brake FORD MUSTANG 2003 Repair Manual

z
wheel bearing life.
z brake cooling.
New wheels need to be installed when vehicle's wheels:
zare bent.
z are cracked.
z are dented.
z are heavily corroded.
z are leaking.
z have elongated wheel hub bolt holes.
z have excessive lateral or radial runout.
Wheel and tire assemblies are attached by six wheel nuts.
It is mandatory to use only the tire sizes recommended on the tire chart attached to the vehicle. Larger
or smaller tires can damage the vehicle, affect durability, and require changing the speedometer
calibration. Make sure wheel size and offsets match those recommended for the tire in use. 1. Inspect for signs of uneven wear that may indicate a need for balancing, rotation, front suspension alignment, damaged tie- rod, or steering components.
2. Check tires for: zcuts.
z stone bruises.
z abrasions
z blisters.
z embedded objects.
3. Tread wear indicators are molded into the bottom of the tread grooves. Install a new tire when the indicator bands become visible.
Symptom Chart Symptom Chart Condition
Possible Sources Action
z Tires show
excess wear on
edge of tread z
Underinflated tires. zADJUST air pressure
in tires.
z Vehicle overloaded. zRETURN vehicle.
NOTIFY customer of
overload condition.
z High- speed cornering. zRETURN vehicle.
NOTIFY customer of
cause of condition.
z Incorrect ride height. zSET ride height.
z Incorrect wheel alignment. zSET alignment to
specification. REFER Klj . 2 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

to
Section 204 - 00 .
z Incorrect tire rotation
intervals. z
ADVISE customer of
condition. ROTATE
tires.
z Tires show
excess wear in
center of tread z
Tires overinflated. zADJUST air pressure.
z Other excessive
tire wear
problems z
Incorrect tire rotation
intervals. z
ADVISE customer of
condition. ROTATE
tires.
z Incorrect tire pressure. zADJUST pressure.
z Loose or leaking shock
absorbers. z
TIGHTEN or INSTALL
new shock absorbers
as necessary.
z Incorrect wheel alignment. zSET alignment to
specification. REFER
to Section 204 - 00 .
z Loose, worn or damaged
suspension components. z
REFER to Section 204 - 00 .
z Wheel and tire assembly
out of balance. z
BALANCE wheel and
tire assembly.
z Excessive lateral or radial
runout of wheel. z
REFER to Section 100 - 04 .
z Wobble or
shimmy z
Damaged wheel bearings. zREFER to Section 204 - 00 .
z Loose or damaged
suspension components. z
REFER to Section 204 - 00 .
z Bent wheel. zINSTALL a new wheel
as necessary.
z Damaged tire. zINSTALL a new tire as
necessary.
z Loose wheel nuts. zTIGHTEN to
specification.
z High- speed
shake z
Wheel hub face/pilot/bolt
circle runout.
z Tires/wheels.
z Wheel bearings.
z Suspension/steering
linkage.
z Engine.
z Transmission.
z Brake discs/imbalance. z
REFER to Section 100 - 04 .
z Vehicle vibration zDriveline — engine.
z Tires. z
REFER to Section 100 - 04 . Klj . 3 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Wheel Leaks
WARNING: Wheel repairs that use welding or peening are not approved. An inner tube is
not an acceptable repair for leaking wheels or tires.
If the air pressure in a tire mounted on an aluminum wheel is found to be low, perform the
following procedure before considering installation of a new wheel.
1. Remove the tire and wheel assembly, and inspect the wheel for structural damage. If none exists, go to Step 2. If the wheel is damaged, install a new wheel.
2. With the tire mounted on the wheel, locate the air leak using a water bath or equivalent method, and mark the location. Check the complete wheel for possible additional leaks. When leaks are
marked, dismount the tire marking valve location on the tire for correct indexing.
3. On the tire side of the wheel, thoroughly clean the leaking area with an appropriate choke cleaner or use sandpaper of approximately 80- grit to remove all contamination. Using the
sandpaper, score the surface of the leaking area to improve adhesion of the sealer. If the valve
stem is close to the area, remove it.
4. Use a clean cloth to remove all cleaner or sanding dust.
5. NOTE: Do not use a torch containing oxyacetylene.
Heat the prepared area with a Heat Gun or a propane torch until aluminum wheel repair
compound flows. Apply the hot melt material over the prepared area using a liberal flow and
wiping action. Repair is most effective when heat is applied to the brake side of the rim, and the
sealer is melted by heat in the metal.
6. Apply only enough heat to melt the sealer, then remove the heat source. After repairing the leak, allow the wheel to cool until it can be handled safety.
7. CAUTION: Use caution when mounting the tire so as not to damage the sealer.
Index and assemble the tire and wheel. Inflate the tire to the recommended pressure as
indicated on the tire pressure decal.
8. Repeat Step 2 to verify repair.
9. When the repair is completed, balance the assembly and install it on the vehicle.
SECTION 204-
04: Wheels and Tires 2003 Mustang Workshop Manual Material
Item Specification
Professional Choke and
Linkage Cleaner
F8AZ-
19520- AB WSS-
M14P10-
B Aluminum Wheel Repair
Compound ESA-
M4G280-
A Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Installation
1. WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign
material present on the mounting surfaces of the wheel and the surface of the wheel hub,
brake drum or brake disc that contacts the wheel. Installing wheels without correct
metal- to-metal contact at the wheel mounting surfaces can cause the wheel nuts to
loosen and the wheel to come off while the vehicle is in motion, causing loss of control.
Position the wheel and tire on the vehicle.
2. CAUTION: Failure to tighten the wheel nuts in a star pattern can result in high brake
disc runout, which will speed up the development of brake roughness, shudder and
vibration.
Install the wheel nuts hand- tight, then lower the vehicle. Tighten the wheel nuts to specification
in a star- pattern sequence.
3. Install the center cap, if so equipped. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

When these conditions exist, check the driveline angles as described in the General Procedures
portion of this section.
If the tires and driveline angle are not the cause, carry out the NVH tests to determine whether the
concern is caused by a condition in the axle. Refer to
Section 100 - 04 .
Universal Joint (U- Joint) Wear
Place the vehicle on a frame hoist and rotate the driveshaft by hand. Check for rough operation or
seized U- joints. Install a new U- joint if it shows signs of seizure, excessive wear, or incorrect seating.
Refer to Section 205 - 01 .
Wheel Hub or Axle Flange Bolt Circle Runout
NOTE: The brake discs must be removed to carry out all runout measurements.
1. Position the special tool perpendicular to the wheel hub or axle flange bolt, as close to the hub or flange face as possible. Zero the indicator to allow the pointer to deflect either way.
2. Rotate the hub or flange until the next bolt is contacted. Record the measurement and continue until each bolt is checked. The difference between the maximum and minimum contact readings
will be the total wheel hub or axle flange bolt pattern runout. The runout must not exceed 0.38
mm (0.015 inch).
Pilot Runout
1. Position the special tools as close to the hub or axle flange face as possible. Zero the indicator to allow the pointer to deflect either way.
2. Rotate the hub or flange one full turn and note the maximum and minimum readings. The difference between the maximum and minimum readings will be the total pilot runout. Pilot
runout must not exceed 0.15 mm (0.006 inch).
Wheel Hub or Axle Flange Face Runout Klj . 5 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Component Tests
Driveline Vibration
An analysis of driveline vibration can also be conducted using the Vibration Analyzer; follow the
manufacturer's directions.
Driveline vibration exhibits a higher frequency and lower amplitude than does high-
speed shake.
Driveline vibration is directly related to the speed of the vehicle and is usually noticed at various speed
ranges. Driveline vibration can be perceived as a tremor in the floorpan or is heard as a rumble, hum,
or boom. Driveline vibration can exist in all drive modes, but may exhibit different symptoms depending
upon whether the vehicle is accelerating, decelerating, floating, or coasting. Check the driveline angles
if the vibration is particularly noticeable during acceleration or deceleration, especially at lower speeds.
Driveline vibration can be duplicated by supporting the axle upon a hoist or upon jack stands, though
the brakes may need to be applied lightly in order to simulate road resistance.
1. Raise the vehicle promptly after road testing. Use a twin- post hoist or jack stands to prevent tire
flat- spotting. Engage the drivetrain and accelerate to the observed road test speed to verify the lubricant type.
205 - 02B . CLEAN and
REFILL the axle to
specification.
z Axle overheating zLubricant level too
low. z
CHECK the lubricant level.
FILL the axle to specification.
z Incorrect or
contaminated
lubricant type. z
INSPECT the axle for
damage. REPAIR as
necessary. CLEAN and
REFILL the axle to
specification.
z Bearing preload
adjusted too tight. z
CHECK the ring and pinion for
damage. INSPECT the ring
and pinion wear pattern.
ADJUST the preload as
necessary.
z Excessive gear
wear. z
INSPECT all the axle gears
for wear or damage. INSTALL
new components as
necessary.
z Incorrect ring gear
backlash. z
INSPECT the ring gear for
scoring. INSPECT the ring
and pinion wear pattern.
ADJUST the ring gear
backlash as necessary.
z Broken gear teeth
on the ring gear
or pinion z
Overloading the
vehicle. z
INSTALL a new ring and
pinion. REFER to Section 205 - 02A or
Section 205 - 02B .
z Axle shaft broken zOverloading the
vehicle. z
INSTALL a new axle shaft.
REFER to Section 205 - 02A or
Section 205 - 02B .
z Misaligned axle
shaft tube. z
INSPECT the axle for
damage. CHECK axle shaft
tube alignment. INSTALL a
new axle shaft. REFER to
Section 205 - 02A or
Section 205 - 02B . Klj . 11 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

off the floor.
With the engine off, raise only one rear wheel. Install the special tool on the wheel nuts.
Use a torque wrench with a capacity of at least 271 Nm (200 lb-
ft) to rotate the axle shaft. Be sure that
the transmission is in NEUTRAL, and that one rear wheel is on the floor while the other rear wheel is
raised off the floor. The breakaway torque required to start rotation must be at least 27 Nm (20 lb- ft).
The initial breakaway torque may be higher than the continuous turning torque.
The axle shaft must turn with even pressure throughout the check without slipping or binding. If the
torque reading is less than specified, check the differential case. Refer to Section 205 - 02A or
Section 205 - 02B .
Traction- Lok® Differential Check Road Test
1. Place one wheel on a dry surface and the other wheel on ice, mud or snow.
2. Gradually open the throttle to obtain maximum traction prior to break away. The ability to move the vehicle demonstrates correct operation of a Traction- Lok® rear axle assembly.
3. When starting with one wheel on an excessively slippery surface, a slight application of the parking brake may be necessary to help energize the Traction- Lok® feature of the differential.
Release the brake when traction is established. Use light throttle on starting to provide
maximum traction.
4. If, with unequal traction, both wheels slip, the limited slip rear axle has done all it can possibly do.
5. In extreme cases of differences in traction, the wheel with the least traction may spin after the Traction-Lok® has transferred as much torque as possible to the non- slipping wheel. Klj . 15 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4 4222 Differential bearing cup
5 4067 Differential bearing shim
6 4216 Rear axle differential gear case bolt
7 4204 Differential case
8 — Ring gear (part of 4209)
9 — Bearing cap (part of 4010)
10 4010 Rear axle housing
11 373098-
S Filler plug
12 4662 Collapsible spacer
13 4670 Rear axle drive pinion shaft oil slinger
14 4676 Rear axle drive pinion seal
15 4851 Pinion flange
16 389546-S100 Pinion nut
17 4621 Differential pinion bearing
18 2C026 Rear brake disc
19 — Axle shaft flange (part of 4234)
20 2C189 Rear brake anti-
lock sensor indicator 21 2552 Rear disc brake caliper
22 N601951-S2 Bolt
23 N804361-S100 Clip
24 — Bolt
25 2C190 Rear brake anti-
lock sensor 26 2C101 Left hand rear disc brake adapter
27 2C100 Right hand rear disc brake adapter
28 N8015163-S190 Caliper anchor bolt
29 2C028 Rear wheel brake disc shield
30 N602726-S2 Bolt (3 req'd)
31 4616 Differential drive pinion bearing cup
32 4628 Rear axle pinion bearing cup
33 4630 Differential pinion bearing
34 — Drive pinion gear
(part of 4209)
35 4663 Drive pinion bearing adjustment shim
36 — Bolt (part of 4010)
37 4241 Differential pinion shaft lock bolt
38 4211 Differential pinion shaft
39 4N237 U-
washer 40 383548 Bolt
41 — Rear axle identification tag
42 4033 Differential housing cover
43 4230 Differential pinion thrust washer
44 4215 Differential pinion gear Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Axle Shaft
Removal 1. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
2. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
3. Remove the rear brake disc (2C026). For additional information, refer to Section 206 - 04 .
4. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
5. Remove the differential pinion shaft (4211). 1. Remove the differential pinion shaft lock bolt (4241).
2. Remove the differential pinion shaft.
6. CAUTION: Do not damage the rubber O- ring in the axle shaft groove.
Remove the U- washer (4N237).
1. Push the axle shafts (4234) inboard.
2. Remove the U- washer.
7. CAUTION: Damage to the rear brake anti- lock sensor (2C190) may occur if it is not
removed before the axle shaft.
Carefully remove the rear brake anti- lock sensor. For additional information, refer to Section SECTION 205-
02A: Rear Drive Axle/Differential — Ford 7.5-Inch Ring
Gear 2003 Mustang Workshop
Manual Klj . 1 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

1. Position the two U-
washers on the button end of the axle shaft.
2. Pull the axle shaft outward.
4. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and
Sealer EOAZ- 19554-AA or equivalent meeting Ford specification WSK-M2G351- A5 prior to
installation.
Install the differential pinion shaft. 1. Align the hole in the differential pinion shaft with the case lock bolt hole.
2. Install a new differential pinion shaft lock bolt.
5. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
6. Install the rear brake anti- lock sensor. For additional information, refer to Section 206 - 09A .
7. Install the rear brakes. For additional information, refer to Section 206 - 04 .
8. Install the tire and wheel assembly. For additional information, refer to Section 204 - 04 .
9. Lower the vehicle. Klj . 3 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...