torque INFINITI FX35 2004 User Guide

AT-36
A/T CONTROL SYSTEM
Revision: 2004 November 2004 FX35/FX45
Engine Brake ControlACS002LL

The forward one-way clutch transmits the drive force from the engine to the rear wheels. But the reverse
drive from the rear wheels is not transmitted to the engine because the one-way clutch is idling.
Therefore, the low coast brake solenoid is operated to prevent the forward one-way clutch from idling and
the engine brake is operated in the same manner as conventionally.

The operation of the low coast brake solenoid switches the low coast brake switching valve and controls
the coupling and releasing of the low coast brake.
The low coast brake reducing valve controls the low coast brake coupling force.
Control ValveACS002LM
FUNCTION OF CONTROL VALVE
SCIA1520E
Name Function
Torque converter regulator valveIn order to prevent the pressure supplied to the torque converter from being excessive,
the line pressure is adjusted to the optimum pressure (torque converter operating pres-
sure).
Pressure regulator valve
Pressure regulator plug
Pressure regulator sleeveAdjusts the oil discharged from the oil pump to the optimum pressure (line pressure) for
the driving state.
Front brake control valveWhen the front brake is coupled, adjusts the line pressure to the optimum pressure
(front brake pressure) and supplies it to the front brake. (In 1st, 2nd, 3rd, and 5th gears,
adjusts the clutch pressure.)
Accumulator control valveAdjusts the pressure (accumulator control pressure) acting on the accumulator piston
and low coast reducing valve to the pressure appropriate to the driving state.
Pilot valve AAdjusts the line pressure and produces the constant pressure (pilot pressure) required
for line pressure control, shift change control, and lock-up control.
Pilot valve BAdjusts the line pressure and produces the constant pressure (pilot pressure) required
for shift change control.
Low coast brake switching valve During engine braking, supplies the line pressure to the low coast brake reducing valve.
Low coast brake reducing valveWhen the low coast brake is coupled, adjusts the line pressure to the optimum pressure
(low coast brake pressure) and supplies it to the low coast brake.
N-R accumulator Produces the stabilizing pressure for when N-R is selected.
Direct clutch piston switching valve Operates in 4th gear and switches the direct clutch coupling capacity.
High and low reverse clutch control valveWhen the high and low reverse clutch is coupled, adjusts the line pressure to the opti-
mum pressure (high and low reverse clutch pressure) and supplies it to the high and low
reverse clutch. (In 1st, 3rd, 4th and 5th gears, adjusts the clutch pressure.)

A/T CONTROL SYSTEM
AT-37
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
FUNCTION OF ATF PRESSURE SWITCH
Input clutch control valveWhen the input clutch is coupled, adjusts the line pressure to the optimum pressure
(input clutch pressure) and supplies it to the input clutch. (In 4th and 5th gears, adjusts
the clutch pressure.)
Direct clutch control valveWhen the direct clutch is coupled, adjusts the line pressure to the optimum pressure
(direct clutch pressure) and supplies it to the direct clutch. (In 2nd, 3rd, and 4th gears,
adjusts the clutch pressure.)
TCC control valve
TCC control plug
TCC control sleeveSwitches the lock-up to operating or released. Also, by performing the lock-up operation
transiently, lock-up smoothly.
Torque converter lubrication valveOperates during lock-up to switch the torque converter, cooling, and lubrication system
oil path.
Cool bypass valve Allows excess oil to bypass cooler circuit without being fed into it.
Line pressure relief valve Discharges excess oil from line pressure circuit.
N-D accumulator Produces the stabilizing pressure for when N-D is selected.
Manual valveSends line pressure to each circuit according to the select position. The circuits to which
the line pressure is not sent drain. Name Function
Name Function
ATF pressure switch 1 (FR/B)Detects any malfunction in the front brake hydraulic pressure. When it detects any mal-
function, it puts the system into fail-safe mode.
ATF pressure switch 2 (LC/B)Detects any malfunction in the low coast brake hydraulic pressure. When it detects any
malfunction, it puts the system into fail-safe mode.
ATF pressure switch 3 (I/C)Detects any malfunction in the input clutch hydraulic pressure. When it detects any mal-
function, it puts the system into fail-safe mode.
ATF pressure switch 5 (D/C)Detects any malfunction in the direct clutch hydraulic pressure. When it detects any mal-
function, it puts the system into fail-safe mode.
ATF pressure switch 6 (HLR/C)Detects any malfunction in the high and low reverse clutch hydraulic pressure. When it
detects any malfunction, it puts the system into fail-safe mode.

TROUBLE DIAGNOSIS
AT-43
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
A/T Interlock

If there is an A/T interlock judgment malfunction, the transmission is fixed in 2nd gear to make driving pos-
sible.
NOTE:
When the vehicle is driven fixed in 2nd gear a turbine revolution sensor malfunction is displayed,
but this is not a turbine revolution sensor malfunction.

When the coupling pattern below is detected, the fail-safe action corresponding to the pattern is executed.
A/T INTERLOCK COUPLING PATTERN TABLE

: NG X: OK
A/T 1st Engine Braking

When there is an A/T first gear engine brake judgment malfunction, the low coast brake solenoid is
switched “OFF” to avoid the engine brake operation.
Line Pressure Solenoid

The solenoid is switched “OFF” and the line pressure is set to the maximum hydraulic pressure to make
driving possible.
Torque Converter Clutch Solenoid

The solenoid is switched “OFF” to release the lock-up.
Low Coast Brake Solenoid

When a malfunction (electrical or functional) occurs, in order to make driving possible, if the solenoid is
“ON”, the transmission is held in 2nd gear; if the solenoid is “OFF”, the transmission is held in 4th gear.
(engine brake is not applied in 1st and 2nd gear.)
Input Clutch Solenoid

If a malfunction (electrical or functional) occurs with the solenoid either “ON” or “OFF”, the transmission is
held in 4th gear to make driving possible.
Direct Clutch Solenoid

If a malfunction (electrical or functional) occurs with the solenoid either “ON” or “OFF”, the transmission is
held in 4th gear to make driving possible.
Front Brake Solenoid

If a malfunction (electrical or functional) occurs with the solenoid “ON”, in order to make driving possible,
the A/T is held in 5th gear; if the solenoid is OFF, 4th gear.
High and Low Reverse Clutch Solenoid

If a malfunction (electrical or functional) occurs with the solenoid either “ON” or “OFF”, the transmission is
held in 4th gear to make driving possible.
Turbine Revolution Sensor 1 or 2

The control is the same as if there were no turbine revolution sensors, 5th gear and manual mode are pro-
hibited.
Gear positionATF pressure switch output
Fail-safe
functionClutch pressure output pattern after fail-safe func-
tion
SW3
(I/C)SW6
(HLR/
C)SW5
(D/C)SW1
(FR/B)SW2
(LC/B)I/C HLR/C D/C FR/B LC/B L/U
A/T inter-
lock cou-
pling pattern3rd – X X –
Held in
2nd gearOFF OFF ON OFF OFF OFF
4th – X X –
Held in
2nd gearOFF OFF ON OFF OFF OFF
5th X X – X
Held in
2nd gearOFF OFF ON OFF OFF OFF

AT-46
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
DIAGNOSTIC WORKSHEET
Information From Customer
KEY POINTS

WHAT..... Vehicle and A/T model

WHEN..... Date, Frequencies

WHERE..... Road conditions

HOW..... Operating conditions, Symptoms
Diagnostic Worksheet Chart
Customer name MR/MS Model and Year VIN
Trans. Model Engine Mileage
Incident Date Manuf. Date In Service Date
Frequency❏ Continuous❏ Intermittent ( times a day)
Symptoms❏ Vehicle does not move. (❏ Any position❏ Particular position)
❏ No up-shift (❏ 1st → 2nd❏ 2nd → 3rd❏ 3rd → 4th ❏ 4th → 5th)
❏ No down-shift (❏ 5th → 4th ❏ 4th → 3rd❏ 3rd → 2nd❏ 2nd → 1st)
❏ Lock-up malfunction
❏ Shift point too high or too low.
❏ Shift shock or slip (❏ N → D❏ Lock-up❏ Any drive position)
❏ Noise or vibration
❏ No kick down
❏ No pattern select
❏ Others
()
A/T CHECK indicator lamp Blinks for about 8 seconds.
❏ Continuously lit❏ Not lit
Malfunction indicator lamp (MIL)❏ Continuously lit❏ Not lit
1❏ Read the item on “cautions concerning fail-safe and understand the customer's complaint.AT- 4 2
2❏ A/T fluid inspection
AT- 5 1❏ Leak (Repair leak location.)
❏ State
❏ Amount
3❏ Stall test and line pressure test
AT- 5 1
,
AT- 5 2
❏ Stall test
❏ Torque converter one-way clutch
❏ Front brake
❏ High and low reverse clutch
❏ Low coast brake
❏ Forward brake
❏ Reverse brake
❏ Forward one-way clutch❏ 1st one-way clutch
❏ 3rd one-way clutch
❏ Engine
❏ Line pressure low
❏ Except for input clutch and direct
clutch, clutches and brakes OK
❏ Line pressure inspection - Suspected part:

TROUBLE DIAGNOSIS
AT-47
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
4❏ Execute all road tests and enter checks in required inspection items.AT- 5 4
4-1.Check before engine is started
AT- 5 5
❏ The A/T CHECK Indicator Lamp does come on. AT- 1 9 1 .
❏ Perform self-diagnostics. Enter checks for detected items. AT- 9 4
, AT-103
❏ AT-105, "DTC U1000 CAN COMMUNICATION LINE" .
❏ AT-108, "
DTC P0615 START SIGNAL CIRCUIT" .
❏ AT-112, "
DTC P0705 PARK/NEUTRAL POSITION SWITCH" .
❏ AT-116, "
DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)" .
❏ AT-121, "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT-121, "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT-123, "
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE" .
❏ AT-125, "
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)" .
❏ AT-127, "
DTC P0745 LINE PRESSURE SOLENOID VALVE" .
❏ AT-129, "
DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)" .
❏ AT-133, "
DTC P1702 TRANSMISSION CONTROL MODULE (RAM)" .
❏ AT-134, "
DTC P1703 TRANSMISSION CONTROL MODULE (ROM)" .
❏ AT-135, "
DTC P1704 TRANSMISSION CONTROL MODULE (EEPROM)" .
❏ AT-136, "
DTC P1705 THROTTLE POSITION SENSOR" .
❏ AT-139, "
DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT" .
❏ AT-143, "
DTC P1716 TURBINE REVOLUTION SENSOR" .
❏ AT-145, "
DTC P1721 VEHICLE SPEED SENSOR MTR" .
❏ AT-147, "
DTC P1730 A/T INTERLOCK" .
❏ AT-150, "
DTC P1731 A/T 1ST ENGINE BRAKING" .
❏ AT-152, "
DTC P1752 INPUT CLUTCH SOLENOID VALVE" .
❏ AT-154, "
DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-156, "
DTC P1757 FRONT BRAKE SOLENOID VALVE" .
❏ AT-158, "
DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-160, "
DTC P1762 DIRECT CLUTCH SOLENOID VALVE" .
❏ AT-162, "
DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-164, "
DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE" .
❏ AT-166, "
DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION" .
❏ AT-168, "
DTC P1772 LOW COAST BRAKE SOLENOID VALVE" .
❏ AT-170, "
DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-172, "
DTC P1815 MANUAL MODE SWITCH" .
❏ AT-178, "
DTC P1841 ATF PRESSURE SWITCH 1" .
❏ AT-180, "
DTC P1843 ATF PRESSURE SWITCH 3" .
❏ AT-182, "
DTC P1845 ATF PRESSURE SWITCH 5" .
❏ AT-184, "
DTC P1846 ATF PRESSURE SWITCH 6" .
4-2.Check at Idle
AT- 5 5
❏ AT- 1 9 3 , "Engine Cannot Be Started In “P” or “N” Position" .
❏ AT- 1 9 3 , "
In “P” Position, Vehicle Moves When Pushed" .
❏ AT- 1 9 4 , "
In “N” Position, Vehicle Moves" .
❏ AT- 1 9 5 , "
Large Shock (“N” to “D” Position)" .
❏ AT- 1 9 8 , "
Vehicle Does Not Creep Backward In “R” Position" .
❏ AT- 2 0 1 , "
Vehicle Does Not Creep Forward In “D” Position" .
4-3.Cruise test
AT- 5 7
Part 1
❏ AT- 2 0 3 , "
Vehicle Cannot Be Started From D1" .
❏ AT- 2 0 6 , "
A/T Does Not Shift: D1 → D2" .
❏ AT- 2 0 8 , "
A/T Does Not Shift: D2 → D3" .
❏ AT- 2 11 , "
A/T Does Not Shift: D3 → D4" .
❏ AT- 2 1 3 , "
A/T Does Not Shift: D4 → D5" .
❏ AT- 2 1 6 , "
A/T Does Not Perform Lock-up"
❏ AT- 2 1 8 , "A/T Does Not Hold Lock-up Condition" .
❏ AT- 2 2 0 , "
Lock-up Is Not Released" .
❏ AT- 2 2 1 , "
Engine Speed Does Not Return To Idle" .

AT-48
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
44-3Part 2
AT- 6 0
❏ AT-203, "Vehicle Cannot Be Started From D1" .
❏ AT-206, "
A/T Does Not Shift: D1 → D2" .
❏ AT-208, "
A/T Does Not Shift: D2 → D3" .
❏ AT- 2 11 , "
A/T Does Not Shift: D3 → D4" .
Part 3
AT- 6 1
❏ AT-222, "Cannot Be Changed to Manual Mode" .
❏ AT-223, "
A/T Does Not Shift: 5th gear → 4th gear" .
❏ AT-225, "
A/T Does Not Shift: 4th gear → 3rd gear" .
❏ AT-227, "
A/T Does Not Shift: 3rd gear → 2nd gear" .
❏ AT-229, "
A/T Does Not Shift: 2nd gear → 1st gear" .
❏ AT-231, "
Vehicle Does Not Decelerate By Engine Brake" .
❏ Perform self-diagnostics. Enter checks for detected items. AT- 9 4
, AT-103
❏ AT-105, "DTC U1000 CAN COMMUNICATION LINE" .
❏ AT-108, "
DTC P0615 START SIGNAL CIRCUIT" .
❏ AT- 11 2 , "
DTC P0705 PARK/NEUTRAL POSITION SWITCH" .
❏ AT- 11 6 , "
DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)" .
❏ AT-121, "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT-121, "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT-123, "
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE" .
❏ AT-125, "
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)" .
❏ AT-127, "
DTC P0745 LINE PRESSURE SOLENOID VALVE" .
❏ AT-129, "
DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)" .
❏ AT-133, "
DTC P1702 TRANSMISSION CONTROL MODULE (RAM)" .
❏ AT-134, "
DTC P1703 TRANSMISSION CONTROL MODULE (ROM)" .
❏ AT-135, "
DTC P1704 TRANSMISSION CONTROL MODULE (EEPROM)" .
❏ AT-136, "
DTC P1705 THROTTLE POSITION SENSOR" .
❏ AT-139, "
DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT" .
❏ AT-143, "
DTC P1716 TURBINE REVOLUTION SENSOR" .
❏ AT-145, "
DTC P1721 VEHICLE SPEED SENSOR MTR" .
❏ AT-147, "
DTC P1730 A/T INTERLOCK" .
❏ AT-150, "
DTC P1731 A/T 1ST ENGINE BRAKING" .
❏ AT-152, "
DTC P1752 INPUT CLUTCH SOLENOID VALVE" .
❏ AT-154, "
DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-156, "
DTC P1757 FRONT BRAKE SOLENOID VALVE" .
❏ AT-158, "
DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-160, "
DTC P1762 DIRECT CLUTCH SOLENOID VALVE" .
❏ AT-162, "
DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-164, "
DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE" .
❏ AT-166, "
DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION" .
❏ AT-168, "
DTC P1772 LOW COAST BRAKE SOLENOID VALVE" .
❏ AT-170, "
DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-172, "
DTC P1815 MANUAL MODE SWITCH" .
❏ AT-178, "
DTC P1841 ATF PRESSURE SWITCH 1" .
❏ AT-180, "
DTC P1843 ATF PRESSURE SWITCH 3" .
❏ AT-182, "
DTC P1845 ATF PRESSURE SWITCH 5" .
❏ AT-184, "
DTC P1846 ATF PRESSURE SWITCH 6" .
5❏ Inspect each system for items found to be NG in the self-diagnostics and repair or replace the malfunction
parts.
6❏ Perform all road tests and enter the checks again for the required items.AT- 5 4
7❏ For any remaining NG items, perform the “diagnostics procedure” and repair or replace the malfunction parts.
See the chart for diagnostics by symptoms. (This chart also contains other symptoms and inspection proce-
dures.)AT- 6 5
8❏ Erase the results of the self-diagnostics from the TCM.AT- 4 0,
AT- 1 0 4

AT-52
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
CAUTION:
Run the engine at idle for at least one minute.
Judgement Stall Test
O: Stall speed within standard value position
H: Stall speed higher than standard value
L: Stall speed lower than standard value
Stall test standard value position
LINE PRESSURE TEST
Line Pressure Test Port
Line Pressure Test Procedure
1. Inspect the amount of engine oil and replenish if necessary.
2. Drive the car for about 10 minutes to warm it up so that the A/T fluid reaches in range of 50 to 80°C (122
to 176°F), then inspect the amount of A/T fluid and replenish if necessary.
NOTE:
The A/T fluid temperature rises in range of 50 to 80°C (122 to 176°F) during 10 minutes of driving.
3. Remove front propeller shaft from vehicle (with AWD models). Refer to PR-4, "
Removal and Installation" . Stall speed:
VQ35DE engine: 2,650 - 2,950 rpm
VK45DE engine: 2,300 - 2,600 rpm
Selector lever position
Expected problem location
D, M R
Stall speedHO

Forward brake

Forward one-way clutch

1st one-way clutch

3rd one-way clutch
OH

Reverse brake
LL

Engine and torque converter one-way clutch
HH

Line pressure low
Does not shift up D, M position 1 → 2 Slipping in 2nd, 3rd, 4th gears Direct clutch slippage
Does not shift up D, M position 2 → 3 Slipping in 3rd, 4th, 5th gears high and low reverse clutch slippage
Does not shift up D, M position 3 → 4 Slipping in 4th, 5th gears Input clutch slippage
Does not shift up D, M position 4 → 5 Slipping in 5th gear Front brake slippage
SCIA2187E

TROUBLE DIAGNOSIS
AT-53
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
4. After warming up remove the oil pressure detection plug and
install the oil pressure gauge [ST2505S001(J-34301-C)].
CAUTION:
When using the oil pressure gauge, be sure to use the O-
ring attached to the oil pressure detection plug.
5. Securely engage the parking brake so that the tires do not turn.
6. Start the engine, then measure the line pressure at both idle and
the stall speed.
CAUTION:

Keep the brake pedal pressed all the way down during
measurement.

When measuring the line pressure at the stall speed,
refer to AT- 5 1 , "
STALL TEST" .
7. After the measurements are complete, install the oil pressure
detection plug and tighten to the regulation torque below.
CAUTION:
Do not reuse the O-ring.
Line Pressure
SCIA5309E
SCIA1224E
:7.3 N·m (0.74 kg-m, 65 in-lb)SAT493G
Engine speedLine pressure [kPa (kg/cm
2 , psi)]
R position D, M positions
At idle speed 392 - 441 (4.0 - 4.5, 57 - 64) 373 - 422 (3.8 - 4.3, 54 - 61)
At stall speed 1,700 - 1,890 (17.3 - 19.3, 247 - 274) 1,310 - 1,500 (13.3 - 15.3, 190 - 218)

TROUBLE DIAGNOSIS
AT-67
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
6
Shift
ShockShock is too large for
downshift when accel-
erator pedal is
pressed.ON vehicle1. Accelerator pedal position sensorAT-136
2. Control linkage adjustmentAT-234
3. CAN communication lineAT-105
4. Engine speed signalAT-121
5. Turbine revolution sensorAT-143
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT-145
7. Fluid level and stateAT- 5 1
8. Control valve with TCMAT-242
OFF vehicle9. Front brake (brake band)AT-27410. Input clutch AT-308
11. High and low reverse clutchAT-320
12. Direct clutchAT-323
7Shock is too large for
upshift when acceler-
ator pedal is released.ON vehicle1. Accelerator pedal position sensorAT-136
2. Control linkage adjustmentAT-234
3. Engine speed signalAT-121
4. CAN communication lineAT-105
5. Turbine revolution sensorAT-143
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT-145
7. Fluid level and stateAT- 5 1
8. Control valve with TCMAT-242
OFF vehicle9. Front brake (brake band)AT-27410. Input clutch AT-308
11. High and low reverse clutch AT-320
12. Direct clutch AT-323
8Shock is too large for
lock-up.ON vehicle1. Accelerator pedal position sensorAT-136
2. Control linkage adjustmentAT-234
3. Engine speed signalAT-121
4. CAN communication lineAT-105
5. Turbine revolution sensorAT-143
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT-145
7. Torque converter clutch solenoid valveAT-123
8. Fluid level and stateAT- 5 1
9. Control valve with TCMAT-242
OFF vehicle 10. Torque converterAT-286
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-73
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
23
Slips/Will
Not
EngageVehicle cannot be
started from D
1 .
Refer to AT-203,
"Vehicle Cannot Be
Started From D1" .ON vehicle1. Fluid level and stateAT- 5 1
2. Accelerator pedal position sensorAT-136
3. Line pressure testAT- 5 2
4. CAN communication lineAT-105
5. Control valve with TCMAT-242
OFF vehicle6. Torque converterAT-286
7. Oil pump assemblyAT-303
8. 3rd one-way clutchAT-306
9. 1st one-way clutch AT-314
10. Gear systemAT-274
11. Reverse brakeAT-286
12. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 7 , "
Cross-Sectional View (2WD Models)" or AT- 1 8 ,
"Cross-Sectional View (AWD Models)" )AT-286
13. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-17,
"Cross-Sectional View (2WD Models)" or AT-18, "Cross-
Sectional View (AWD Models)" )AT-286
24Does not lock-up.
Refer to AT-216, "A/T
Does Not Perform
Lock-up" .ON vehicle1. Fluid level and stateAT- 5 1
2. Line pressure testAT- 5 2
3. Engine speed signalAT-121
4. Turbine revolution sensorAT-143
5. Torque converter clutch solenoid valveAT-123
6. CAN communication lineAT-105
7. Control valve with TCMAT-242
OFF vehicle8. Torque converterAT-2869. Oil pump assemblyAT-303
25Does not hold lock-up
condition.
Refer to AT-218, "A/T
Does Not Hold Lock-
up Condition" .ON vehicle1. Fluid level and stateAT- 5 1
2. Line pressure testAT- 5 2
3. Engine speed signalAT-121
4. Turbine revolution sensorAT-143
5. Torque converter clutch solenoid valveAT-123
6. CAN communication lineAT-105
7. Control valve with TCMAT-242
OFF vehicle8. Torque converterAT-2869. Oil pump assemblyAT-303
No. Items Symptom Condition Diagnostic ItemReference
page