weight FORD MUSTANG 1969 Volume One Chassis

03-02-12
Suspension

03-02-12

ECCENTRIC

WASHER

F1504-A

FIG. 76 —Measuring Pinion Angle

specification whenever the rear axle

has been removed.

Before checking the drive shaft pin-

ion angle, alignment height spacer

(Tool T65P-3OOO-B or C) must be in-

stalled at a height of 4.30 inches (Fig.

14).

Checking Procedure

The checking and adjusting proce-

dure must be done with the weight of

the vehicle on the front and rear sus-

pension.
UPPER ARM

KET

ECCENTRIC

WASHER

AXLE HOUSING

E1761-A

FIG.
17
—
Pinion
Angle Adjustment

1.
Position the magnetized Tool

T68P-4602-A on a U-joint bearing

cap as shown in Fig. 15.

2.
With the tool suspended straight

down and the adjusting screw to the

left, adjust the dial on the tool until

the left-hand edge of the bubble is ex-

actly on the zero line.

3.
Position the vee magnet on the

drive shaft away from welds and bal-

ance weights (Fig. 15).

4.
Position the magnetized tool

(T68P-4602-A) on the vee magnet

with the adjusting screw to the left in

the same relative position as it was on

the bearing cap (Fig. 16).

5.
Read the position of the bubbles

left-hand edge on the scale to deter-

mine the drive shaft pinion angle. The

reading should be 3 1/2 degrees plus 1
degree on Ford, Mercury or Meteor

models, 7 1/4 degrees plus 3/4 degree

on Thunderbird or Continental Mark

III models.

Adjustment

If the pinion angle is not within

specifications, adjust the pinion angle

as follows:

The upper arm-to-axle housing bolt

and two eccentric washers form an ad-

justing cam mechanism (Fig. 17)

which will tilt the axle housing to the

required angle.

1.
Loosen the upper arm pivot bolt

nuts.

2.
If the angle is less than specifica-

tions,
rotate the adjusting cam for-

ward and recheck the angle. If the

angle is more than specification, ro-

tate the adjusting cam rearward and

recheck the angle.

3.
When the axle housing is adjust-

ed in such a way that the drive shaft

angle reading is within specification,

install new pivot bolt nuts and torque

to specification (Fig. 17).

4.
Lower the vehicle and road test

for proper axle operation.

REMOVAL AND INSTALLATION

HOISTING INSTRUCTIONS

Damage to steering linkage compo-

nents and front suspension struts may

occur if care is not exercised when po-

sitioning the hoist adapters of 2 post

hoists prior to lifting the vehicle.

If a 2 post hoist is used to lift the

vehicle, place the adapters under the

lower arms or the No. 1 crossmember.

Do not allow the adapters to contact

the steering linkage. If the adapters

are placed under the crossmember, a

piece of wood (2 x 4 x 16 inches)

should be placed on the hoist channel

between the adapters. This will pre-

vent the adapters from damaging the

front suspension struts.
FRONT SPRING

REPLACEMENT

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK HI

Removal

1.
Raise the vehicle and support the

front end of the frame with jack

stands.

2.
Place a jack under the lower arm

to support it.

3.
Disconnect the lower end of the

shock absorber from the lower arm.

4.
Remove the bolts that attach the

strut and the rebound bumper to the

lower arm.
5.
Disconnect the lower end of the

sway bar stud from the lower arm.

6. Remove the nut and bolt that se-

cures the inner end of the lower arm

to the crossmember.

7.
Carefully lower the jack slowly

to relieve the spring pressure on the

lower arm, then remove the spring

(Fig. 18).

Installation

1.
Position the spring on the lower

arm so that the lower end properly

engages the seat.

2.
Raise the lower arm carefully

with a jack while guiding the inner

end to align with the bolt hole in the

crossmember. Insert the attaching bolt

in the rear of the crossmember andprocarmanuals.com

03-02-16
Suspension

03-02-16

2.
Place a jack under the outer end

of the arm.

3.
Tape the upper and lower spring

insulators to the spring.

4.
Compress the coil spring with

Tool 5310-A (Fig. 23) and place the

spring and insulators in position. Be

sure both ends of the spring are prop-

erly seated, and raise the arm. Guide

the spindle boss over the ball joint

stud.

5.
Install the ball joint stud retain-

ing nut and torque it to specification.

Continue tightening the nut to line up

the cotter pin hole. Install a new cot-

ter pin.

6. Connect the stabilizer bar to the

lower arm. Torque the nut to specifi-

cation.

7.
Connect the drag strut to the

lower arm. Torque the nuts to specifi-

cation.

8. Install the shock absorber.

9. Tighten the splash shield attach-

ing bolts to specifications.

10.
Install the hub and rotor on the

spindle and adjust the wheel bearings.

11.
Install the caliper to the spindle

and tighten the attaching bolts to

specifications. Check for the correct

flexible hose routing (Part 2-2).

12.
Install the wheel and tire on the

hub.
Torque the wheel lug nuts to

specifications and remove the support

stands.

13.
With the front end weight of

the car on the wheels, torque the

lower arm-to-crossmember bolt at-

taching nut to specification.

FRONT SUSPENSION

LOWER ARM

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK III

Removal

1.
Raise the front of the vehicle and

position safety stands under both sides

of the frame just back of the lower

arms.

2.
Remove the hub cap or wheel

cover.

3.
If equipped with drum type

brakes—Remove the wheel and tire

and brake drum as an assembly. Re-

move the brake backing plate attach-

ing bolts and remove the backing

plate from the spindle. Wire the back-

ing plate to the underbody to prevent

damage to the brake hose.

4.
If equipped with disc brakes-

—Remove the wheel and tire from the
•Tool—5310-A

F 1491-A

FIG. 23—Coil Spring Compressed

for Installation

F1437-A

FIG. 24—Removing Front Spring

—Lower Arm Replacement

hub.
Remove 2 bolts and washers that

attach the caliper and brake hose to

the spindle. Remove the caliper from

the rotor and wire it to the underbody

to prevent damage to the brake hose.

Then, remove the hub and rotor from

the spindle.

5.
Disconnect the lower end of the

shock absorber, and push it up to the

retracted position.

6. Disconnect the stabilizer bar link

from the lower arm.

7.
Remove the cotter pins from the

upper and lower ball joint stud nuts.

8. Remove 2 bolts and nuts attach-

ing the strut to the lower arm.

9. Loosen the lower ball joint stud

nut one or two turns. Do not remove

the nut from the stud at this time.

10.
Install Tool T57P-3OO6-A bet-

ween the upper and lower ball joint

studs (Fig. 7). The tool should be

seated firmly against the ends of both

studs and not against the stud nuts.

11.
With a wrench, turn the adapter

screw until the tool places the stud

under tension. Tap the spindle near

the lower stud with a hammer to loos-
en the stud in the spindle. Do not

loosen the stud from the spindle with

tool pressure only.

12.
Position a floor jack under the

lower arm (Fig. 24) and remove the

lower ball joint stud nut.

13.
Lower the floor jack and re-

move the sprina and insulator (Fie.

25).

14.
Remove one nut and bolt at-

taching the lower control arm to the

No.
2 crossmember and remove the

lower arm (Fig. 24).

Installation

1.
Position the lower arm to the

No.
2 crossmember and loosely install

the attaching bolt and nut (Fig. 1).

2.
Position the spring and insulator

to the upper spring pad and lower

arm. Using a floor jack, compress the

spring and guide the lower ball joint

stud into the spindle hole.

3.
Install the ball joint stud attach-

ing nut and torque to specification.

Continue to tighten the nut until the

cotter pin hole is in line with the nut

slots.
Install a cotter pin in the upper

and lower ball joint studs.

4.
Pull the shock absorber down

and connect it to the lower arm.

5.
Position the strut and bumper to

the lower arm. Install the attaching

bolts and nuts and torque to specifica-

tion.

6. Torque the lower arm to No. 2

crossmember attaching bolt and nut to

specifications.

7.
Position the stabilizer bar link to

the lower arm and install the attach-

ing nuts.

8. If equipped with drum type

brakes—Position the brake backing

plate to the spindle and install the at-

taching bolts. Torque the bolts to spe-

cification. Adjust the brakes as out-

lined in Group 2. Install the wheel,

tire,
and drum to the spindle and ad-

just the wheel bearings as outlined in

Part 3-12.

If equipped with disc brakes-Install

the hub and rotor on the spindle.

Position the caliper over the rotor and

install the attaching bolts. Torque the

bolts to specification. Install the

wheel and tire on the wheel hub and

adjust the wheel bearings as outlined in

Part 3-12.

9. Install the hub cap or wheel

cover.

10.
Remove the safety stands and'

lower the vehicle.

11.
Check the caster, camber, and

toe-in and adjust as required (Section

2,
Part 3-1).procarmanuals.com

03-02-19

Suspension

03-02-19

6. Raise the upper arm to free the

ball joint stud from the spindle. Wire

the upper end of the spindle to the un-

derbody to prevent damage to the

brake hose.

7.
Mark the position of the upper

arm shaft on the underbody member

to facilitate making caster and camber

adjustments after installation of the

upper arm.

8. Remove the suspension upper

arm-to-underbody attaching bolts,

lock washers, and attaching nuts.

Then, remove the upper arm.

Installation

1.
Position the upper arm shaft on

the underbody member. Line up the

shaft with the marks made before re-

moval of the arm.

2.
Install the attaching bolts and

lock washers. FABRICATE A

TOOL, AS SHOWN IN Fig. 27, to

hold the nut in place while starting the

attaching bolt into the nut. Remove

the tool; then, tighten the attaching

bolts to specification.

3.
Guide the ball joint stud into the

spindle. Install the attaching nut and

torque it to specification. Continue

tightening the nut to line up the cotter

pin hole. Install a new cotter pin.

4.
Install the wheel and tire, and

torque the wheel lug nuts to specifica-

tion.

5.
With the front end weight of the

car on the wheels, torque the bolts at

the ends of the upper arm shaft to

specification if the bushings were re-

placed.

6. Check the front wheel alignment.

FRONT WHEEL SPINDLE

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK III

Removal

1.
Raise the vehicle until the front

wheel clears the floor, and place a

support under the frame.

2.
Remove the hub cap or wheel

cover.

3.
If equipped with drum type

brakes—remove the wheel and tire

and brake drum as an assembly (Part

3-12). Remove the brake backing

plate attaching bolts and remove the

backing plate from the spindle. Wire

the backing plate to the underbody to

prevent damage to the brake hose.
1/16" GAUGE
-*.

STEEL (REFERENCE)

—3/16'
3/8'

1/2" DIAMETER PLUG WELD

F 1501-A

FIG. 27 -Upper Arm Shaft Installing Tool

4.
If equipped with disc brakes—re-

move the wheel and tire from the hub.

Remove 2 bolts and washers retaining

the caliper and brake hose to the

spindle. Remove the caliper from the

rotor and wire it to the underbody to

prevent damage to the brake hose.

Then, remove the hub and rotor from

the spindle (Part 3-12). Remove 3

bolts attaching the splash shield to the

spindle and remove the splash shield.

5.
Remove the steering connecting

rod from the spindle arm with tool

OTC462.

6. Remove the cotter pins from

both ball joint stud nuts, and loosen

the nuts one or two turns. Do not re-

move the nuts from the studs at this

time.

7.
Install the ball joint remover tool

between the upper and lower ball joint

studs (Fig. 7). The tool sho.uld seat

firmly against the ends of both studs

and not against the stud nuts.

8. Turn the tool nut with a wrench

until the tool places the studs under

tension, and, with a hammer, tap the

spindle near the stud to loosen them

in the spindle. Do not loosen the studs

in the spindle with tool pressure only.

9. Position a floor jack under the

lower control arm.

10.
Remove the ball joint stud nuts

and lower the lower arm enough to re-

move the spring and the spindle.
Installation

1.
Position the spindle to the lower

ball joint stud and install the attaching

nut. Torque the nut to specification.

Continue to tighten the nut until the

cotter pin hole is in line with the slots

in the nut. Then, install the cotter pin.

2.
Position the spring and raise the

lower arm and guide and upper ball

joint stud into the spindle hole and in-

stall the attaching nut. Torque the nut

to specification and install the cotter

pin as outlined in the preceeding step.

3.
Remove the floor jack from

under the lower arm.

4.
Attach the steering connecting

rod to the spindle and install the nut.

Torque the nut to specification. Con-

tinue to tighten the nut until the cotter

pin hole is in line with the slots in the

nut. Then, install the cotter pin.

5.
If equipped with drum type

brakes—Position the brake backing

plate to the spindle and install the at-

taching bolts. Torque the bolts to spe-

cification. Adjust the brakes as out-

lined in Part 2-2. Install the wheel,

tire,
and drum to the spindle and ad-

just the wheel bearings as outlined in

Part 3-12).

6. If equipped with disc brak-

es—Install the splash shield on the

spindle and torque the attaching bolts

to specification (Part 3-13). Install theprocarmanuals.com

03-02-25
Suspension

03-02-25

pivot bolts and nuts to specification

(Part 3-13).

5.
Connect the track bar to the

frame bracket with a new nut and

bolt. Torque the nut to specification

(Part 3-13).

6. Remove the alignment spacers

and jack stands and lower the vehicle.

REAR SUSPENSION-

UPPER ARM

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK HI

Removal

1.
Raise the vehicle and support the

frame side rails with jack stands.

2.
Support the rear axle, then dis

connect the track bar from the frame

bracket.

3.
Lower the axle and support axle

under differential pinion nose, as well

as under axle.

4.
Remove the nut, bolt and two

washers that attach the upper arm to

the axle housing. Disconnect the arm

from the housing.

5.
Remove the nut and bolt that se-

cures the upper arm to the crossmem-

ber and remove the arm.

Installation

1.
Hold the upper arm in place on

the crossmember and install a new at-

taching bolt, a new lockwasher and a

new nut. Do not tighten the nut at this

time.

2.
Secure the upper arm to the axle

housing with a new attaching bolt,

two washers and a new nut. Do not

tighten the nut at this time.

3.
Install alignment spacers be-

tween the rear axle housing and

frame.

4.
Connect the track bar to the

frame bracket with a new nut and

bolt. Torque the nut to specifications.

5.
Torque the upper arm front nut

to specification. Remove the align-

ment spacers and the jack stands.

6. Adjust the pinion angle and tor-

que the rear nut to specification.

7.
Lower the vehicle.

TRACK BAR

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK HI

1.
Raise the vehicle on an axle con-

tact hoist.
FRONT PIVOT BOLT
LOWER ARM
REAR PIVOT BOLT NUT

F1439-A

FIG. 33—Rear Suspension Lower Arm Installed

Tool-T64K-5781-B4 (Thrust
Washer)

FIG. 34—Rear Spring Front Bushing Removal—Typical
F 1485. A

2.
Remove rubber cover at axle at-

tachment on track bar.

3.
Remove the nut and washer at-

taching the track bar to the upper arm

bracket and disengage the track bar

from the mounting stud (Fig. 33).

4.
Remove the nut and bolt attach-

ing the track bar to the frame side rail

and remove the track bar.

5.
Position the track bar to the

frame side rail and install a new at-

taching bolt and new nut.

6. Position the track bar on the

upper arm bracket mounting stud and

install a new washer and a new at-

taching nut. Torque the track bar at-

taching bolt and nuts to specification

(Part 3-13). Lubricate rubber cover

with synthetic rubber lubricant and in-

sert over end of stud onto washer.

Then, lower the vehicle.
REAR SPRING AND/OR BUSHING

COUGAR, FAIRLANE,

FALCON, MONTEGO,

MUSTANG

Removal

1.
Raise the vehicle on a hoist and

place supports beneath the underbody

and under the axle.

2.
Disconnect the lower end of the

shock absorber from the spring clip

plate and push the shock out of the

way. Remove the supports from under

the axle.

3.
Remove the spring clip plate

nuts from the U-bolts; then, remove

the plate (Fig. 31). Raise the rear axle

just enough to remove the weight from

the spring.

4.
Remove the two attaching nuts,

and rear shackle bar, and the two

shackle inner bushings.procarmanuals.com

03-02-28
Suspension

03-02-28

used, these components should
be re-

placed
on the
bench.

Do not wash the ball joint with sol-

vent.
The
solvent
may
attack parts

within the joint.

BUSHING AND INNER

SHAFT REPLACEMENT

LINCOLN CONTINENTAL

Always replace both upper
arm

bushings,
if
either bushing
is
worn
or

damaged. Install only
new
bushings

when replacing
the
inner shaft. Refer

to Section
3 for
the upper arm remov-

al procedure.

1.
Remove
the
bolts, lock washers,

and flat washers from the ends
of
the

upper arm shaft.

2.
Assemble
the
remover, tool

3044-LA,
to the
shaft
at the
front

bushing. Press
the
bushing
out of the

arm using
the
support cup, tool 6069-

H,
and the
remover tool 3044-AB3

(Fig. 40).

PRESS RAM

FIG.
40
—Removing Upper
Arm

Front Bushing

3.
Remove
the
shaft.

4.
Remove
the
upper
arm
rear

bushing using
the
support
cup,
tool

3069-H, and
the
remover, tool 3069-L

(Fig. 41).

5.
Both upper
arm
bushings
are

pressed into the arm from the outside

toward the inside
of
the arm. To facil-

itate installation, use silicone
or
liquid

oap
as a
lubricant.
See
Fig.
41 for
PRESS RAM

Tool-3069-H

F 1480-A

FIG. 41—Removing Upper
Arm

Rear Bushing

proper assembly
of the
shaft
and

bushings.

6. Press the upper arm rear bushing

into
the arm
using
the
support cup,

tool 3069-H,
and the
replacer, tool

3068 (Fig. 43). Press
the
bushing
in

until
the
shoulder stop
is
reached.

7.
Insert
the end of the
shaft into

the rear bushing. Press the front bush-

ing onto
the
shaft
and
into
the arm

using the replacer, tool 3068 (Fig. 44).

REAR BUSHING
FRONT BUSHING

F 1479-A

FIG. 42— Upper Arm, Shaft,
and

Bushing Assembly

PRESS RAM

Tool— 3068

JF 1478-A
Bottom the bushing flange against the

flange
in the
arm.

8. Install
the
flat washers, lock-

washers,
and
bolts
at
the ends
of
the

upper
arm
shaft.
Do not
tighten
the

bolts
at
this time. These must
be

tightened after
the
arm assembly
has

been installed, and when the front end

weight
of
the vehicle
is
on the wheels.

These bolts
are
made
of a
special

material. Use only the specified bolt
if

replacement
is
necessary.

PRESS
RAM

FIG. 43—Installing Upper
Arm

Rear Bushing
FIG. 44—Installing Upper
Arm

Front Bushing

REAR SPRING OVERHAUL-

SPRING REMOVED

LINCOLN CONTINENTAL

Front Hanger Assembly

If
the
front hanger
or
bushings
are

to
be
replaced, proceed
as
follows:

1.
Remove
the
nuts and lock wash-

ers from
the
spring front mounting

bolt (Fig.
6).

2.
Tap the
spring mounting stud

out
of the
bushing
and
hanger, then

separate
the
hanger from
the
spring.

3.
Remove
the
front bushing from

the spring with tool T64N-5781-A.

4.
Install
the
bushing
in the
spring

with tool T64N-5781-A.

5.
Assemble the front hanger
to
the

spring
eye and
install
the
spring

mounting stud through
the
hanger,

bushings,
and
spring eye
as
shown
in

Fig.
6.

6. Install the lock washers and nuts

on
the
mounting stud
and
tighten
the

outboard
nut to
specification. Tighten

the inboard
nut to
specification with

the vehicle
at
curb riding height.procarmanuals.com

03-08-07
Ford Design Integral Power Steering Gear

03-08-07

Press Ram
Tool-

T65P.3524-A1

G1362-A

FIG.
17—Installing
Oil Seal in

Valve Housing

11.
Place the dust seal in the hous-

ing with the dished side (rubber side)

facing out. Drive the dust seal into

place with the tool shown in Fig. 11.

the seal must be located behind the

undercut in the input shaft when it is

installed.

Worm and Valve

1.
Remove the snap ring from the

end of the actuator.

2.
Slide the control valve spool

(Fig. 6) off the actuator.

3.
Install the valve spool evenly and

slowly with a slight oscillating motion

into the flanged end of valve housing

with the Valve identification groove

between the valve spool lands out-

ward, checking for freedom of valve

movement within the housing working

area. The valve spool should enter the

housing bore freely and fall by its own

weight.

4.
If the valve spool is not free,

check for burrs at the outward edges

of the working lands in the housing

and remove with a hard stone.

5.
Check the valve for burrs and if

burrs are found, stone the valve in a

radial direction only. Check for free-

dom of the valve again.

6. Remove the valve spool from the

housing.

7.
Slide the spool onto the actuator

making, sure that the groove in the

spool annulus is toward the worm.

8. Install the snap ring to retain the

spool.

9. Check the clearance between the

spool and the snap ring. The clearance

should be between 0.002-0.005 inch. If

the clearance is not within these lim-

its,
select a snap ring that will allow a

clearance of 0.003 inch.
STEERING GEAR HOUSING

J

UPPER SEAL

I LOWER SEAL

SNAP RING

SPACER WASHER

FIG. 12—Steering Gear Housing Disassembled

Tool - T59L - 100-B

Tool T57L-500 - A

G1551-A

FIG. 13—Removing Lower Seal

Piston and Ball Nut

1.
Remove the teflon ring and the

O-ring (Fig. 7) from the piston and

ball nut.

2.
Dip a new O-ring in gear lubri-

cant and install it on the piston and

ball nut.

3.
Install a new teflon ring on the

piston and ball nut being careful not

to stretch it any more than necessary.

Steering Gear Housing

1.
Remove the snap ring and the

spacer washer (Fig. 12) from the

lower end of the steering gear housing.

2.
Remove the lower seal from the

housing as shown in Fig. 13. Lift the

spacer washer from the housing.

3.
Remove the upper seal in the

same manner as the lower seal.

4.
Dip both sector shaft seals in

gear lubricant.
SHORT END

AWAY

FROM SEAL
G1550-A

Press Rom

G1374-A

FIG. 14—Installing Sector Shaft

Inner Seal

5. Apply Lubricant to the sector

shaft seal bore of the housing and

position the sector shaft inner seal

into the housing with the lip facing in-

ward. Press the seal into place with

the tool shown in Fig. 14. Place a spa-

cer washer (0.090 inch) on top of the

seal and apply more Lubricant to the

housing bore.

6. Place the outer seal in the hous-

ing with the lip facing inward and

press it into place as shown in Fig. 15.

Then, place a 0.090 inch spacer wash-

er on top of the seal.

7.
Position the snap ring in the

housing. Press the snap ring into the

housing with the tool shown in Fig. 15

to properly locate the seals and en-

gage the snap ring in the groove.

STEERING GEAR

ASSEMBLY

Do not clean, wash, or soak seals in

cleaning solvent.procarmanuals.com

04-02-13

Rear Axle
—
Removable Carrier Type
04-02-13

lower insulators. Torque
the
spring

clip nuts
to
specification.

2.
Place
the
brake backing plates
in

their normal position
on the
axle

housing.

3.
Install
new
axle shaft
oil
seals

with
the
tool shown
in Fig. 10.
Soak

the
new
seals
in
light weight engine
oil

(SAE
10) for 1/2
hour before install-

ing them. Installation without
use of

the proper tool will distort
the
seal

and cause leakage. Coat
the
outside
edges
of the new oil
seal with
a non-

hardening type
of
sealer such
as Per-

matex
No. 2 or its
equivalent.

4.
Install
the
axle shafts, brake

drums
and
wheels
as
outlined
in Sec-

tion
2.

5.
Attach
the
hydraulic brake line

T fitting
to the
axle housing,
and se-

cure
the
hydraulic brake line
in its re-

tainer
on the
axle housing.

6. Install vent tube
to
brake tube

junction
and
install vent hose
to
vent
tube.

7.
Raise
the
axle housing
and con-

nect
the
shock absorbers.

8. Connect
the
rear
end of the
drive

shaft
to the
axle U-joint flange, align-

ing
the
scribe marks made
on the

drive shaft
end
yoke
and the
axle
U-

joint flange.

9. Fill
the
axle with
the
proper

grade
and
amount
of
lubricant.

10.
Road test
the
vehicle.

MAJOR REPAIR OPERATIONS

DISASSEMBLY
OF

DIFFERENTIAL CARRIER

CONVENTIONAL

DIFFERENTIAL

A disassembled view
of the
rear

axle assembly
is
shown
in Fig. 17.

After mounting
the
carrier
in a

holding fixture, disassemble
the car-

rier
as
outlined
in the
following proce-

dures:

1.
Mark
one
differential bearing

cap
and the
mating bearing support

with punch marks
to
help position
the

parts properly during assembly
of the

carrier. Also, mark
one of the
bearing

adjusting nuts
and the
carrier with

AXLE SHAFT-4725
RETAINER RING-1100
scribe marks
for
proper location
dur-

ing assembly.

2.
Remove
the
adjusting
nut
locks,

bearing caps,
and
adjusting nuts. Then

lift
the
differential case assembly
out

of
the
carrier.

(Remove
the
bearing caps
by tap-

ping
the
caps lightly with
a
soft
mal-

let).

3.
Remove
the
differential bearings

with
the
tools shown
in Fig. 18.

4.
Mark
the
differential case, cover,

and ring gear
for
assembly
in the
orig-

inal position.

5.
Remove
the
bolts that attach
the

ring gear
to the
differential case. Press

the gear from
the
case
or tap it off

with
a
soft-faced hammer.

6. With
a
drift, drive
out the
differ-

AXLE HOUSING-4010

DIFFERENTIAL

PINION SHAFT-4211
ential pinion shaft lock
pin (Fig. 19),

and separate
the
2-piece differential

case.

7.
Drive
out the
pinion shaft with
a

brass drift
(Fig. 20).

8. Remove
the
gears
and
thrust

washers
(Fig. 48).

LIMITED-SLIP DIFFERENTIAL

1.
Remove
the
differential case

from
the
carrier
and
remove
the
bear-

ings from
the
differential case
in the

same manner
as the
conventional
dif-

ferential case.

2.
Place
the
differential case
in a

hydraulic press,
and
apply about
one

ton pressure across
the
case bearing

hubs while removing
the
ring gear
at-

FLAT WASHER (LIMITED SLIP ONLY)

DRIVE GEAR ATTACHING BOLT

DIFFERENTIAL CASE COVER -4206

DIFFERENTIAL PINION GEAR-4215

THRUST WASHER-4230

ADJUSTING NUT-4067

CARRIER HOUSING-4025

DRIVE PINION-4610
PINION BEARING

SPACER-4662

PINION FRONT

BEARING-4621

RING GEAR

PILOT BEARING-4A242

FIG. 17—Rear Axle Disassembled—Typical
PILOT BEARING

RETAINER-4627

PINION REAR

BEARING CUP-4616
DEFLECTOR-4859

PINION RETAINER-4668

SEAL-4676
FLANGE_4858
E1750-Aprocarmanuals.com

04-02-21
Rear Axle
—
Removable Carrier Type
04-02-21

SITION IN WHICH GEARS WERE LAPPED

FIG. 51—Gear
Set
Timing Marks

3.
Center
the
Belleville spring
on

the clutch pack (spring concave-side

facing downward
on the
pack)
to pre-

vent trapping
the
spring between
the

left
and
right handcase
in an
eccentric

position
(Fig. 54).
Improper location

of
the
Belleville spring will cause
ex-

tremely high torque
and
differential

chatter.
Be
sure
the
slots
in the
rabbit

ears
of the
steel plates
are in
proper

alignment.

4.
Carefully
set the
differential case

cover over
the
right hand case
(Fig.

55).
At
this point,
no
force
or
pressure

should
be
applied
to the
cover.
The

cover contains
two 3/16
inch holes
by

which
the
clutch plates
can be
proper-

ly aligned. Insert
the
shank ends
of
two
1/8
inch drill bits into
the
holes,

and work
the
drill bits back-and forth

until
the
plates
are
centered
(Fig. 55).

When
the
clutch plates
are
centered,

the weight
of the
cover will cause
it to

fall into position. Remove
the
drill

bits.

5.
Install
the
ring gear
to
differen-

tial case bolts,
and
tighten them even-

ly
and
alternately across
the
diameter

of
the
ring gear. Tighten
the
bolts
to

specification.

6. Prior
to
installation
of the

limited-slip differential into
the ve-

hicle,
a
differential torque check must

be made. Check
the
torque required
to

rotate
one
side gear while
the
other

side gear
is
held
(Fig. 56). The
initial

PINION GEAR

DIFFERENTIAL

CASE
_
LUBRICATOR

HOLE / CLUTCH HUB

THRUST /

PINION \\WASHERS/

SHAFT
BELLEVILLE SPRING

STEEL
PLATE.

BONDED PLATES

CASE COVER

STEEL PLATES

RING GEAR
SIDE GEARS

LOCK
PIN

E 1738-A
STEEL PLATE THRUST WASHER

E 1189-

FIG. 53—Installing Steel Clutch

Plates
and
Friction Plates

BELLEVILLE SPRING

E 1711-A

FIG.
54
— Belleville
Spring

Installation

breakaway torque required
to
start
the

side gear turning
may
exceed
300 ft-

lbs.
Observe only
the
torque required

for continuous even rotation. There

should
be no
abnormal roughness
or

binding.
In
some instances
the
rotat-

ing torque
may
reach
250
ft-lbs, this

condition
is
acceptable,
if
rotation
is

smooth.
If the
results
of the
bench

check
are not
within specified limits,

internal trouble
may be
present
and

should
be
corrected before installing

the assembly
in the
vehicle. Some

possible torque problems
as
follows:

1/8" DRILL

DIFFERENTIAL

CASE COVER

E 1191-C

FIG. 52—Limited-Slip Differential Assembly
FIG.
55—
Differential Cover

Installationprocarmanuals.com

04-03-06

Rear Axles — Integral Carrier Type

04-03-06

9. Install a new integral nut and

ivasher on the pinion shaft. (Apply a

small amount of lubricant on the

washer side of the nut.)

10.
Hold the flange with the tool

shown in Fig. 9 while the nut is being

tightened.

11.
Tighten the pinion shaft nut,

rotating the pinion occasionally to in-

sure proper bearing seating, (Fig. 6)

and take frequent preload readings

until the preload is at the original rec-

orded reading established in step 3.

12.
After original preload has been

reached, tighten the pinion nut slowly,
until an additional preload of 6 to 12

in-lbs has been added.

The preload should not exceed the

amount shown above, or bearing fail-

ure may result.

Under no circumstances should the

pinion nut be backed off to lessen pre-

load. If this is done, a new pinion

bearing spacer must be installed. (In

addition, the U-joint flange must

never be hammered on, or pneumatic-

-tools used.)

13.
Remove the oil seal replacer

tool from the transmission extension
housing. Install the front end of the

drive shaft on the transmission output

shaft.

14.
Connect the rear end of the

drive shaft to the axle U-joint flange,

aligning the scribe marks made on the

drive shaft end yoke and the axle U-

joint flange (Fig. 14).

15.
Check the lubricant level. Make

sure the axle is in running position.

Add whatever amount of specified lu-

bricant is required to reach the lower

edge of the filler plug hole, located in

the carrier casting or housing cover.

REMOVAL AND INSTALLATION

REAR AXLE HOUSING

REMOVAL

1.
Raise the vehicle and support it

with safety stands under the rear

frame member.

2.
Drain the lubricant from the

axle.

3.
Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position of the

drive shaft at assembly (Fig. 14). Dis-

connect the drive shaft at the drive

pinion flange.

4.
Disconnect the lower end of the

shock absorbers.

5.
Remove the wheels, brake drums

and both axle shafts as outlined in the

foregoing Section 2.

6. Remove vent hose front vent

tube (Corbin clamp) and remove vent

tube from brake tube junction and

axle housing.

7.
Remove the hydraulic brake T-
fitting from the axle housing. Do not

open the hydraulic brake system lines.

Remove the hydraulic brake line from

its retaining clip on the axle housing.

8. Remove both axle shaft oil seals

with the tools shown in Fig. 8.

9. Remove both brake backing

plates from the axle housing and sus-

pend them above the housing with me-

chanic's wire. The hydraulic brake

SCRIBE MARKS

5/16-24

4 REQ'D.

12-15
LB.
FT.

U-BOLT - 4529 2 REQ'D.

E 1783-A

FIG. 14—Drive Shaft-to-Axle

U-Joint
Connection

El231-A

FIG. 73—Rear Axle Installation—Typical
lines and the parking brake cables are

still attached to the brake carrier

plates.

10.
Support the rear axle housing

on a jack, and then remove the spring

clip nuts. Remove the spring clip

plates (Fig. 13)

11.
Lower the axle housing and re-

move it from under the vehicle.

12.
If the axle housing is being re-

placed, transfer all the differential and

pinion parts to the new housing. See

Section 4, Major Repair Operations.

INSTALLATION

1.
Raise the axle housing into posi-

tion so that the spring clip plates can

be installed. On a Montego or Fair-

lane,
position the spring upper insula-

tors and retainers between the axle

housing and springs and install the

lower insulators. Torque the spring

clip nuts to specification.

2.
Place the brake backing plates in

their normal position on the axle

housing. Use new gaskets on each side

of the brake backing plates.

3.
Install new axle shaft oil seals

with the tool shown in Fig. 8. Soak

the new seals in light weight engine oil

(SAE 10) for 1/2 hour before install-

ing them. Installation without use of

the proper tool will distort the seal

and cause leakage. Coat the outside

edges of the new oil seal with a non-

hardening type of sealer such as Per-

matex No. 2 or its equivalent.

4.
Install the axle shafts, brake

drums and wheels as outlined in Sec-

tion 2.

5.
Attach the hydraulic brake line

T fitting to the axle housing, and se-

cure the hydraulic brake line in its re-

tainer on the axle housing.

6. Install vent tube to brake tubeprocarmanuals.com

05-01-01
05-01-01

Clutch
GROUP

5

PART
5-1
PAGE

Drive Shaft 05-01-01

PART
5-2

General Clutch Service 05-02-01
PART
5-3

Clutch

PART
5-4

Specifications
PAGE

05-03-01

05-04-01

PART
5-1
Drive Shaft

COMPONENT INDEX

DESCRIPTION

DRIVE SHAFT ANGLE CHECK

DRIVE SHAFT BALANCE CHECK

DRIVE SHAFT BALANCING

(Single Universal Joint)

DRIVE SHAFT DISASSEMBLY
AND

OVERHAUL

Single Universal Joint — Ford Design

Double Cardan Joint — Dana Design

Double Cardan Joint — Saginaw Design

DRIVE SHAFT REMOVAL
AND

INSTALLATION

DRIVE SHAFT RUNOUT CHECK
MODEL APPLICATION
All
Models

01-01

01-01

01-01

01-02

01-01
Ford
01-04

01-04

N/A

N/A
Mercury
01-04

01-04

N/A

N/A
Meteor
01-04

01-04

N/A

N/A
Cougar
01-04

01-04

N/A

N/A
Fairlane
01-04

01-04

N/A

N/A
Falcon
01-04

01-04

N/A

N/A
Montego
01-04

01-04

N/A

N/A
Mustang
01-04

01-04

N/A

N/A
Lincoln-
Continental
N/A

N/A

01-04

N/A
Thunderbird
N/A

N/A

N/A

01-05
Continental-
Mark
III
N/A

N/A

N/A

01-05

A page number indicates that the item
is for the
vehicle listed
at the
head
of
the column.

N/A indicates that
the
item
is not
applicable
to the
vehicle listed.

DRIVE SHAFT TESTS

DRIVE LINE BALANCE CHECK

If detailed parts
of the
drive shaft

are replaced
and
shaft vibration
is en-

countered after installation, disconnect

the shaft
at the
slip yoke. Rotate
the

slip yoke
180
degrees; then, reconnect

the shaft
to the
slip yoke.
If the
vibra-

tion persists, disconnect
the
shaft
at

the rear axle companion flange.
Ro-

tate
the
companion flange
180
degrees

and reconnect
the
shaft
to the
flange.
DRIVE LINE ANGLE CHECK

Vibration
or
"shudder" which
is no-

ticeable either
on
fast acceleration
or

when coasting, using
the
engine
for a

brake,
may be
caused
by the
rear axle

housing being loose
on the
rear

springs
or by
improper pinion angle.

Refer
to
Group
3,
Part
2 for
pinion

angle checking procedures.
If the
rear

axle U-bolts (Fairlane, Montego,

Mustang, Cougar, Falcon models
only)
are
loose, torque
the
nuts
to

specification.

DRIVE SHAFT RUNOUT CHECK

Using
a
dial indicator, check
the

runout
at
each
end and in the
middle

of
the
driveshaft.
The
rear check

should
be
made
on the
small tube
sec-

tion
of the
shaft between
the
balance

weights
and the
yoke welds. Drive-

shaft runout should
not
exceed 0.035

inch
at any one
point.

DESCRIPTION

The drive shaft
is the
means
of

transferring power from
the
engine,

through
the
transmission,
to the dif-
ferential
in the
rear axle,
and
then
to

the rear wheels.
The
drive shaft incor-

porates
two
universal joints
and a
slip
yoke
(Fig. 1) or two
double cardan

universal joints,
one at
each
end of the

shaft (Figs.
2 and 3).
Each double
procarmanuals.com