Bulb INFINITI FX35 2005 Workshop Manual

VANITY MIRROR LAMP LT-151
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
VANITY MIRROR LAMPPFP:96400
Bulb ReplacementAKS007EC
1. Insert a thin screwdriver in the lens end and remove lens.
2. Remove bulb together with substrate.
3. Installation is the reverse order of removal. Vanity mirror lamp : 12V - 1.32W
PKIA7806E

LT-152
MAP LAMP
Revision: 2005 July 2005 FX
MAP LAMPPFP:26430
Bulb ReplacementAKS007ED
1. Remove lens using clip driver or suitable tool.
2. Remove bulb.
3. Installation is the reverse order of removal.
Removal and InstallationAKS007EE
REMOVAL
1. Insert a clip driver or suitable tool back of map lamp and pull down it to disengage pawl.
2. Pull down map lamp in direction shown by the arrow in the fig- ure.
3. Disconnect map lamp connector and remove map lamp.
INSTALLATION
Installation is the reverse order of removal. Map lamp : 12V - 8 W
PKIA2846E
PKIA2847E

PERSONAL LAMP LT-153
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
PERSONAL LAMPPFP:26415
Bulb ReplacementAKS007FT
1. Remove personal lamp. Refer to LT- 1 5 3 , "Removal and Installa-
tion" .
2. Remove screw from personal lamp.
3. Insert a screwdriver or similar tool and remove lens.
4. Remove bulb.
5. Installation is the reverse order of removal.
Removal and InstallationAKS007FU
REMOVAL
1. Use a clip driver or similar tool to press metal clip, and remove personal lamp.
2. Disconnect personal lamp connector.
INSTALLATION
Installation is the reverse order of removal. Personal lamp : 12V - 8W
SKIA5577E
SKIA5578E

LT-154
LUGGAGE ROOM LAMP
Revision: 2005 July 2005 FX
LUGGAGE ROOM LAMPPFP:26410
Bulb ReplacementAKS007FV
1. Remove luggage room lamp. Refer to LT- 1 5 4 , "Removal and
Installation" .
2. Remove screw from luggage room lamp.
3. Insert a suitable tool and remove lens.
4. Remove bulb.
5. Installation is the reverse order of removal.
Removal and InstallationAKS007FW
REMOVAL
1. Use a clip driver or similar tool to press metal clip, and remove luggage room lamp.
2. Disconnect luggage room lamp connector.
INSTALLATION
Installation is the reverse order of removal. Luggage room lamp : 12V - 8W
SKIA6197E
SKIA5579E

IGNITION KEY HOLE ILLUMINATION LT-155
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
IGNITION KEY HOLE ILLUMINATIONPFP:48476
Bulb Replacement, Removal and InstallationAKS007FR
1. Remove combination meter. Refer to DI-25, "Removal and
Installation of Combination Meter" in “DI” section.
2. Remove screw and remove NATS antenna amp.
3. Pull out ring and turn bulb socket to left to release lock.
4. Installation is the reverse order of removal. Ignition key hole illumination : 12V - 0.8W
SKIA5575E

LT-156
GLOVE BOX LAMP
Revision: 2005 July 2005 FX
GLOVE BOX LAMPPFP:68520
Bulb Replacement, Removal and InstallationAKS007FS
1. Remove instrument passenger lower panel. Refer to IP-18,
"INSTRUMENT PASSENGER LOWER PANEL" in “IP” section.
2. Turn bulb socket left to release lock and remove it.
3. Installation is the reverse order of removal. Glove box lamp : 12V - 1.4W
PKIB3636E

ASHTRAY ILLUMINATION LT-157
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
ASHTRAY ILLUMINATIONPFP:25860
Bulb Replacement and Removal and InstallationAKS007NZ
1. Remove A/T console finisher. Refer to IP-10, "INSTRUMENT
PANEL ASSEMBLY" in “IP” section.
2. Remove instrument ashtray and hazard switch. Refer to IP-16,
"A/T CONSOLE FINISHER" in “IP” section.
3. Use a screwdriver to undo ashtray finisher hooks.
4. Turn bulb socket on circuit board to left to undo lock. Remove bulb socket.
5. Installation is the reverse order of removal.
Ashtray and cigarette
lighter illumination : 12V - 1.4W
PKIA2850E

LT-158
CIGARETTE LIGHTER ILLUMINATION
Revision: 2005 July 2005 FX
CIGARETTE LIGHTER ILLUMINATIONPFP:25331
Bulb Replacement and Removal and InstallationAKS007O0
Refer to LT- 1 5 7 , "Bulb Replacement and Removal and Installation" in “ASHTRAY ILLUMINATION”.

INTERIOR ROOM LAMP LT-185
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
3. CHECK IGNITION KEY HOLE ILLUMINATION INPUT
1. Turn ignition switch OFF.
2. Check voltage between ignition key hole illumination harness connector M24 terminal 1 (R/B) and ground.
OK or NG
OK >> GO TO 4.
NG >> GO TO 6.
4. CHECK IGNITION KEY HOLE ILLUMINATION BULB
1. Disconnect ignition key hole illumination connector.
2. Check continuity between ignition key hole illumination terminals 1 and 2.
OK or NG
OK >> GO TO 5.
NG >> Replace ignition key hole illumination. Refer to LT- 1 5 5 ,
"Bulb Replacement, Removal and Installation" .
5. CHECK IGNITION KEY HOLE ILLUMINATION CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector M3 terminal 1 (PU) and ignition key hole illumination harness connector M24
terminal 2 (PU).
OK or NG
OK >> Replace BCM if ignition key hole illumination does not work after setting the connector again. Refer to BCS-16,
"Removal and Installation of BCM" .
NG >> Repair harness or connector.
6. CHECK IGNITION KEY HOLE ILLUMINATION CIRCUIT
1. Disconnect BCM connector and ignition key hole illumination connector.
2. Check continuity between BCM harness connector M4 terminal 41 (R/B) and ignition key hole illumination harness connector
M24 terminal 1 (R/B).
OK or NG
OK >> Replace BCM if ignition key hole illumination does not work after setting the connector again. Refer to BCS-16,
"Removal and Installation of BCM" .
NG >> Repair harness or connector. 1 (R/B) – Ground : Battery voltage.
PKIA5260E
1 – 2 : Continuity should exist.
PKIA7789E
1 (PU) – 2 (PU) : Continuity should exist.
PKIA7643E
41 (R/B) – 1 (R/B) : Continuity should exist.
PKIB3520E

INTERIOR ROOM LAMP LT-187
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
4. CHECK STEP LAMP CIRCUIT
1. Disconnect BCM connector and front door driver side step lamp connector.
2. Check continuity between BCM harness connector M4 terminal 41 (R/B) and front door driver side step lamp harness connector
D9 terminal 1 (R).
OK or NG
OK >> Replace BCM if step lamp does not work after setting the connector again. Refer to BCS-16, "
Removal and
Installation of BCM" .
NG >> Repair harness or connector.
All Interior Room Lamps Do Not OperateAKS007FJ
1. CHECK POWER SUPPLY CIRCUIT
1. All interior room lamps switch are OFF.
2. Turn ignition switch ON.
3. Check voltage between BCM harness connector M4 terminal 41 (R/B) and ground.
OK or NG
OK >> Repair harness or connector. In a case of making a short circuit, be sure to disconnect cable from the nega-
tive terminal repairing harness, and then reconnect.
NG >> Replace BCM. Refer to BCS-16, "
Removal and Installa-
tion of BCM" .
Bulb ReplacementAKS007FK
INTERIOR ROOM LAMP
1. Remove interior room lamp. Refer to LT- 1 8 8 , "Removal and
Installation" .
2. Insert a suitable tool and remove lens.
3. Remove bulb.
4. Installation is the reverse order of removal.
MAP LAMP
Refer to LT- 1 5 2 , "Bulb Replacement" in “MAPLAMP”.
PERSONAL LAMP
Refer to LT- 1 5 3 , "Bulb Replacement" in “PERSONAL LAMP”.
41 (R/B) – 1 (R) : Continuity should exist.
PKIB3523E
41 (R/B) – Ground : Battery voltage.
PKIB3524E
Interior room lamp :12V - 10W
PKIB3637E