ignition GEELY FC 2008 Repair Manual

Circuitry--Power supply
24. spare
25. OBD discharge test system
26. rear fog light
27. Anti-burglary
28. DOOR center control, light con-
trol system
29. Defrost load
30. spare
31. spare
32. eletric injection system, safety
airbag system, anti-burglary
system, instrument system
33. spare
34. spare
35. spare
36. front fog light
37. AMI ignition system
38. TAILposition light, number platelight
39. brake light
40. electric sunroof
41. instrument system, air condition
system, defrost system, Re-
verse Radar, rear light, turn light.
42. CIG air condition system, audio
system, electric rear view mirror,
cigarette lighter
43. washer
44. spare
45. wiper
46. spare
47. center control, light control
system, anti-burglary system,
ABS system
48. air condition system
49. rear defrost system
50. electric glass operator
 315 

Windshield/bodywork glass/wing mirror--Electric window control system
Right front door electric
window generator
Electric window
switch
Right front door electric
window liftElectric window
switch
Right rear door electric
windows lift
Right rear door electric
window generator
Left rear door electric
window generator Left rear door electric
window lift Electric window
switch Left front door electric
window generatorElectric window
main switch
Left front door electric
window lift
Windshield/window glass/wing mirror
Electric window control system
Position drawing (For reference only)
Inspect the car
1. Inspect electric window
(a) Inspect basic function (manual operation function)
(1) Turn the ignition switch to ON
(2) Inspect the window whether it descends when you press electric window switch. Pull the switch up
and inspect whether it ascends.
(3) Inspect the window whether it descends when you press electric window switch of every door. Pull
the switch up and inspect whether it ascends.
 317 

Windshield/bodywork glass/wing mirror--Electric window control system
Avometer terminalsconditionsregular situations
16-earth(input +B signal)turn ignition switch from OFF to ON 0V → 10-14V
11-earthalways conduction
12-earthalways conduction
15-earth(input IG signal)turn ignition switch from OFF to ON 0V→10-14V
(4) Inspect other windows whether they can not actuate except window of driver seat room, when the
electric window switch locked.
2. Inspect automation function
(a) inspect basic function
(1) Turn the ignition switch to ON
(2) Inspect whether driver seat window automatic descends completely, when you press electric win-
dow main switch.
(3) Inspect whether driver seat window stop descending when driver seat window automatic descends
and press the main switch.
If the voltage and conduction do not accord with the regulations, the input side of electric window main
switch may have malfunction.
(b) Inspect the joint terminal voltage when connect the joint.
If the voltage does not accord with the regulations, electric window main switch may have malfunction.
(c) Inspect whether AUTO headlamp(LED) lights when connect the joint, turn the ignition switch from
OFF to ON.
 318 
Avometer terminalsconditionsregular situations
4-earth turn the ignition switch to ON, turn Driver
seat0V→over 9V
(output P/W.UP) Main switch from OFF to UP (manual operation)
9-earthturn the ignition switch to ON, turn Driver
seat0V→over 9V
(output P/W.DOWN)Main switch from OFF to DOWN (manual operation)
9-earthturn the ignition switch to ON, turn Off Driver
seat
window → driver seat Main switch to DOWN 0V→over9V→0V
(output P/W.DOWN)
(auto Operation)
→ windows open completely.
3. Inspect electric window main switch assembly
(a) Inspect operations
(1) Disassemble the joint of driver seat electric window main
switch and inspect the voltage and conduction among
terminals.

Switch position
UP
OFF
DOWNright front, avometer
terminal
4-15, 6-10
4-10, 6-10
6-15,4-10right rear, avometer
terminal
9-15, 7-10
9-10, 7-10
7-15, 9-10Left rear, avometer
terminal
3-15, 1-10
3-10, 1-10
1-15, 3-15situations
Conduction
Conduction
Conduction
Switch position
UP
OFF
DOWNright front, avometer
terminal
4-15
4-6
6-15right rear, avometer
terminal
9-15
7-9
7-15Left rear, avometer
terminal
3-15
1-3
1-15situations
Conduction
Conduction
Conduction
Windshield/bodywork glass/wing mirror--Electric window control system
Phenomena
Electric window does not Work(all)(electric
door lock does Not work)
Electric window does not work(all) (electric
door lock is normal)
Automation system does Not work
Only one window can not Move
Electric window system Does not workimpossible positions
1. POWER fuse(center power distribution box)
2.
window shift main relay (center Distribution box)
3. wiring harness
1. ignition switch
2. left front door control Panel assembly
3. wiring harness
4. electric window generator
1. left front door control panel assembly
2. electric window generator (driver seat)
1. left front control panel assembly
2. electric window switch
3. electric window generator
4. wiring harness
1. left front door control panel assembly
2. wiring harnesswiring harness
-
-
-
-
319
-
320
319
320
319
320
320
-
319
-.
Inspect
1. Inspect left front door control panel assembly
[68000142]
Action switch, inspect the conduction among joint terminals.
Notes: Whether it works good or bad ,it can judged by
basic function. Becauce the conduction can not inspect
by ascending or descending driver’s electric window main
switch.
Electric window does not locked
Electric window locked
Malfunction phenomena table
If the conduction does not limit to regulations, replace electric window main switch.
 319 

Windshield/bodywork glass/wing mirror--Electric rearview mirror control system
Electric rearview mirror control system(option)
Inspect the vehicle
1. Inspect Electric retractable rearview mirror function
(a) Turn the ignition switch to ACC
(b) Inspect operating electric retractable rearview mirror function, when it at different positions.
(1) When retractable switch at steering position and left/right rearview mirror at steering position either,
press retractable switch, inspect left and right rearview mirrors whether they remove from steering
steering positionretractable
position
Electric
retract-
able
operation
Handle
operation
 329 
position to retraction position and stop at it.
(2) When retractable switch at steering position and left/
right rearview mirror at steering position either, if any one
of the rearmirrors can be pushed back by hand, then
press retractable switch to retractable position, inspect
left and right rearview mirrors whether they remove from
steering position to retraction position and stop at it.
(3) When retractable switch at retractable position and left/
right rearview mirror at steering position either, if any one
of the rearmirrors can be pushed back to steering posi-
tion by hand, then press retractable switch to retract-
able position , inspect whether rearview mirrors move to
restricted position only in steering position and stop at
it.
(4) When retractable switch at retractable position and left/
right rearview mirror at retractable position either, inspect
left and right rearview mirrors whether they remove from
retraction position to steering position and stop at it.
(5) When retractable switch at retractable position and left/
right rearview mirror at retractable position either, if any
one of the rearmirrors can be pushed back to steering
position by hand, then press retractable switch to steer-
ing position, inspect whether rearview mirrors move from
restricted position to steering position and stop at it.
steering positionretractable
position
Electric
retract-
able
operation
Handle
operation Electric
retract-
able
operationElectric
retract-
able
operation
Electric
retract-
able o
perationsteering positionretractable
position
steering positionretractable
position

Windshield/bodywork glass/wing mirror--Electric rearview mirror control system
(c) When operating left and right rearview mirrors, inspect whether ignition switch works when turn it to
OFF.
(1) When operating left and right rearview mirrors, turn ignition switch to OFF and inspect rearview
mirrors function whether they stop.
(2) Turn ignition switch to ACC again, inspect whether rearview mirrors work
Clues on: Turn ignition switch to OFF, if you press retractable switch and turn ignition
switch to ACC, then left and right rearview mirrors will move to opposite position.
(d) Inspect whether rearview mirrors work when restricted by others.
(1) When left and right rearview mirrors move to retractable position or steering position, restrict left
and right rearview mirrors manually, inspect retraction stops.
(2) Press retractable switch again, inspect whether it works.(at the opposite direction of stop position)
 330 

Panel/combination instrument--combination instrument
2. Inspect output signal of vehicle speed.
(1) When vehicle run at 10km/h, inspect voltage between ter-
minal10 and terminal A1 of combination instrument assembly.
Standards: the voltage pulsates repeatedly between
0V to 5V for thirteen times.
Notes: Inspect the ignition switch “on” connects the
joint
3. Inspect speed gauge
(1) Connect a test tachometer. then startup the engine.
Notes:
zTachometer terminals polarity connects oppositely will damage interior transistors and
LEDs.
zWhen move or disassemble tachometer. do not drop on the ground or knock the surface.
(2) Compare indicted value test tachometer and combination instrument tachometer.
Standard indicted value (rmp) permitted values (rpm)
700 630-770
1,000 (900-1,100)
2,000 (1,850-2,250)
3,000 2,850-3,150
4,000 (3,800-4,200)
5,000 4,750-5,250
6,000 (5,700-6,300)
7,000 6,650-7,350
DC 13.5V, 25°C
(1) Disassemble the joint of fuel meter
(2) Turn ignition switch to ON, inspect indictor position of fuel guage.
Indictor position: F
(3) Connect short terminal1 and terminal2 of wiring harness sides. Turn ignition switch to ON, inspect
indictor position of fuel guage.
Indictor position: F
5. Inspect low fuel level indictor 4. Inspect fuel gauge
The fuel gauge has the function of sensor detection (that is
failure treatment of oil level tachometer)that is when fuel gauge
indictor is at E position, if low oil level warning light doesn”t
light, first should judge whether there have open-loop trouble of
fuel sensor or wiring harness. When sensor fails, fuel indictor
should stop at current position. But if failing time is over 20
seconds, the indictor will return to E position quickly, the in-
strument will at wire break detection. If the normal situation of
detection panel is over 20 seconds, indicator will return to normal.
A1A20
 336 

Panel/combination instrument--combination instrument
(1) Disassemble fuel meter joints or break wire, when indictor is at E, fuel indictor does not light.
(2) Jumper a 300-330
resistor from the corner of terminal1 and termianl2, turn ignition switch to ON,
indictor is at E line, the indictor light lights.
6. Inspect generator water thermometer .
(1) Disassemble joint of generator water thermometer
(2) Turn ignition switch to ON, inspect indictor position of gen-
erator water thermometer.
Indictor position: COOL
(3) Earth 2 terminal of the wiring harness side joint to inspect
indictor position of generator water thermometer.
Indictor position: HOT
1 2 3
7. Inspect untied indictor light of driver seat belt.
(1) Turn ignition switch to ON, Inspect untied indictor light of driver seat belt lights.
(2) Tie the seat belt, inspect untied indictor light seat belt lights off.
(3) Disassemble the joint of safe belt button switch, earth the terminals of wiring harness
(4) Turn ignition switch to ON, inspect untied indictor light seat belt lights on.
8. Inspect low oil pressure indictor
(1) Disassemble the joint of oil pressure switch.
(2) Turn ignition switch to ON.
(3) Earth terminals of wiring harness sides, inspect low oil pressure indictor.
Low oil pressure indictor: light
9. Inspect oil pressure switch
(1) disassemble joints of oil pressure switch,
(2) Inspect the conduction of oil pressure switch terminals and earth.
Generator extinguishes: conduction
Generator works: not conduction
10. Inspect light warning buzzer
(a) Inspect the function of light warning buzzer
Clues on: light warning buzzer works together, only key
reminding buzzer works.
(1) Front combination light switch switches to ON, extract the
key, open driver seat door, inspect light warning buzzer.
Audio buzzer: Audio for 10 seconds in the night to cut
lamp power, in the day cut the lamp instantly.
(2) When buzzer works, do any one of the followings, inspect whether buzzer stop buzzing.
z zz z
zTurn front combination switch to OFF.
z zz z
zClose driver seat door.
z zz z
zInsert the key.
Buzzer Light switch
Key warning
switch
Pull out the key
Open driver door
 337 

Panel/combination instrument--combination instrument
(b) Inspect light warning buzzer function
(1) Disassemble combination instrument.
(2) Connect battery positive wire to terminal A5 and nega-
tive to terminal A1 and A2.
(3) Connect battery positive wire to terminal A18 and nega-
tive to terminalA17,inspect buzzer.
Audio buzzer: long buzzes
(4) When buzzer works, connect battery positive wire to ter-
minal A4,inspect whether buzzer stop working.
11. Inspect key buzzer
(a) Inspect when key buzzer and light warning buzzer works
together, only key buzzer works.
(1) Insert the key, when driver seat door opens, turn ignition
switch to OFF (LOCK or ACC). inspect key buzzer works
1HZ discontinuously.
(b) inspect key buzzer function
(1) Disassemble combination instrument.
(2) Connect battery positive wire to terminal A5 and nega-
tive to terminal A1 and A2.
(3) Connect battery negative wire to terminal A17 and B8,
inspect buzzer which should work discontinuously.
(4) When buzzer works, connect battery positive wire to ter-
minal A4,inspect whether buzzer stop working.
12. Inspect brake system indictor
(a) Inspect parking brake system indictor
Key warning
switch
Key switch
1G gear
Pull out the key
Open driver door
Buzzer
B8
B1
A1A20
(1) Disassemble the joint of parking brake switch, and earth terminals of wiring harness side joints.
(2) Turn ignition switch to ON, inspect brake system indictor light lights.
(b) Inspect brake oil level indicator light
(1) Disassemble the joint of brake oil level indicator light, connect terminal of wiring harness side
joints.
(2) Turn ignition switch to ON, inspect brake system indicator light lights.
 338 

Anti-stealing and door lock--Electric door lock control system
Anti-stealing and door lock
Electric door lock control system
Position of parts (only for reference)
Inspection on automobile
1. Basic inspection for electric door locker.
(a) Press middle control switch to locker closing side, and check the all doors should be locked; then
press middle control switch to locker opening side, and check all doors should be opened.
(b) Insert key in door locker and turn it anticlockwise, and check all doors should be locked; then turn the
key clockwise, and check all doors should be opened.
(c) Check the keeping protection function of the key.
Note: When checking the keeping protection function of the key, it is necessary to open elec-
tric window at the side of driver to prevent its function from losing and lock the key in
automobile.
(1) Insert key in ignition switch.
(2) Open the door, and press middle control switch on the door at the side of driver to locker closing
side, at this time, door locker could not close.
(3) Open the door, and press locker button on the door at the side of driver to locker closing side, at
this time, door locker could not close.
(4) After pressing locker button upwards for over two seconds, and locking driver door; when driver
door is closed and key is not used to lock, check whether all doors could open automatically.
 355 
Door control switch of electric
window main switch assembly
(Used for handle operation)
Door control switch of left front
door locker assembly
(Used for key operation)
Door control light switch
Left rear door locker
assembly
Right front door
locker assembly
Right rear door
locker assembly