radio antenna FORD MUSTANG 2003 Workshop Manual

z
Did any abnormal occurrence coincide with or proceed its appearance?
Use the information gained from the customer to accurately begin the diagnostic process.
Pre- Drive Check
It is important to do a pre- drive check before road testing the vehicle. A pre- drive check verifies that
the vehicle is relatively safe to drive and eliminates any obvious faults on the vehicle.
The pre- drive check consists of a brief visual inspection. During this brief inspection, take note of
anything that will compromise safety during the road test and make those repairs/adjustments before
taking the vehicle on the road.
Preparing for the Road Test
Observe the following when preparing for the road test:
zReview the information recorded on the NVH Diagnostic Guide. It is important to know the
specific concern the customer has with the vehicle.
z Do not be misled by the reported location of the noise/vibration. The cause can actually be
some distance away.
z Remember that the vibrating source component (originator) may only generate a small
vibration. This small vibration can in turn cause a larger vibration/noise to emanate from another
receiving component (reactor), due to contact with other components (transfer path).
z Conduct the road test on a quiet street where it is safe to duplicate the vibration/noise. The ideal
testing route is an open, low- traffic area where it is possible to operate the vehicle at the speed
in which the condition occurs.
z If possible, lower the radio antenna in order to minimize turbulence. Identify anything that could
potentially make noise or be a source of wind noise. Inspect the vehicle for add- on items that
create vibration/noise. Turn off the radio and the heating and cooling system blower.
z The engine speed is an important factor in arriving at a final conclusion. Therefore, connect an
accurate tachometer to the engine, even if the vehicle has a tachometer. Use a tachometer that
has clearly defined increments of less than 50 rpm. This ensures an exact engine speed
reading.
Verify the Customer Concern
Verify the customer concern by carrying out a road test, an engine run- up test, or both.
The decision to carry out a road test, an engine run- up test, or both depends on the type of NVH
concern. A road test may be necessary if the symptom relates to the suspension system or is sensitive
to torque. A drive engine run- up (DERU) or a neutral engine run- up (NERU) test identifies noises and
vibrations relating to engine and drivetrain rpm. Remember, a condition will not always be identifiable
by carrying out these tests, however, they will eliminate many possibilities if carried out correctly.
Road Test Klj . 5 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Audio System
Refer to Wiring Diagrams Cell
130 , Radio for schematic and connector information.
Inspection and Verification 1. Verify the customer concern by operating the electronic audio system with the engine running.
2. Visually inspect the following for obvious signs of mechanical and electrical damage.
3. If the concern remains and the fault is not detected, proceed to the Symptom Chart to continue diagnostics.
Symptom Chart SECTION 415-
00: Entertainment System — General Information 2003 Mustang Workshop Manual Special Tool(s)
73III Automotive Meter
105-
R0057 or equivalent
Visual Inspection Chart Mechanical Electrical
z
Audio unit
z Antenna or antenna cable
z Speakers mounting/speaker cones
z Radio ignition interference capacitor, radio frequency
interference suppression bond or radio receiver hood bonding
strap cleanliness z
Battery junction box
(BJB) fuses:
„3 (40A)
„ 4 (40A)
„ 6 (40A)
z Central junction box
(CJB) fuses:
„6 (20A)
„ 27 (25A)
„ 32 (15A)
z Ignition switch
z Circuitry
z Audio unit
Symptom Chart Condition
Possible Sources Action
z The audio unit is
inoperative/does not operate z
Central
junction box z
Go To Pinpoint Test A . Klj . 1 ba
242003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST B: POOR RECEPTION z
Are the resistances less than 5 ohms? system for normal
operation.
No
REPAIR the circuit
(s) in question. TEST
the system for
normal operation.
Test Step Result / Action to Take
B1 CHECK ANTENNA CABLE
CONNECTIONS z
Key in OFF position.
z Check the antenna connections
including the extension cable.
z Check to make sure the antenna is
securely mounted to the vehicle body
at ground points.
z Are the connections clean, secure,
and in metal- to-metal contact? Yes
GO to
B2 .
No
CLEAN and SECURE the antenna connections
as necessary. TEST the system for normal
operation. B2 CHECK SUPPRESSION
EQUIPMENT/MOUNTING AND
CONNECTING CIRCUITS z
Check all necessary suppression
equipment and the radio frequency
interference suppression bond. Refer
to Section 415 - 01 .
z Check the radio receiver hood bonding
strap and the body- to-chassis straps
for integrity, cleanliness, and metal- to-
metal contact.
z NOTE: The capacitor mounting points
are used to complete the electrical
circuit and must be mounted securely
to clean surfaces.
z Check the mounting and connecting
circuits of the radio ignition interference
capacitor for integrity, cleanliness, and
metal- to-metal contact.
z Are the connections clean, secure,
and in metal- to-metal contact? Yes
GO to
B3 .
No
CLEAN, SECURE, or INSTALL new suppression
equipment as necessary. TEST the system for
normal operation. B3 CHECK RADIO IGNITION
INTERFERENCE CAPACITOR z
Check the operation of the radio
ignition interference capacitor by
substituting it with a known good
component.
z Key in START position.
z Turn the audio unit on and check the
radio reception. Yes
INSTALL a new radio ignition interference
capacitor. TEST the system for normal operation.
No
GO to
B4 . Klj . 5 ba
242003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Is the noise eliminated? B4 CHECK GENERATOR
z
Key in OFF position.
z Check the generator by disconnecting
the wiring from the voltage regulator.
z Key in START position.
z Turn on the audio unit and check the
radio reception.
z Is the noise eliminated? Yes
INSTALL a new generator. REFER to
Section 414 - 02 . TEST the system for normal operation.
No
GO to B5 .
B5 CHECK IGNITION CIRCUITS
z
Key in OFF position.
z Check the ignition circuits for correct
routing, grounding, and integrity of
connections.
z Are the ignition components OK? Yes
GO to
B6 .
No
REPAIR the ignition system as necessary. TEST
the system for normal operation. B6 SUBSTITUTE ANTENNA
z
Substitute a known good antenna.
Ground the antenna base to an
unpainted metal surface on the vehicle.
z Key in START position.
z Verify the operation of the audio unit.
z Is the noise eliminated? Yes
INSTALL a new antenna. TEST the system for
normal operation.
No
GO to
B7 .
B7 SUBSTITUTE ANTENNA CABLE
z
Key in OFF position.
z Substitute a known good antenna
cable.
z Key in START position.
z Verify the operation of the audio unit.
z Is the noise eliminated? Yes
INSTALL a new antenna cable. TEST the system
for normal operation.
No
GO to
B8 .
B8 SUBSTITUTE AUDIO UNIT
z
Key in OFF position.
z Substitute a known good audio unit.
z Key in START position.
z Verify the operation of the audio unit.
z Is the noise eliminated? Yes
REMOVE the audio unit and SEND it to an
authorized Ford audio system repair facility.
TEST the system for normal operation.
No
GO to
B9 .
B9 SUBSTITUTE SUBWOOFER
AMPLIFIER z
Key in OFF position.
z Substitute a known good subwoofer
amplifier.
z Key in START position.
z Verify the operation of the audio unit.
z Is the noise eliminated? Yes
REMOVE the subwoofer amplifier and SEND it to
an authorized Ford audio system repair facility.
TEST the system for normal operation.
No
GO to
B10 .
B10 REPOSITION COMPONENTS
z
Key in OFF position.
z Determine if the noise can be
eliminated by repositioning the antenna
cable, speaker circuits, or audio unit
power feed circuits away from other
circuits or brackets.
z Key in START position.
z Verify the operation of the audio unit. Yes
Permanently REPOSITION the components as
needed. TEST the system for normal operation.
No
GROUND various parts (for example, engine,
fenders, quarter panels, stone deflectors, body
sheet metal) of the vehicle to the frame using a Klj . 6 ba
242003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Antenna
The antenna system consists of:
zantenna mast
z antenna base and cable
z antenna lead- in cable
The radio antenna uses a two- piece coaxial cable to connect the audio unit to the antenna. The front
antenna lead- in cable is connected to the audio unit and has an in- line connector at the RH cowl side.
SECTION 415-
02: Antenna 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Antenna
Removal
1. Lower the glove compartment by releasing the stops from the instrument panel.
2. Disconnect the antenna in- line connector.
3. Remove the antenna base and cable. 1. Remove the radio antenna base cap.
2. Remove the screws.
3. Remove the antenna base and cable.
z Disconnect the antenna cable grommet.
Installation 1. To install, reverse the removal procedure.
SECTION 415-
02: Antenna 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Anti-
Theft — Passive Anti- Theft System (PATS)
The passive anti- theft system (PATS) contains the following components:
z theft indicator
z encoded ignition key
z transceiver module
z instrument cluster
z powertrain control module (PCM)
z standard corporate protocol (SCP) communication network
The PATS uses radio frequency identification technology to deter a driveaway theft. Passive means
that it does not require any activity from the user. This system is known as SecuriLock® in North
America, Safeguard® in the U.K. and PATS in continental Europe. This information can be found in
owners literature.
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently
installed electronic device called a transponder. Each transponder contains a unique electronic
identification code, with over 72 million billion combinations.
Each encoded ignition key must be programmed into the vehicle's instrument cluster (the instrument
cluster is also known as a hybrid electronic cluster [HEC]), before it can be used to start the engine.
There are special diagnostic procedures outlined in the workshop manual that must be carried out if
new encoded ignition keys are to be installed.
The encoded key is larger than a traditional ignition key. The key does not require batteries and should
last the life of the vehicle.
The transceiver module communicates with the encoded ignition key. This module is located behind
the steering column shroud and contains an antenna connected to a small electronics module. During
each vehicle start sequence, the transceiver module reads the encoded ignition key identification code
and sends the data to the instrument cluster.
The control functions are contained in the instrument cluster. This module carries out all of the PATS
functions such as receiving the identification code from the encoded ignition key and controlling engine
enable. The instrument cluster initiates the key interrogation sequence when the vehicle ignition switch
is turned to RUN or START.
The PATS uses the PCM to enable or disable the engine. The instrument cluster communicates with
the PCM over the SCP network in order to enable engine operation. The instrument cluster and the
PCM use sophisticated messages in order to prevent a theft. The instrument cluster and the PCM
share security data (when first installed together) that makes them a matched pair. After this security
data sharing, these modules will not function in other vehicles. The shared PCM ID is remembered
even if the battery is disconnected. The instrument cluster also stores the vehicle's key identification
code even if the battery is disconnected. There are special diagnostic procedures outlined in this
workshop manual that may be carried out if either a new instrument cluster or PCM needs to be
installed.
All elements of PATS must be functional before the engine is allowed to start. If any of the components
are not working correctly, the vehicle will not start.
PATS uses a visual theft indicator. This indicator will prove out for three seconds when the ignition SECTION 419-
01: Anti-Theft — PATS 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...