ignition GEELY CK 2008 Repair Manual

253Yes: continue with next step.
No: check the circuit, repair it and continue with step (5).
8Turn the ignition switch to LOCK.
9Check the continuity of the terminal of instrument connector and that of diagnostic interface (check the
two ends of K line).
Yes: continue with next step.
No: repair or replace the wire harness. Continue with step (5).
VMake sure to disconnect the negative terminal cable from the battery and wait for at least 60s.Disconnect
the ECU connector. 11Disconnect the connectors of the instrument cluster 12 Are the connector terminals 5, 7 and 9 and those of instrument cluster continuity?
Yes: continue with next step.
No: replace the wire harness, and then continue with step (5). 13Remove ECU and see whether the terminals are in good condition and whether the shorting bar is
broken.
Yes: replace the ECU.
No: reconnect the ECU connector, and then continue with next step.
(3) Make sure of the nonrecurrence of the trouble after repair
1Turn the ignition switch to LOCK.
2Disconnect the negative (-) terminal cable from the battery and wait for at least 60s.
3Connect all the ECU connectors.
4Connect the connector of driver airbag assembly.
5Connect the connector of passenger airbag assembly.
6Connect the connectors of driver and passenger seat belt pretensioners (vehicle with pretensioner).
7Connect clock spring connector.
8Connect the negative (-) terminal cable of the battery.
9Turn the ignition switch to ON.
VIs the SRS warning light working normal?
Yes: the trouble is eliminated. Explain the repair procedures to the Customer.
No: recheck symptoms of the trouble. Repeat these procedures from the first step if the trouble reoccurs.

2543.Internal trouble
4. Power troubleDIAGNOSTIC PROCEDURES(1) Check battery
yIs the battery voltage measured higher than 9V?
Yes: continue with next step.
No: low battery voltage, check the charging/discharging system.
ySee Chapter I, Charging System-Battery Checking
(2) Check the wire harness between battery and fuse box
yRemove fuse box and turn the ignition switch ON, without loosening connector.
yMeasure and see if the electrical potential between two terminals of the fuse box is more than 9V.
Yes: continue with next step.
No: check the wire harness.DTC B1620 Internal trouble of SRS unitCAUTION
●
Condition for running the DTC is to inspec t the dia gnostic trouble code that
ma y not a ppe a r prior to this te st. P e rforming this te st ma y re sults in body injury orda ma ge d system due to misoperations. The re fore , prepa ra tions must be ma debefore checking.
●
Internal circuit trouble of SRS ECU
P ossible Ca use Interna l trouble of SRS unit
Operation
Replace the SRS unit, see SRS System, Removal & Installation of SRS Unit Che c king ConditionsDTC B1112 Low power source voltage of SRS ECU
CAUTION
Condition for running the DTC is to inspe ct the diagnostic trouble c ode that ma y not
a ppea r prior to this test. P e rforming this te st ma y re sults in body injury or da ma ge dsyste m due to misoperations. Therefore, prepa ra tions must be ma de beforechecking.
●
The e lec tric a l pote ntia l be twe e n pins 5 a nd 6 of the c onne c tor of SRS unit is
le s s t ha n 9V .
●
Low batte ry volta ge
Trouble in wire ha rne ss betwe e n ba tte ry and SRS ECU C he c king C ondit ions
P os s ible C a us e

255(3) Check the wire harness between the fuse box and the connector of the SRS unit
CAUTION
If it is not handled properly, the airbag assembly may be triggered and deployed, leading to serious injury to a
person. Therefore, prior to handling, read the service cautions carefully. See service cautions for SRS.
1Turn the ignition switch to LOCK.
2Loosen the negative (-) terminal cable from the battery and wait for over 1 minute.
3Remove steering column hood.
4Loosen the connector of the clock spring.
5Remove glove box (along with passenger airbag assembly)
6Loosen passenger airbag assembly connectors.
7Remove left trim plate.
8Loosen all the SRS unit connectors.
9Reconnect the negative (-) terminal cable of the battery and turn ignition switch ON, check whether the
electrical potential between pins 5 and 6 (ground) of the connector of SRS unit is higher than 9V.
Yes: continue with next step.
No: replace the wire harness.
VTurn the ignition switch to LOCK. 11 Loosen the negative (-) terminal cable from the battery and wait for over 1 minute. 12 Remove left trim plate. 13 Disconnect the adaptor connector of SRS unit. 14 Reconnect the battery negative (-) terminal cable and turn the ignition switch ON, check whether the
voltage between the corresponding pin of the connector and the pin (ground) is higher than 9V.
Yes: completion of trouble diagnosis.
No: replace the wire harness.
5. Driver side troubleDTC
B1 346
B1 347
B1 348
B1 349
CAUTION
● If it is not handled properly, the airbag assembly may be triggered and deployed,leading to s erious injury to a person. Therefore, prior to handling, read the service cautionscarefu lly .
See s erv ice cau t io n s fo r SRS
If there is driver airbag
● The resistance between terminals of the SRS unit connectors is out of range.
The wire harness of the driver airbag of SRS is short or open circuited.
● Driv er airb ag as s emb ly tro u ble.
● Clock spring internal trouble.
● Trouble of the connector of the circuit between clock spring and SRS ECU.
● The wire harness between clock spring and SRS ECU is open or short-circuited.
● In co rrect in s ert io n o f t h e co n n ect o r o f t h e d riv er airb ag g en erat o r o f SRS. Driver airbag trouble (high or low resistance, short circuit, ground, etc.)
Ch e c kin g Co n d it io n s
Pos s ib le caus e

256DIAGNOSTIC PROCEDURES
(1) Check clock spring
CAUTION
If it is not handled properly, the airbag assembly may be triggered and deployed, leading to serious injury to a
person. Therefore, prior to handling, read the service cautions carefully.
See service cautions for SRS.
yDo the related parts of the clock spring work normal? (Are the pins correctly correlated? There should
be no unnecessary short or open circuit, etc). If possible, use a new clock spring to replace the present
one.
Normal: continue with next step.
Abnormal: replace the clock spring.
See SRS-Clock Spring, Removal & Installation.
(2) Ascertain the trouble exists in driver airbag assembly or other parts
1Replace with a new driver airbag assembly.
2Reconnect the negative (-) terminal cable of the battery.
3Turn the ignition switch ON.
4Any DTC displayed? Can it be cleared?
Yes: replace the driver airbag assembly.
See SRS- Driver Airbag Assembly, Removal & Instillation.
No: continue with next step.
(3) Check the connector of clock spring wire harness
1Turn the ignition switch to LOCK.
2Loosen the negative (-) terminal cable from the battery and wait for over 1 minute.
3Remove steering column hood.
4Loosen the connector of the clock spring.
5Are the connectors of the clock spring normal? (Are the pins correctly correlated? There should be no
unnecessary short or open circuit, etc). If possible, use a new clock spring to replace the present one.
Normal: continue with next step.
Abnormal: replace the wire harness.
See SRS-Clock Spring, Removal & Installation.
(4) Check the wire harness between clock spring and SRS ECU
1Turn the ignition switch to LOCK.
2Loosen the negative (-) terminal cable from the battery and wait for over 1 minute.
3Remove glove box (along with passenger airbag assembly).
4Loosen passenger airbag assembly connectors.

2581Turn the ignition switch to LOCK.
2Loosen the negative terminal cable from the battery and wait for over 1 minute.
3Remove the glove box.
4Loosen the passenger airbag assembly connectors.
5Is the connector of the passenger airbag assembly normal?
Normal: [DTC of present trouble]
Continue with next step.
[DTC of past trouble]
Continue with next step.
Abnormal: replace the wire harness.
(3) Ascertain the trouble exists in passenger airbag assembly or other part
1Connect a new assembly to terminals A and B of the connector of passenger airbag assembly.
2Connect the negative (-) terminal cable of the battery.
3Turn the ignition switch ON.
4Any DTC displayed? Can it be cleared?
No: continue with next step.
Yes: replace passenger airbag assembly
See SRS- Passenger Airbag Assembly, Removal & Installation.
(4) Check the wire harness between passenger airbag assembly and SRS ECU
1Turn the ignition switch to LOCK.
2Loosen the negative (-) terminal cable from the battery and wait for over 1 minute.
3Remove steering column hood.
4Loosen the connector of the clock spring.
5Loosen the connectors of driver and passenger airbag assemblies.
6Remove left trim plate.
7Loosen all the SRS unit connectors.
8Check the circuit between the connector terminals of the SRS ECU and that of passenger airbag assembly
and the circuit between the connector terminal of the SRS unit and that of passenger airbag assembly for
the following:
yGround.
yShort circuit with power source.
yOpen circuit.
9Are the above-mentioned wire harnesses normal?
Normal: completion of trouble diagnosis.
Abnormal: replace the related wire harness.

262Section 3 Removal & InstallationI. SRS ELECTRONICAL CONTROL UNIT (ECU)1. Operations prior to Removal
(1) Turn the ignition switch OFF.
(2) Remove negative (-) terminal cable of the battery. Put it in a proper position or wrap it up with insulating
tape.
2. Removal procedures:
(1) Remove the central passage side cover plate (or remove auxiliary console).
(2) Remove the connectors to SRS ECU.
(3) Remove ECU.
3. Installation procedures:
(1) Install ECU.
(2) Install the connectors to SRS ECU.
(3) Install the central passage side cover plate (or install auxiliary console).
(4) Connect negative (-) terminal cable of the battery.
4. Key points for Installation:
(1) Install ECU.
(2) Check after installation.
1Turn the ignition switch ON.
2The warning light goes on within 6s, and then goes out.
(3) If the light doesn't go out, check the trouble and eliminate it.NOTICE1. Work must be started 60s after the negative (-) terminal cable is detached from battery. The detachednegative (-) terminal cable shall be protected with insulating tape for insulation.
2. Never attempt to dismantle or repair an ECU. If there is any trouble, replace the ECU with a new one.
3. Prevent the ECU from shock or vibration. If pitting, crack or distortion is found, replace the ECU with
a new one.
4. Every time an airbag is deployed, the ECU shall be replaced with a new one.
5. When disassembling or maintaining the parts around ECU, attention must be given to avoid contacting
the ECU.NOTICE
If the ECU cannot be installed correctly, the airbag will not act normally.

2635. Check:
1 ECU case for pitting, crack and distortion.
2 The joint for damage and distortion.
For other ECU checkings, see Troubleshooting.II. AIRBAG ASSEMBLY & CLOCK SPRING1. Operations prior to removal
(1) Take out the ignition key after the steering wheel and front wheel are adjusted to straightforward direction.
(2) Remove negative (-) terminal cable from the battery.
2. Removal procedures of the driver airbag assembly:
(1) Unscrew the screws of the two sides.
(2) Disconnect the connector of the wire harness.
(3) Remove the components of airbag assembly.
(4) Remove steering wheel.
3. Removal procedures of clock spring:
(1) Remove the driver airbag assembly (disconnect the connector).
(2) Remove steering wheel gently (see the precautions).
(3) Open the upper closure of the combination switch, locate and
disconnect the connector of wire harness in the lower end.
(4) Remove clock spring from the steering wheel.
4. Installation procedures of the driver airbag assembly
(1) Pre-Check
ySteering wheel
yConnect the wire harness
yDriver airbag assembly
(2) Screw up the installation screws of the two sides.
(3) Connection of the negative (-) terminal of the battery
(4) Check after installation.NOTICE
If pitting, crack or distortion is found on an ECU, replace it with a new one.NOTICE
Put the removed driver airbag
assembly upside down in a clean
and dry place for care.NOTICE
Put the removed clock spring in
a clean and dry place for care.

265III. KEY POINTS FOR INSTALLATION1. Pre-Check
(1) The new airbag or clock spring shall be checked before being installed.
(2) Connect negative (-) terminal cable of the battery.
(3) Connect Hi-DS T to the diagnostic interface (16 connector).
(4) Turn the ignition switch ON.
(5) Read the diagnostic circuit and see if the other locations than the troubled area of the airbag are normal.
(6) Turn the ignition switch ON.
(7) Remove the negative (-) terminal cable from the battery, and protect it with insulating tape for insulation.
2. Installation of clock spring: align the clock spring and install it to the
steering wheel.
yCenter alignment of the clock spring
Screw up the clock spring clockwise to the end, rotate it counterclock-
wise by 2.5 turns, and align it with the mark (see the figure below).
3. Install the components of the steering wheel and airbag assembly
(1) When the center of the clock spring is aligned, install the components of the steering wheel and airbag
assembly.
(2) After being installed, rotate the left and right sides of the steering wheel to position, and make sure there
is no abnormality.NOTICEIn case of scrapping an airbag, it shall be noted that the airbag shall be deployed according to the specifiedprocedures before being scrapped.
When connecting or disconnecting the Hi-DS T, turn the ignition switch OFF first.NOTICE:
Work must be started 60s after the negative (-) terminal cable is disconnected from battery.NOTICE:
If the center of the clock spring cannot be aligned, the steering wheel
will not turn midway, or cause bad performance to the clock spring
circuit, consequently hamper the normal action of the airbag.NOTICEWhen installing the components of the steering wheel and airbag assembly, attention should be given toprotect the wire harness of the clock spring from seizure.

2664. Check after installation
(1) Slightly rotate the steering wheel left and right, make sure that there is no abnormality or noise. (Driver
airbag module, clock spring)
(2) Turn the ignition switch ON.
(3) The warning light goes on within 6s, and then goes out.
(4) The trouble shall be eliminated if the warning light remains on when the ignition switch is turned on or
after it goes out after 6s.IV. CHECKING1. Driver airbag assembly checking
Check the following items and replace the related components of the airbag assembly if any badness is
found. The old components shall be deployed before scrapping.
(1) Check the hood for pitting, crack, distortion, etc.
(2) Check the joint of the wire harness for damage and the terminal for distortion.
(3) Check the case of the gas generator for pitting, crack and distortion.
(4) Check the installation status of the airbag assembly.
2. Check the clock spring
Check the following items, and replace the clock spring if any badness is found.
(1) Check the joint and protecting tube for damage and the terminal for distortion.
(2) Check the case for damage.
(3) Check and see if the joint terminal at the upper end of the clock spring are in conduction with that at the
lower end.
(4) A thin probe shall be inserted from the back of the yellow connector of the clock spring.NOTICE
If there is pitting, crack or distortion, replace the airbag assembly with new one. The old components of the
airbag shall be deployed before scrapping.
The circuit resistance of the airbag assembly (squib) cannot be measured even with a designated tester.Since there is current flowing in the squib, when a tester is involved in measuring the resistance, sometimesthe airbag is unexpectedly deployed in case of static electricity, leading to serious accident.

272Chapter 8 MK-20 ABS SystemSection 1 ABS DiagnosisI. Check the ABS Warning Light1. Check the ABS Warning Light goes on as the following:
1Turn the ignition switch to ON, the ABS Warning Light goes on for about 1.7 seconds and then goes off.
2If the above condition is not satisfied, it indicates that there is a fault, please check the DTC.
3If the warning light does not light up at all, refer to the Non-DTC fault inspection table.II. The Reading of the information statusAfter connecting the scan meter, turn the ignition switch to¡°ON¡±, select the function menu item 01, press
OK to confirm, the screen will display the following information:
1. ECU drawing number and its version:
ABS MK20 IE
2. Code 01901III. Read and Clear the DTC1. After selecting the "02 Read DTC" in the function menu, it displays the total amount of the fault, if there
is no DTC, then it displays no DTC. Then, press OK button to proceed to next page to review the DTC
and its description. Generally, there is a P or O before the DTC, indicating that it is a Persistent fault or
Occasional fault. Persistent fault remains existing all the time, while the Occasional fault can be cleared
and is only able to reoccur during the driving.
Note:
The reading of the DTC can not be quitted middle way, you can return to the function menu only
after reading all the DTC.
Clear DTC
2. Select function menu item 05, press OK button to clear the DTC, if the DTC can not be cleared, it
indicates that the DTC represent exist all the time, if the saved DTC can be cleared, it indicates that it is
occasional fault can only be detected during the driving.