FORD MUSTANG 2003 Workshop Manual

IN-
VEHICLE REPAIR
Manual Control Lever Shaft and Seal
Removal 1. Drain the transmission fluid and remove the fluid pan and filter. For additional information, refer to Fluid Pan, Gasket and Filter in this section.
2. Disconnect the digital transmission range (TR) sensor electrical connector.
3. Disconnect the transmission shift linkage.
4. Remove the digital TR sensor.
SECTION 307-
01: Automatic Transaxle/Transmission 2003 Mustang Workshop Manual Special Tool(s)
Installer, Shift Shaft Fluid Seal
307-
050 (T74P-77498- A) Alignment Gauge, TR Sensor
307-
351 (T97L-70010- A) Klj . 1 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

z
Remove the bolts.
z Remove the digital TR sensor.
5. Remove the manual control valve detent lever spring. 1. Remove the bolt.
2. Remove the manual control valve detent lever spring.
6. NOTE: Use a shop cloth to protect the transmission case surface.
Remove the manual lever shaft retaining pin.
7. Remove the nut and slide the manual control lever shaft out of the case. Klj . 2 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

8. Remove the parking lever actuating rod.
1. Remove the manual valve detent lever.
2. Remove the parking lever actuating rod.
9. CAUTION: Use care not to damage the manual control lever shaft bore. New seal
may leak due to damage to the bore.
Remove the manual control lever shaft seal.
Installation 1. Using the special tool, install the manual control lever seal. Klj . 3 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

2. Install the parking lever actuating rod.
1. Install the parking lever actuating rod.
2. Install the manual valve detent lever.
3. Install the manual control lever shaft. 1. Install the manual control lever shaft.
2. Install the nut.
3. Install the manual lever shaft retaining pin.
4. Install the manual valve detent lever spring. 1. Position the manual valve detent lever spring.
2. Install the bolt. Klj . 4 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

5. Install the digital TR sensor.
1. Install the digital TR sensor.
2. Loosely install the bolts.
6. NOTE: The tool is designed to fit snug.
NOTE: Manual shift lever shaft must be in the neutral position.
Using the special tools, align the digital TR sensor slots.
7. Tighten the bolts. Klj . 5 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

8. With manual lever in overdrive, connect the shift control cable.
9. Install the digital TR sensor electrical connector.
10. Install the filter and transmission fluid pan. For additional information, refer to Fluid Pan, Gasket and Filter in this section. Klj . 6 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Digital Transmission Range (TR) Sensor
Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414 - 01 .
2. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
3. Disconnect the connector.
4. Disconnect the manual lever shift control cable.
5. Remove the digital TR bolts and the TR sensor.
SECTION 307-
01: Automatic Transaxle/Transmission 2003 Mustang Workshop Manual Special Tool(s)
Alignment Gauge, TR Sensor
307-
351 (T97L-70010- A) Klj . 1 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

Installation
1. Install the digital TR sensor and loosely install the bolts.
2. NOTE: The tool is designed to fit snugly.
NOTE: Manual shift lever shaft must be in the neutral position.
Using the special tool, align the digital TR sensor slots.
3. Tighten the bolts. Klj . 2 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

4. With the manual lever in overdrive connect the shift lever control cable.
5. Install the digital TR sensor electrical connector.
6. Lower the vehicle.
7.
NOTE: When the battery is disconnected and reconnected, some abnormal driving symptoms
may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven
16 km (10 miles) or more to relearn the strategy.
Connect the battery ground cable. Klj . 3 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

Klj . 4 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...