HYUNDAI PALISADE 2023 Owners Manual

Convenience Features5-102
B0179KO01
Hight Beam Assist will automatically
switch between high beam and low
beam depending on the detected
brightness from the lamps of oncoming
vehicles or vehicles in front.
Detecting sensor
B0179KO02
M: front view camera
The front view camera is used as a
detecting sensor to detect ambient light
and brightness while driving.
Refer to the picture above for the
detailed location of the detecting sensor.
NOTICE

[ Always keep the front view camera in
good condition to maintain optimal
performance of High Beam Assist.

[ )RUPRUHGHWDLOVRQWKHSUHFDXWLRQV
of the front view camera, refer to

U)RUZDUG&ROOLVLRQ$YRLGDQFH$VVLVW
)&$
VVHFWLRQLQFKDSWHU
High Beam Assist Settings
B0179EU03
With the ignition switch or the Engine
Start/Stop button in the ON position,
VHOHFW
S/LJKWV

05
5-103
High Beam Assist Operation
Display and control

[After selecting ‘High Beam Assist’
in the Settings menu, High Beam
Assist will operate by following the
procedure below.

- Place the headlight switch in
the AUTO position and push
the headlight lever towards the
instrument cluster. The High Beam
Assist (
) indicator light will
illuminate on the cluster and High
Beam Assist will be enabled.

- When High Beam Assist is enabled,
high beam will turn on when vehicle
speed is above 25 mph (40 km/h).
When vehicle speed is below 15
mph (25 km/h), high beam will turn
off.

- The High Beam (
) indicator light
will illuminate on the cluster when
high beam is on.

[ When High Beam Assist is operating,
if the headlight lever or switch is used,
High Beam Assist operates as follow:

- If the headlight lever is pulled
towards you when the high beam
is off, the high beam will turn on
without High Beam Assist canceled.
When you let go of the headlight
lever, the lever will move to the
middle and the high beam will turn
off.

- If the headlight lever is pulled
towards you when the high beam is
on by High Beam Assist, low beam
will be on and High Beam Assist will
turn off.

- If the headlight switch is placed
from AUTO to another position
(headlight/position/off), High
Beam Assist will turn off and the
corresponding lamp will turn on.
[
When High Beam Assist is operating,
high beam switches to low beam if
any of the following conditions occur:

- When the headlight of an oncoming
vehicle is detected.

- When the tail lamp of a vehicle in
front is detected.

- When the headlight or tail lamp of a
motorcycle or a bicycle is detected.

- When the surrounding ambient light
is bright enough that high beams
are not required.

- When streetlights or other lights are
detected.
Information
The images and colors in the cluster may
differ depending on the cluster type or
theme selected from the cluster.

Convenience Features5-104
High Beam Assist Malfunction
and Limitations
High Beam Assist malfunction
B0179EU04
When High Beam Assist is not working
properly, the ‘Check High Beam Assist
(HBA) system’ warning message
will appear and
warning light will
illuminate on the cluster. Have the
function be inspected by an authorized
HYUNDAI dealer.
Limitations of High Beam Assist

[ Light from an oncoming or front
vehicle is not detected because of
lamp damage, or because it is hidden
from sight, etc.

[ Headlight of an oncoming or front
vehicle is covered with dust, snow or
water.

[ An oncoming or front vehicle’s
headlights are off, but the fog lamps
are on, etc.

[ There is a lamp that has a similar
shape as a vehicle’s lamp.

[ Headlights have been damaged or not
repaired properly.

[ Headlights are not aimed properly.

[ Driving on a narrow-curved road,
curved road, rough road, uphill or
downhill.

[ Vehicle in front is partially visible on a
crossroad or curved road.
[
There is a traffic light, reflecting sign,
flashing sign or mirror ahead.

[ There is a temporary reflector or flash
ahead (construction area).

[ The road conditions are bad such as
being wet, iced or covered with snow.

[ A vehicle suddenly appears from a
curve.

[ The vehicle is tilted from a flat tire or
is being towed.

[ Light from an oncoming or front
vehicle is not detected due to
obstacles in the air such as exhaust
fume, smoke, fog, snow, or water spay
or blizzard on the road, or fogging in
the lamp, etc.
Information
For more details on the limitations of the
Front View Camera, refer to “Forward
Collision-Avoidance Assist (FCA)” section
in chapter 7.
WARNING

[At times, High Beam Assist may not
work properly. High Beam Assist is
for your convenience only. It is the
responsibility of the driver for safe
driving practices and always check
the road conditions for your safety.

[ When High Beam Assist does not
operate normally, change the
headlight position manually between
high beam and low beam.

[ High Beam Assist may not operate
for 15 seconds after the vehicle is
started, or the front view camera is
initialized.

05
5-105
INTERIOR LIGHTS
WARNING
Do not use the interior lights when
driving in the dark. The interior lights
may obscure your view and cause an
accident.
NOTICE
Do not use the interior lights for
extended periods when the vehicle is
turned off or the battery will discharge.
Interior Lamp AUTO Off
The interior lamps will automatically go
off approximately 20 minutes after the
vehicle is turned off and the doors are
closed. If a door is opened, the lamp
will go off 25 minutes after the vehicle
is turned off. If the doors are locked by
the smart key and the vehicle enters the
armed stage of the theft alarm system,
the lamps will go off five seconds later.
)URQW/DPSV
B0903EU03
Front map lamp ():
Touch either icons to turn the map lamp
on or off. This light produces a spot
beam for convenient use as a map lamp
at night or as a personal lamp for the
driver and the front passenger.
Door lamp ( ):
The front or rear room lamps come on
when the front or rear doors are opened.
When doors are unlocked by the smart
key, the front and rear lamps come on
for approximately 30 seconds as long as
any door is not opened. The front and
rear room lamps go out gradually after
approximately 30 seconds when the door
is closed. However, if the ignition switch
or Engine Start/Stop button is in the ON
position or all doors are locked, the front
and rear lamps will turn off. If a door is
opened with the ignition switch in the
ACC position or the LOCK/OFF position,
the front and rear lamps will stay on for
about 5 minutes.
Room lamp (()
Press the button to turn ON the room
lamp for the front and rear seats.

Convenience Features5-106
Rear Lamps
B0192KO01

[ :
Touch the icon to turn either lamp on
or off.
Vanity Mirror Lamp
B0194KO04
Opening the lid of the vanity mirror will
automatically turn on the mirror lamp.
Glove Box Lamp
B0195KO01
The glove box lamp turns on when the
glove box is opened.
If the glove box is not closed, the lamp
will turn off after 20 minutes.
NOTICE
To prevent unnecessary charging
system drain, close the glove box
securely after using the glove box.

05
5-107
Door Courtesy Lamp (if
equipped)
B0918KO01
The lamp turns on when a door is open
and turns off when the door is closed.
Luggage Compartment Lamp
B0197KO01

[ON () :
The luggage compartment lamp stays
on at all times.

[ DOOR (
) :
The luggage compartment lamp
comes on when the liftgate is opened.

[ OFF (
) :
The luggage compartment lamp is off.
Puddle Lamp
Welcome light
B0198KO01
When all doors (and liftgate) are closed
and locked, the puddle lamp will turn on
for 15 seconds if the door is unlocked by
the smart key or when you put your hand
in the outside door handle with the smart
key in possession.
For more details, refer to “Welcome
System” in this chapter.
Escort light
When the ignition switch is in the LOCK/
OFF position and the driver’s door is
opened, the puddle lamp will turn on for
30 seconds. If the driver’s door is closed
within the 30 second period, the puddle
lamp will turn off after 15 seconds. If the
driver’s door is closed and locked, the
puddle lamp will turn off immediately.
The Puddle Lamp Escort Light will turn
on only the first time the driver’s door is
opened after the engine is turned off.

Convenience Features5-108
Welcome System
B0189KO00
Welcome system helps keep the driver
visible by turning on vehicle lights when
the driver approaches the vehicle.
Puddle lamp and door handle lamp
When all the doors (and liftgate) are
closed and locked, the puddle lamp
and door handle lamp will turn on for
approximately 15 seconds if:
When all the doors (and liftgate) are
closed and locked, the puddle light and
door handle light turn on for about 15
seconds if:

[ &RQYHQLHQFH

05
5-109
Headlight and position lamp
When the light switch is ON, and all
the doors (and liftgate) are closed and
locked, the headlight and position lamp
will turn on for approximately 15 seconds
if the door unlock button is pressed
on the smart key. Note that if the light
switch is in the AUTO position, the
headlight and position light will turn on
only when it is dark outside.
6HOHFW
S6HWXS

Convenience Features5-110
B0200KO01
)URQW:LQGVKLHOG:LSHUV
Operates as follows when the ignition
switch or Engine Start/Stop button is in
the ON position.
MIST: For a single wiping cycle, push the lever upward and release. The
wipers will operate continuously
if the lever is held in this position.
OFF: Wiper is not in operation.
AUTO
(if equipped): The rain sensor located
on the upper end of the
windshield glass senses
the amount of rainfall and
controls the wiping cycle
for the proper interval. The
more it rains, the faster
the wiper operates. When
the rain stops, the wiper
stops. To vary the speed
setting, turn the speed
control knob.
LO: The wiper runs at a lower speed.
HI: The wiper runs at a higher speed.
Information
If there is heavy accumulation of snow
or ice on the windshield, defrost the
windshield for about 10 minutes, or until
the snow and/or ice is removed before
using the windshield wipers to ensure
proper operation.
If you do not remove the snow and/or ice
before using the wiper and washer, it may
damage the wiper and washer system.
AUTO wiper control (if equipped)
B0200KO02
The rain sensor located on the upper
end of the windshield glass senses
the amount of rainfall and controls the
wiping cycle for the proper interval.
The wiper operation time will be
automatically controlled depends on
rainfall.
When the rain stops, the wiper stops.
To vary the sensitivity setting, turn the
sensitivity control knob.
If the wiper switch is set in AUTO mode
when the ignition switch is in the ON
position, the wiper will operate once to
perform a self-check of the system. Set
the wiper to the OFF position when the
wiper is not in use.
WIPERS AND WASHERS

05
5-111
WARNING
To avoid personal injury from the
windshield wipers, when the engine
is running and the windshield wiper
switch is placed in the AUTO mode:

[Do not touch the upper end of the
windshield glass facing the rain
sensor.

[ Do not wipe the upper end of the
windshield glass with a damp or wet
cloth.

[ Do not put pressure on the
windshield glass.
NOTICE

[When washing the vehicle, set the
ZLSHUVZLWFKLQWKH2))SRVLWLRQWR
stop the auto wiper operation. The
wiper may operate and be damaged
if the switch is set in the AUTO mode
while washing the vehicle.

[ Do not remove the sensor cover
located on the upper end of the
passenger side windshield glass.
Damage to system components
could occur and may not be covered
by your vehicle warranty.

[ Because of using a photo sensor,
temporary malfunction could occur
according to sudden ambient light
change made by stone and dust
while driving.
)URQW:LQGVKLHOG:DVKHUV
B0201KO01
In the OFF position, pull the lever gently
toward you to spray washer fluid on the
windshield and to run the wipers 1-3
cycles. The spray and wiper operation
will continue until you release the lever. If
the washer does not work, you may need
to add washer fluid to the washer fluid
reservoir.