wiring FORD MUSTANG 2003 Repair Manual

14. Disconnect the upper radiator hose from the bypass tube.
15. Disconnect the lower radiator hose from the bypass tube.
16. Disconnect the cooling fan electrical connector.
17. Separate the cooling fan wiring harness from the fan shroud. Klj . 4 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

power steering pump aside.
23. Remove the A/C muffler bracket nut.
24. Remove the bolts and position the A/C compressor aside.
25. Disconnect the crankshaft position (CKP) sensor electrical connector.
26. Remove the wiring harness nuts and position the wiring harness aside. Klj . 6 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

12. Install the clutch release cable shield and the bolt.
All vehicles 13. Loosely install the four oil pan bolts. Tighten the bolts in three stages, and in the sequence shown. 1. Stage 1: Tighten the bolts to 2 Nm (18 lb- in).
2. Stage 2: Tighten the bolts to 20 Nm (15 lb- ft).
3. Stage 3: Tighten the bolts an additional 90 degrees (1/4 turn). 14. Position the wiring harness and install the nuts. Klj . 14 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

19. Install the crankshaft front oil seal. For additional information, refer to
Crankshaft Front Oil Seal in this section.
20. Position the cooling fan and shroud in the installed position.
21. Install the RH cooling fan bolt.
22. Install the LH cooling fan bolt.
23. Attach the cooling fan wiring harness to the fan shroud. Klj . 16 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

28. Connect the degas bottle return hose.
29. Connect the degas bottle vent hose.
30. Connect the wiring harness anchor to the valve cover.
31. Install the positive crankcase ventilation (PCV) valve hose and connect the electrical connector. Klj . 18 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

19.
NOTE: Do not completely remove the bolts.
Loosen the bolts.
20. Lower the front sub- frame.
21. Remove the sub- frame brace.
22. Remove the starter wiring harness nuts and position the wiring harness out of the way. Klj . 4 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Install the oil pan drain plug.
7. Position the starter wiring harness and install the wiring harness nuts.
8. Install the sub-
frame brace. Klj . 7 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

13.
NOTE: Mark the bolts and the crossmember location for assembly reference.
NOTE: RH shown, LH similar.
Remove the four bolts.
14. NOTE: RH shown, LH similar.
Remove the four bolts.
15. Using the jackstands, lower the front subframe.
RH mount 16. Remove the nut and detach the wiring harness.
17. Remove the bolts, the studbolt and the engine mount. Klj . 4 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2. Attach the ground cables and install the nuts.
RH mount 3. Position the engine mount and install the bolts and studbolt.
4. Attach the wiring harness and install the nut. Both mounts Klj . 6 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

14. Remove the bolts and detach the retainer. Position the cables and the bracket aside.
15. Disconnect the evaporative emissions return line.
16. Disconnect the 16-
pin and the 42-pin connectors.
17. Separate the engine control sensor wiring in three locations and position onto the engine.
18. Disconnect the vacuum hoses. Klj . 4 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...