FORD MUSTANG 2003 Workshop Manual

8. Install the transmission filter and pan. For additional information, refer to
Fluid Pan, Gasket and Filter in this section. Klj . 6 ba
72003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

Klj . 7 ba
72003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Extension Housing Seal and Gasket
Removal 1. Drain the transmission fluid. For additional information, refer to Fluid Pan, Gasket and Filter in
this section.
2. NOTE: The output shaft and driveshaft are a balanced assembly.
Mark the driveshaft flange and the rear companion flange for correct alignment during
assembly.
3. Remove the four driveshaft bolts.
SECTION 307-
01: Automatic Transaxle/Transmission 2003 Mustang Workshop Manual Special Tool(s)
Slide Hammer
100-
001 (T50T-100- A) Installer, Transmission
Extension Housing Fluid Seal
308-
002 (T61L-7657- A) Remover, Transmission Fluid
Seal
307-
048 (T74P-77248- A) Klj . 1 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

4. Separate the driveshaft from the transmission.
5. Use a high-
lift transmission jack to support the transmission.
6. Remove the transmission crossmember bolts.
7. Remove the transmission mount and crossmember.
8. Using the special tools, remove the extension housing seal. Klj . 2 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

9. Lower the transmission to access the extension housing bolts.
10. Remove the extension housing and gasket. 1. Remove the bolts and the nuts.
2. Remove the extension housing and gasket.
Installation 1. Install the extension housing and gasket. 1. Install the extension housing gasket and housing.
2. Install the bolts and the nuts.
2. Using the special tool, install the new extension housing seal. Klj . 3 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

3. Raise and position the transmission.
4. Install the transmission mount and crossmember.
5. Install the transmission crossmember bolts.
6. Remove high-
lift transmission jack.
7. NOTE: The output shaft and the driveshaft are a balanced assembly.
Install the driveshaft. zAlign the yellow dots and position the driveshaft on the transmission.
z Install the driveshaft. Klj . 4 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

8.
NOTE: To maintain driveshaft balance, align the marks made during disassembly for the rear
axle flange and the driveshaft yoke.
Install the four bolts.
9. Install the filter and pan. For additional information, refer to Fluid Pan, Gasket and Filter in this
section. Klj . 5 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Electronic Pressure Control (EPC) Solenoid
Removal 1. Remove the manual control lever. For additional information, refer to Manual Control Lever Shaft and Seal in this section.
2. CAUTION: Do not pull on the molded lead frame. This may cause damage to the
connector ends. Carefully pry up on the locking tabs to disconnect the solenoids.
Disconnect the molded lead frame from the solenoids.
Disconnect the molded lead frame from the solenoids. 1. Disconnect the shift solenoid SSA and SSB.
2. Disconnect the torque converter clutch (TCC).
3. Disconnect the electronic pressure control (EPC) solenoid.
4. Disconnect the bulkhead inter- connector.
3. Remove the EPC solenoid. 1. Remove the bolt and EPC solenoid bracket.
SECTION 307-
01: Automatic Transaxle/Transmission 2003 Mustang Workshop Manual Special Tool(s)
Gauge, Transmission Solenoid
Connectors
307-426 Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

2. Remove the EPC solenoid.
Installation 1. Install the EPC solenoid. 1. Install the EPC solenoid.
2. Install the EPC solenoid bracket and bolt.
2. Inspect the lead frame for damage. zUsing the special tool, check all lead frame solenoid connections. The gauge should fit
tightly and not fall out after being inserted.
z If the special tool passes through any lead frame connector pins or does not feel like it
makes a good contact, install a new lead frame.
3. Connect the molded lead frame to the solenoids. zConnect the bulkhead inter- connector by pressing it in place by hand and fully seating
the connector in place.
z Connect the EPC solenoid by pressing it in place by hand and fully seating the connector
in place. Make sure that the terminals pass fully through the connector slots.
z Connect the TCC by pressing it in place by hand and fully seating the connector in place. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

Make sure that the terminals pass fully through the connector slots.
z Connect the shift solenoid SSA and SSB by pressing it in place by hand and fully seating
the connector in place. Make sure that the terminals pass fully through the connector
slots.
4. Install the manual control lever. For additional information, refer to Manual Control Lever Shaft and Seal in this section. Klj . 3 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...