ignition GEELY FC 2008 Repair Manual

Anti-stealing and door lock--Electric door lock control system
3. Check panel junction box assembly.
(a) Check 25A DOOR fuse.
(b) Check conformity relay.
(1) Disassemble F, G, H and I joint on instrument junction
box.
(2) Check the voltage and conduction of every terminal of
joint. (d) Check security function:
(1) When closing all doors, open the driver window to operate door control switch out of automobile.
(2) Take down the key, open driver door, then close the door and lock (not use key). In this situation
above, check that door could not open locker even if door control switch (handle operation) is
pressed to locker opening side out of automobile.
(3) Take down the key, close and use the key to lock driver door. In this situation above, check that
door could not open locker even if door control switch (handle operation) is pressed to locker
opening side out of automobile.
(4) Take down the key, close and use remote control key to lock driver door. In this situation above,
check that door could not open locker even if door control switch (handle operation) is pressed to
locker closing side out of automobile (only applicable for the automobile equipping with remote
control door locker control system).
Hint:
zIn following situation, check whether security has been canceled.
zIgnition switch is turned to ON.
zUse key operation to open the driver door locker.
zAfter door locker is pressed to opening side by hand, door control switch (handle
operation) is pressed to locker opening side.
zUse remote control locker control to open the door (only applicable for the automobile
equipping with remote control door locker control system).
2. Electric window main switch assembly
Operate door control switch by hand to check its conduction.
 356 
Position of switch Terminal connected by avometerRegulated situation
LOCK 5-1 or 5-3Conduction
UNLOCK8-1 or 8-3↑

Anti-stealing and door lock--Electronic anti-stealing system
Electronic anti-stealing system
Electronic anti-stealing system consists of anti-stealing controller, anti-stealing loop and transmitter. One
end of loop covers ignition locker core, the other end connects with anti-stealing controller, and the other end
of controller connects with engine ECU, at the same time, transmitter is assembled in key. Memory of
transmitter stores only mark (code) showing the legal identity of automobile owner, transmitter, anti-stealing
controller and electric injection ECU constitutes a multi-layer effective electronic anti-stealing system verified
by password.
If customer key loses, anti-stealing ECU is changed or engine ECU is changed, it is necessary to match
again in repairing station. When automobile leaves the factory, safety password is delivered directly to
owner for keeping with the type of secrecy. If it is necessary to make a new key, change anti-stealing
controller and make other operations, owner should bring the safety password with the automobile to repair
in repairing station. Repairing station should keep repairing (make new key, change anti-stealing controller
and so on) record for inquiring in future.
 361 

Electric sunroof (optional)--Sunroof system
Inspection for sunroof function
1. Inspection for sliding opening function.
(1) Turns ignition switch to ON, when spot contacting sunroof
switch keystroke 2, the sunroof will start automatic sliding
opening work, and it does not stop until it is at complete
opening state. If spot contacting it in running process, or
pressing keystroke 1 or 2 for long time, sunroof glass will
stop running immediately.
(2) Turns ignition switch to ON, when pressing keystroke 2 for
Sunroof system
Specification for sunroof function
1. Operation category
Spot contact: press the keystroke one time, then release immediately (the time is less than 0.3 seconds).
Long press: press the key stroke for long time (the time is more than 0.3).
2. Specification for function.
Anti-clamping function: spot contact the keystroke to make the sunroof could face 10 Kg resistance in the
process of closing from any position, at this time, electric motor turns oppositely, and the sunroof returns
turn-up or opening state.
Automatic closing function: when the key is pulled out from ignition locker, at this time, the sunroof is not
at closing state, it will close automatically in three seconds.
long time, the sunroof will start automatic sliding opening work, and it does not stop until it is at
complete opening state. If releasing keystroke 2 in running process, the sunroof glass will stop running
immediately.
2. Inspection for sliding closing function.
(1) Turns ignition switch to ON, if the sunroof is at opening state, when spot contacting sunroof switch
keystroke 1, the sunroof will automatically slide to closing state. If spot contacting it or pressing
keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at opening state, when pressing sunroof switch keystroke
1 for long time, the sunroof will automatically slide to closing state. If releasing keystroke 1 in running
process, sunroof glass will stop running immediately.
3. Inspection for turn-up opening function
(1) Turns ignition switch to ON, if the sunroof is at closing state, when spot contacting sunroof switch
keystroke 1, the sunroof will automatically move to turn-up opening state. If spot contacting it again or
pressing keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at closing state, when pressing sunroof switch keystroke
1 for long time, the sunroof will automatically slide to turn-up opening state. If releasing keystroke 1 in
running process, sunroof glass will stop running immediately.
4. Inspection for turn-up closing function
(1) Turns ignition switch to ON, if the sunroof is at turn-up opening state, when spot contacting sunroof
switch keystroke 2, the sunroof will automatically move to closing state. If spot contacting it again or
pressing keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at turn-up opening state, when pressing sunroof switch
keystroke 2 for long time, the sunroof will automatically slide to closing state. If releasing keystroke 2
in running process, sunroof glass will stop running immediately.
 364 
Front
Rear

Electric sunroof (optional)--Sunroof system
Inspection for sunroof switch
(a) Check the function of switch. Disassemble front top light,
and disassemble the joint of front top light, then check the
joint at the side of switch liking that shown in figure.
Malfunction phenomenon table Position of parts
Malfunction phenomenon
Sunroof system does not work
Sunroof system works abnormallyPossible malfunction part
1. Ignition switch.
2. Control switch of sunroof.
3. 25A, 15# fuse.
4. Wiring harness
1. Control switch of sunroof.
2. Wiring harnessReference page
-
-
-
-
-
-
 365 
Terminal connected by avometer
2-4
2-5ConditionSpot contact or press
keystroke 2 for long time
Spot contact or press
keystroke 1 for long time
Regulated situa-
tion
Conduction
Conductiion
Shell body of sunroof
Motor of sunroof
Switch of sunroof

Engine cover/automobile door--Front automobile door
17. Assemble left front door glass lift assembly [67000122]
(a) Use six bolts to assemble left front door glass lift.
Torque: 8.0 N
⋅ ⋅⋅ ⋅
⋅m
(b) Assemble electric window lift and door glass.
(c) Connect electric window switch to wiring harness and turn ignition switch to ON.
(d) Operate UP and DOWN several times by hand repeatedly.
(e) Check whether the AUTO UP→AUTO DOWN of automatic operation is normal.
Hint:
zWhen it is set up again, anti-clamping protection function does not work.
zAfter implementing AUTO UP operation to close window completely, if automobile window
could not be operated downwards, it is necessary to set up the lift again.
(f) Check the function of electric window.
 371  18. Check the function of electric window
19. Assemble repairing hole cover of left front door
Hint:
zWhen assembling repairing hole cover, pull out con-
necting rod and joint from repairing hole cover.
zAfter assembling repairing hole cover, connecting rod
and joint could not be bent or concaved.
zAfter assembling repairing hole cover, it is necessary
to confirm the affixing situation of adhesive tape.

Automobile control system--Ignition switch and anti-versa lock key warning switch
Phenomenon
Ignition switch could not insert on any
positionPossible malfunction part
1. Ignition switch
2. Circuit of power supplyReference page
394
-
Automobile control system
Ignition switch and anti-versa lock key warning switch
Malfunction phenomenon table
Inspection
1. Check the ignition switch.
Check the conduction of ignition switch joint and terminal
If the conduction does not accord with the regulation, change
the switch.
2. Check the anti-versa lock key warning switch.
If the conduction does not accord with the regulation, change
the switch.
 394 
Position of switch Terminal connected by avometerRegulated situation
LOCK - Not conduction
ACC 1-3 Conduction
ON 1-2-3, 5-6Conduction
START 1-2, 4-5-6Conduction
Position of switch Terminal connected by avometerRegulated situation
OFF (key does not insert)- Not conduction
ON (key inserts)1-2 Conduction

Ignition switch/starting/chargingElectrical schematic diagram--Ignition switch/starting/charging 395