ecm connector HONDA INTEGRA 1994 4.G Owner's Manual

PGM-FI System
Manifold Absolute Pressure
lFrom page 11-53)
{MAPI Sensor (cont'd)
(From paqe 1 1-53)
NO
M6asure voltage between D17{+) terminal and 021 (-}terminal.
ls there approx. 3 V?
Substituto 6 known{ood ECM.nd rach.ck. It symptom/indica-tion gooa away, Eplaco tho orlgi-nrl €CM.
Turn the ignition switch OFF.
Connect the test harness "D"
connector to the ECM only. not tothe main wire harness lsee page11-37).
Turn the ignition switch ON.
Measure voltage botwson Dl7(+) terminal and D21 {-}terminal.
R.p.lr opon or ahort in WHT|rELwi?o botw.on ECM {O17) and thoMAP senso..ls there approx. 5 V?
Substitute a known{ood ECMand rochsck. It prdcribed voltrgob now availablo, rophce trie origi-nal ECM.
approx. 3 v?
-D17 til D21 (-l
ooooooooooooo I oooooooo l l5oiE€tdl ooooooo
o oooo oooooooo ! ooooooooooooooooooo
11-54
'.---.-'

PGM-FI System
TDC/CKP/CYP Sensor
_f'=l_ fi_l The Malfunction Indicator Lamp (MlL) indicates Diagnostic Trouble Code (DTC) 4: A problem int:- the Crankshaft Position (CKP) Sensor circuir.
l'6]- ftl - The Malfunction Indicator Lamp (MlL) indicates Diagnostic Trouble Code (DTC) 8: A problem in-i- the ToD Dead Center ITDC) Sensor circuit.
-flG]l- ft-] The Malfunction Indicator Lamp (MlL) indicates Diagnostic Trouble Code (DTC) 9: A problem in- , - the Cvlinder Position ICYP) Sensor circuit.
The CKP Sensor determines timing tor fuel injection and ignition of each cylinder and also detects engine speed. TheTDC Sensor determines ignition timing at start-up (cranking) and when crank angle is abnormal. The CYP Sensor detects
the position of No. 1 cylinder tor sequential fudl injection to each cylinder.
- \.--r-l - -__l_-
tPJ:;LlJ:lEl--;l ?,:
- Tho MIL hos beon roponod on.- With rho SCS short connoctorconneclod lsso pago I l-341,code 4, 8 and/or 9 ar6 in-dicated.
Do the ECM Reset procedure (seepage 11-35).
Intohittent failuro, syst€m is OKat thia tima {t6st drivo may benoceaSaayr.Chock for poo. connections orlooss wires at C222 (located atright shock towerl, C110(TOC/CKP/CYP Sonsorl and ECM.
ls the MiL on and does it in-dicate code 4, 8 and/or 9?
Turn the ignition switch OFF.
Disconnect the 8P connector fromthe TDC/CKP/CYP sensor.
{To page 1 1-57)
11-56

ECT SENSOR
GRN/BLU {-}
Turn the ignition switch ON.
Measure voltage betweon RED/WHT and body ground.
Measure voltage between RED/WHT {+}terminal and GRN/8LU(- ) terminal.ls there approx. 5 V?
ls there approx. 5 V?Ropai. opon in GRN/BLU wiro botwoon ECM(D221 and tho ECT36n3('r.Turn the ignition switch OFF.
Sub3tituto a known-good €CMand rochock. lf 3ymptom/indica-tion go6s away, roplaco the odgi-nal ECM.
Oisconnect the 22P connectortrom the Transmission ControlModule (TCM).
Turn the ignition switch ON.
ls there approx. 5 V7
Turn the ignition switch OFF andreconnect the connector to theTCM.
Connect the test harn€ss "D"
connector to the ECM only. not tothe main wire harness {see page11-37).
Turn the ignition switch ON.
Measure voltage between D13(+) terminal and D22 (-l ter-mlnal.
Repair opoa or shon inREO/WHT wiro botwoen ECMlDl3l and th6 ECT sonsor.R6pair shon in REO/WHT YYi..b6tw66n ECM {D131and TCM.
ls the.e approx. 5 V?
Substiluto a known-good ECMand rochock. ll lymptom/indica-tion goea 6wsy, replaco tho o.igi-n6l ECM,
A/T only
I
_i
11-59

.:-\.-----ll@l--l t l- The Malfunction Indicator Lamp (MtL) indicatee Diagnostic Trouble Cod€ (DTC) 7: A problcm inrhe Thronle Position (TPl Sonsor circuit.The TP Sensor is a potsntiometer, lt is connected to the throttle valve shaft. A8 the throttlo position chan96, the throttlopositaon sensor varies the voltage signal to the ECM.
BBUSHHOLDER
PGM-FI System
Throttle Position (TPl Sensor
OUTPUT VOLTAGE IV)
BNUSH
RESISTOF
IXNOTTII
TERMIIIAL;0rr- of€ no
THNOTTIE
YEL/aLU l+l TP SEITSOR
I
a
t
t
Io.|o
RED/BLK {-I
cnn/BLu I - l
)ran1 )ril-Y- -?..
- Th. MIL h.. baln rlport d on.- With th. SCS thort conn.ciolconn.c-ted (rco pngc 11-341.codo 7 i. indlc.t d.
Do the ECM Reset hocedure (se€page l 'l-35).
l. ..mrtt nt fClur., lyrt m la OX.t thb dm. ll.at drlv. rn.y brncoaataryl.Chack lor poo? connactlo|ra otloora wlr.r !t C223 lloc.t d !tdgtn drod( tow..t, Cl15 ITP ...t-rorl, C419 (TCMI .nd ECM.
ls the MIL on and do€s itindicats codo 7?
Turn th€ ignition switch OFF.
Disconnect tho 3P connector lromth€ TP sensor.
Turn the ignition switch ON.
Meosu.o voltage betwoon YEL/BLU (i ) terminal and GRN/BLUI -, torminal.
Measurs voltagG betw66n YEUBLU (+l terminal and bodygiound.ls there approx. 5 V?
(To page 1 1-611
11-60
(To page 1 1-6'l )
,,,----

(From1 1-60){From
A/T only
Turn the ignition switch OFF.
Connect the test harness betweenthe ECM and connectors (seepage 11-37l-.
Turn the ignilion switch ON.
Measure voltage between D1 1 {+ )terminal and 022 (- I terminal.
Turn the ignition switch OFF.
ls voltage approx. O.5 V at lullclose throtlle. and approx. 4 vat full open throttle?NOTE: There should be asmooth transition as the throt-tle is depressed.
Disconnect the 22P connectorfrom the Transmission ControlModule (TCM).
lurn the ignition switch ON.
Substitute a known-good ECMand roch6ck. ll symptom/indica-tion 9063 away, roplaco th6 origi-nal ECM.- Replaco tho TPaonsoa,- Repai. opon or ahonin RED/BLK wir. b€-twoon ECM lDl1l,TCM 6nd TP sonsor.
ls voltage approx. 0.5 V ar fullclose throttle, and approx. 4 Vat tull open throttle?NOTE: There should be asmooth transition as the throt'tle is deprossod.
page 1 1-60)
Repsir op.n in GRN/8LU wii6 botwoon ECMlD22l snd tho TPaenaot.
ls there approx. 5 V ?
Turn the ignition switch OFF.
Connect the test hamess betweenthe ECM and connector {see page11-37).
Turn the ignition switch ON.
Measure voltage between D2O{+) terminsl and D22 {-}termtnal,
Ropoi. open in YEL/BLUwire bgtween ECM{D20} and rho TP30naot.
ls there approx. 5 V 7
-ReDai. ahort in YEL/BLU wiroborwoon ECM (D2Ol and tho TPson30t.-Sub3tituto a known-good ECM6nd rochock. It prcacribod vol-t6go is now availablo, roplacoth6 original ECM.
Fr. o.5 v n tua .b drdn ?
11-61

PGM-FI System
Intake Air Temperature (lAT) Sensor
----:-- z ---L /-h6l- I t0 l- The Malfunction Indicator Lamp (MlL) indicstes Diagnostic Trouble Cod6 (DTC) 1O: A problem in/ | / - the Intake Air TemDerature (lAT) Sensor circuit,
The IAT Sensor is a temperature dependant resistor (the.mistor). The resistanc€ of the thermistor d6creases 8s the
intake air temDeratura incroases as shown below.
)1611:till/ ---l- z ---i-\
THERMISTOR
RED/YELI + )
RESTSTAXCE tmt
Bl8Bl onglnc:
-a a2 aa roa .t7a 212 a t |l-20 o 20 rto ao I t6 rro t.cl
I TAKE AIR TEiiIPTFATURE
818C1 .nglnc:IAT SEI{SOR
11-62
wi.a sido
- Th! *llL hs b!!n Egortad on.- \|
rdr dra SCS rhon connrcto.conn.ct.d lt . psg. 1l-341.cod. 10 l. hdlclt.d.
Do the ECM Resot kocoduro {se€pago 11-35).
Turn the ignition switch ON.Into.n{tlont failuro. rys-r.m ir OK .t thi. iim.(toat drlvc m6y b6arooa!!1ryt.Ched( tor poor clnncc-lioiE or loote wlrar 6tC223 lloc.tod rightlhock toworl, C12O(lAT renrcrl and ECM.
ls the MIL on and doos itindicate code 10 ?
Turn the ignition swiich OFF.
Oisconnoct tho 2P connector fromthe IAT sensor.
Meosu.e resistonc€ between the2 torminals on the IAT aengor.
ls thero 0.4-4.0 k0?Rlobco tho IAT aonsor.
(To pago 1'l-63)

Disconnect the "B" connectorfrom the ECM only, not the mainwile hatness.
Turn the ignition switch ON.
Block tho right front who€l andslowlv rotate l6ft front wheel andm€asure voltage between 8'l Ol+) terminal and A26 (-)
terminal.- Roo.ir lhort in ORt{wire belween ECM18101 tnd rhs VSSor cruia6 controlunit.- ncp.i. op€n in ORI{wira botwoan ECM(8101 and the vSS.- It wir. i! OK, totttho vSS. lsoc aec-tion 231
Doos voltage pulso O V and'to v?
SubrtituL . known-good ECil lndEch.ck. fi lynptom/ndcltbn gp..
rw!y, .rpleco lh. original ECM.
(From page 1 1-68)
1 1-69

(From pog6 1 1-7Ol
Meaauro voltage betweon GBN/RED ierminal and body ground.
Boplir opon 01lhort in GR /REDwir. batworn ECM (DlOl and tho
3P connoctor.1l wir. i! OK, .ubrtituta. known-good ECM .nd rochock.
13 the.e approx, 5 V?
Turn tho ignition switch OFF.
connect tho loat hamasa botweontho ECM and connectors (soa
pag€ 11-37),
wire side
BLK {_I
GR /NED I-I
BLKIEL { + }
(To page 11-72)
11-71

PGM-FI System
A/T Fl Signal A/B (A/T only)
\[l0l- The Maltunction Indicaror Lamp (MlL) indicates Diagnostic Trouble Code (DTC) 30: A problem In-L= the A/T Fl Signat A circuit between Transmission Control Module (TCMI and ECM.
tItil- The Malfuncrion Indicaror Lamp {MlL) indicates Diagnostic Trouble Code {DTCI 31: A problem In-Li!- the A/T Fl Signal B circuit between Transmission Controt Module (TCM) and ECM.
\.__r_/ \.__r_/-l 30 l- o'-l 3t l------ /----\
84'
+ulty? Continuity?
r: code 31 1A/T Fl signal Bl
11-76
Wlth tho SCS ahon connocrolconi|ocd {!o. p.g. 'l 1 -341, codo3O and/or 31 ars indicltod.
Oo ths ECM Resot Proceduro {seepag€ 'l 1-35).
Test drive necessary.Drive the car lor several miles sothat the transmission uDshifts anddownshilts several times.
Intormittant tsilu.o, sy3tem iB OKat thir tima,Chack lor poor connactions otl.ro!€ wiror at C419 (TCM] andECM.
Does the MIL indicare code30 and/or 31?
Turn the ignition switch OFF.
Connect the test harness to th€main harness only, not to the ECM(see p8go l'l-37).
Disconnect the 22P connectorfrom the TCM.
Check lor continuity between B3andlor 84' terminal and bodygrouno.
Ropair lhon in GRN/8LU or GRY'wiro b6twoon ECM (83 or 84'land tho TCM.
(To page 11-77)

(From page 1 'l-76)
Check for continuity on GRN/BLUor GRY'wire between 83 or 84'and 22P connector of the TCM.
Ropair open in GRN/BLU or GRY'wiro botwoon ECM lB3 or B4'land the TCM,
Substituts a known-good ECMand rochock. ll symptom/indica-tion goos 6way, roplaca tho origi-nal ECM.
11-77