steering wheel FORD MUSTANG 2003 User Guide

„
Frequencies have a range of plus or minus 2. A reading of 10 Hz can be displayed as an
8 Hz through 12 Hz.
d. Place the vibration sensor on or near the suspect area outside the vehicle.
e. Continue the road test, driving the vehicle at the speed the symptom occurs, and take another reading.
f. Compare the readings.
„A match in frequency indicates the problem component or area.
„ An unmatched test could indicate the concern is caused by the engine, torque converter,
or engine accessory. Use the EVA in the rpm mode and check if concern is rpm related.
„ Example: A vibration is felt in the seat. Place the sensor on the console. Record the
readings. Place the vibration sensor on the rear axle. Compare the readings. If the
frequencies are the same, the axle is the problem component.
Vibrate Software®
Vibrate Software® ( Rotunda tool number 215- 00003) is a diagnostic aid which will assist in pinpointing
the source of unacceptable vibrations. The engine's crankshaft is the point of reference for vibration
diagnosis. Every rotating component will have an angular velocity that is faster, slower, or the same as
the engine's crankshaft. Vibrate Software® calculates the angular velocity of each component and
graphically represents these velocities on a computer screen and on a printed vibration worksheet.
The following steps outline how Vibrate Software® helps diagnose a vibration concern:
zEnter the vehicle information. Vibrate will do all the calculations and display a graph showing
tire, driveshaft and engine vibrations.
z Print a Vibration Worksheet graph. The printed graph is to be used during the road test.
z Road test the vehicle at the speed where the vibration is most noticeable. Record the vibration
frequency (rpm) and the engine rpm on the worksheet graph. The point on the graph where the
vibration frequency (rpm) reading and the engine rpm reading intersect indicates the specific
component group causing the concern.
„An EVA or equivalent tool capable of measuring vibration frequency and engine rpm will
be needed.
z Provide pictures of diagnostic procedures to aid in testing components.
Combination EngineEAR/ChassisEAR
An electronic listening device used to quickly identify noise and the location under the chassis while
the vehicle is being road tested. The ChassisEARs can identify the noise and location of
damaged/worn wheel bearings, CV joints, brakes, springs, axle bearings or driveshaft carrier bearings.
EngineEAR Basic Unit
An electronic listening device used to detect even the faintest noises. The EngineEARs can detect the
noise of damaged/worn bearings in generators, water pumps, A/C compressors and power steering
pumps. They are also used to identify noisy lifters, exhaust manifold leaks, chipped gear teeth and for
detecting wind noise. The EngineEAR has a sensing tip, amplifier, and headphones. The directional
sensing tip is used to listen to the various components. Point the sensing tip at the suspect component
and adjust the volume with the amplifier. Placing the tip in direct contact with a component will reveal
structure-borne noise and vibrations, generated by or passing through, the component. Various
volume levels can reveal different sounds.
Ultrasonic Leak Detector
The Ultrasonic Leak Detector is used to detect wind noises caused by leaks and gaps in areas where
there is weather- stripping or other sealing material. It is also used to identify A/C leaks, vacuum leaks Klj . 12 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

NOTE:
It may be necessary to have the customer ride along or drive the vehicle to point out the
concern. During the road test, take into consideration the customer's driving habits and the driving
conditions. The customer's concern just may be an acceptable operating condition for that vehicle.
The following is a brief overview of each test in the order in which it appears. A review of this
information helps to quickly identify the most appropriate process necessary to make a successful
diagnosis. After reviewing this information, select and carry out the appropriate test(s), proceeding to
the next step of this process.
zThe Slow Acceleration Test is normally the first test to carry out when identifying an NVH
concern, especially when a road test with the customer is not possible.
z The Heavy Acceleration Test helps to determine if the concern is torque- related.
z The Neutral Coast Down Speed Test helps to determine if the concern is vehicle speed- related.
z The Downshift Speed Test helps to determine if the concern is engine speed- related.
z The Steering Input Test helps to determine how the wheel bearings and other suspension
components contribute to a vehicle speed- related concern.
z The Brake Test helps to identify vibrations or noise that are brake related.
z The Road Test Over Bumps helps isolate a noise that occurs when driving over a rough or
bumpy surface.
z The Engine Run- Up Tests consist of the Neutral Run- Up Test and the Engine Load Test. These
tests help to determine if the concern is engine speed- related.
z The Neutral Run- Up Test is used as a follow- up test to the Downshift Speed Test when the
concern occurs at idle.
z The Engine Load Test helps to identify vibration/noise sensitive to engine load or torque. It also
helps to reproduce engine speed- related concerns that cannot be duplicated when carrying out
the Neutral Run- Up Test or the Neutral Coast Down Test.
z The Engine Accessory Test helps to locate faulty belts and accessories that cause engine
speed- related concerns.
z The Vehicle Cold Soak Procedure helps to identify concerns occurring during initial start- up and
when an extended time lapse occurs between vehicle usage.
Slow Acceleration Test
To carry out this test, proceed as follows:
zSlowly accelerate to the speed where the reported concern occurs. Note the vehicle speed, the
engine rpm and, if possible, determine the vibration frequency.
z Attempt to identify from what part of the vehicle the concern is coming.
z Attempt to identify the source of the concern.
z Proceed as necessary.
Heavy Acceleration Test
To carry out this test, proceed as follows:
zAccelerate hard from 0- 64 km/h (0-40 mph).
z Decelerate in a lower gear.
z The concern is torque related if duplicated while carrying out this test.
z Proceed as necessary. Klj . 6 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Neutral Coast Down Speed Test
To carry out this test, proceed as follows:
zDrive at a higher rate of speed than where the concern occurred when carrying out the Slow
Acceleration Test.
z Place the transmission in NEUTRAL and coast down past the speed where the concern occurs.
z The concern is vehicle speed- related if duplicated while carrying out this test. This eliminates
the engine and the torque converter as sources.
z If the concern was not duplicated while carrying out this test, carry out the Downshift Speed
Test to verify if the concern is engine speed related.
z Proceed as necessary.
Downshift Speed Test
To carry out this test, proceed as follows:
zShift into a lower gear than the gear used when carrying out the Slow Acceleration Test.
z Drive at the engine rpm where the concern occurs.
z The concern is engine speed related if duplicated while carrying out this test. This eliminates the
tires, wheels, brakes and the suspension components as sources.
z If necessary, repeat this test using other gears and NEUTRAL to verify the results.
z Proceed as necessary.
Steering Input Test
To carry out this test, proceed as follows:
zDrive at the speed where the concern occurs, while making sweeping turns in both directions.
z If the concern goes away or gets worse, the wheel bearings, hubs, U- joints (contained in the
axles of 4WD applications), and tire tread wear are all possible sources.
z Proceed as necessary.
Brake Test
To carry out this test, proceed as follows:
zWarm the brakes by slowing the vehicle a few times from 80–32 km/h (50–20 mph) using light
braking applications. At highway speeds of 89–97 km/h (50– 60 mph), apply the brake using a
light pedal force.
z Accelerate to 89–97 km/h (55–60 mph).
z Lightly apply the brakes and slow the vehicle to 30 km/h (20 mph).
z A brake vibration noise can be felt in the steering wheel, seat or brake pedal. A brake noise can
be heard upon brake application and diminish when the brake is released.
Road Test Over Bumps
To carry out this test, proceed as follows: Klj . 7 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

„
Loudness proportional to vehicle speed. Low- frequency noise at high
speeds, noise and loudness increase with speed. GO to Symptom Chart —
Driveline Noise/Vibration .
„ A low- pitched noise (drumming). GO to Symptom Chart — Engine
Noise/Vibration .
„ Vibration occurs at a particular speed (mph) regardless of acceleration or
deceleration. GO to Symptom Chart — Tire Noise/Vibration .
„ Noise varies with wind/vehicle speed and direction. GO to Symptom Chart — Air Leak and Wind Noise .
„ Related to engine speed.
„Noise varies with engine rpm. GO to Symptom Chart — Engine
Noise/Vibration .
„ Vibration occurs at a particular speed (mph) regardless of engine speed
(rpm).
2. Acceleration
„Wide open throttle (WOT)
„Engine induced contact between components. Inspect and repair as
necessary.
„ Noise is continuous throughout WOT. Exhaust system or engine ground
out. GO to Symptom Chart — Engine Noise/Vibration .
„ Light/moderate acceleration
„Tip- in moan. Engine/exhaust noise. GO to Symptom Chart — Engine
Noise/Vibration .
„ Knock-type noise. GO to Symptom Chart — Engine Noise/Vibration .
„ Driveline shudder. GO to Symptom Chart — Driveline Noise/Vibration .
„ Engine vibration. GO to Symptom Chart — Engine Noise/Vibration .
3. Turning noise. GO to Symptom Chart — Steering Noise/Vibration .
4. Braking
„Clicking sound is signaling ABS is active. Acceptable ABS sound.
„ A continuous grinding/squeal. GO to Symptom Chart — Brake Noise/Vibration .
„ Brake vibration/shudder. GO to Symptom Chart — Brake Noise/Vibration .
5. Clutching
„A noise occurring during clutch operation. GO to Symptom Chart — Transmission
(Manual) and Transfer Case Noise/Vibration .
„ Vibration. GO to Symptom Chart — Transmission (Manual) and Transfer Case
Noise/Vibration .
6. Shifting
„Noise or vibration condition related to the transmission (automatic). GO to
Symptom Chart — Transmission (Automatic) Noise/Vibration .
„ Noise or vibration related to the transmission (manual). GO to Symptom Chart —
Transmission (Manual) and Transfer Case Noise/Vibration .
7. Engaged in four- wheel drive. GO to Symptom Chart — Transmission (Manual) and
Transfer Case Noise/Vibration .
8. Cruising speeds
„Accelerator pedal vibration. GO to Symptom Chart — Engine Noise/Vibration .
„ Driveline vibration. GO to Symptom Chart — Driveline Noise/Vibration .
„ A shimmy or shake. GO to Symptom Chart — Tire Noise/Vibration .
9. Driving at low/medium speeds Klj . 11 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

high idle during the
first cold start of the
day
lifter/lash
adjuster).
z A continuous, speed-
dependent rattle from
the engine — occurs
during idle or high idle
during the first cold
start of the day and
disappears as the
engine warms up z
Piston noise or
valvetrain noise
(bled down
lifter/lash
adjuster). z
Go To Pinpoint Test G .
z Idle vibration—a low-
frequency vibration (5-
20 Hz) or mild shake
that is felt through the
seat/floorpan z
Cylinder misfire. zUsing a scan tool, CHECK
the ignition system. CARRY
OUT a cylinder power test.
REFER to Section 303 - 00 .
z Engine or
torque
converter out of
balance. z
VERIFY the torque
converter to crankshaft pilot
clearance is correct,
REPAIR as necessary. RE-
INDEX the torque converter
on the flex plate by 120° on
a 3 bolt converter or 180° for
a 4 bolt converter. REFER to
Section 307 - 01 . RETEST
the vehicle.
z Idle vibration—a high-
frequency vibration
(20–80 Hz) or buzz,
that is felt through the
steering wheel or seat z
Exhaust system
mounts bound
up. z
VERIFY concern occurs at
engine firing frequency.
CHECK that the exhaust
system vibrates at the same
frequency as the engine.
ADD 9– 14 km (20–30 lb.) to
the tail pipe to test, CARRY
OUT Exhaust System Neutralizing in this section.
z Body mounts
loose. z
INSPECT the body mounts.
REPAIR as necessary.
z Power steering
lines grounded
out. z
INSPECT that the power
steering lines are not
contacting the chassis or
each other. REPAIR as
necessary. Symptom Chart—
Squeak and Rattle Condition
Possible Sources Action
z Squeak— heard
inside the vehicle
when
closing/opening
the door z
Insufficient
lubrication on
the door hinge
or check strap. z
LUBRICATE the hinge or check
strap.
z Internal door
components
loose, rubbing or
misaligned. z
CHECK the inside of the door.
TIGHTEN or ALIGN as
necessary. USE the Rotunda
Squeak and Rattle Kit to isolate
any rubbing components.
z Squeak— heard
inside the vehicle
when z
Worn or
damaged glass
run/channel. z
REPAIR or INSTALL a new
glass run/channel. REFER to
Section 501 - 11 . Klj . 31 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

misaligned.
screws. REPAIR as necessary.
z Loose interior
component or
trim. z
CARRY OUT a "touch test".
ELIMINATE the noise by
pressing or pulling on interior
trim and components. USE the
Rotunda Squeak and Rattle Kit
to isolate any rattling/squeaking
components.
z Squeak or rattle—
noise with a
vibration concern z
Damaged or
worn body
mounts. z
INSPECT the upper and lower
absorbers and washers for
damage or wear. CHECK the
body mount brackets for
damage. CHECK the nuts and
bolts are tightened to
specifications. TIGHTEN as
necessary.
z Damaged or
worn sub- frame
mounts. z
INSPECT the upper and lower
absorbers for damage or wear.
CHECK the sub- frame for
damage. CHECK the nuts and
bolts are tightened to
specifications. TIGHTEN as
necessary. Symptom Chart—
Steering Noise/Vibration Condition
Possible Sources Action
z Steering grunt or
shudder — occurs
when turning into
or out of a turn at
low speeds
(temperature
sensitive) z
Steering gear or power
steering hoses. z
GO to Steering Gear
Grunt/Shudder Test
component test in this
section.
z Steering System
clonk— hydraulic
knocking sound z
Air in the steering
hydraulic system. z
CHECK for leaks in the
system. PURGE the air
from the system.
REFER to Section 211 -
00 .
z Power steering
pump moan —
loud humming
noise occurs when
the steering wheel
is rotated to the
stop position.
Produces a 120-
600 Hz frequency
that changes with
rpm z
Power steering hose
grounded out to
chassis. z
INSPECT the power
steering hoses. REPAIR
as necessary.
z Aerated fluid. zCHECK for leaks in the
system. PURGE the air
from the system.
REFER to Section 211 -
00 .
z Steering gear isolators. zINSPECT the isolators
for wear or damage.
REPAIR as necessary.
z Low fluid. zCHECK the fluid level. Klj . 33 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REFILL as necessary.
z Power steering pump
brackets loose or
misaligned. z
CHECK bolts, brackets
and bracket alignment.
TIGHTEN bolts to
specification. REPAIR
or INSTALL new
brackets as necessary.
REFER to Section 211 -
02 .
z Steering gear clunk
— occurs only
while cornering
over a bump (can
be temperature
sensitive) z
Steering gear. zINSPECT the steering
gear for loose mounting
bolts. TIGHTEN as
necessary. REFER to
Section 211 - 02 .
z Feedback (rattle,
chuckle or
knocking noise in
the steering gear)
— a condition
where roughness is
felt in the steering
wheel when the
vehicle is driven
over rough
surfaces z
Column
intermediate/flexible
shaft joints damaged or
worn. z
INSTALL a new
intermediate/flexible
shaft. REFER to Section 211 - 04 .
z Loose, damaged or
worn tie- rod ends. z
TIGHTEN the nuts to
specification or
INSTALL new tie- rod
ends as necessary.
REFER to Section 211 -
02 .
z Steering gear
insulators or mounting
bolts loose or
damaged. z
TIGHTEN the bolts or
INSTALL new bolts as
necessary. REFER to
Section 211 - 02 .
z Steering column
intermediate shaft bolts
are loose. z
TIGHTEN the bolts to
specification. REFER to
Section 211 - 04 .
z Steering column
damaged or worn. z
REPAIR or INSTALL a
new steering column as
necessary. REFER to
Section 211 - 04 .
z Loose suspension
bushings, bolts or ball
joints. z
INSPECT the
suspension system.
TIGHTEN or INSTALL
new components as
necessary. REFER to
Section 204 - 01 .
z Feedback (nibble
at the steering
wheel) — a
condition where
slight rotational
movement is felt in
the steering wheel
when the vehicle is
driven over rough
or grooved z
Lateral runout in the
tire or wheel. z
GO to Pinpoint Test H . Klj . 34 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

surfaces
zYoke spring in the
steering gear. z
CHECK TSBs for
revised yoke spring for
applicable vehicles.
z Accessory drive
belt squeal/chirp—
when rotating the
steering wheel
from stop to stop z
Loose or worn
accessory drive belt. z
ADJUST or INSTALL a
new accessory belt as
necessary. REFER to
Section 303 - 05 .
z Power steering
gear hiss z
Steering column
intermediate/flexible
shaft- to-steering gear
is binding or
misaligned. z
REPAIR or INSTALL a
new
intermediate/flexible
shaft as necessary.
REFER to Section 211 -
04 .
z Grounded or loose
steering column boot at
the dash panel. z
REPAIR as necessary.
z Damaged or worn
steering gear input
shaft and valve. z
REPAIR or INSTALL a
new steering gear as
necessary. REFER to
Section 211 - 02 .
z Steering column
rattle z
Loose bolts or
attaching brackets. z
TIGHTEN the bolts to
specifications.
z Loose, worn or
insufficiently lubricated
column bearings. z
LUBRICATE or
INSTALL new steering
column bearings as
necessary. REFER to
Section 211 - 04 .
z Steering shaft
insulators damaged or
worn. z
INSTALL new
insulators. REFER to
Section 211 - 04 .
z Intermediate/flexible
shaft compressed or
extended. z
INSPECT the rubber
spider coupling for
damage. INSTALL a
new
intermediate/flexible
shaft. REFER to Section 211 - 04 .
z Steering column
squeak or cracks z
Insufficient lubricated
steering shaft
bushings. z
LUBRICATE the
steering shaft and shaft
tube seals.
z Loose or misaligned
steering column
shrouds. z
TIGHTEN or ALIGN the
steering column
shrouds.
z Steering wheel rubbing
against steering
column shrouds. z
REPOSITION the
steering column
shrouds.
z Insufficient lubricated
speed control slip ring. z
LUBRICATE the speed
control slip ring.
z Upper or lower bearing
sleeve out of position. z
REPOSITION the
bearing sleeves.
z Power steering
pump noisy z
Incorrect assembly of
components.
z Imperfections on the
outside diameter or z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -Klj . 35 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

acceleration from a slow
speed or stop
assembly
mispositioned. and the rear suspension
for damage or wear.
REPAIR as necessary.
z Incorrect or high
CV joint
operating angle. z
CHECK vehicle ride
height is within limits.
REPAIR as necessary.
z Damaged or
worn front
suspension
components. z
CHECK for a loose
stabilizer bar, damaged
or loose strut/strut
bushings or loose or
worn ball joints.
INSPECT the steering
linkage for wear or
damage. REPAIR or
INSTALL new
components as
necessary.
z Shimmy—most
noticeable on
coast/deceleration. Also
hard steering condition z
Excessive
positive caster. z
CHECK the caster
alignment angle.
CORRECT as
necessary. REFER to
Section 204 - 00 .
Symptom Chart—
Tire Noise/Vibration Condition
Possible Sources Action
z Tire noise— hum/moan
at constant speeds z
Abnormal wear
patterns. z
SPIN the tire and CHECK
for tire wear. INSTALL a
new tire as necessary.
INSPECT for
damaged/worn suspension
components. CARRY OUT
wheel alignment.
z Tire noise— noise tone
lowers as the vehicle
speed is lowered z
Out-of- balance
tire. z
BALANCE the tire and
road test. INSTALL a new
tire as necessary. REFER
to Section 204 - 04 .
z Tire noise — ticking
noise, changes with
speed z
Nail puncture or
stone in tire
tread. z
INSPECT the tire. REPAIR
as necessary.
z Wheel and tire—
vibration and noise
concern is directly
related to vehicle
speed and is not
affected by
acceleration, coasting
or decelerating z
Damaged or
worn tire. z
Go To Pinpoint Test J .
z Tire wobble or
shudder — occurs at
lower speeds z
Damaged wheel
bearings. z
SPIN the tire and CHECK
for abnormal wheel
bearing play or roughness.
ADJUST or INSTALL new
wheel bearings as
necessary. REFER to
Section 204 - 01 .
z Damaged wheel. zINSPECT the wheel for
damage. INSTALL a new
wheel as necessary.
REFER to Section 204 -Klj . 38 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

01 .
z Damaged or
worn suspension
components. z
INSPECT the suspension
components for wear or
damage. REPAIR as
necessary.
z Loose wheel
nuts. z
CHECK the wheel nuts.
TIGHTEN to specification.
REFER to Section 204 -
04 .
z Damaged or
uneven tire wear. z
SPIN the tire and CHECK
for abnormal tire wear or
damage. INSTALL a new
tire as necessary. REFER
to Section 204 - 04 .
z Tire shimmy or
shake— occurs at
lower speeds z
Wheel/tire out of
balance. z
BALANCE the wheel/tire
assembly.
z Uneven tire wear. zCHECK for abnormal tire
wear. INSTALL a new tire
as necessary. REFER to
Section 204 - 04 .
z Excessive radial
runout of wheel
or tire. z
CARRY OUT a radial
runout test of the wheel
and tire. INSTALL a new
tire as necessary. REFER
to Section 204 - 04 .
z Worn or
damaged wheel
studs or
elongated stud
holes. z
INSPECT the wheel studs
and wheels. INSTALL new
components as necessary.
REFER to Section 204 - 01
for the front wheels or
Section 204
- 02 for the rear
wheels.
z Excessive lateral
runout of the
wheel or tire. z
CARRY OUT a lateral
runout test of the wheel
and tire. CHECK the
wheel, tire and hub.
REPAIR or INSTALL new
components as necessary.
z Foreign material
between the
brake disc and
hub or in the
brake disc fins. z
CLEAN the mounting
surfaces of the brake disc
and hub. CHECK the
brake disc fins for material.
z High speed shake or
shimmy—occurs at
high speeds z
Excessive wheel
hub runout.
z Damaged or
worn tires.
z Damaged or
worn wheel
bearings.
z Worn or
damaged
suspension or
steering linkage
components.
z Brake disc or
drum imbalance. z
Go To Pinpoint Test K . Klj . 39 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...