connected.

2.
Before installing
a
new grommet,
C 2090-A

adjust
the
stop
pin as
necessary
to

properly install
the
grommet and coat

the outside
of
the grommet with lubri-

cant. Then, place
the
grommet
on the

stop
pin and
force
it
into
the
shift

lever hole. Turn
the
grommeit several

times
to be
sure
it is
properly seated.

3.
Readjust
the
stop
pin to a
length

which
is
sufficient
to
install
the
shift

rod into
the
grommet
(Fig.
4).
If
the

pin height
is not
adjusted,
the
shift

rod
may be
pushed
too far
through

the grommet causing damage
to the

grommet retaining
lip.

4.
With
the pin
height properly
ad-

justed, position
the
shift
rod on the

tool
and
force
the rod
into
the
grom-

met until
the
groove
in the rod
seats

on
the
inner retaining
lip of
the grom-

met.

REMOVAL AND INSTALLATION

REMOVAL

1.
Raise
the
vehicle
on a
hoist.

2.
Mark
the
drive shaft
so
that
it

may
be
installed
in the
same relative

position. Disconnect
the
drive shaft

from
the
rear U-joint flange.

3.
Slide
the
front
of the
drive shaft
out
of the
transmission extension

housing
and off the
output shaft
In-

sert
the
tool shown
in (Fig. 2),
Part

6-1 into the extension housing
to
pre-

vent
the
lubricant from leaking
out of

the transmission.

4.
Remove
the cap
screw
and
lock

washer that secures
the
speedometer
cable retainer
to the
extension hous-

ing. Pull
the
speedometer cable
out of

the extension housing.

5.
On
vehicles equipped with
a

column-mounted gear shift selector,

remove
the
shift rods from
the
shift

levers
at
the transmission. On vehicles

equipped with
a
floor-mounted gearprocarmanuals.com