ignition FORD MUSTANG 2003 Manual PDF

17. Remove the throttle body bolts.
18.
NOTE: The gasket is reusable if not damaged.
Remove the throttle body and adapter as an assembly. zInspect and clean the sealing surfaces.
19. Remove the ignition coils.
20. Remove the radio interference capacitors. Klj . 7 ba
242003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

82. Install the generator support brace.
83. Install the accessory drive belt. For additional information, refer to
Section 303 - 05 .
84. Install the radio interference capacitors.
85. Install the ignition coils and bolts. Klj . 30 ba
362003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

94. Install the breather tube.
95. Install the engine control sensor wiring.
Item Part Number Description
1 — To crankshaft position sensor
2 — To A/C compressor
3 — To radio ignition interference capacitor (2)
4 — To fuel injectors (8) Klj . 33 ba
362003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

96. Install the RH and LH special tools.
97. Using the special tool, remove the engine from the stand.
98. Using the special tool, install the crankshaft rear main seal.
zLubricate the oil seal using clean engine oil. 5 — To ignition coils (8)
6 — To engine coolant temperature sensor
7 — To throttle position sensor
8 — To idle air control valve
9 — To EGR vacuum regulator
10 — To differential pressure feedback EGR
11 — To fuel pressure regulator
12 — Fuel injection ground
13 — To generator
14 — To camshaft position sensor
15 — To body
16 — To heated oxygen sensor (2)
17 — Engine bulkhead connector
18 — To low coolant sensor
19 — To body
20 — To power distribution box
21 — To body Klj . 34 ba
362003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

57. Install the accessory drive belt.
58. Install the radio interference capacitors.
59. Install the ignition coils and bolts.
60. Position the throttle body and install the bolts, tightening in the sequence shown. Klj . 20 ba
252003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

69. Install the engine control sensor wiring.
Item Part Number Description
1 — To crankshaft position sensor
2 — To A/C compressor
3 — To radio ignition interference capacitor (2)
4 — To fuel injectors (8)
5 — To ignition coils (8)
6 — To engine coolant temperature sensor
7 — To throttle position sensor
8 — To idle air control valve
9 — To EGR vacuum regulator
10 — To differential pressure feedback EGR
11 — To fuel pressure regulator
12 — Fuel injection ground
13 — To generator
14 — To camshaft position sensor Klj . 23 ba
252003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

a
Refer to the procedure. Oil pan-to-
engine front cover bolts a — — —
Oil pump-
to-cylinder block bolt 10 — 89
Radio ignition interference capacitor bolts 25 18 —
Oil pump screen and pickup tube-
to-main bearing cap stud spacer bolt 25 18 —
Water pump pulley bolts 25 18 —
Throttle body spacer nuts 25 18 —
Vacuum accessory bracket fasteners 10 — 89
Valve cover bolt 10 — 89
Wiring harness support bracket 25 18 —
Water pump-
to-cylinder block bolt 25 18 —
EGR valve to exhaust manifold tube nuts 40 30 —
Power steering pump to engine 25 18 —
Power steering hose bracket nut 25 18 —
Power steering reservoir bracket fasteners 10 — 89
Supercharger degas bottle bolts 10 — 89
Camshaft cap cluster to cylinder head 10 — 89
Timing chain tensioner bolts—
primary 25 18 —
Timing chain tensioner bolts—
secondary 10 — 89
Ignition coil cover bolts 10 — 89
Generator mounting bracket retainers 10 — 89
Oil level indicator tube retainer 10 — 89
Primary timing chain guide-
to-engine bolts 10 — 89
Oil pump screen and pickup tube spacer to main bearing stud 25 18 —
Belt idler pulley bolt 25 18 —
Subframe brace nuts 41 30 — Klj . 5 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Engine
WARNING: Do not operate the engine with the hood open until the fan blade has been first
examined for possible cracks and separation.
The 4.6L (4V) (281 CID) Cobra engine is a V- 8 with the following features:
z intercooled supercharger
z dual overhead camshafts
z four valves per cylinder
z sequential multiport fuel injection (SFI)
z an aluminum intake manifold
z aluminum cylinder heads
z a cast aluminum, 90-degree V- cylinder block
z individually chain- driven camshafts with a hydraulic timing chain tensioner on each timing chain
z the electronic ignition system with eight ignition coils
Identification
Always refer to these labels when replacement parts are necessary or when checking engine
calibrations. The engine parts often differ within a CID family. Verification of the identification codes will
ensure that the correct parts are obtained. These codes contain all the pertinent information relating to
the dates, optional equipment and revisions. The Ford Master Parts Catalog contains a complete
listing of the codes and their application.
Code Information
The engine code information label, located on the side of the valve cover and the front side of the
valve cover, contains the following:
zengine build date
z engine plant code
z engine code
Exhaust Emission Control System
Operation and necessary maintenance of the exhaust emission control devices used on this engine is
covered in the Powertrain Control/Emissions Diagnosis (PC/ED) manual.
Induction System
The sequential multiport fuel injection (SFI) provides the fuel/air mixture needed for combustion in the
cylinders. The eight solenoid- operated fuel injectors:
z are mounted in the lower intake manifold.
z meter fuel into the air intake stream in accordance with engine demand.
SECTION 303-
01C: Engine — Cobra 4.6L (4V) 2003 Mustang Workshop Manual Klj . 1 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9 6268 Timing chain (2 req'd)
10 6M256 Timing chain guide
11 6L266 Timing chain tensioner
12 6L253 Timing chain tensioner arm
13 6268 Timing chain (2 req'd)
14 N804958 Bolt (2 req'd)
15 6B274 Timing chain guide
16 N606527 Bolt
17 19D269 A/C compressor
18 N806184 Bolts (3 req'd)
19 6306 Crankshaft sprocket
20 6L253 Timing chain tensioner arm
21 12A227 Ignition pulse ring
22 6C086 Engine front cover
23 N806177 Bolts (8 req'd)
24 N806300 Studs (5 req'd)
25 6700 Crankshaft front seal
26 6316 Crankshaft pulley
27 N806165 Washer
28 W701512 Stud
29 8A528 Water pump pulley
30 N806282 Bolts (4 req'd)
31 N806177 Bolts (4 req'd)
32 8501 Water pump
33 N808102 Bolt
34 19A216 Belt idler pulley
35 N804178 Nut
36 N806300 Harness support bracket
37 N806300 Stud
38 N806155 Bolt
39 6C315 Crankshaft position sensor
40 N806155 Bolt
41 6B288 Camshaft position sensor
42 N808920 Bolts (3 req'd)
43 6C254 Crankshaft extension support pulley
44 10153 Lower support bracket
45 N605909 Bolts (2 req'd)
46 8620 Accessory drive belt
47 N811268 Bolt
48 8B603 Belt idler bracket support
49 N808198 Stud
50 Klj . 8 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

8 6B277 Camshaft bearing cap
9 — Bolt (24 req'd)
10 6A271 Camshaft
11 6529 Roller follower (8 req'd)
12 6C501 Hydraulic lash adjuster
13 6065 Bolt (20 req'd)
14 6A273 Camshaft
15 6B278 Camshaft bearing cap (2 req'd)
16 9448 Exhaust manifold gasket
17 9F485 EGR valve tube to manifold connector
18 W701706 Nut (8 req'd)
19 9431 Exhaust manifold
20 6C324 PCV tube
21 6A505 Valve cover
22 N808199 Bolt (20 req'd)
23 6766 Oil filler cap
24 12A366 Ignition coils
25 6P068 Ignition coil cover
26 N807309 Bolt (4 req'd)
27 6050 Cylinder head Klj . 10 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...