control INFINITI FX35 2004 Service Manual

ATC-126
HEATER & COOLING UNIT ASSEMBLY
Revision: 2004 November 2004 FX35/FX45
HEATER & COOLING UNIT ASSEMBLYPFP:27110
Removal and InstallationAJS0015J
REMOVAL
1. Use a refrigerant collecting equipment (for HFC-134a) to discharge refrigerant.
2. Drain coolant from cooling system. Refer to CO-11, "
Changing Engine Coolant" (VQ35DE) or CO-36,
"Changing Engine Coolant" (VK45DE).
3. Remove cowl top cover. Refer to EI-24, "
COWL TOP" .
4. Remove high-pressure pipe 2 mounting clip.
5. Remove low-pressure flexible hose bracket mounting bolts.
6. Disconnect evaporator-side one touch joint.
a. Set a disconnector (High-pressure side: 92530-89908, Low-
pressure side: 92530-89916) on A/C piping.
b. Slide a disconnector toward vehicle front until it clicks.
c. Slide A/C piping toward vehicle front and disconnect it.
CAUTION:
Seal connection opening of piping with a cap or vinyl tape
to avoid exposure to atmosphere.
7. Remove electronic control throttle assembly (VQ35DE). Refer to
EM-19, "
INTAKE MANIFOLD COLLECTOR" .
8. Disconnect two heater hoses from heater core.
9. Remove instrument panel assembly. Refer to IP-11, "
Removal
and Installation" .
10. Remove blower unit. Refer to ATC-121, "
BLOWER UNIT" .
11. Remove instrument stays (driver side and passenger side).
RJIA2037E
RJIA2041E
RJIA2077E
RJIA2042E

REFRIGERANT LINES
ATC-159
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2004 November 2004 FX35/FX45
CHECKING PROCEDURE
To prevent inaccurate or false readings, make sure there is no refrigerant vapor, shop chemicals, or cigarette
smoke in the vicinity of the vehicle. Perform the leak test in calm area (low air/wind movement) so that the
leaking refrigerant is not dispersed.
1. Turn engine OFF.
2. Connect a suitable A/C manifold gauge set to the A/C service ports.
3. Check if the A/C refrigerant pressure is at least 345 kPa (3.52 kg/cm
2 , 50 psi) above 16°C (61°F). If less
than specification, recover/evacuate and recharge the system with the specified amount of refrigerant.
NOTE:
At temperatures below 16°C (61°F), leaks may not be detected since the system may not reach 345 kPa
(3.52 kg/cm
2 , 50 psi).
4. Perform the leak test from the high-pressure side (compressor discharge a to evaporator inlet h) to the
low-pressure side [evaporator drain hose i to shaft seal o (VK45DE) or n (VQ35DE)]. Refer to ATC-139,
"Components" . Perform a leak check for the following areas carefully. Clean the component to be
checked and move the leak detected probe completely around the connection/component.
Compressor
Check the fitting of high- and low-pressure hoses, relief valve and shaft seal.
Liquid tank
Check the refrigerant connection.
Service valves
Check all around the service valves. Ensure service valve caps are secured on the service valves (to pre-
vent leaks).
NOTE:
After removing A/C manifold gauge set from service valves, wipe any residue from valves to prevent any
false readings by leak detector.
Cooling unit (Evaporator)
With engine OFF, turn blower fan on “High” for at least 15 seconds to dissipate any refrigerant trace in the
cooling unit. Wait a minimum of 10 minutes accumulation time (refer to the manufacturer′s recommended
procedure for actual wait time) before inserting the leak detector probe into the drain hose.
Keep the probe inserted for at least 10 seconds. Use caution not to contaminate the probe tip with water
or dirt that may be in the drain hose.
5. If a leak detector detects a leak, verify at least once by blowing compressed air into area of suspected
leak, then repeat check as outlined above.
6. Do not stop when one leak is found. Continue to check for additional leaks at all system components.
If no leaks are found, perform steps 7-10.
7. Start engine.
8. Set the heater A/C control as follows;
a. A/C switch: ON
b. Face mode
c. Intake position: Recirculation
d. Max cold temperature
e. Fan speed: High
9. Run engine at 1,500 rpm for at least 2 minutes.
10. Turn engine off and perform leak check again following steps 4 through 6 above.

AV-2Revision: 2004 November 2004 FX35/FX45Antenna Amp. Inspection ....................................... 51
Location of Antenna ................................................ 52
Window Antenna Repair ......................................... 52
CHECK ELEMENT .............................................. 52
Removal and Installation of Roof Antenna ............. 54
REMOVAL ........................................................... 54
INSTALLATION .................................................... 54
INTEGRATED DISPLAY SYSTEM ............................ 55
System Description ................................................. 55
A/C AND AV SWITCH SYSTEM .......................... 55
PRECAUTION OF LCD MONITOR ..................... 55
POWER SUPPLY AND GROUND ....................... 55
DRIVE COMPUTER ............................................ 56
E/M SWITCH ....................................................... 57
SETTING SCREEN ............................................. 58
WARNING INDICATIONS ................................... 59
AV COMMUNICATION LINE ............................... 59
CAN Communication System Description .............. 60
CAN Communication Unit ....................................... 61
Component Parts and Harness Connector Location ... 61
Schematic ............................................................... 62
Wiring Diagram — INF/D — ................................... 63
Schematic ............................................................... 68
Wiring Diagram — COMM — ................................. 69
Terminals and Reference Value for Display Unit .... 72
Terminals and Reference Value for A/C and AV
Switch ..................................................................... 73
On Board Self-Diagnosis Function ......................... 74
DESCRIPTION .................................................... 74
DIAGNOSIS ITEM ............................................... 74
Self-Diagnosis Mode .............................................. 74
OPERATION PROCEDURES ............................. 74
NETWORK CHECK ............................................. 75
PARTS CHECK ................................................... 76
HVAC DETAIL SCREEN ...................................... 76
VERSION CHECK ............................................... 76
CAN DIAG MNTR (CAN DIAG MONITOR) ......... 76
A/C and AV Switch Self-Diagnosis Function ........... 77
STARTING THE SELF-DIAGNOSIS MODE ........ 77
DIAGNOSIS FUNCTION ..................................... 77
EXITING THE SELF-DIAGNOSIS MODE ........... 77
Trouble Diagnosis Chart by Symptom .................... 78
Power Supply and Ground Circuit Check for Display
Unit ......................................................................... 79
Power Supply and Ground Circuit Check for A/C and
AV Switch ................................................................ 80
Vehicle Speed Signal Inspection ............................ 80
Illumination Signal Inspection ................................. 81
Ignition Signal Inspection ........................................ 82
Audio Communication Line Inspection ................... 82
A/C and AV Switch Does Not Operate .................... 84
CAN Communication Line Inspection ..................... 85
Audio Steering Wheel Switch Inspection ................ 85
Removal and Installation of Display ........................ 87
REMOVAL ........................................................... 87
INSTALLATION .................................................... 87
Removal and Installation of A/C and AV Switch ..... 87
NAVIGATION SYSTEM ............................................. 88
System Description ................................................. 88TRAVEL DISTANCE ............................................ 88
TRAVEL DIRECTION .......................................... 88
MAP-MATCHING ................................................. 88
GPS (GLOBAL POSITIONING SYSTEM) .......... 89
COMPONENT DESCRIPTION ............................ 90
BIRDVIEW™ ........................................................ 90
MAP DISPLAY ..................................................... 91
FUNCTION OF CENTER SWITCH ..................... 92
“VIEW” MODE ...................................................... 98
“HEADING” MODE .............................................. 99
“NEARBY DISPLAY ICONS” MODE .................... 99
“SAVE CURRENT LOCATION” MODE ................ 99
“ADJUST CURRENT LOCATION” MODE ........... 99
“AUTO RE-ROUTE” MODE ...............................100
“AVOID AREA SETTING” MODE ......................100
“CLEAR MEMORY” MODE ................................100
“EDIT ADDRESS BOOK” MODE .......................101
“GPS INFORMATION” MODE ...........................101
“QUICK STOP CUSTOMER SETTING” MODE .101
“SET AVERAGE SPEED” MODE ......................101
“TRACKING” MODE ..........................................102
GUIDANCE VOLUME ........................................102
DISPLAY WITH PUSHED “TRIP” BUTTON .......102
TRIP 1 OR TRIP 2 .............................................103
FUEL ECONOMY ..............................................103
MAINTENANCE .................................................103
ENGINE OIL OR TIRE ROTATION ....................103
TIRE PRESSURE ..............................................104
WARNING INDICATIONS ..................................104
CAN Communication System Description ............105
CAN Communication Unit .....................................105
Component Parts Location and Harness Connector
Location ................................................................105
Schematic—NAVI— ..............................................106
Wiring Diagram —NAVI— .....................................107
Schematic — COMM — ........................................115
Wiring Diagram — COMM — ................................116
Terminals and Reference Value for NAVI Control
Unit ........................................................................121
Terminals and Reference Value for Display Control
Unit ........................................................................123
Terminals and Reference Value for Display ..........127
Terminals and Reference Value for A/C and AV
Switch ...................................................................129
On Board Self-Diagnosis Function ........................130
DESCRIPTION ..................................................130
DIAGNOSIS ITEM .............................................130
Self-Diagnosis Mode (DCU) ..................................131
OPERATION PROCEDURE ..............................131
SELF–DIAGNOSIS RESULT .............................133
Self-Diagnosis Mode (NAVI) .................................133
OPERATION PROCEDURE ..............................133
SELF–DIAGNOSIS RESULT .............................135
Confirmation/Adjustment Mode .............................136
OPERATION PROCEDURE ..............................136
DISPLAY DIAGNOSIS .......................................136
VEHICLE SIGNALS ...........................................137
AUTO CLIMATE CONTROL ..............................137
NAVIGATION .....................................................138

AV-3
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45DISPLAY DIAGNOSIS ...................................... 138
VEHICLE SIGNALS .......................................... 139
HISTORY OF ERRORS .................................... 139
DIAGNOSIS BY HISTORY OF ERRORS ......... 140
NAVIGATION .................................................... 141
Can Diag Support Monitor .................................... 143
OPERATION PROCEDURE ............................. 143
A/C and AV Switch Self-Diagnosis Function ........ 144
DESCRIPTION .................................................. 144
Power Supply and Ground Circuit Check for NAVI
Control Unit .......................................................... 145
Power Supply and Ground Circuit Check for Display
Control Unit .......................................................... 146
Power Supply and Ground Circuit Check for Display . 147
Power Supply and Ground Circuit Check for A/C and
AV Switch ............................................................. 149
Vehicle Speed Signal Check for NAVI Control Unit . 149
Vehicle Speed Signal Check for Display Control Unit . 150
Illumination Signal Check for NAVI Control Unit ... 151
Illumination Signal Check for Display Control Unit . 152
Ignition Signal Check for NAVI Control Unit ......... 152
Ignition Signal Check for Display Control Unit ..... 152
Reverse Signal Check for NAVI Control Unit ....... 152
Reverse Signal Check for Display Control Unit .... 153
When Malfunctioning Connection Between Display
Control Unit and NAVI Control Unit ...................... 153
When Malfunctioning Connection Between Display
Control Unit and Audio Unit .................................. 154
When Malfunctioning Connection Between Display
Control Unit and Display ...................................... 156
CAN Communication Line Check ......................... 158
If NAVI Control Unit Detects That DVD-ROM Map
is not Inserted ....................................................... 158
If NAVI Control Unit Detects that Inserted DVD-ROM
Map Malfunctioning or if it is Impossible to Load Data
from DVD-ROM Map ............................................ 158
If Connection Between NAVI Control Unit and GPS
Antenna is Malfunctioning .................................... 159
Color of RGB Image is Not Proper (NAVI Screen
Looks Bluish) ........................................................ 159
Color of RGB Image is Not Proper (NAVI Screen
Looks Reddish) .................................................... 160
Color of RGB Image is Not Proper (NAVI Screen
Looks Yellowish) ................................................... 161
Color of RGB Image is Not Proper (All screens Looks
Bluish) .................................................................. 162
Color of RGB Image is Not Proper (All Screens
Looks Reddish) .................................................... 163
Color of RGB Image is Not Proper (All Screens
Looks Yellowish) ................................................... 164
NAVI Screen is Rolling ......................................... 166
Guide Sound is Not Heard ................................... 167
Screen is Not Shown ............................................ 167
Operating Screen for Audio and A/C is Not Dis-
played When Showing NAVI Screen .................... 168
TRIP, FUEL ECON and MAINTENANCE Screens
are Not Shown ..................................................... 169
Average Fuel Economy Displayed is Not Shown
(“***” is Shown) ..................................................... 169Driving Distance or Average Speed is Not Shown
(“***” is Shown) .....................................................170
WARNING DOOR OPEN Screen is Not Shown ...170
TIRE PRESSURE Screen is not Shown ...............170
Unable to Operate All of A/C and AV switch (Unable
to start Self-Diagnosis) .........................................171
Position of Current-Location Mark is Not Correct . 172
Driving Test ...........................................................172
Example of Symptoms Judged Not Malfunction ...173
BASIC OPERATION ..........................................173
VEHICLE MARK ................................................173
DESTINATION, PASSING POINTS, AND MENU
ITEMS CANNOT BE SELECTED/SET ..............174
VOICE GUIDE ...................................................175
ROUTE SEARCH ..............................................175
EXAMPLES OF CURRENT-LOCATION MARK
DISPLACEMENT ..............................................176
CURRENT LOCATION MARK SHOWS A POSI-
TION WHICH IS COMPLETELY WRONG ........179
CURRENT-LOCATION MARK JUMPS .............179
CURRENT LOCATION MARK IS IN A RIVER OR
SEA ...................................................................180
WHEN DRIVING ON SAME ROAD, SOME-
TIMES CURRENT-LOCATION MARK IS IN
RIGHT PLACE AND SOMETIMES IT IS WRONG
PLACE ...............................................................180
LOCATION CORRECTION BY MAP-MATCH-
ING IS SLOW ....................................................180
ALTHOUGH GPS RECEIVING DISPLAY IS
GREEN, VEHICLE MARK DOES NOT RETURN
TO CORRECT LOCATION ................................180
NAME OF CURRENT PLACE IS NOT DIS-
PLAYED .............................................................180
CONTENTS OF DISPLAY DIFFER FOR BIRD-
VIEW™ AND THE (FLAT) MAP SCREEN ........180
Program Loading of NAVI Control Unit .................181
Removal and Installation of NAVI control Unit ......182
REMOVAL .........................................................182
INSTALLATION .................................................182
Removal and Installation of GPS Antenna ...........182
REMOVAL .........................................................182
INSTALLATION .................................................182
Removal and Installation of A/C and AV Switch ...183
Removal and Installation of Display Unit ..............183
Removal and Installation of Display Control Unit . 183
REMOVAL .........................................................183
INSTALLATION .................................................183
INFINITI MOBILE ENTERTAINMENT SYSTEM .....184
System Description ...............................................184
Component Parts and Harness Connector Location .185
Wiring Diagram – MES – ......................................186
Terminals and Reference Value for DVD Player ...188
Terminals and Reference Value for DVD Display . 189
DVD Player Is Not Work .......................................191
Screen Is Not Shown (While Sounds Come Out of
an Audio Speaker, Did not do of a Head Phone) ..193
Screen is not Shown (Sounds Come Out of Both
an Audio Speaker and a Head Phone) .................194
Head Phone Does Not Sound ..............................195

AV-4Revision: 2004 November 2004 FX35/FX45Remote Controller Is Not Work .............................196
No CD·DVD Sound From All Speakers ................197
Removal and Installation for DVD Player .............198
REMOVAL .........................................................198INSTALLATION ..................................................199
Removal and Installation for DVD Display Unit .....199
REMOVAL ..........................................................199
INSTALLATION ..................................................200

AUDIO
AV-7
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
AUDIOPFP:28111
System DescriptionAKS00BMM
BASE SYSTEM
Refer to Owner's Manual for audio system operating instructions.
Power is supplied at all times

through 15A fuse (No. 32, located in the fuse and fusible link block)

to audio unit terminal 6

to A/C and AV switch terminal 1 and

to display control unit terminal 1 (with navigation system) or display unit terminal 1 (without navigation sys-
tem).
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to audio unit terminal 10

to A/C and AV switch terminal 2 and

to display control unit terminal 10 (with navigation system) or display unit terminal 2 (without navigation
system).
Ground is supplied through the case of the audio unit.
Ground is also supplied

to A/C and AV switch terminal 5

to display control unit terminal 3 and 13 (with navigation system)

to display terminal 1 (with navigation system)

to display unit terminal 6 and 15 (without navigation system)

through body ground M35, M45 and M85

to option connector for satellite radio receiver terminal 10

through body ground B210 and B203.
Audio unit, A/C and audio controller are connected by FPC (Flexible Print Circuit).
A/C and audio controller integrates A/C switches and audio switches.
When A/C and audio controller is pushed to audio switch, it sends audio signal to audio unit.
Then audio signals are supplied

through audio unit terminals 1, 2, 3, 4, 13, 14, 15, and 16

to terminals 1 and 2 of front door speaker LH and RH

to terminals 1 and 2 of rear door speaker LH and RH

to terminals 1 and 2 of instrument speaker LH and RH.
When one of audio steering wheel switch is pushed to volume up, seek up, or mode ON, resistance in steering
switch circuit changes depending on which button is pushed.
When one of audio steering wheel switch is pushed to volume down, seek down, or power ON, resistance in
audio steering wheel switch circuit changes depending on which button is pushed.
BOSE SYSTEM
Refer to Owner's Manual for audio system operating instructions.
Power is supplied at all times

through 15A fuse (No. 32, located in the fuse and fusible link block)

to audio unit terminal 6

to woofer terminal 1

to A/C and AV switch terminal 1 and

to display control unit terminal 1 (with navigation system) or display unit terminal 1 (without navigation sys-
tem),

through 20A fuse [No.17, located in the fuse block (J/B)]

to BOSE speaker amp. terminal 1.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to audio unit terminal 10

AV-8
AUDIO
Revision: 2004 November 2004 FX35/FX45

to A/C and AV switch terminal 2 and

to display control unit terminal 10 (with navigation system) or display unit terminal 2 (without navigation
system).
Ground is supplied through the case of the audio unit.
Ground is also supplied

to BOSE speaker amp. terminal 17

to woofer terminal 2

to option connector for satellite radio receiver terminal 10

through body ground B203 and B210,

to A/C and AV switch terminal 5

to display control unit terminal 3 and 13 (with navigation system)

to display terminal 1 (with navigation system)

to display unit terminal 6 and 15 (without navigation system)

through body ground M35, M45 and M85,
Audio unit, A/C and audio controller are connected by FPC (Flexible Print Circuit).
A/C and audio controller integrates A/C switches and audio switches.
When A/C and audio controller is pushed to audio switch, it send audio signal to audio unit.
Then audio signals are supplied

through audio unit terminals 1, 2, 3, 4, 13, 14, 15, and 16

to BOSE speaker amp. terminals 23, 24, 25, 26, 27, 28, 29, and 30.
Audio signals are amplified by the BOSE speaker amp.
The amplified audio signals are supplied

through BOSE speaker amp. terminals 2, 3, 4, 9,10,11,12, 13, 14, 15, 16, 18, 19 and 20

to terminals 1 and 2 of front door speaker LH and RH

to terminals 1 and 2 of rear door speaker LH and RH

to terminals 1 and 2 of tweeter LH and RH.

to terminals 1 and 2 of instrument speaker LH, RH, and CENTER,

to terminals 7 and 8 of woofer.
When one of audio steering wheel switch is pushed to volume up, seek up, or mode ON, resistance in audio
steering wheel switch circuit changes depending on which button is pushed.
When one of audio steering wheel switch is pushed to volume down, seek down, or power ON, resistance in
audio steering wheel switch circuit changes depending on which button is pushed.
SPEED SENSITIVE VOLUME SYSTEM
Volume level of this system gone up and down automatically in proportion to the vehicle speed. And the con-
trol level can be selected by the customer.

AV-32
AUDIO
Revision: 2004 November 2004 FX35/FX45
24 (L) 23 (B/W)Audio sound
signal rear RHInput ON
Receive audio
signalNo sound from
rear door speaker
RH.
26 (B/R) 25 (BR)Audio sound
signal rear LHInput ONNo sound from
rear door speaker
LH.
28 (LG) 27 (PU)Audio sound
signal front RHInput ON
Receive audio
signalNo sound from
front door
speaker RH or
instrument
speaker RH.
30 (W) 29 (B)Audio sound
signal front LHInput ONNo sound from
front door
speaker LH or
instrument
speaker LH.
31 (P) Ground Control signal Input ON – Approx. 12VBOSE speaker
amp. does not
work properly. Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference valueExample of
symptom
+–Igni-
tion
switchOperation
SKIA0177E
SKIA0177E

AUDIO
AV-33
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
Terminals and Reference Value for A/C and AV SwitchAKS00A2B
Terminal No.
(Wire color)
ItemSignal
input/
outputCondition
Vo l ta g eExample of
symptom
+–Igni-
tion
switchOperation
1 (W/L) GroundBattery power
supply Input OFF – Battery voltageSystem does not
work properly.
2 (LG/R) GroundACC power-
supplyInput ACC – Battery voltageSystem does not
work properly.
3 (R/L) GroundIllumination
signal Input OFFLighting switch is
ONApprox. 12VA/C and AV
switch illumina-
tion does not
come on when
lighting switch is
ON. Lighting switch is
OFFApprox. 0V
4 (R/Y) GroundIllumination
control signalOutput ONIllumination control
switch is operated
by lighting switch in
1st or 2nd position.Changes between approx.0V
and approx.12VA/C and AV
switch illumina-
tion does not
come on when
lighting switch is
ON.
5 (B) Ground Ground – ON – Approx. 0V –
6 (B/R) GroundCommunica-
tion signal (+)Input/
OutputON –System does not
work properly.
7–Shield
ground –– – – –
8 (W/R) GroundCommunica-
tion signal (–)Input/
OutputON –System does not
work properly.
12 (R/G) GroundRemote con-
troller AInput ONPress MODE switch. Approx. 0V
Steering wheel
audio controls
do not function. Press SEEK UP
switch.Approx. 1.7V
Press VOL UP
switch.Approx. 3.3V
Except for above Approx. 5V
13 (G/W) GroundRemote con-
troller BInput ONPress POWER
switch.Approx. 0V
Steering wheel
audio controls
do not function. Press SEEK DOWN
switch.Approx. 1.7V
Press VOL DOWN
switch.Approx. 3.3V
Except for above Approx. 5V
14 (B/Y) –Remote con-
troller ground–– – –Steering wheel
audio controls
do not function.
SKIA0175E
SKIA0176E

INTEGRATED DISPLAY SYSTEM
AV-55
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
INTEGRATED DISPLAY SYSTEMPFP:28090
System DescriptionAKS00BO5
A/C AND AV SWITCH SYSTEM
Refer to Owner′s Manual for A/C and AV switch operating instructions.
Using the A/C and AV switch at the center of the instrument panel, the controls of the following systems are
centralized:

Integrated display system (Drive computer, setting screen, etc.)

Auto A/C system

Audio system
PRECAUTION OF LCD MONITOR

In order to use LED for backlight of a display, by in car temperature, brightness may change. In low tem-
perature, the refreshing rate of the picture also becomes low because of the low response of the LCD
monitor. When passenger room becomes warm, however, the LCD recovers the normal display.

Backlight sometimes flickers or darkens according to the total consumption hours and the number of times
switched ON and OFF. In this case, display unit should be replaced. (Exchange only of backlight is impos-
sible.)
POWER SUPPLY AND GROUND
Power is supplied at all times

through 15A fuse (No. 32, located in fuse and fusible link box)

to display unit terminal 1, and

to A/C and AV switch terminal 1.
When ignition switch is in ACC or ON position, power is supplied

through 10A fuse [No. 6, located in fuse block (J/B)]

to display unit terminal 2, and

to A/C and AV switch terminal 2.
When ignition switch is in ON or START position, power is supplied

through 10A fuse [No. 12, located in fuse block (J/B)]

to display unit terminal 3.
Ground is supplied

to display unit terminals 6 and 15, and

to A/C and AV switch terminal 5

through body grounds M35, M45 and M85.