Light GEELY MK 2008 Repair Manual

No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
255-128 4. Eliminate fault code either by diagnosis instrument or manually. Manual operation method, specific
procedure: use engine data K-line (namely 9 # terminal of diagnostic interface) earth twice, earthing time is more
than 2. 5 s at each time.
Fault code tableFaulty part
No fault
Electronic control unit (unit) fault
Knocking control zero test
Knocking sensor
Storage battery voltage
Intake pressure sensor
Throttle position sensor
Idle speed control valve
Coolant temperature sensor
Intake temperature sensor
Engine maximum speed overrun
Fuel injector 1
Fuel injector 2
Fuel injector 3
Fuel injector 4
Fan relay
Oxygen sensor
Air fuel ratio control correction coefficient
? self-learning value 1
? self-learning value 2
? self-learning value 3
Fault caution light
Canister control valve
Air conditioner condenser temperature sensor
Phase sensorFault code
11
34
1
15
38
16
14
61
19
18
33
22
23
24
21
42
17
31
35
36
37
45
25
13
43Fault lamp
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ONFault type
-
2
-
2
2
1
1
1
1
1
2
1
1
1
1
1
1
2
2
2
2
1
1
1
1
Fault type: 1-open circuit 2-signal overrun
No. 18 to 21 in the table refers to air fuel ratio correction coefficient,?=actual air quantity/air need for
combustion, "? self-learning value" is also called learning air fuel ratio control value.Engine EFI System-
Engine EFI System

III. Troubleshooting:1.Whether power supply is normal or not.
2. Increase mobile phone output volume.
3. Confirm whether mobile phone interface line is correct, (replace
with new mobile phone interface line).
4. When mobile phone works, confirm whether there is relay
closing sound in hands-free telephone box.
5. If there is relay closing sound, check whether anything is wrong
with socket drop-out line.
Adjust mobile phone output volume.
Check receiving signal of mobile phone. No. Symptom Possible cause
1
2
3No voice can be heard from
hands-free telephone
Loudspeaker sound is light
Connection is interruptedOn Board Vehicle Telephone-On-board Vehicle Telephone5-130

III. Fault diagnosis 1. During detection, if there is no sound or display screen does not illuminate, please detect whether polarity
of power supply is connected in a wrong way, whether power cord is connected, whether supply voltage 9V,
whether display joint is inserted properly.
2. If clobber "0.0" or constant ringing occurs, please exit reverse gear, engage reverse gear again. If the
above symptom still exists, it may be deemed that principal machine is damaged, and should be replaced
completely.
3. If certain value is displayed, while there is no evident barrier at right ahead of probe. Prominence on or rear
might be detected (such as license plate, bumper bar etc). please check whether direction axis of the probe is
correct, horizontal axis of the probe should slightly upwarp.
4. When accelerating, the installed display shows irregular disordered frame, circuit interference might occur,
check earth wire of reversing radar.IV. Installation of reversing radar 1. Reversing radar system consists of reversing radar principal machine, reversing radar display screen, wiring
harness, buckle and reversing radar probe etc.Rear Parking Radar System-
Rear Parking Radar System5-132About 500 mm
About 265 mmRear parking radarsensor
Clip
Push Rear bumper bar

Centralized Controller System-
Function Inspectior5-133Chapter 12 Centralized Controller SystemSection 1 Function InspectiorI. Glass frame riser: 1. Glass frame riser may be operated to move within 60s after ignition switch is turned on or off; 60s after
ignition switch is turned off, glass frame riser cannot be operated to move;
2. Manual rise: press corresponding glass frame riser switch rise key, corresponding glass frame riser motor
works, glass frame rises, release rise key, it stops.
3. Manual fall: press corresponding glass frame riser switch fall key (hold time 300ms), corresponding glass
frame riser motor works, glass frame falls, release fall key, it stops.
4. Automatic fall: press corresponding glass frame riser switch fall key (hold time < 300 ms), corresponding
glass frame riser motor works, glass frame falls down to end; or fall down until rise key or fall key is pressed again.
Note:
During automatic fall of glass frame, if corresponding glass frame riser switch fall key is pressed down for more
than 300 ms, glass frame riser is changed to manual fall mode; if corresponding glass frame riser switch rise key
is pressed down for more than 300ms, glass frame riser stops work.
5. Remote window closing:
In case of remote protection, if a key is pressed down for more than 1s, perform glass frame riser automatic
rise action, left front, right front, left rear, right rear in turn.II. Central lock: 1. In case protection is deactivated, use a key to open left front door switch or press internal unlock switch to
open four door fasteners; close left front door switch, close four door fasteners.
2. Remote unlock /lock:
(1) Ignition switch opening
a. Press remote control unlock key to open four door fasteners;
b. Press remote lock key to close four door fasteners;
(2) Turn off ignition switch
a. Press remote unlock key to open four front door fasteners, at the same time turn light flashes once.
b. Press remote lock key to close four door fasteners, at the same time turn light flashes twice.
(3) When door is opened, press remote fastener, turn light will flash for three times, at the same time electric
horn beeps for three times.
(4) If the system is triggered in anti-theft condition, when remote unlock system exits protection state,
directional turn signal will flash for four times, at the same time, electric horn beeps for four times.
3. Automatic lock
When vehicle speed exceeds 30km/h, three doors will be closed.
4. Door lock priority
Central door lock should not act simultaneously with glass frame riser; when they conflict with each other,
central door lock acts with priority, while glass frame riser stops; after central door lock action is finished, glass
frame riser continue its work in previous condition.III. Front womdscreem wiper: After spray water signal is finished, the wiper acts twice.

IV. Post-defrost: 1. When engine speed exceeds 700rpm (ignition switch is turned on), defrost work is permitted.
2. Turn on defrost switch, perform defrost work for 12 minutes, if defrost switch is pressed down again during
defrost work, defrost work will stop.
3. During defrost, turn off ignition switch, cancel this defrost.V. Light control: 1. Headlight:
(1) After press remote lock key to close four doors, if remote lock key is pressed down again twice in
succession within in 2s, dipped headlight will extend lighting for 1 minute; if remote unlock key is
pressed down within 60s, dipped headlight control output will be turned off.
(2) During output of 60s low level, if ignition switch is turned on, low level output will stop.
2. Ceiling lamp:
(1) When any of the doors is opened, ceiling lamp illuminates; if door is not closed, ceiling lamp will be
turned off after 10 minutes of delay.
(2) For closing of all doors, ceiling lamp will go out after time delay of 30s;
(3) In case all doors are closed,and ceiling lamp illuminates,ignition switch is turned on,ceiling lamp goes
out.
(4) For remote unlock, ceiling lamp illuminates; in case all doors are closed and ceiling lamp illuminates,
remote lock ceiling lamp goes out.VI. Remote anti-theft 1. Protected state: press lock key on remote controller, while closing four doors, anti-theft indicator lamp will
flashes slowly, indicating that the system enters protected state, when the system is triggered, turn light of the
vehicle will flash, warning horn gives out alarm.
2. Cancel protection: press unlock key on remote controller, while opening left front door, anti-theft indicator
lamp flashes rapidly, if at least one of ignition switch, door is opened within 30 s, anti-theft indicator lamp will
go out; otherwise it will enter secondary anti-theft state.
3. Two stage type protection cancellation: while the system is in triggered state, press any key on the remote
controller, alarm sound will stop, however, the system is still in protected state, and car door is still locked; if the
system continues to receive invasion signal, alarm will ring again after brief stop. To cancel protection completely,
cancel alarm for the first time, then press unlock key once immediately;
4. Secondary anti-theft: after protection is cancelled, if any of ignition switch, door is not opened within 30s,
the system will restore alert status automatically, and lock the car door.
Distribution of centralized controller connector terminals:
Connector on wiring harness, as shown in the figure below (view from outgoing terminal):Centralized Controller System-
Function Inspectior5-134Centralized
controller

Centralized Controller System-Function Inspectior5-135Terminal No.
A1
3
4
5
6
7
8
9
10
11
14
15
19
20
21
22
24
26
27
28
29
30
31
32
33
34
35
36RY
YR
BBL
BR
BL
GR
WR
WB
BR
WG
BW
Gr
VY
BG
WG
BLW
BR
BY
BG
R
O
GR
WG
BLB
BLR
BLPower supply (+)
Speed sensor signal
Engine speed signal
IG2
Spray water signal wiper switch 7#Wiper intermittent position signal (+)
Right front door lamp switch
Left front door lamp switch
Hazard lamp switch
GND
Right rear door lamp switch
Left rear door lamp switch
Rear right glass regulator switch (down)
Rear right glass regulator switch (up)
Turn light switch (right turn)
Turn light switch (left turn)
Defrost switch
Left front door fastener unlocked signal
Left front door fastener locked signal
Anti-theft indicator lamp
Rear left glass regulator switch (down)
Rear left glass regulator switch (up)
Front right glass regulator switch (down)
Front right glass regulator switch (up)
Front left glass regulator switch (down)
Front left glass regulator switch (up)
GND
Antenna Definition of centralized controller terminals:Conductor color Terminal definitionConnector A
Connector B Connector C

Terminal No.
B1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25G
G
RY
Br
GB
GW
BLW
Br
RB
RB
YB
YB
RBL
RBL
GBL
R
RW
RW
BR
WR
BL
W
WB
BLB
R
BLB
WB
BLY
WY
RBHazard lamp power supply
Hazard lamp power supply
Dome lamp
Wiper motor (INT)
GND
GND
Right turn light and its indicator lamp
Left turn light and its indicator lamp
IG2
Wiper switch 3#Head light relay 85 #Head light relay 85 #Rear air window defrost and indicator lamp
Rear air window defrost and indicator lamp
Rear air window defrost power supply
Rear air window defrost power supply
GND
Horn relay 85 #Electric glass frame power supply
GND
GND
Fastener power supply
Right front, right rear, left rear fastener
Right front, right rear, left rear fastener
Left actuator
Front left glass regulator
Front left glass regulator
GND
Front right glass regulator
Front right glass regulator
Glass power supply
Rear left glass regulator
Rear left glass regulator
GND
Rear Right glass regulator
Rear Right glass regulator
Left actuatorConductor color Terminal definitionCReplacement ( 1 ) Remove dashboard subassembly (refer to trim)
( 2 ) Remove two bolts5-136Centralized Controller System-
Function Inspectior

Chapter 4 Rear Seat BeltI.Component ViewInterior & Exterior Trim and Accessory -Rear Seat Belt6-940¡«60N.
m
RL/LH safety belt
assy.
Rear left C-pillar
upper trim Rear left C-pillar
lower trim
Rear left buckle assy.
Rear left backrest assembly Rear right buckle &
waistband Assy.
Rear cushion assy.Rear right C-pillar
lower trim Rear right C-pillar
upper trimRR/RH safety belt assy.
Rear shelf trim
High mounted
stop light
assemblyRear right backrest
assembly

Interior & Exterior Trim and Accessory -Rear Seat Belt6-10II. Rear seat belt removal1. Remove the rear cushion assembly;
2. Remove the rear backrest assembly;
3. Remove left (right) side quarter upper trim;
4. Remove the high mounted stop light;
5. Remove the rear shelf trim;
6. Remove the rear seat belt assembly;
a. Remove bolts under the quarter lower trim connecting the left and right rear side;
b. Remove bolts for the retractor and take down the rear seat belt assembly;
7. Remove bolts on the floor and disassemble the right rear seat belt buckle assembly and the waistband assembly;
8. Remove bolts on the floor and take down the left and rear buckle assembly.III. Installing rear seat belt1. Install the left and rear buckle assembly;
As per the drawing, bolt the left and rear buckle assembly. on the
floor. Torque: 40~60N.m
2. Install the right rear seat belt buckle and the waistband assembly;
Tips: same as way of the left.
3. Install the rear seat belt assembly;
Attention: Do not break down the retractor.
a.Inspection contents before outer seat belt instalation:When ELR
lock,check the gradient of ELR. Check and make sure the seat belt
can not be locked from any aspect within 15°.When you move the
belt ring device beyond 45° slowly,the seat belt should be locked.
b. Install the rear seat belt assembly using bolts (part of
retractor) ;
Torque: 40~60N.m
c. Install the rear seat belt assembly using bolts(part of anchor).
Torque: 40~60N.m
4. Inspect the properties of seat belt assembly;
5. Install the rear seat and trim.Floor projectionFrontFront markLockUnlockIV. Precaution for Usage and Disposal of Used Safty Belt The details are the same as front safty belt.

Chapter 7 Rear Window Glass (with Defrosting Heater Wire)II. Removal and Replacement of Rear Windscreen Glasses Tip:
Installation is basically the reverse of removal and different operation(s) in the process of installation, if any,
will be pointed out specifically.I. Component ViewRear right roof handleRoof trim
Rear windscreen stopperRear windscreen weather strip
Rear right C-pillar trim
Windscreen glass
weather stripHight mounted brake light assembly
Rear shelf trim Rear left C-pillar trim rear windscreen glass Rear left roof handleInterior & Exterior Trim and Accessory -Rear Window Glass (with Defrosting Heater Wire)6-20