INFINITI FX35 2005 Service Manual

AT-308
REPAIR FOR COMPONENT PARTS
Revision: 2005 July 2005 FX
REPAIR FOR COMPONENT PARTSPFP:00000
Oil PumpACS0081M
COMPONENTS
DISASSEMBLY
1. Remove oil pump housing from oil pump cover.
2. Remove oil pump housing oil seal using a flat-bladed screw- driver.
CAUTION:
Be careful not to scratch oil pump housing.
1. O-ring 2. Oil pump cover 3. O-ring
4. Oil pump housing 5. Oil pump housing oil seal
SCIA5323E
SCIA6388E
SCIA2840E

REPAIR FOR COMPONENT PARTS AT-309
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
3. Remove O-ring from oil pump housing.
4. Remove O-ring from oil pump cover.
ASSEMBLY
1. Install O-ring to oil pump cover.
CAUTION:

Do not reuse O-ring.

Apply ATF to O-ring.
2. Install O-ring to oil pump housing. CAUTION:

Do not reuse O-ring.

Apply ATF to O-ring.
SCIA2841E
SCIA5230E
SCIA5230E
SCIA2841E

AT-310
REPAIR FOR COMPONENT PARTS
Revision: 2005 July 2005 FX
3. Using the drift, install oil pump housing oil seal to the oil pump
housing until it is flush.
CAUTION:

Do not reuse oil seal.

Apply ATF to oil seal.
4. Install oil pump housing to oil pump cover.
5. Tighten bolts to the specified torque in numerical order shown in the figure after temporarily tightening them.
SCIA5313E
: 9.0 N·m (0.92 kg-m, 80 in-lb.)
SCIA6388E

REPAIR FOR COMPONENT PARTS AT-311
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
Front Sun Gear, 3rd One-way ClutchACS0081N
COMPONENTS
DISASSEMBLY
1. Using a flat-bladed screwdriver, remove snap ring from front sun gear.
2. Remove 3rd one-way clutch from front sun gear.
1. Front sun gear 2. 3rd one-way clutch 3. Snap ring
SCIA3114E
SCIA3110E
S C I A 3 111 E

AT-312
REPAIR FOR COMPONENT PARTS
Revision: 2005 July 2005 FX
INSPECTION
3rd One-way Clutch

Check frictional surface for wear or damage.
CAUTION:
If necessary, replace the 3rd one-way clutch.
Front Sun Gear Snap Ring

Check for deformation, fatigue or damage.
CAUTION:
If necessary, replace the snap ring.
Front Sun Gear

Check for deformation, fatigue or damage.
CAUTION:
If necessary, replace the front sun gear.
ASSEMBLY
1. Install 3rd one-way clutch in front sun gear.
CAUTION:
Apply ATF to 3rd one-way clutch.
2. Using a flat-bladed screwdriver, install snap ring in front sun gear.
3. Check operation of 3rd one-way clutch.
a. Hold oil pump assembly and turn front sun gear.
b. Check 3rd one-way clutch for correct locking and unlocking directions.
CAUTION:
If not as shown in the figure, check installation direction of
3rd one-way clutch.
S C I A 3 111 E
SCIA3110E
SCIA3131E

REPAIR FOR COMPONENT PARTS AT-313
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
Front Carrier, Input Clutch, Rear Internal GearACS0081O
COMPONENTS
1. Seal ring 2. O-ring 3. Needle bearing
4. Bearing race 5. Front carrier assembly 6. Snap ring
7. Snap ring 8. Retaining plate 9. Driven plate
10. Input clutch drum 11. Drive plate 12. Rear internal gear
SCIA5426E

AT-314
REPAIR FOR COMPONENT PARTS
Revision: 2005 July 2005 FX
DISASSEMBLY
1. Compress snap ring using 2 flat-bladed screwdrivers.
2. Remove front carrier assembly and input clutch assembly from rear internal gear.
3. Remove front carrier assembly from input clutch assembly.
a. Remove bearing race from front carrier assembly.
b. Remove snap ring from front carrier assembly. CAUTION:
Do not expand snap ring excessively.
4. Disassemble input clutch assembly.
a. Remove O-ring and seal rings from input clutch assembly.
SCIA5339E
SCIA2847E
SCIA5476E
SCIA5235E

REPAIR FOR COMPONENT PARTS AT-315
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
b. Remove needle bearing from input clutch assembly.
c. Using a flat-bladed screwdriver, remove snap ring from input
clutch drum.
d. Remove drive plates, driven plates and retaining plate from input clutch drum.
INSPECTION
Front Carrier Snap Ring

Check for deformation, fatigue or damage.
CAUTION:
If necessary, replace the snap ring.
Input Clutch Snap Ring

Check for deformation, fatigue or damage.
CAUTION:
If necessary, replace the input clutch assembly.
Input Clutch Drum

Check for deformation, fatigue or damage or burns.
CAUTION:
If necessary, replace the input clutch assembly.
Input Clutch Drive Plates

Check facing for burns, cracks or damage.
CAUTION:
If necessary, replace the input clutch assembly.
Input Clutch Retaining Plates and Driven Plates

Check facing for burns, cracks or damage.
CAUTION:
If necessary, replace the input clutch assembly.
Front Carrier

Check for deformation, fatigue or damage.
CAUTION:
If necessary, replace the front carrier assembly.
Rear Internal Gear

Check for deformation, fatigue or damage.
CAUTION:
If necessary, replace the rear internal gear assembly.
SCIA2853E
SCIA2864E

AT-316
REPAIR FOR COMPONENT PARTS
Revision: 2005 July 2005 FX
ASSEMBLY
1. Install input clutch.
a. Install drive plates, driven plates and retaining plate in input clutch drum.
CAUTION:
Take care with order of plates.
b. Using a flat-bladed screwdriver, install snap ring in input clutch drum.
c. Install needle bearing in input clutch assembly. CAUTION:
Apply petroleum jelly to needle bearing.
d. Install O-ring and seal rings in input clutch assembly. CAUTION:

Do not reuse O-ring and seal rings.

Apply ATF to O-ring.

Apply petroleum jelly to seal rings.
2. Install front carrier assembly.
a. Install snap ring to front carrier assembly. CAUTION:
Do not expand snap ring excessively.
SCIA2864E
SCIA2853E
SCIA5235E
SCIA5476E

REPAIR FOR COMPONENT PARTS AT-317
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
b. Install bearing race in front carrier assembly.
CAUTION:
Apply petroleum jelly to bearing race.
c. Install front carrier assembly to input clutch assembly.
3. Compress snap ring using 2 flat-bladed screwdrivers.
4. Install front carrier assembly and input clutch assembly to rear internal gear.
SCIA2847E
SCIA5339E