belt FORD MUSTANG 2003 Owner's Manual

PINPOINT TEST D: EXCESSIVE/ERRATIC BRAKE PEDAL TRAVEL
PINPOINT TEST E: HYDRO-
BOOST, NO POWER ASSIST 4481 kPa (510-
650 psi)? INSTALL a new proportioning valve.
RETEST for normal operation.
Test Step Result / Action to Take
D1 CHECK FOR SPONGY PEDAL
z
Key in ON position.
z Operate the brake pedal and note pedal feel.
z Does the pedal feel spongy? Yes
BLEED the brake system. REFER to
Bleeding —
System in this section.
RETEST for normal operation.
No
GO to D2 .
D2 CHECK THE BRAKE PEDAL
z
Inspect the brake pedal and bracket for
binding, obstruction or damage.
z Is the brake pedal OK? Yes
GO to
D3 .
No
REPAIR or INSTALL a new brake pedal as
necessary. RETEST for normal operation. D3 CHECK THE BRAKE COMPONENTS
z
Inspect the calipers bolts, anchor plate bolts
and anti- rattle springs for binding, damage,
contamination and correct installation.
z Are the bolts and springs OK? Yes
GO to
D4 .
No
REPAIR or INSTALL new components as
necessary. RETEST for normal operation. D4 CHECK THE BOOSTER AND MASTER
CYLINDER z
Check the power brake booster and brake
master cylinder for correct installation and
correct push rod adjustment. Refer to
Section 206 - 06 and to Section 206 - 07 .
z Are the power brake booster and the
brake master cylinder OK? Yes
INSPECT the front wheel bearings for
wear, damage and correct installation and
the rear axle end play. CORRECT as
necessary. RETEST for normal operation.
No
CORRECT as necessary. RETEST for
normal operation.
Test Step Result / Action to Take
E1 CHECK FLUID LEVEL IN POWER STEERING
PUMP z
Check fluid level in power steering pump.
z Is level within specification? Yes
GO to
E2 .
No
CHECK for leakage of power steering
fluid. ADD fluid as necessary. E2 CHECK ACCESSORY DRIVE BELT Klj . 10 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST F: HYDRO-
BOOST ERRATIC OPERATION, STICKS,
BINDS OR GRABS z
Check accessory drive belt tension and
condition. Refer to Section 303 - 05 .
z Is the accessory drive belt OK? Yes
GO to
E3 .
No
INSTALL a new accessory drive belt.
REFER to Section 303 - 05 .
E3 CHECK POWER STEERING HOSES
z
Check power steering pressure hoses, power
steering gear pressure hoses and power
steering return hose for cracks or leaks.
z Do power steering pressure hose, power
steering gear hose and power steering
return hose check OK? Yes
GO to
E4 .
No
INSTALL new hoses as necessary.
REFER to Section 211 - 00 .
E4 CHECK BRAKE PEDAL LINKAGE
z
Check brake pedal linkage for binding or
sticking operation.
z Does pedal linkage check OK? Yes
GO to
E5 .
No
INSTALL new pedal linkage as necessary.
REFER to Section 206 - 06 .
E5 CHECK POWER STEERING PUMP SPEED
z
Check engine idle speed against
specifications.
z Is engine idle speed OK? Yes
GO to
E6 .
No
SET engine idle speed to specification.
REFER to Powertrain Control/Emissions
Diagnosis (PC/ED) manual. E6 CHECK FOR PLUGGED RETURN HOSE
z
NOTE: The return hose from the oil cooler to
the power steering reservoir has an in- line
filter in the hose.
z Disconnect power steering return hose from
power steering fluid cooler and power
steering pump reservoir.
z Pass air through hose from the oil cooler end.
z Is hose plugged? Yes
INSTALL a new power steering return
hose.
No
GO to
E7 .
E7 CHECK POWER STEERING PUMP FLOW
AND RELIEF z
Test power steering pump for correct flow
and relief pressure. Refer to Section 211 - 00 .
z Is power steering pump operating
correctly? Yes
INSTALL a new power brake hydro-
boost
unit. REFER to Section 206 - 07 .
No
INSTALL a new power steering pump.
REFER to Section 211 - 02 .
Test Step Result / Action to
Take F1 CHECK SUPPLY HOSE
z
Check for obstructions in power steering return hose and Yes Klj . 11 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

1. Verify the customer concern by operating the steering system.
2. Inspect Tires
zCheck the tire pressure. Refer to the Vehicle Certification (VC) label.
z Verify that all tires are sized to specification.
z Check the tires for damage or uneven wear.
3. Belt and Tensioner Check zRefer to Section 303 - 05 for diagnosis and testing of the accessory drive system.
4. Fluid Level Check zVerify that the power steering fluid level is within the appropriate indicated range, hot for
the 3.8L engine and cold for the 4.6L engine. Add Motorcraft MERCON® Multi- Purpose
ATF XT -2-QDX or MERCON® equivalent.
5. Air Bleeding zVerify that there is no air in the power steering system. Run the engine (6007) until it
reaches normal operating temperature. Turn the steering wheel to the left and right
several times without hitting the stops. If any air bubbles are present, refer to Purging —
CII Power Steering Pump or
Purging — CIII Power Steering Pump in this section.
External Leak Check — Typical Power Rack-and-Pinion Steering Gear Klj . 2 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Component Tests
Steering Linkage
1. NOTE: Excessive vertical motion of the studs relative to the sockets may indicate excessive
wear.
With the parking brake applied, perform the following:
zHave an assistant rotate the steering wheel back and forth 360 degrees and watch for
relative motion of the studs in the tie- rod end ball sockets.
z Watch for loose steering gear mounting.
2. Another method is to raise the front wheels (1007) off the ground, grasp the wheel at the front and rear and watch for excessive play or binding in the joints while trying to steer the wheels.
3. Install new steering components as necessary. For additional information, refer to the appropriate Group 2 steering section.
Turning Effort Test
NOTE: Make sure that the front wheels are properly aligned and the tire pressure is correct before
checking the effort.
1. Park the vehicle on dry concrete and set the parking brake.
2. Insert a thermometer into the power steering pump reservoir.
3. CAUTION: Do not hold the steering wheel against the stops for more than three to
five seconds at a time. Damage to the power steering pump will occur.
Idle the engine for two to three minutes. Turn the steering wheel from stop- to-stop several times
to warm the fluid to 50- 60°C (122-140°F).
4. With the engine running, attach special tool 211- 034 (T74P-3504-Y) to the rim of the steering
wheel.
5. Measure the pull required to turn the steering wheel one complete revolution in each direction. Refer to Steering Wheel Turning Effort under General Specifications in this section.
Pump Flow and Pressure Test WARNING: Do not touch the flowmeter during the test procedure, or severe burns and
serious injury may occur.
1. CAUTION: Make sure that the connection point will not interfere with any of the
engine accessory drive components or drive belts.
Install special tool 211- F001 (014-00207) at the high pressure port of the power steering pump.
Make sure the power steering analyzer gate valve is fully open. Klj . 8 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Pulley —
CII Pump
Removal 1. Remove the drive belt. For additional information, refer to Section 303 - 05 .
2. Using the special tool, remove the pulley.
Installation 1. Using the special tool, install the pulley.
SECTION 211-
02: Power Steering 2003 Mustang Workshop Manual Special Tool(s)
Pump Pulley Installer
211-
009 (T65P-3A733- C) Pump Pulley Remover
211-
016 (T69L-10300- B) Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2. Install the drive belt. For additional information, refer to
Section 303 - 05 . Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Pulley —
CIII Pump
Removal 1. Remove the drive belt. For additional information, refer to Section 303 - 05 .
2. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
3. Using the special tool, remove the pulley. zInspect the pulley for paint marks in the web area near the hub. If there are two paint
marks, discard and install a new pulley. If there is no paint or one paint mark, use a paint
pencil to mark the web area of the pulley near the hub.
Installation 1. Using the special tool, install a new pulley.
SECTION 211-
02: Power Steering 2003 Mustang Workshop Manual Special Tool(s)
Pump Pulley Replacer
211-
185 (T91P-3A733- A) Pump Pulley Remover
211-
016 (T69L-10300- B) Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2. Install the drive belt. For additional information, refer to
Section 303 - 05 .
3. Lower the vehicle. Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

B1405 Driver Power Window Down
Circuit Short to Battery GEM REFER to
Section 501 - 11 .
B1408 Driver Power Window Up
Circuit Short to Battery GEM REFER to
Section 501 - 11 .
B1410 Driver Power Window Motor
Circuit Failure GEM REFER to
Section 501 - 11 .
B1426 Lamp Safety Belt Circuit Short
to Battery GEM REFER to
Section 413 - 01 .
B1428 Lamp Safety Belt Circuit Failure GEM REFER to
Section 413 - 01 .
B1431 Wiper Brake/Run Relay Circuit
Failure GEM REFER to
Section 501 - 16 .
B1432 Wiper Brake/Run Relay Circuit
Short to Battery GEM REFER to
Section 501 - 16 .
B1434 Wiper Hi/Low Speed Relay Coil
Circuit Failure GEM REFER to
Section 501 - 16 .
B1436 Wiper Hi/Low Speed Relay Coil
Circuit Short to Battery GEM REFER to
Section 501 - 16 .
B1438 Wiper Mode Select Switch
Circuit Failure GEM REFER to
Section 501 - 16 .
B1441 Wiper Mode Select Switch
Circuit Short to Ground GEM REFER to
Section 501 - 16 .
B1446 Wiper Park Sense Circuit
Failure GEM REFER to
Section 501 - 16 .
B1448 Wiper Park Sense Circuit Short
to Battery GEM REFER to
Section 501 - 16 .
B1450 Wiper Wash/Delay Switch
Circuit Failure GEM REFER to
Section 501 - 16 .
B1453 Wiper Wash/Delay Switch
Circuit Short to Ground GEM REFER to
Section 501 - 16 .
B1458 Wiper Washer Pump Motor
Relay Circuit Failure GEM REFER to
Section 501 - 16 .
B1460 Wiper Washer Pump Motor
Relay Coil Circuit Short to Battery GEM REFER to
Section 501 - 16 .
B1462 Safety Belt Switch Circuit
Failure GEM REFER to
Section 413 - 09 .
B1466 Wiper Hi/Low Speed Not
Switching GEM REFER to
Section 501 - 16 .
B1473 Wiper Low Speed Circuit Motor
Failure GEM REFER to
Section 501 - 16 .
B1476 Wiper High Speed Circuit Motor
Failure GEM REFER to
Section 501 - 16 .
B1551 Decklid Release Circuit Failure GEM REFER to
Section 501 - 14B .
B1553 Decklid Release Circuit Short
to Battery GEM REFER to
Section 501 - 14B .
B1555 Ignition Run/Start Circuit
Failure GEM GO to
Pinpoint Test D .
B1687 Lamp Dome Input Circuit Short
to Battery GEM REFER to
Section 417 - 02 .
B2486 LF Side Repeater Lamp Output GEM REFER to
Section 417 - 01 . Klj . 3 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

(PC/ED) manual.
z Damaged valve
tappet or lash
adjuster. z
INSTALL a new valve tappet or
lash adjuster.
z Damaged valve
tappet guide or
valve tappet. z
INSTALL a new valve tappet
guide or valve tappet.
z Burnt or sticking
valve. z
REPAIR or INSTALL a new
valve.
z Weak or broken
valve spring. z
INSTALL a new valve spring.
z Carbon
accumulation in
combustion
chamber. z
ELIMINATE carbon buildup.
z Excessive oil
consumption z
Leaking oil. zREPAIR oil leakage.
z Malfunctioning PCV
system. z
REPAIR or INSTALL new
necessary components.
z Worn valve stem
seal. z
INSTALL a new valve stem seal.
z Worn valve stem or
valve guide. z
INSTALL a new valve and valve
guide.
z Sticking piston
rings. z
REPAIR or INSTALL new piston
rings.
z Worn piston ring
groove. z
INSTALL a new piston and
piston pin.
z Worn piston or
cylinder. z
REPAIR or INSTALL a new
piston or cylinder block.
z Engine noise zLeaking exhaust
system. z
REPAIR exhaust leakage.
z Incorrect drive belt
tension. z
REFER to Section 303 - 05 .
z Malfunctioning
generator bearing. z
Refer to the appropriate section
in Group 414 for the procedure.
z Malfunctioning
water pump
bearing. z
REFER to Section 303 - 03A .
z Malfunctioning or
damaged cooling
system. z
REFER to Section 303 - 03A .
z Malfunctioning or
damaged fuel
system. z
Refer to the appropriate section
in Group 303 for the procedure.
REFER to the Powertrain
Control/Emissions Diagnosis
(PC/ED) manual.
z Loose timing
chain/belt (6268). z
ADJUST or INSTALL a new
timing chain/belt.
z Damaged timing
chain tensioner
(6L266). z
INSTALL a new timing chain
tensioner.
z Excessive main
bearing clearance. z
ADJUST clearance or INSTALL
a new crankshaft main bearing
(6333). Klj . 4 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...