tires FORD MUSTANG 2003 Owner's Manual

operation.
K3 MEASURE THE LATERAL RUNOUT AND THE RADIAL
RUNOUT OF THE FRONT WHEELS ON THE VEHICLE z
Measure the lateral runout and the radial runout of the front
wheels on the vehicle. Refer to Go To Pinpoint Test J .
z Are the measurements within specifications? Yes
GO to
K4 .
No
INSTALL new wheels as
necessary and BALANCE
the assembly. TEST the
system for normal
operation. K4 MEASURE THE LATERAL RUNOUT OF THE FRONT TIRES
ON THE VEHICLE z
Measure the lateral runout of the front tires on the vehicle. Go To Pinpoint Test J .
z Is the runout within specifications? Yes
GO to
K5 .
No
INSTALL new tires as
necessary and BALANCE
the assembly. TEST the
system for normal
operation. K5 MEASURE THE RADIAL RUNOUT OF THE FRONT TIRES
ON THE VEHICLE z
Measure the radial runout of the front tires on the vehicle. Go To Pinpoint Test J .
z Is the runout within specifications? Yes
BALANCE the front wheel
and tire assemblies. If any
tire cannot be balanced,
INSTALL a new tire.
TEST the system for
normal operation.
No
GO to
K6 .
K6 MATCH MOUNT THE TIRE AND WHEEL ASSEMBLY
z
Mark the high runout location on the tire and also on the
wheel. Break the assembly down and rotate the tire 180
degrees (halfway around) on the wheel. Inflate the tire and
measure the radial runout.
z Is the runout within specifications? Yes
BALANCE the assembly.
TEST the system for
normal operation.
No
If the high spot is not
within 101.6 mm (4
inches) of the first high
spot on the tire, GO to
K7
.
K7 MEASURE THE WHEEL FLANGE RUNOUT
z
Dismount the tire and mount the wheel on a wheel balancer.
Measure the runout on both wheel flanges. Go To Pinpoint Test J . Yes
LOCATE and MARK the
low spot on the wheel.
INSTALL the tire,
matching the high spot on
the tire with the low spot
on the wheel. BALANCE
the assembly. TEST the
system for normal
operation. If the condition Klj . 59 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Wheel and tire NVH concerns are directly related to vehicle speed and are not generally affected by
acceleration, coasting or decelerating. Also, out-of-
balance wheel and tires can vibrate at more than
one speed. A vibration that is affected by the engine rpm, or is eliminated by placing the transmission
in NEUTRAL is not related to the tire and wheel. As a general rule, tire and wheel vibrations felt in the
steering wheel are related to the front tire and wheel assemblies. Vibrations felt in the seat or floor are
related to the rear tire and wheel assemblies. This can initially isolate a concern to the front or rear.
Careful attention must be paid to the tire and wheels. There are several symptoms that can be caused
by damaged or worn tire and wheels. Carry out a careful visual inspection of the tires and wheel
assemblies. Spin the tires slowly and watch for signs of lateral or radial runout. Refer to the tire wear
chart to determine the tire wear conditions and actions. Klj . 68 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

For a vibration concern, use the vehicle speed to determine tire/wheel frequency and rpm. Calculate
tire and wheel rpm and frequency by carrying out and following:
zMeasure the diameter of the tire.
z Record the speed at which the vibration occurs.
z Obtain the corresponding tire and wheel rpm and frequency from the Tire Speed and Frequency
Chart.
„If the vehicle speed is not listed, divide the vehicle speed at which the vibration occurs by
16 km/h (10 mph). Multiply that number by 16 km/h (10 mph) tire rpm listed for that tire
diameter in the chart. Then divide that number by 60. For example: a 40 mph vibration
with 835 mm (33 in) tires. 40 ÷ 10 = 4. Multiply 4 by 105 = 420 rpm. Divide 420 rpm by 60
seconds = 7 Hz at 40 mph.
Tire Speed and Frequency Chart Tire
Diameter Tire RPM/Hz Tire RPM/Hz Tire RPM/Hz Tire RPM/Hz
mm (inch) @ 16 km/h (10
mph) @ 80 km/h (50
mph) @ 97 km/h (60
mph) @ 113 km/h (70
mph) 483 (19) 182 910/15 1092/18 1274/21
508 (20) 173 865/14 1038/17 1211/20
533 (21) 165 825/14 990/16 1155/19
560 (22) 158 790/13 948/16 1106/18
585 (23) 151 755/13 906/15 1057/18
610 (24) 145 725/12 870/14 1015/17
635 (25) 139 695/12 834/14 973/16
660 (26) 134 670/11 804/13 938/16
685 (27) 129 645/11 774/13 903/15
710 (28) 124 620/10 744/12 868/14
735 (29) 119 595/10 714/12 833/14
760 (30) 115 575/10 690/11 805/13
785 (31) 111 555/9 666/11 777/13
810 (32) 108 540/9 648/11 756/13
835 (33) 105 525/9 630/10 735/12
864 (34) 102 510/8 612/10 714/12 Klj . 69 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Wheel Bearing Check
1. WARNING: The electrical power to the air suspension system must be shut off prior
to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by
turning off the air suspension switch. Failure to do so can result in unexpected inflation
or deflation of the air springs, which can result in shifting of the vehicle during these
operations.
Raise the vehicle until the front tires are off the floor.
zMake sure the wheels are in a straight forward position.
2. NOTE: Make sure the wheel rotates freely and that the brake pads are retraced sufficiently to
allow free movement of the tire and wheel assembly.
Spin the tire by hand to check the wheel bearings for roughness.
3. Grip each front tire at the top and bottom and move the wheel inward and outward while lifting the weight of the tire off the front wheel bearing.
4. If the tire and wheel (hub) is loose on the spindle, does not rotate freely, or has a rough feeling when spun, carry out one of the following:
1. On vehicles with inner and outer bearings, inspect the bearings and cups for wear or damage. Adjust or install new bearings and cups as necessary.
2. On vehicles with one sealed bearing, install a new wheel hub.
SECTION 100-
04: Noise, Vibration and Harshness 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Suspension System
Inspection and Verification
1. Road test. zVerify the customer's concern by performing a road test on a smooth road.
2. Inspect tires. zCheck the tire pressure with all normal loads in the vehicle and the tires cold. For
additional information, refer to the vehicle certification (VC) label.
z Verify that all tires are sized to specification.
z Inspect the tires for incorrect wear and damage.
3. Inspect chassis and underbody. zRemove any excessive accumulation of mud, dirt or road deposits from the chassis and
underbody.
4. Inspect for aftermarket equipment. zCheck for aftermarket changes to the steering, suspension, wheel and tire components
(such as competition, heavy duty, etc.) The specifications shown in this manual do not
apply to vehicles equipped with aftermarket equipment.
5. Inspect shock absorbers. All vehicles are equipped with gas- pressurized hydraulic shock absorbers. These shock
absorbers are not adjustable or refillable and cannot be repaired.
zOil Leak: A light film of oil (weepage) on the upper portion of the shock absorber is
permissible and is a result or correct shock lubrication. Weepage is a condition in which a
film of oil accumulates on the thin tube (body) and is normally noticed due to the
collection of dust in this area. If shock absorbers exhibit this weepage condition, they are
functional units and new shock absorbers should not be installed. Leakage is a condition
in which the entire shock absorber body is covered with oil and the oil will drip from the
shock absorber onto the pavement. If condition exists:
„Make sure fluid observed is not from sources other than the shock absorber.
„ Install a new shock absorber, if necessary.
z Vehicle Sag: Many times new shock absorbers are installed in an effort to solve a vehicle
sag concern. Shock absorbers by design are hydraulic damping units only and, unlike
suspension springs, do not support any suspension loads. Therefore, installing a new
shock absorber will not correct a vehicle sag concern.
z Installment in Pairs: In the past it was recommended that new shock absorbers be
installed in pairs if one unit became unrepairable. New shock absorbers no longer need
to be installed in pairs when only one unit is not repairable.
SECTION 204-
00: Suspension System — General Information 2003 Mustang Workshop Manual Visual Inspection Chart
Mechanical Klj . 1 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. If an obvious cause for an observed or reported condition is found, correct the cause (if
possible) before proceeding to the next step.
7. If the fault is not visually evident, determine the symptom and GO to Symptom Chart .
Symptom Chart z
Front wheel bearing(s)
z Loose or damaged front or rear suspension components
z Loose, damaged or missing suspension fastener(s)
z Damaged spring(s)
z Damaged or leaking strut and spring assemblies
z Damaged or leaking shock absorber(s)
z Worn or damaged suspension bushing(s)
z Loose, worn or damaged steering system components
z Damaged axle components
Symptom Chart Condition
Possible Sources Action
z Dogtracking zExcessive rear
thrust angle. z
CHECK the wheel alignment.
ADJUST as necessary.
z Front or rear
suspension
components. z
INSPECT the front and rear
suspension system. REPAIR
or INSTALL new suspension
components as necessary.
REFER to Section 204 - 01 or
Section 204 - 02 .
z Drive axle
damaged. z
REPAIR as necessary. Refer
to the appropriate section in
Group 205 for the procedure..
z Drift/pull zUnequal tire
pressure. z
ADJUST tire pressure.
z Excessive side-to-
side difference in
caster or camber. z
CHECK the wheel alignment.
ADJUST as necessary.
z Tire forces. zROTATE tires front to rear.
z Unevenly loaded or
overloaded vehicle. z
NOTIFY the customer of
incorrect vehicle loading.
z Steering
components. z
REFER to Section 211 - 00 .
z Brake drag. zREFER to Section 206 - 00 .
z Front bottoming
or riding low z
Strut(s). zINSTALL new strut(s) as
necessary. REFER to Section 204 - 01 .
z Front coil springs
(5310). z
CHECK ride height. INSTALL
new springs as necessary.
REFER to Section 204 - 01 .
z Incorrect tire
wear z
Incorrect tire
pressure (rapid
center rib or inner
and outer edge
wear). z
ADJUST tire pressure. Klj . 2 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Excessive front or
rear toe (rapid inner
or outer edge
wear). z
CHECK the wheel alignment.
ADJUST as necessary.
z Excessive negative
or positive camber
(rapid inner or outer
edge wear). z
CHECK the wheel alignment.
ADJUST as necessary.
z Tires out of balance
(tires cupped or
dished). z
BALANCE tires.
z Rough ride zStrut(s). zINSTALL new strut(s) as
necessary. REFER to Section 204 - 01 .
z Shock absorber(s). zINSTALL new shock absorber
(s) as necessary.
z Front coil springs or
rear springs (5560). z
INSTALL new front coil
springs or rear springs as
necessary. REFER to Section 204 - 01 or
Section 204 - 02 .
z Shimmy or
wheel tramp z
Loose wheel nut(s). zTIGHTEN to specification.
REFER to Section 204 - 04 .
z Loose front
suspension
fasteners. z
TIGHTEN to specification.
REFER to Section 204 - 01 .
z Front wheel bearing
(s). z
REFER to Wheel Bearing Inspection in this section.
z Wheel or tire
runout. z
REFER to Section 204 - 04 .
z Tire flatspotting. zREFER to Section 204 - 04 .
z Shock absorber(s). zINSTALL new shock absorber
(s) as necessary.
z Loose, worn or
damaged ball joint
(s). z
GO to the Ball Joint Inspection
component test in this section.
z Loose, worn or
damaged steering
components. z
REFER to Section 211 - 00 .
z Front wheel
alignment. z
CHECK the wheel alignment.
ADJUST as necessary.
z Sticky steering,
poor returnability z
Ball joints. zGO to the Ball Joint Inspection
component test in this section.
z Steering
components. z
REFER to Section 211 - 00 .
z Steering wheel
off- center z
Unequal front or
rear toe settings
(side-to- side). z
CHECK the wheel alignment.
ADJUST as necessary.
z Steering
components. z
REFER to Section 211 - 00 .
z Sway or roll zOverloaded,
unevenly or
incorrectly loaded
vehicle. z
NOTIFY the customer of
incorrect vehicle loading.
z Loose wheel nut(s). zTIGHTEN to specification. Klj . 3 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

SPECIFICATIONS
SECTION 204-
04: Wheels and Tires 2003 Mustang Workshop Manual General Specifications
Item Specification
Lubricants
Silicone Dielectric Compound D7AZ-
19A331-
A ESE-
M1C171- A Cleaners
Liquid Soap ESR-
M99B135- A Professional Choke and Linkage Cleaner
E8AZ-
19A501- AA ESR-
M14P10- A Custom Bright Metal Cleaner
8A-19522-
A ESR-
M5B194- B Aluminum Wheel Repair Compound E7AZ-
19554-
A ESA-
M4G280- A Tire Balance Weight
Max tire balance weight 140g (5 oz) per wheel
70g (2.5 oz) per flange Tire inflation
Tires See safety certification sticker located inside glove
compartment door
Torque Specifications Description Nm lb-
ft Wheel nuts 129 95 Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Safety Precautions
WARNING: Never run the engine with one wheel off the ground, for example, when
changing a tire. The wheel(s) resting on the ground could cause the vehicle to move.
WARNING: The tire and wheel must always be correctly matched. It is very important to
determine the size of each component before any assembly operations commence. Failure to
adhere to these instructions can result in an explosive separation and cause serious bodily
injury or death.
WARNING: Aftermarket aerosol tire sealants are extremely flammable. Always question
the customer to make sure these products have not been used.
WARNING: Aftermarket wheel assemblies may not be compatible with the vehicle. Use of
incompatible wheel assemblies can result in equipment failure and possible injury. Use only
approved wheel assemblies.
WARNING: Use only wheels and wheel nuts that have been designed for current model
year Ford trucks. Aftermarket wheels or wheel nuts may not fit or function correctly, and can
cause personal injury or damage the vehicle.
WARNING: Always wear safety goggles or a face shield when performing any work with
tire and wheel assemblies.
CAUTION: Do not clean aluminum wheels with steel wool, abrasive- type cleaners or
strong detergents. Use Custom Bright Metal Cleaner 8A-19522- A or equivalent meeting Ford
specifications ESR- M5B194-B.
CAUTION: Reduce the air pressure as much as possible by pushing the valve core
plunger in prior to removing the valve core. Avoid working in a position in which the face or
body is directly over a tire in which there is pressure.
When performing any inspection or repair procedures on wheels (1007/1015) and tires, follow the
preceding safety precautions. SECTION 204-
04: Wheels and Tires 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Wheels And Tires
WARNING: Do not mix different types of tires, such as radial, bias, or bias- belted, on the
same vehicle except in emergencies. Vehicle handling can be seriously affected and can result
in loss of control.
Factory-installed tires and wheels are designed to operate satisfactorily with loads up to and including
full- rated load capacity when inflated to recommended inflation pressures.
Tire and Wheel Runout
Excessive radial and lateral runout of a wheel and tire assembly can cause roughness, vibration,
wheel tramp, tire wear, and steering wheel tremor.
Before checking runout, and to avoid false readings caused by temporary flat spots in the tires, check
runout only after the vehicle has been driven far enough to warm the tires. For additional information,
refer to Section 100 - 04 .
SECTION 204-
04: Wheels and Tires 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...