test G FORD MUSTANG 2003 Service Manual

PINPOINT TEST B: ENGINE TICKING NOISE No
INSPECT the wheel
bearings. ADJUST or
REPAIR as necessary.
TEST the system for
normal operation.
A6 CHECK THE FRONT SUSPENSION
z
Check the front suspension for:
zBroken or loose bolts.
z Damaged springs.
z Worn or damaged upper and lower control arm
bushings.
z Loose or rough front bearings.
z Uneven tire wear.
z Are all the suspension components in satisfactory
condition? Yes
GO to
A7 .
No
REPAIR or INSTALL
new components as
necessary. TEST the
system for normal
operation. A7 RESURFACE THE FRONT BRAKE DISCS
z
CAUTION: Do not use a bench lathe to machine brake
discs.
z NOTE: Follow the manufacturer's instructions to machine the
brake discs. After machining, make sure the brake disc meets
the thickness specification.
z Refer to Brake Disc Machining in this section. Resurface the
front brake discs. Road test the vehicle.
z Is the vibration/shudder present? Yes
GO to
A8 .
No
Vehicle is OK. A8 CHECK THE REAR SUSPENSION
z
Check the rear suspension for:
zBroken or loose bolts.
z Damaged or worn springs or spring bushings.
z Worn or damaged upper and lower control arm
bushings.
z Worn or damaged trailing arms.
z Loose or rough rear bearings.
z Uneven tire wear.
z Are all the suspension components in satisfactory
condition? Yes
GO to
A9 .
No
REPAIR or INSTALL
new components as
necessary. TEST the
system for normal
operation. A9 RESURFACE THE REAR BRAKE DISC OR DRUM
z
CAUTION: Do not use a bench lathe to machine brake
discs.
z NOTE: Follow the manufacturers instructions to machine the
brake discs. After machining, make sure the brake disc meets
the thickness specification.
z Refer to Brake Disc Machining in this section. Resurface the
rear brake discs or drums. Road test the vehicle.
z Is the vibration/shudder present? Yes
CHECK the front
suspension for wear or
damage. RESURFACE
the front brake discs.
TEST the system for
normal operation.
No
Vehicle is OK.
Test Step Result / Action to Take
B1 CHECK FOR TICKING NOISE AT THE FUEL
RAIL z
Disconnect the first fuel line clip. Yes Klj . 49 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Is the ticking noise gone? CHECK for TSB for applicable vehicle.
REPAIR as necessary. TEST the system
for normal operation.
No
GO to
B2 .
B2 CHECK FOR TICKING NOISE AT THE FUEL
INJECTOR z
Using an EngineEAR, listen at the fuel
injectors by placing a probe on each injector.
To isolate the faulty injector, disconnect the
injector electrical connector and listen for the
noise.
z Is the fuel injector the source of the ticking
noise? Yes
INSTALL a new fuel injector. REFER to
Section 303
- 04A for 3.8L engines or
Section 303 - 04B for 4.6L (2V) engines.
TEST the system for normal operation.
No
GO to B3 .
B3 CHECK THE BELT TENSIONER FOR TICKING
NOISE z
Inspect the accessory drive. Check for the belt
tensioner bottoming at end of travel or not at
end of stroke.
z Using an EngineEAR, listen at the belt
tensioner.
z Is the belt tensioner the source of the
noise? Yes
INSTALL a new belt tensioner. TEST the
system for normal operation.
No
GO to
B4 .
B4 CHECK THE WATER PUMP FOR TICKING
NOISE z
Using an EngineEAR, listen at the water pump
for ticking noise.
z Is the water pump the source of the noise? Yes
INSTALL a new water pump. REFER to
Section 303
- 03A . TEST the system for
normal operation.
No
GO to B5 .
B5 CHECK FOR AN OBSTRUCTION OF THE
COOLING FAN z
Inspect the cooling fan for obstructions.
z Check the cooling fan and shroud for wear or
damage.
z Was there an obstruction or does the
cooling fan show signs of damage? Yes
REPAIR or INSTALL a new cooling fan.
REFER to
Section 303 - 03A . TEST the
system for normal operation.
No
GO to B6 .
B6 CHECK THE OIL PUMP FOR TICKING NOISE
z
Check the oil pump using EngineEARs and
probe at the oil filter adapter to verify the oil
pump as a source.
z Is the oil pump the source of the noise? Yes
INSTALL a new oil pump. REFER to
Section 303
- 01A for 3.8L engines or
Section 303 - 01B for 4.6L (2V) engines.
TEST the system for normal operation.
No
GO to B7 .
B7 CHECK VALVE LIFTERS OR LASH
ADJUSTERS FOR CORRECT OPERATION z
Check valve lifter/lash adjuster for correct
operation, using EngineEARs.
z Are the valve lifters/lash adjusters Yes
VERIFY customer concern. CONDUCT a
diagnosis of other suspect components. Klj . 50 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST C: ACCESSORY DRIVE BEARING HOOT
PINPOINT TEST D: POWER STEERING MOAN
PINPOINT TEST E: ENGINE DRIVEN COOLING FAN MOAN operating correctly?
No
INSTALL a new valve lifter/lash adjuster
(s). TEST the system for normal
operation.
Test Step Result / Action to Take
C1 CHECK THE IDLER AND TENSIONER
PULLEY BEARINGS z
Carry out the Vehicle Cold Soak
Procedure in this section.
z Key in START position.
z Place an EngineEAR probe directly on the
pulley center post or bolt to verify which
bearing is making the noise.
z Key in OFF position.
z Is either bearing making the noise? Yes
INSTALL a new pulley/idler. CARRY OUT the
Vehicle Cold Soak Procedure and TEST the
system for normal operation.
No
CONDUCT a diagnosis on other suspect
accessory drive components.
Test Step Result / Action to Take
D1 CHECK THE POWER STEERING
SYSTEM z
Carry out the Vehicle Cold Soak
Procedure in this section.
z Key in START position.
z Turn the steering wheel while the noise
is occurring and listen for changes in
sound pitch or loudness.
z Key in OFF position.
z Does the sound pitch or loudness
change while turning the steering
wheel? Yes
GO to
D2 .
No
CONDUCT a diagnosis on other suspect
accessory drive components. D2 VERIFY THE SOURCE
z
Key in START position.
z Place an EngineEAR probe near the
power steering pump/reservoir while the
noise is occurring. While an assistant
turns the steering wheel, listen for
changes in sound pitch or loudness.
z Key in OFF position.
z Does the sound pitch or loudness
change while turning the steering
wheel? Yes
VERIFY that the supply tube to the pump is
unobstructed. CHECK the fluid condition and
level. DRAIN the fluid and REFILL. CARRY
OUT the Vehicle Cold Soak Procedure and
TEST the system for normal operation. REFER
to Section 211
- 02 .
No
Normal system operation. Test Step Result / Action to Take
E1 CHECK THE ENGINE DRIVEN COOLING
FAN AFTER A COLD SOAK Klj . 51 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST F: DRUMMING NOISE z
Carry out the Vehicle Cold Soak Procedure
in this section.
z Key in START position.
z Assess the airflow.
z Raise the engine speed to 1500 rpm while
listening for the moan to increase in
proportion to the airflow.
z Key in OFF position.
z Does the moan increase in proportion to
the airflow? Yes
TEST the fan for normal operation. If the
fan tests normal, GO to
E2 . Otherwise,
REPAIR as necessary.
No
Normal system operation. E2 CHECK THE ENGINE DRIVEN COOLING
FAN AT NORMAL OPERATING TEMPERATURE z
Key in START position.
z Run the engine to normal operating
temperature while listening for the moan to
stop.
z Key in OFF position.
z Does the moan stop? Yes
Normal clutch operation.
No
INSTALL a new fan clutch. TEST the
system for normal operation.
Test Step Result / Action to Take
F1 CHECK THE EXHAUST SYSTEM
z
Key in START position.
z Increase the engine rpm until the noise is the loudest. Note
the engine rpm.
z Key in OFF position.
z Add approximately 9 kg (20 lb) of weight to the exhaust
system. First place the weight at the tail pipe and test, then
at the front pipe.
z Key in START position.
z Increase the engine rpm and listen for the drumming noise.
Note the engine rpm if the noise occurs.
z Key in OFF position.
z Using a vibration analyzer (VA), determine the amount of
vibration that occurs with the drumming noise.
z Is the noise/vibration reduced or eliminated, or does the
noise/vibration occur at a different rpm? Yes
CARRY OUT
Exhaust System Neutralizing in this
section. TEST the system
for normal operation.
No
GO to F2 .
F2 POWERTRAIN/DRIVETRAIN MOUNT NEUTRALIZING
z
Carry out Powertrain/Drivetrain Mount Neutralizing in this
section. Test the system for normal operation.
z Is the noise reduced or eliminated? Yes
Vehicle OK. TEST the
system for normal
operation.
No Klj . 52 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST G: ENGINE TICKING, KNOCKING OR CONTINUOUS
RATTLE
PINPOINT TEST H: FRONT SUSPENSION NOISE CONDUCT diagnosis of
other suspect components.
Test Step Result / Action to Take
G1 CHECK FOR NOISE AT THE VALVE COVERS
AND THE FRONT COVERS (OHC ENGINES) z
Carry out the Vehicle Cold Soak Procedure in
this section.
z Key in START position.
z NOTE: For a short- duration ticking noise,
multiple engine starts may be necessary.
z Using an EngineEAR, listen closely at the valve
covers and the front covers (OHC engines) by
placing the probe near the surface of the valve
cover and then on the surface front cover.
z Key in OFF position.
z Is the noise source apparent? Yes
REMOVE the appropriate cover and
INSPECT for loose, worn/broken
components. REPAIR as necessary.
TEST the system for normal operation.
No
GO to
G2 .
G2 CHECK FOR NOISE AT THE CYLINDER
BLOCK z
Key in START position.
z Using an EngineEAR, listen closely at the
cylinder block by placing a probe on or near
each freeze plug.
z Key in OFF position.
z Is the noise source apparent? Yes
REPAIR or INSTALL new components
as necessary.
No
GO to
G3 .
G3 CHECK FOR NOISE WHILE DISCONNECTING
EACH FUEL INJECTOR ELECTRICAL
CONNECTOR, ONE AT A TIME z
Key in START position.
z Disconnect each fuel injector electrical
connector, one at a time, to decrease piston
force and listen for the noise.
z Key in OFF position.
z Is the noise reduced or eliminated? Yes
INSTALL a new fuel injector. TEST the
system for normal operation.
No
INSPECT accessory drive system or the
transmission as a possible source.
Test Step Result / Action to Take
H1 ROAD TEST THE VEHICLE
z
Test drive the vehicle.
z NOTE: An assistant will be needed for this road test.
z During the road test, drive the vehicle over a rough road.
Using ChassisEARs, determine from which
area/component the noise is originating.
z Is there a squeak, creak or rattle noise? Yes
GO to
H2 .
No
The suspension system is
OK. CONDUCT a diagnosis
on other suspect systems. H2 INSPECT THE STEERING SYSTEM
Yes Klj . 53 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST I: REAR SUSPENSION NOISE z
WARNING: The electrical power to the air
suspension system must be shut off prior to hoisting,
jacking or towing an air suspension vehicle. This can
be accomplished by turning off the air suspension
switch. Failure to do so can result in unexpected
inflation or deflation of the air springs, which can result
in shifting of the vehicle during these operations.
z Raise and support the vehicle.
z Check the steering system for wear or damage. Carry out a
steering linkage test. Refer Section 211 - 00 .
z Inspect the tire wear pattern. Refer to Tire Wear Patterns
chart in this section.
z Are the steering components worn or damaged? REPAIR the steering
system. INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H3 .
H3 FRONT SHOCK ABSORBER/STRUT CHECK
z
Check the front shock absorbers/strut mounts for loose
bolts or nuts.
z Check the front shock absorbers/struts for wear or damage.
Carry out a "bounce test".
z Are the front shock absorbers/struts loose or
damaged? Yes
TIGHTEN to specifications if
loose. INSTALL new front
shock absorbers/struts if
damaged. TEST the system
for normal operation.
No
GO to
H4 .
H4 CHECK THE FRONT SPRINGS
z
Check the front spring and front spring mounts/brackets for
wear or damage.
z Are the front springs or spring mounts/brackets worn
or damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H5 .
H5 CHECK THE CONTROL ARMS/RADIUS ARMS
z
Inspect the control arm bushings for wear or damage.
z Inspect for twisted or bent control/radius arm.
z Are the control/radius arms damaged or worn? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H6 .
H6 CHECK THE STABILIZER BAR/TRACK BAR
z
Check the stabilizer bar/track bar bushings and links for
damage or wear.
z Check the stabilizer bar/track bar for damage.
z Check for loose or damaged stabilizer bar isolators or
brackets.
z Are the stabilizer bar/track bar components loose, worn
or damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
Suspension system OK.
CONDUCT diagnosis on
other suspect systems.
Test Step Result / Action to Take Klj . 54 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST J: WHEEL AND TIRE I1 ROAD TEST THE VEHICLE
z
Test drive the vehicle.
z NOTE: An assistant will be needed for this road test.
z During the road test, drive the vehicle over a rough road.
Using ChassisEARs, determine from which
area/component the noise is originating.
z Is there a squeak, creak or rattle noise? Yes
GO to
I2 .
No
The suspension system is
OK. Conduct a diagnosis on
other suspect systems. I2 REAR SHOCK ABSORBER/STRUT CHECK
z
WARNING: The electrical power to the air
suspension system must be shut off prior to hoisting,
jacking or towing an air suspension vehicle. This can
be accomplished by turning off the air suspension
switch. Failure to do so can result in unexpected
inflation or deflation of the air springs, which can result
in shifting of the vehicle during these operations.
z Raise and support the vehicle.
z Check the rear shock absorber/strut mounts for loose bolts
or nuts.
z Check the rear shock absorbers/struts for damage. Carry
out a shock absorber check.
z Are the rear shock absorbers/struts loose or damaged? Yes
TIGHTEN to specifications if
loose. INSTALL new rear
shock absorbers/struts if
damaged. TEST the system
for normal operation.
No
GO to
I3 .
I3 CHECK THE REAR SPRINGS
z
Check the rear springs and rear spring mounts/brackets for
wear or damage.
z Are the rear springs or spring mounts/brackets worn or
damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
I4 .
I4 CHECK THE CONTROL ARMS/TRAILING ARMS
z
Inspect the control arm/trailing arm bushings for wear or
damage. Check for loose control arm/trailing arm bolts.
z Inspect for twisted or bent control arm/trailing arms.
z Are the control arm/trailing arms loose, damaged or
worn? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
I5 .
I5 CHECK THE STABILIZER BAR/TRACK BAR
z
Check the stabilizer bar/track bar bushings and links for
damage or wear.
z Check the stabilizer bar/track bar for damage.
z Check for loose or damaged stabilizer bar isolators or
brackets.
z Are the stabilizer bar/track bar components loose, worn
or damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
Suspension system OK.
CONDUCT diagnosis on
other suspect systems.
Test Step
Result / Action to Klj . 55 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Take
J1 ROAD TEST THE VEHICLE
z
NOTE: Wheel or tire vibrations felt in the steering wheel are most
likely related to the front wheel or tire. Vibration felt through the
seat are most likely related to the rear wheel or tire. This may not
always be true, but it can help to isolate the problem to the front
or rear of the vehicle.
z Test drive the vehicle at different speed ranges.
z During the road test, if the vibration can be eliminated by placing
the vehicle in neutral or is affected by the speed of the engine,
the cause is not the wheels or tires.
z Is there a vibration and noise? Yes
GO to
J2 .
No
The wheel and tires
are OK. CONDUCT a
diagnosis on other
suspect systems. J2 CHECK THE FRONT WHEEL BEARINGS
z
Check the front wheel bearings. Refer to Wheel Bearing Check in
this section.
z Are the wheel bearings OK? Yes
GO to
J3 .
No
INSPECT the wheel
bearings. ADJUST or
REPAIR as necessary.
TEST the system for
normal operation. J3 INSPECT THE TIRES
z
Check the tires for missing weights.
z Check the wheels for damage.
z Inspect the tire wear pattern. Refer to the Tire Wear Patterns
chart in this section.
z Do the tires have an abnormal wear pattern? Yes
CORRECT the
condition that caused
the abnormal wear.
INSTALL new tire(s).
TEST the system for
normal operation.
No
GO to
J4 .
J4 TIRE ROTATION
z
Spin the tires slowly and watch for signs of lateral runout.
z Spin the tires slowly and watch for signs of radial runout. Yes
GO to
J5 .
No
CHECK the wheel and
tire balance.
CORRECT as
necessary. TEST the
system for normal
operation. Klj . 56 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Are there signs of visual runout? J5 RADIAL RUNOUT CHECK ON THE TIRE
z
Measure the radial runout of the wheel and tire assembly. A
typical specification for total radial runout is 0.045 inch.
z Is the radial runout within specifications? Yes
GO to
J8 .
No
GO to J6 .
J6 RADIAL RUNOUT CHECK ON THE WHEEL
z
Measure the radial runout of the wheel. A typical specification for
total radial runout is 0.045 inch.
z Is the radial runout within specifications? Yes
INSTALL a new tire.
TEST the system for
normal operation.
No
GO to
J7 .
J7 CHECK THE HUB/BRAKE DISC OR DRUM PILOT RUNOUT OR
BOLT CIRCLE RUNOUT z
Measure the pilot or bolt circle runout. A typical specification for
radial runout is:
zPilot runout— less than 0.15 mm (0.006 inch).
z Bolt circle runout— less than 0.38 mm (0.015 inch).
z Is the radial runout within specifications? Yes
INSTALL a new wheel.
TEST the system for
normal operation.
No
REPAIR or INSTALL
new components as
necessary. REFER to
Section 204
- 01 for the
front wheels or Section 204 - 02 for the rear
wheels. J8 LATERAL RUNOUT CHECK ON THE TIRE
z
Measure the lateral runout of the wheel and tire assembly. A
typical specification for total lateral runout is 1.14 mm (0.045
inch). Yes
Wheel and tires OK.
CONDUCT diagnosis
on other suspect
systems. Klj . 57 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST K: HIGH SPEED SHAKE OR SHIMMY z
Is the lateral runout within specifications? No
GO to
J9 .
J9 LATERAL RUNOUT CHECK ON THE WHEEL
z
Measure the lateral runout of the wheel. A typical specification for
total radial runout is 1.14mm (0.045 inch.
z Is the lateral runout within specifications? Yes
INSTALL a new tire.
TEST the system for
normal operation.
No
GO to
J10 .
J10 CHECK THE FLANGE FACE LATERAL RUNOUT
z
Measure the flange face lateral runout. A typical specification for
lateral runout is:
zHub/brake disc— less than 0.13 mm (0.005 inch).
z Axle shaft— less than 0.25 mm (0.010 inch).
z Is the lateral runout within specifications? Yes
INSTALL a new wheel.
TEST the system for
normal operation.
No
REPAIR or INSTALL
new components as
necessary. REFER to
Section 204
- 01 for the
front wheels or Section 204 - 02 for the rear
wheels. Test Step Result / Action to Take
K1 CHECK FOR FRONT WHEEL BEARING ROUGHNESS
z
Chock the rear wheels.
z Raise and support the front end of the vehicle so that the front
wheel and tire assemblies can spin.
z Spin the front tires by hand. Refer to Wheel Bearing Check in
this section.
z Do the wheel bearings feel rough? Yes
INSPECT the wheel
bearings. REPAIR as
necessary. TEST the
system for normal
operation.
No
GO to
K2 .
K2 CHECK THE END PLAY OF THE FRONT WHEEL BEARINGS
z
Check the end play of the front wheel bearings. Refer to
Section 204 - 01 .
z Is the end play OK? Yes
GO to
K3 .
No
ADJUST or REPAIR as
necessary. TEST the
system for normal Klj . 58 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...