GEELY FC 2008 Workshop Manual

Windshield/bodywork glass/wing mirror--Electric window control system
Switch position avometer terminalssituations
UP 4-5, 2-3conduction
OFF 4-5, 1-3conduction
DOWN 2-5, 1-3conduction
Battery terminals working direction
Battery anode lead-terminal 5 main driving axis working
Battery cathode lead-terminal 4 as clockwise
Battery anode lead-terminal 4 main driving axis working
Battery cathode lead-terminal 5 as anticlockwise
2. Inspect electric window switch assembly
Active switch, inspect the conduction among the joint terminals.
If the conduction does not limit to regulations, replace electric
window main switch.
3. Inspect left rear electric window motor assembly.
(a) Inspect the function of left rear electric window assembly.
(1) Inspect whether the motor works calmly.
4. Inspect electric window shift relay [67000061]
Check the conduction of relay (mark: P/W)
If the conduction does not limit to regulations, replace relay.
 320 
Conditionsavometerregular situations
Always 1-2conduction
Supply battery voltage
To that between terminal 13-5 conduction
and terminal 2

Windshield/bodywork glass/wing mirror--Front windscreen
Front windscreen
Change
Clues on: Please assemble as the disassembly opposite sequence. Assemble directions could
be got when necessary.
1. Disassemble right front pillar trim board assembly [68010017] (referring to page 390)
2. Disassemble left front pillar trim board assembly [68010014] (referring to page 390)
3. Disassemble inner rear mirror assembly [67010013] (referring to page 390)
4. Disassemble right sun shade [68010085] (referring to page 390)
5. Disassemble left sun shade [68010084] (referring to page 390)
6. Disassemble interior front headlamp assembly [67010075] (referring to page 390)
7. Disassemble passenger handle (referring to page 390)
8. Disassemble sun shade pothook [68010086] (referring to page 390)
9. Disassemble top interior trim board
Disassemble top interior trim board
10.Disassemble top left trim tape [68000128]
11. Disassemble top right trim tape [68000129]
12. Disassemble front windscreen sealed trim board [68000062]
(a) Use blade to cut trim tape as the drawing.
Note: Do not cut the bodywork.
(b) Disassemble rudimental trim type.
steel wire
 321  13. Disassemble front windscreen assembly [68000061]
(a) Use a steel wire to drill through windows and bodywork.
(b) Tie something like wood block at both the end of steel wire.
Clues on: Stick adhesive tape on the bodywork at work
to prevent paintwork from scraping.
Clues on: When separate window, do not damage
paintwork and interior trim board. When disassemble
front windscreen,put a plastic board between steel wire
and panel to prevent scratching the panel.
(c) Pull steel wire along front windscreen around, remove
agglutinant.
(d) Disassemble front windscreen.
Note: When cut front windscreen down, leave aggluti-
nant as much as possible on the bodywork.
14.Clean front windscreen assembly [68000061]
Use white gasoline to clean front windscreen around.
15. Assemble windscreen orientation plastic button

Windshield/bodywork glass/wing mirror--Front windscreen
Assemble two orientation block on the windscreen as the
drawing.
A: 40mm
B: 8mm
16. Assemble front windscreen in board sealed tape
[68000063]
Stick sealed tape with double faced adhesive tape on both
sides.
a: 7mm
b: 22.5mm
c: 45mm
d: 5mm
17. Assemble front windscreen assembly [68000061]
(a) Put front windscreen at the right position.
(b) Inspect the contacting part of front windscreen brim whether
it is flat
(c) Mark signal between bodywork and glass.
(d) Disassemble front windscreen .
(e) Use blade to remove granulation area.
Note: leave agglutinant as much as possible on the
bodywork.
(f) Use duster cloth with cleaner to clean the agglutinant on
the incision.
Clues on: When all the agglutinant has been removed
completely, clean the bodywork.
(g) Use brush to daub M priming paint on the o contacting part
of bodywork.
Notes:
zDry M priming paint for three minutes.
zDo not daub M priming paint on the agglutinant.
zOpened M priming paint can not use for the next
 322 
Bond
Bond

Windshield/bodywork glass/wing mirror--Front windscreen
 323 
time.
(h) Use brush or sponge to daub G priming paint on the front
windscreen brim and contacting interface.
(i) When daub other areas beside regulations, use clean duster
cloth to clean before priming paint gets dry.
Notes:
zUse G priming paint over three minutes.
zOpened G priming paint can not use for the next
time.
(j) Cut a hole on glue canister sharp mouth
(k) Put the glue canister in the sealed glue jet gun.
(l) Daub agglutinant on the front windscreen.
A: 12mm
B: 8mm
18.Assemble front windscreen sealed trim tape
[68000062]
Assemble the new trim tape in the bodywork manually.
19. Inspect water leakage and repair
(a) Actualize water leakage after hardening.
(b) Use agglutinant to seal leak position.

Windshield/bodywork glass/wing mirror--Rear ventilation window
Rear ventilation window
Change
Clues on: Please assemble by the sequence opposite with disassembling sequence. Assemble
directions could be got when necessary.
1. Disassemble the step trim board of left rear door [68010022] (referring to page 390)
2. Disassemble the step trim board of right rear door [68010024] (referring to page 390)
3. Disassemble left rear door frame sealed tape [68010059]
4. Disassemble right rear door frame sealed tape [68010060]
5. Disassemble rear seat cushion
6. Disassemble rear seat back assembly (fixed) [68010076] (referring to page 354)
7. Disassemble rear seat right back assembly (fixed) [68010079] (referring to page 352)
8. Disassemble rear seat left side back assembly (separate) [68010078](referring to page
352)
9. Disassemble left rear pillar interior trim board assembly [68010026] (referring to page
390)
10. Disassemble right rear pillar interior trim board assembly [68010027] (referring to page
390)
11. Disassemble high brake light assembly [68010008]
12. Disassemble rear platform front-below trim board [68010034]
13. Disassemble rear wind window sealed trim tape [68000104]
(a) Use blade to cut the trim tape as the drawing.
steel wire
 324 
Notes: Do not damage the bodywork by blade.
(b) Disassemble rudimental trim tape.
14. Disassemble rear ventilation window assembly
[68000103]
(a) Use a steel wire to drill through windows and bodywork.
(b) Tie something like wood block at both the end of steel wire.
Clues on: Stick adhesive tape on the bodywork at work
to prevent paintwork from scraping.
Notes: When separate window, do not damage
paintwork and interior and exterior trim board.
(c) Pull steel wire along front windscreen around, removal
agglutinant.
(d) Disassemble front windscreen.
Note: When cut front windscreen down, leave aggluti-
nant as much as possible on the bodywork.
15. Clean rear ventilation window assembly [68000103]
Use white gasoline to clean rear ventilation window around.
16. Assemble windscreen orientation plastic button
[68000064]
Assemble two orientation block on the rear windscreen as the

Windshield/bodywork glass/wing mirror--Rear ventilation window
figure.
A: 40mm
B: 8mm
17. Assemble rear ventilation window inboard sealed
tape [68000105]
Stick sealed tape with double faced adhesive tape on both
sides.
18. Assemble rear ventilation window assembly
[68000103]
(a) Put rear ventilation window at the right position.
(b) Inspect the contacting part of rear ventilation window brim
whether it is flat.
(c) Mark signal between bodywork and glass.
(d) Disassemble rear ventilation window
(e) Use blade to remove coarseness area.
Note: leave agglutinant as much as possible on the
bodywork.
(f) Use duster cloth with cleaner to clean the agglutinant on
the cutting surface.
Clues on: When all the agglutinant has been removed
completely, clean the bodywork.
(g) Use brush to daub M priming paint on the contacting part
of bodywork.
Notes:
zDry M priming paint for three minutes.
zDo not daub M priming paint on the agglutinant.
zOpened M priming paint can not use for the next
time.
(h) Use brush or sponge to daub G priming paint on the front
windscreen brim and contacting interface.
(i) When daub other areas beside regulations, use clean duster
 325 
Bond
Bond

Windshield/bodywork glass/wing mirror--Rear ventilation window
cloth to clean before priming paint gets dry.
Clues on:
zUse G priming paint over three minutes.
zOpened G priming paint can not use for the next
time.
(j) Cut a hole on glue canister sharp nose.
(k) Put the glue canister in the sealed glue jet gun.
(l) Daub agglutinant on the front windscreen.
A: 12mm
B: 8mm
C: 6.5mm
D: 13mm
19. Disassemble rear seat back assembly (fixed)
[68010076] (referring to page 354)
20 Disassemble rear right side back assembly
(separate) [68010079] (referring to page 352)
21. Disassemble rear seat left side back assembly (separate) [68010078] (referring to page
352)
 326 

Windshield/bodywork glass/wing mirror--Fogbroom system
Fog defrost system
Position drawing
Malfunction
All demists (defrosts) do not work
Rear ventilation window Demist (defrost)
do not work
electric rear mirror defrost dose not workcomponents name
1. DEF main relay
2. DEF-IP fuse
3. DEF-m fuse
4. demist switch
5. wiring harness
1. demist wire
2. wiring harness
1. electric rear mirrorreference pages
Malfunction phenomena table
Demist (Defrost)switch
 327 
Demist wire

Windshield/bodywork glass/wing mirror--Fogbroom system
Inspect
1. Inspect the relay
Inspect the conduction of rear window demist(defrost) relay
(mark: DEF)
If the conduction does not accord with the regulations, replace
relay.
 328 
Conditionsavometer terminals regular situations
Always 1-2conduction
Supply battery voltage
between terminal1 and 3-5 conduction
Terminal2

Windshield/bodywork glass/wing mirror--Electric rearview mirror control system
Electric rearview mirror control system(option)
Inspect the vehicle
1. Inspect Electric retractable rearview mirror function
(a) Turn the ignition switch to ACC
(b) Inspect operating electric retractable rearview mirror function, when it at different positions.
(1) When retractable switch at steering position and left/right rearview mirror at steering position either,
press retractable switch, inspect left and right rearview mirrors whether they remove from steering
steering positionretractable
position
Electric
retract-
able
operation
Handle
operation
 329 
position to retraction position and stop at it.
(2) When retractable switch at steering position and left/
right rearview mirror at steering position either, if any one
of the rearmirrors can be pushed back by hand, then
press retractable switch to retractable position, inspect
left and right rearview mirrors whether they remove from
steering position to retraction position and stop at it.
(3) When retractable switch at retractable position and left/
right rearview mirror at steering position either, if any one
of the rearmirrors can be pushed back to steering posi-
tion by hand, then press retractable switch to retract-
able position , inspect whether rearview mirrors move to
restricted position only in steering position and stop at
it.
(4) When retractable switch at retractable position and left/
right rearview mirror at retractable position either, inspect
left and right rearview mirrors whether they remove from
retraction position to steering position and stop at it.
(5) When retractable switch at retractable position and left/
right rearview mirror at retractable position either, if any
one of the rearmirrors can be pushed back to steering
position by hand, then press retractable switch to steer-
ing position, inspect whether rearview mirrors move from
restricted position to steering position and stop at it.
steering positionretractable
position
Electric
retract-
able
operation
Handle
operation Electric
retract-
able
operationElectric
retract-
able
operation
Electric
retract-
able o
perationsteering positionretractable
position
steering positionretractable
position