AC system FORD MUSTANG 2003 Workshop Manual

9. If an obvious cause for an observed or reported malfunction is found, correct the cause (if
possible) before proceeding to the next step.
10. If the fault is not visually evident, determine the symptom and proceed to the following symptom chart.
Steering System Symptom Definitions
Drift/Pull
Pull is a tugging sensation, felt by the hands on the steering wheel, that must be overcome to keep the
vehicle going straight.
Drift describes what a vehicle with this condition does with hands off the steering wheel.
zA vehicle-related drift/pull, on a flat road, will cause a consistent deviation from the straight-
ahead path and require constant steering input in the opposite direction to counteract the effect.
z Drift/pull may be induced by conditions external to the vehicle (i.e., wind, road camber).
Excessive Steering Wheel Play
Excessive steering wheel play is a condition in which there is too much steering wheel movement
before the wheels move. A small amount of steering wheel free play is considered normal.
Feedback
Feedback is a roughness felt in the steering wheel when the vehicle is driven over rough pavement.
Hard Steering or Lack of Assist
Hard steering or lack of assist is experienced when the steering wheel effort exceeds specifications.
Hard steering can remain constant through the full turn or occur near the end of a turn. It is important
to know the difference between hard steering/lack of assist and binding.
Hard steering or lack of assist can result from either hydraulic or mechanical conditions. It is extremely
important to know if this concern occurs during driving, during very heavy or static parking maneuvers.
Nibble
Sometimes confused with shimmy, nibble is a condition resulting from tire interaction with various road
surfaces and observed by the driver as small rotational oscillations of the steering wheel. Poor Returnability/Sticky Steering Visual Inspection Chart
Mechanical
z
Loose tie- rod ends
z Loose suspension components
z Loose steering column shaft universal joints
z Loose column intermediate shaft bolts
z Steering gear
z Binding or misaligned steering column
z Power steering pump
z Bent or pinched power steering hoses Klj . 4 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Poor returnability and sticky steering is used to describe the poor return of the steering wheel to center
after a turn or the steering correction is completed.
Shimmy
Shimmy, as observed by the driver, is large, consistent, rotational oscillations of the steering wheel
resulting from large, side-
to-side (lateral) tire/wheel movements.
Shimmy is usually experienced near 64 km/h (40 mph), and can begin or be amplified when the tire
contacts pot holes or irregularities in the road surface.
Wander
Wander is the tendency of the vehicle to require frequent, random left and right steering wheel
corrections to maintain a straight path down a level road.
Symptom Chart
Symptom Chart Condition
Possible Sources Action
z Hard Steering or
Lack of Assist z
Seized lower steering
column shaft U- joints. z
INSTALL a new lower
steering column shaft.
REFER to Section 211 - 04 .
z Damaged, fractured
steering column
bearing(s). z
REPAIR the steering
column. REFER to
Section 211 - 04 .
z Power steering pump. zGO to Pump Flow and
Pressure Test
Component Test in
this section.
z Suspension
components. z
REFER to Section 204 - 00 for suspension
system diagnosis and
testing.
z Steering gear internal
leakage. z
GO to Pump Flow and
Pressure Test
Component Test in
this section.
z Excessive Steering
Pump Noise z
Power steering pump. zGO to Pump Flow and
Pressure Test
Component Test in
this section.
z Excessive Steering
Wheel Play z
Damaged, loose, or
worn tie- rod end
(3A130). z
GO to the Steering
Linkage Component
Test.
z Loose, worn or
damaged front wheel
spindle tie- rod (3280). z
GO to the Tie- Rod
Articulation Torque
Component Test.
z Damaged/worn
steering gear. z
INSTALL a new
steering gear. REFER
to Section 211 - 02 .
z Loose, worn or
damaged steering z
INSTALL new
steering column Klj . 5 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

column bearing(s).
bearing(s). REFER to
Section 211 - 04 .
z Loose, worn or
damaged lower
steering column shaft
U-joint(s). z
INSTALL a new lower
steering column shaft.
REFER to Section 211 - 04 .
z Wander zUnevenly loaded or
overloaded vehicle. z
INFORM the
customer of incorrect
vehicle loading.
z Loose, worn or
damaged front wheel
spindle tie- rod. z
GO to the Tie- Rod
Articulation Torque
Component Test.
z Loose, worn or
damaged tie- rod ends. z
GO to the Steering
Linkage Component
Test.
z Loose or damaged
steering gear mounting
bolts. z
INSTALL new or
TIGHTEN bolts.
REFER to Section 211 - 02 .
z Loose lower steering
column shaft U- joint
bolts. z
TIGHTEN the bolts.
REFER to Section 211 - 04 .
z Loose, worn or
damaged lower
steering column shaft
U-joints. z
INSTALL a new lower
steering column shaft.
REFER to Section 211 - 04 .
z Loose, worn or
damaged steering
column bearing(s). z
INSTALL new
steering column
bearings. REFER to
Section 211 - 04 .
z Suspension
components. z
REFER to Section 204 - 00 for suspension
system diagnosis and
testing.
z Drift/Pull zUnevenly loaded or
overloaded vehicle. z
INFORM the
customer of incorrect
vehicle loading.
z Wheel alignment. zCHECK the wheel
alignment. ADJUST
as required. REFER
to Section 204 - 00 .
z Loose, worn or
damaged front wheel
spindle tie- rod. z
GO to the Tie- Rod
Articulation Torque
Component Test.
z Loose, worn or
damaged tie- rod ends. z
GO to the Steering
Linkage Component
Test.
z Suspension
components. z
REFER to Section 204 - 00 for suspension
system diagnosis and
testing.
z The steering gear valve
effort out of balance. z
GO to Steering Gear
Valve Component
Test in this section.
z Check the brake
system for proper z
REFER to Section 206 - 00 . Klj . 6 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

operation.
z Incorrect
frame/underbody
alignment. z
CORRECT as
required. REFER to
Frame Dimension
Manual.
z Feedback zLoose, worn or
damaged front wheel
spindle tie- rod. z
GO to the Tie- Rod
Articulation Torque
Component Test.
z Loose, worn or
damaged tie- rod ends. z
GO to the Steering
Linkage Component
Test.
z Loose or damaged
steering gear insulators
or bolts. z
INSTALL new or
TIGHTEN the
retaining bolts.
REFER to Section 211 - 02 .
z Loose lower steering
column shaft U- joint
bolts. z
TIGHTEN the bolts.
REFER to Section 211 - 04 .
z Loose suspension
bushings, fasteners or
ball joints. z
INSTALL new
suspension
components as
necessary. REFER to
Section 204 - 01 .
z Worn or damaged
steering column
bearing(s). z
INSTALL new
steering column
bearing(s). REFER to
Section 211 - 04 .
z Poor
Returnability/Sticky
Steering z
Binding lower steering
column shaft U- joints. z
INSTALL a new lower
steering column shaft.
REFER to Section 211 - 04 .
z Loose, worn or
damaged front wheel
spindle tie- rod. z
GO to the Tie- Rod
Articulation Torque
Component Test.
z Loose, worn or
damaged tie- rod ends. z
GO to the Steering
Linkage Component
Test.
z Suspension
components. z
REFER to Section 204 - 00 for suspension
system diagnosis and
testing.
z Binding steering
column bearing(s). z
INSTALL new
steering column
bearing(s). REFER to
Section 211 - 04 .
z Shimmy zLoose, worn or
damaged tie- rod end. z
GO to the Steering
Linkage Component
Test.
z Loose, worn or
damaged front wheel
spindle tie- rod. z
GO to the Tie- Rod
Articulation Torque
Component Test.
z Suspension
components. z
REFER to Section 204 - 00 for suspension
system diagnosis and
testing. Klj . 7 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
System Flushing —
CII Power Steering Pump
WARNING: Do not mix oil types. Any mixture or any unapproved oil can lead to seal
deterioration and leaks. A leak can ultimately cause loss of fluid, which can result in a loss of
power steering assist.
1. Remove the fuel pump fuse from the battery junction box.
2. Disconnect the power steering return hose. Plug the reservoir.
3. Attach an extension hose between the power steering return hose and an empty container.
4. Raise the front wheels off the floor. For additional information, refer to Section 100 - 02 .
5. Check the fluid level. If necessary, fill the reservoir to the correct level. zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
6. CAUTION: Do not crank the engine for more than 15 seconds at a time. Allow the
starter to cool for 1 minute before cranking again. Premature starter failure can occur.
CAUTION: Do not hold the steering wheel against the stops for more than three to
five seconds at a time. Damage to the power steering pump will occur.
Turn the steering wheel from stop- to-stop while cranking the engine until the fluid exiting the
power steering return hose is clear of all contamination and foreign material.
zAdd Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent as
needed.
7. Lower the vehicle.
8. Disconnect the extension hose from the power steering return hose. Remove the plug. Attach the power steering return hose to the reservoir.
SECTION 211-
00: Steering System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9.
CAUTION: Do not overfill the reservoir.
Check the fluid level. If necessary, fill the reservoir to the correct level. zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
10. Install the fuel pump fuse.
11. CAUTION: Do not hold the steering wheel against the stops for more than three to
five seconds at a time. Damage to the power steering pump will occur.
Start the engine and turn the steering wheel from stop- to-stop.
12. CAUTION: Do not overfill the reservoir.
NOTE: If the power steering system is noisy and is accompanied by evidence of aerated fluid it
will be necessary to purge the power steering system.
Check the fluid level. If necessary, fill the reservoir to the correct level.
zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent. Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
System Flushing —
CIII Power Steering Pump
WARNING: Do not mix oil types. Any mixture or any unapproved oil can lead to seal
deterioration and leaks. A leak can ultimately cause loss of fluid, which can result in a loss of
power steering assist.
1. Remove the fuel pump fuse from the battery junction box.
2. Disconnect the power steering return hose. Plug the reservoir.
3. Attach an extension hose between the power steering return hose and an empty container.
4. Raise the front wheels off the floor. For additional information, refer to Section 100 - 02 .
5. Check the fluid level. If necessary, fill the reservoir to the correct level. zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
6. CAUTION: Do not crank the engine for more than 15 seconds at a time. Allow the
starter to cool for 1 minute before cranking again. Premature starter failure can occur.
CAUTION: Do not hold the steering wheel against the stops for more than three to
five seconds at a time. Damage to the power steering pump could occur.
Turn the steering wheel from stop- to-stop while cranking the engine until the fluid exiting the
power steering return hose is clear of all contamination and foreign material.
zAdd Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent as
needed.
7. Lower the vehicle.
8. Disconnect the extension hose from the power steering return hose. Remove the plug. Attach the power steering return hose to the reservoir.
SECTION 211-
00: Steering System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9.
CAUTION: Do not overfill the reservoir.
Check the fluid level. If necessary, fill the reservoir to the correct level. zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
10. Install the fuel pump fuse.
11. CAUTION: Do not hold the steering wheel against the stops for more than three to
five seconds at a time. Damage to the power steering pump will occur.
Start the engine and turn the steering wheel from stop- to-stop.
12. CAUTION: Do not overfill the reservoir.
NOTE: If the power steering system is noisy and is accompanied by evidence of aerated fluid it
will be necessary to purge the power steering system.
Check the fluid level. If necessary, fill the reservoir to the correct level.
zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent. Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Purging —CII Power Steering Pump
CAUTION: If the air is not purged from the power steering system correctly, premature
power steering pump failure can result. This condition can occur on pre- delivery vehicles with
evidence of aerated fluid or on vehicles that have had steering component repairs.
1. NOTE: A whine heard from the power steering pump may be caused by air in the system. The
power steering purge procedure must be performed prior to any component repair for which
power steering noise complaints are accompanied by evidence of aerated fluid.
Remove the reservoir cap. Check the fluid level. If necessary, fill the reservoir to the correct
level.
zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
2. Tightly insert the Vacuum Pump stopper into the reservoir.
3. Start the vehicle.
4. Using the special tool, apply maximum vacuum and maintain it for a minimum of three minutes with the engine speed set at idle. SECTION 211-
00: Steering System — General Information 2003 Mustang Workshop Manual Special Tool(s)
Vacuum Pump
416-
D002 (D95L-7559- A) or
Equivalent Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Purging —CIII Power Steering Pump
CAUTION: If the air is not purged from the power steering system correctly, premature
power steering pump failure can result. This condition can occur on pre- delivery vehicles with
evidence of aerated fluid or on vehicles that have had steering component repairs.
1. NOTE: A whine heard from the power steering pump may be caused by air in the system. The
power steering purge procedure must be performed prior to any component repair for which
power steering noise complaints are accompanied by evidence of aerated fluid.
Remove the reservoir cap. Check the fluid level. If necessary, fill the reservoir to the correct
level.
zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
2. Tightly insert the Vacuum Pump stopper into the reservoir.
3. Start the vehicle.
4. Using the special tool, apply maximum vacuum and maintain it for a minimum of three minutes with the engine speed set at idle. SECTION 211-
00: Steering System — General Information 2003 Mustang Workshop Manual Special Tool(s)
Vacuum Pump
416-
D002 (D95L-7559- A) or
Equivalent Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...