service interval reset HONDA FIT 2016 3.G Quick Guide

112 || 113
MAINTENANCE
MAINTENANCE
Safety Precautions
Some of the most important safety precautions are listed below; however, we cannot  warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.
Maintenance Safety
• 
To reduce the possibility of ire or explosion, keep cigarettes, sparks, and lames 
away from the battery and all fuel-related parts.
•  Never leave rags, towels, or other lammable objects under the hood.
•  To clean parts, use a commercially available degreaser or parts cleaner, not  gasoline.
•  Wear eye protection and protective clothing when working with the battery or 
compressed air.
•  Do not run the engine in conined spaces where carbon monoxide gas can 
accumulate.
Vehicle Safety
•  The vehicle must be stationary, and parked on level ground with the parking 
brake set and the engine off.
•  Be aware that hot parts can burn you. •  Be aware that moving parts can injure you.
Improperly maintaining this vehicle or failing to correct a problem before  driving can cause a crash in which you can be seriously hurt or killed.  Always follow the inspection and maintenance recommendations according to the schedules in this guide.
WARNING
Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed. Always follow the procedures and precautions in this guide.
WARNING
Learn about basic maintenance that you can perform on the vehicle yourself, as well  as information about how to best maintain the vehicle.
MAINTENANCEMaintenance Minder™
When maintenance is due, the Maintenance Minder indicator comes on and a
message appears on the display every time you turn the vehicle on. Press the select/reset knob to change displays. See the service code table on page 114 to check which items need maintenance 
based on the main and sub items shown in the display.
Maintenance Minder indicatorMain items
Sub items
Maintenance Minder display
•  Independent of the Maintenance Minder information, replace the brake luid every  3 years.
•  Inspect idle speed every 160,000 miles (256,000 km).
•  Adjust the valves during services A, B, 1, 2, or 3 if they are noisy.
U.S. models
Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individuals using parts that
are certied to EPA standards. According to state and federal regulations, failure to perform maintenance on the
maintenance main items marked with # will not void your emissions warranties.
However, all maintenance services should be performed in accordance with the 
intervals indicated by the multi-information display.

116 || 117
MAINTENANCE
MAINTENANCE
Recommended Engine Oil
• Honda Genuine Motor Oil
•  Premium-grade 0W-20 detergent oil with an API Certication Seal on the
container
This seal indicates the oil is energy conserving and
that it meets the American Petroleum Institute’s  latest requirements. Use Honda Genuine Motor Oil or another commercial engine oil of suitable viscosity for the ambient temperature as shown.
You may also use synthetic motor oil if it is labeled with the API Certiication Seal  and is of the specied viscosity grade.
Engine Oil
Park the vehicle on level ground, and wait approximately three minutes after turning the engine off before you check the oil.
Checking the Oil
1. Remove the dipstick (orange).
2. Wipe the dipstick with a clean cloth or paper towel.
3. Insert the dipstick back all the way into its hole.
4. Remove the dipstick again, and check the level. It should be between the upper and lower marks. 
Add oil if necessary.
Ambient temperature
Upper mark Lower mark
Adding Oil
1. Unscrew and remove the engine oil ll cap.
2. Add oil slowly.
3. Reinstall the engine oil ll cap, and tighten it securely.
4. Wait for three minutes and recheck the engine oil dipstick.
Resetting the Engine Oil Life
If you change or replace the vehicle’s engine oil yourself, you must reset the  engine oil life. 1. Press the select/reset knob until the oil life  screen is displayed.
2. Press and hold the knob for 10 seconds, or until the maintenance codes and oil life blink.
3. Press and hold the knob for 5 seconds, or until the maintenance codes disappear and the engine oil life display returns to 100%.
Do not ill the engine oil above the upper mark. Overilling the engine oil can result  in leaks and engine damage.
NOTICE
Failure to reset the engine oil life after a maintenance service results in the
system showing incorrect maintenance intervals, which can lead to serious mechanical problems.
NOTICE
Engine oil ill cap