belt FORD MUSTANG 2003 Workshop Manual

5. Using the special tool, install the D-
ring bolt.
6. Install the quarter trim panel. For additional information, refer to Section 501 - 05 .
7. The shoulder belt must pass through the belt holder on the top of the seatback.
8. Check the active restraint system for correct operation. Klj . 3 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Retractor —
Front Seat Safety Belt, Convertible
Removal 1. Remove the quarter trim panel (31012). For additional information, refer to Section 501 - 05 .
2. Remove the nut and bolts and safety belt retractor.
Installation
NOTE: Make sure the safety belt is not twisted.
1. The shipping clip must remain attached prior to the installation of the retractor into the vehicle. The clip must be removed after the retractor is installed. 2. Position the safety belt retractor. Install the nut and bolts. SECTION 501-
20A: Safety Belt System 2003 Mustang Workshop Manual Special Tool(s)
Torx Bit, Safety Belt Bolt
501-
010 (T77L-2100- A) Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

3. The shoulder belt must pass through the belt holder on the top of the seatback.
4. Install the quarter trim panel. For additional information, refer to
Section 501 - 05 .
5. Check the active restraint system for correct operation. Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Retractor —
Rear Seat Safety Belt, Coupe
Removal 1. Remove the quarter trim panel (31012) and the angel wing trim. For additional information, refer to Section 501 - 05 .
2. Using the special tool, remove the D- ring bolt.
3. Using the special tool, remove the bolt and the safety belt retractor (611B68).
4. Remove the bolt.
SECTION 501-
20A: Safety Belt System 2003 Mustang Workshop Manual Special Tool(s)
Torx Bit, Safety Belt Bolt
501-
010 (T77L-2100- A) Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Installation
NOTE:
Make sure the safety belt is not twisted when inserting it in the quarter trim panel.
1. Install the bolt.
2. Using the special tool, install the safety belt retractor and the bolt.
3. Using the special tool, install the D- ring bolt. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

4. Install the quarter trim panel (31012) and the angel wing trim. For additional information, refer to
Section 501 - 05 .
5. Make sure the shoulder belt passes through the belt holder on the top of the seatback.
6. Check the active restraint system for correct operation. Klj . 3 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Retractor —
Rear Seat Safety Belt, Convertible
Removal 1. Remove the rear seat cushion.
2. Remove the luggage compartment front lining board (45444).
3. Release the safety belt guide.
4. Using the special tool, remove the safety belt anchor bolt.
5. Using the special tool, remove the bolt and the rear safety belt retractor.
SECTION 501-
20A: Safety Belt System 2003 Mustang Workshop Manual Special Tool(s)
Torx Bit, Safety Belt Bolt
501-
010 (T77L-2100- A) Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Installation
NOTE:
Make sure the safety belt is not twisted when inserting it in the quarter trim panel.
1. Using the special tool, install the bolt and the rear safety belt retractor.
2. Using the special tool, install the safety belt anchor bolt.
3. Install the safety belt guide.
4. Install the luggage compartment front lining board. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

5. Install the rear seat cushion.
6. Make sure the shoulder belt passes through the belt holder on the top of the seatback.
7. Check the active restraint system for correct operation. Klj . 3 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Child Safety Seat Belt —
Tether Anchor
Removal and Installation
Hard top only 1. Remove the package tray. For additional information, refer to Section 501 - 05 .
2. Remove the bolts and the tether anchor bracket.
Convertible only 3. NOTE: Rework the sheet metal to its original condition and structural integrity.
The convertible model tether anchors are part of the sheet metal. zThese are accessed through the trunk by removing the trunk front trim.
Hard top only 4. NOTE: Rework the sheet metal to its original condition and structural integrity.
To install, reverse the removal procedure.
Hard top and convertible 5. Check the restraint system for correct operation.
SECTION 501-
20A: Safety Belt System 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...