power steering INFINITI FX35 2005 Service Manual

ABCDEFGHIJKMLQUICK REFERENCE INDEX AGENERAL INFORMATIONGIGeneral InformationBENGINEEMEngine MechanicalLUEngine Lubrication SystemCOEngine Cooling SystemECEngine Control SystemFLFuel SystemEXExhaust SystemACCAccelerator Control SystemCTRANSMISSION/
TRANSAXLEATAutomatic TransmissionDDRIVELINE/AXLETFTransferPRPropeller ShaftFFDFront Final DriveRFDRear Final DriveFAXFront AxleRAXRear AxleESUSPENSIONFSUFront SuspensionRSURear SuspensionWTRoad Wheels & TiresFBRAKESBRBrake SystemPBParking Brake SystemBRCBrake Control SystemGSTEERINGPSPower Steering SystemHRESTRAINTSSBSeat BeltsSRSSupplemental Restraint System
(SRS)IBODYBLBody, Lock & Security SystemGWGlasses, Window System & Mir-
rorsRFRoofEIExterior & InteriorIPInstrument PanelSESeatJAIR CONDITIONERATCAutomatic Air ConditionerKELECTRICALSCStarting & Charging SystemLTLighting SystemDIDriver Information SystemWWWiper, Washer & HornBCSBody Control SystemLANLAN SystemAVAudio Visual, Navigation & Tele-
phone SystemACSAuto Cruise Control SystemPGPower Supply, Ground & Circuit Ele-
mentsLMAINTENANCEMAMaintenanceMINDEXIDXAlphabetical IndexEdition: August 2004
Revision: July 2005

QUICK REFERENCE CHART M35/M45
QUICK REFERENCE CHART M35/M45PFP:00000
ENGINE TUNE-UP DATA (VQ35DE)ELS0003W
Engine modelVQ35DE
Firing order1-2-3-4-5-6
Idle speed
A/T (In “P” or “N” position)rpm
650 ± 50
Ignition timing (BTDC at idle speed)
A/T (In “P” or “N” position)15° ± 5°
CO% at idle 0.7 - 9.9 % and engine runs smoothly
Drive BeltDeflection adjustment Unit: mm (in) Tension adjustment Unit: N (kg, lb)
Used belt
New beltUsed belt
New belt
Limit After adjustment Limit After adjustment
Alternator and power
steering oil pump belt7 (0.28)4 - 5
(0.16 - 0.20)3.5 - 4.5
(0.138 - 0.177)294 (30, 66)730 - 818
(74.5 - 83.5,
164 - 184)838 - 926
(85.5 - 94.5,
188 - 208)
A/C compresor belt 12 (0.47)9 - 10
(0.35 - 0.39)8 - 9
(0.31 - 0.35)196 (20, 44)348 - 436
(35.5 - 44.5,
78 - 98)470 - 559
( 4 8 - 5 7 ,
106 - 126)
Applied pushing force 98N (10kg, 22lb) —
Radiator cap relief pressure
kPa (kg/cm
2 , psi)
Standard 78 - 98 (0.8 - 1.0, 11 - 14)
Limit 59 (0.6, 9)
Cooling system leakage testing pres-
surekPa (kg/cm
2 , psi)157 (1.6, 23)
Compression pressure
kPa (kg/cm
2 , psi)/rpm
Standard 1,275 (13.0, 185) /300
Minimum 981 (10.0, 142) /300
Spark plug Standard type PLFR5A-11
Hot type PLFR4A-11
Cold type PLFR6A-11
2005

QUICK REFERENCE CHART M35/M45
REAR WHEEL ALIGNMENT (Unladen*)
ELS0003Y
* : Fuel, engine coolant and engine oil full. Spare tire, jack, hand tools and mats in designated positions.
BRAKEELS0003Z
* : Under force of 490 N (50 kg, 110 lb) with engine running.
REFILL CAPACITIESELS00040
Camber
Degree minute (Decimal degree)Minimum – 1° 18′ (– 1.30°)
Nominal – 0° 48′ (– 0.80°)
Maximum – 0° 18′ (– 0.30°)
Total toe-inDistance ( A – B ) Minimum 2.4 mm (0.094 in)
Nominal 4.7 mm (0.185 in)
Maximum 7.0 mm (0.276 in)
Angle (left plus right )
Degree minute (Degree)Minimum 0° 05′ (0.08°)
Nominal 0° 10′ (0.17°)
Maximum 0° 15′ (0.25°)
Front brake Pad wear limit 2.0 mm (0.079 in)
Rotor repair limit 26.0 mm (1.024 in)
Rear brake Pad wear limit 2.0 mm (0.079 in)
Rotor repair limit 14.0 mm (0.551 in)
Pedal free height 161.5 - 171.5 mm (6.358 - 6.752 in)
Pedal depressed height* More than 80 mm (3.15 in)
UNITLiter US measure
Fuel tank90 23 - 3/4 gal
Coolant ( With reservoir tank )VQ35DE 8.6 9 - 1/8 qt
VK45DE 10.0 10 - 5/8 qt
Engine(VQ35DE)Drain and refill
With oil filter change 4.7 5 qt
Without oil filter change 4.4 4 - 5/8 qt
Dry engine (Overhaul) 5.4 5 - 3/4 qt
Engine(VK45DE)Drain and refill
With oil filter change 6.4 6 - 3/4 qt
Without oil filter change 5.8 6 - 1/8 qt
Dry engine (Overhaul) 7.2 7 - 5/8 qt
Transmission A/T 10.3 10 - 7/8 qt
Transfer1.25 2 - 5/8 pt
Differential carrierFront 0.65 1 - 3/8 pt
Rear 1.4 3 pt
Power steering system 1.0 1 - 1/8 qt
Air conditioning systemCompressor oil 0.18 6.0 fl oz
Refrigerant 0.55 kg 1.21 lb
2005

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION ACS-31
[ICC]
C
D E
F
G H
I
J
L
M A
B
ACS
Revision: 2005 July 2005 FX
6. Touch any of “WORK SUPPORT”, “SELF-DIAG RESULTS”,
“DATA MONITOR”, “CAN DIAG SUPPORT MNTR”, “ACTIVE
TEST” and “ECU PART NUMBER” on selection screen.
WORK SUPPORT
Work Item
Cause of Auto-Cancel
1. Touch “WORK SUPPORT” on the “SELECT DIAG MODE” screen. Refer to ACS-30, "
CONSULT-II BASIC OPERATION" .
2. Touch “CAUSE OF AUTO-CANCEL” on the “SELECT WORK ITEM” screen.
3. Cause of automatic cancellation screen will be shown. CAUTION:
Last five cancel (system cancel) causes are displayed.
Display Item List
Laser Beam Adjust
For details, refer to ACS-12, "LASER BEAM AIMING ADJUSTMENT" .
PKIA8867E
Operation Function
CAUSE OF AUTO-CANCEL Indicates causes of automatic cancellation of the ICC system.
LASER BEAM ADJUST Outputs laser beam, calculates dislocation of the beam, and indicates adjustment direction.
SKIA6191E
Cause of cancellation Description
OPERATING WIPER Windshield wipers were operated at HI or LO speed operation.
OPERATING ABS ABS function was operated.
OPERATING TCS TCS function was operated.
OPERATING VDC VDC function was operated.
OPE SW VOLT CIRC Outside the standard control switch input voltage was detected.
ECM CIRCUIT ECM did not permit ICC operation.
LASER SUN BEAM Intense light such as sunlight entered ICC sensor light sensing part.
LASER TEMP Temperature around ICC sensor became low.
OP SW DOUBLE TOUCH ICC steering switches were pressed at the same time.
WHL SPD ELEC NOISE Wheel speed sensor signal caught electromagnetic noise.
VDC/TCS OFF SW VDC OFF switch was pressed.
WHEEL SPD UNMATCH Wheel speed became different from AT vehicle speed.
TIRE SLIP Wheel slipped.
PKB SW ON Parking brake is applied.
IGN LOW VOLT Power supply voltage became low.
SNOW MODE SW Snow mode switch was pressed.
NO RECORD —

ACS-38
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: 2005 July 2005 FX
SELF-DIAGNOSIS BY ICC SYSTEM DISPLAY WILL NOT RUN
Possible Irregular Condition
1. CHECK FUSES
Check that any of the fuses is blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse.
2. CHECK ICC SYSTEM DISPLAY
1. Turn ignition switch ON.
2. Check if all displays illuminate.
Do all displays illuminate?
YES >> GO TO 3.
NO >> GO TO 6.
PKIB4144E
Open or short lines Symptoms Malfunction causes
ICC unit power supply malfunction No voltage supply from ignition switch Fuse blown
Harness open
Harness shorted
Ground cable not connected Harness open Harness shorted
ICC steering switch malfunction No signal transmitted Harness open Harness shorted
Spiral cable open
Spiral cable shorted
Switch or ECM malfunction
CAN communication system malfunction Signal not transmitted Harness open Harness shorted
CAN communication outside the standard.
Combination meter system malfunction Indication not possible Indicator display malfunction ICC system display segments disappear.
ICC unit malfunction ICC unit internal malfunction.
Unit Power source Fuse No.
ICC unit Ignition switch (ON) 12
Battery 35

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS ACS-41
[ICC]
C
D E
F
G H
I
J
L
M A
B
ACS
Revision: 2005 July 2005 FX
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMSPFP:00000
Diagnostic Trouble Code (DTC) ChartAKS006YW
×: Applicable
DTC No. CONSULT-II
screen terms ICC
system
warning lamp Fail-safe
Malfunctions detected where... Refer-
ence
page
Vehicle-
to-
vehicle
distance
control mode Conven-
tional
(fixed
speed) cruise
control
mode Brake
assist
(with
preview
function)
11 CONTROL UNIT ××××

ICC unit internal malfunctionACS-42
20 CAN COMM CIRCUIT ××××
ICC unit detected CAN communi-
cation malfunction. ACS-43
31 POWER SUPPLY CIR
××××
ICC unit power supply voltage is
excessively low (less than 8V). ACS-43
34 POWER SUPPLY CIR2
××××
ICC unit power supply voltage is
excessively high (more than 19V). ACS-43
41 VHCL SPEED SE CIRC
××××

Wheel sensor malfunction.

ABS actuator and electric unit (
control unit) malfunction

AT vehicle speed sensor malfunc-
tion

TCM malfunction ACS-44
43 ABS/TCS/VDC CIRC
××××
VDC/TCS/ABS system malfunc-
tion ACS-45
45 BRAKE SW/ STOP L SW
××××

Brake and stop lamp switch har-
ness is open or shorted.

Brake and stop lamp switch is ON
or stuck to OFF.

Brake and stop lamp switch is
stuck to ON. ACS-45
46 OPERATION SW CIRC
×××

ICC steering switch harness or
spiral cable is open or shorted.

ICC steering switch malfunction ACS-47
61 PRESS SEN CIRCUIT
×× ×

Brake pressure sensor harness is
open or shorted.

Brake pressure sensor malfunc-
tion

Brake pressure sensor input cir-
cuit malfunction ACS-48
62
BOOSTER SOL/V
CIRCUIT ×× ×

Solenoid harness is open or
shorted.

Solenoid is open.

Solenoid drive circuit malfunction ACS-50
63 RELEASE SW CIRCUIT
××××

Release switch harness is open or
shorted.

Release switch malfunction

Release switch input circuit mal-
function ACS-51
65 PRESSURE CONTROL
×× ×
Booster malfunctionACS-52
74 LASER BEAM OFF CNTR ×× ×
Laser beam of ICC sensor is off
the aiming point. ACS-53

PRECAUTIONS ATC-5
C
D E
F
G H
I
K L
M A
B
AT C
Revision: 2005 July 2005 FX
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AJS001XF
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions Necessary for Steering Wheel Rotation After Battery DisconnectAJS001XG
NOTE:

This Procedure is applied only to models with Intelligent Key system and NVIS/IVIS (NISSAN/INFINITI
VEHICLE IMMOBILIZER SYSTEM - NATS).

Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″ LOCK ″ position.

Always use CONSULT-II to perform self-diagnosis as a part of each function inspection after finishing
work. If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NVIS/IVIS, an electrically controlled steering lock
mechanism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC ″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be rotated.
4. Perform the necessary repair operation.
5. When the repair work is completed, return the ignition switch to the ″LOCK ″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-II.

ATC-154
REFRIGERANT LINES
Revision: 2005 July 2005 FX

When recharging refrigerant, check for leaks.
Removal and Installation of Liquid TankAJS0015Y
REMOVAL
1. Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2. Remove front grille. Refer to EI-22, "
FRONT GRILLE" .
3. Clean liquid tank and its surrounding area, and remove dirt and rust from liquid tank. CAUTION:
Be sure to clean carefully.
4. Remove mounting bolts from liquid tank and power steering oil cooler.
5. Lift liquid tank bracket upward. Remove bracket from protruding part of condenser.
6. Slide liquid tank upward, and then remove liquid tank.
INSTALLATION
Install liquid tank, and then install liquid tank bracket on condenser.
CAUTION:

Make sure liquid tank bracket is securely installed at protru-
sion of condenser. (Make sure liquid tank bracket does not
move to a position below center of liquid tank.)

Replace O-rings of A/C piping with new ones, and then
apply compressor oil to it when installing it.

When recharging refrigerant, check for leaks. Low-pressure pipe 1 bracket and low-pressure flexible hose bracket mounting bolts
Tightening torque : 5.5 N·m (0.56 kg-m, 49 in-lb)
RJIA2074E
RJIA0672E
RJIA0673E

AV-1
AUDIO VISUAL, NAVIGATION & TELEPHONE SYS- TEM
K ELECTRICAL
CONTENTS
C
D E
F
G H
I
J
L
M
SECTION AV
A
B
AV
Revision: 2005 July 2005 FX
AUDIO VISUAL, NAVIGATION & TELEPHONE SYSTEM
PRECAUTIONS .......................................................... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 5
PREPARATION ...................................................... ..... 6
Commercial Service Tools ................................... ..... 6
AUDIO .................................................................... ..... 7
Component Parts and Harness Connector Location ..... 7
System Description ............................................. ..... 8
BASE SYSTEM ................................................ ..... 8
BOSE SYSTEM ............................................... ..... 8
SPEED SENSITIVE VOLUME SYSTEM ......... ..... 9
Schematic - Base System - ................................. ... 10
Wiring Diagram - AUDIO - / Base System .......... .... 11
Schematic - BOSE System - With Navigation Sys-
tem ...................................................................... ... 16
Wiring Diagram – AUDIO – / BOSE System With
Navigation System .............................................. ... 17
Schematic - BOSE System - Without Navigation
System ................................................................ ... 25
Wiring Diagram – AUDIO – / BOSE System Without
Navigation System .............................................. ... 26
Terminals and Reference Value for Audio Unit .... ... 33
Terminals and Reference Value for BOSE Speaker
Amp. .................................................................... ... 34
Terminals and Reference Value for A/C and AV
Switch .................................................................. ... 36
Terminals and Reference Value for Woofer ......... ... 37
A/C and AV Switch Self-Diagnosis Function ....... ... 37
STARTING THE SELF-DIAGNOSIS MODE .... ... 37
EXITING THE SELF-DIAGNOSIS MODE ........ ... 37
DIAGNOSIS FUNCTION .................................. ... 37
Trouble Diagnosis ............................................... ... 38
MALFUNCTION WITH RADIO, TAPE AND CD ... 38
FOR RADIO ONLY ........................................... ... 39
FOR CASSETTE PLAYER ONLY .................... ... 39
FOR CD ONLY ................................................. ... 39
Noise Inspection .................................................. ... 40
TYPE OF NOISE AND POSSIBLE CAUSE ..... ... 40
Power Supply Circuit Inspection ......................... ... 41 Audio Steering Wheel Switch Inspection .............
... 42
A/C and AV Switch Inspection ............................. ... 44
BOSE Speaker Amp. Inspection ......................... ... 44
Vehicle Speed Signal Inspection ......................... ... 45
Locking CD Auto-Changer Mechanism ............... ... 46
DAMPER LOCK PROCEDURE ....................... ... 46
Removal and Installation of Audio Unit ................ ... 47
REMOVAL ........................................................ ... 47
INSTALLATION ................................................ ... 47
Disassembly and Assembly for Audio Unit .......... ... 47
DISASSEMBLY ................................................ ... 47
ASSEMBLY ...................................................... ... 47
Removal and Installation for A/C and AV Switch . ... 48
REMOVAL ........................................................ ... 48
INSTALLATION ................................................ ... 48
Removal and Installation for Front Door Speaker ... 48
REMOVAL ........................................................ ... 48
INSTALLATION ................................................ ... 48
Removal and Installation for Rear Door Speaker ... 49 REMOVAL ........................................................ ... 49
INSTALLATION ................................................ ... 49
Removal and Installation for Instrument Speaker ... 49 REMOVAL ........................................................ ... 49
INSTALLATION ................................................ ... 49
Removal and Installation for Tweeter .................. ... 49
REMOVAL ........................................................ ... 49
INSTALLATION ................................................ ... 49
Removal and Installation for Woofer (BOSE Sys-
tem) ..................................................................... ... 50
REMOVAL ........................................................ ... 50
INSTALLATION ................................................ ... 50
Removal and Installation for BOSE Speaker Amp. ... 50
REMOVAL ........................................................ ... 50
INSTALLATION ................................................ ... 50
AUDIO ANTENNA ................................................. ... 51
System Description .............................................. ... 51
Wiring Diagram — M/ANT — .............................. ... 52
Terminals and Reference Value for Audio Unit .... ... 53
Antenna Amp. Inspection .................................... ... 53
Location of Antenna ............................................. ... 54

AV-2Revision: 2005 July 2005 FX
Window Antenna Repair ......................................
... 54
CHECK ELEMENT ........................................... ... 54
Removal and Installation of Roof Antenna .......... ... 56
REMOVAL ........................................................ ... 56
INSTALLATION ................................................. ... 56
INTEGRATED DISPLAY SYSTEM ......................... ... 57
System Description .............................................. ... 57
A/C AND AV SWITCH SYSTEM ....................... ... 57
PRECAUTION OF LCD MONITOR .................. ... 57
POWER SUPPLY AND GROUND .................... ... 57
DRIVE COMPUTER ......................................... ... 58
E/M SWITCH .................................................... ... 59
SETTING SCREEN .......................................... ... 60
WARNING INDICATIONS ................................ ... 61
AV COMMUNICATION LINE ............................ ... 61
CAN Communication System Description ........... ... 61
CAN Communication Unit .................................... ... 61
Component Parts and Harness Connector Location ... 61
Schematic ............................................................ ... 62
Wiring Diagram — INF/D — ................................ ... 63
Schematic ............................................................ ... 68
Wiring Diagram — COMM — .............................. ... 69
Terminals and Reference Value for Display Unit . ... 72
Terminals and Reference Value for A/C and AV
Switch .................................................................. ... 73
On Board Self-Diagnosis Function ...................... ... 74
DESCRIPTION ................................................. ... 74
DIAGNOSIS ITEM ............................................ ... 74
Self-Diagnosis Mode ........................................... ... 74
OPERATION PROCEDURES .......................... ... 74
NETWORK CHECK .......................................... ... 75
PARTS CHECK ................................................ ... 75
HVAC DETAIL SCREEN ................................... ... 76
VERSION CHECK ............................................ ... 76
CAN DIAG MNTR (CAN DIAG MONITOR) ...... ... 76
A/C and AV Switch Self-Diagnosis Function ........ ... 77
STARTING THE SELF-DIAGNOSIS MODE ..... ... 77
EXITING THE SELF-DIAGNOSIS MODE ........ ... 77
DIAGNOSIS FUNCTION .................................. ... 77
Trouble Diagnosis Chart by Symptom ................. ... 78
Power Supply and Ground Circuit Check for Display
Unit ...................................................................... ... 79
Power Supply and Ground Circuit Check for A/C and
AV Switch ............................................................. ... 80
Vehicle Speed Signal Inspection ......................... ... 80
Illumination Signal Inspection .............................. ... 81
Ignition Signal Inspection ..................................... ... 82
Audio Communication Line Inspection ................ ... 82
AV Communication Line Inspection ..................... ... 84
CAN Communication Line Inspection .................. ... 85
Audio Steering Wheel Switch Inspection ............. ... 86
Removal and Installation of Display ..................... ... 86
REMOVAL ........................................................ ... 86
INSTALLATION ................................................. ... 86
Removal and Installation of A/C and AV Switch .. ... 86
NAVIGATION SYSTEM .......................................... ... 87
System Description .............................................. ... 87
TRAVEL DISTANCE ......................................... ... 87
TRAVEL DIRECTION ....................................... ... 87 MAP-MATCHING ..............................................
... 87
GPS (GLOBAL POSITIONING SYSTEM) ........ ... 88
COMPONENT DESCRIPTION ......................... ... 89
BIRDVIEW™ ..................................................... ... 89
MAP DISPLAY .................................................. ... 90
FUNCTION OF CENTER SWITCH .................. ... 91
“VIEW” MODE ................................................... ... 97
“HEADING” MODE ........................................... ... 98
“NEARBY DISPLAY ICONS” MODE ................. ... 98
“SAVE CURRENT LOCATION” MODE ............. ... 98
“ADJUST CURRENT LOCATION” MODE ........ ... 98
“AUTO RE-ROUTE” MODE .............................. ... 99
“AVOID AREA SETTING” MODE ..................... ... 99
“CLEAR MEMORY” MODE ............................... ... 99
“EDIT ADDRESS BOOK” MODE ...................... .100
“GPS INFORMATION” MODE .......................... .100
“QUICK STOP CUSTOMER SETTING” MODE .100
“SET AVERAGE SPEED” MODE ..................... .100
“TRACKING” MODE ......................................... .101
GUIDANCE VOLUME ....................................... .101
DISPLAY WITH PUSHED “TRIP” BUTTON ...... .101
TRIP 1 OR TRIP 2 ............................................ .102
FUEL ECONOMY ............................................. .102
MAINTENANCE ................................................ .102
ENGINE OIL OR TIRE ROTATION ................... .102
TIRE PRESSURE ............................................. .103
WARNING INDICATIONS ................................. .103
CAN Communication System Description ........... .104
CAN Communication Unit .................................... .104
Component Parts Location and Harness Connector
Location ............................................................... .104
Schematic—NAVI— ............................................. .105
Wiring Diagram —NAVI— .................................... .106
Schematic — COMM — ....................................... .113
Wiring Diagram — COMM — ............................... .114
Terminals and Reference Value for NAVI Control
Unit ....................................................................... .119
Terminals and Reference Value for Display Control
Unit ....................................................................... .121
Terminals and Reference Value for Display ......... .125
Terminals and Reference Value for A/C and AV
Switch .................................................................. .127
On Board Self-Diagnosis Function ....................... .128
DESCRIPTION ................................................. .128
DIAGNOSIS ITEM ............................................ .128
Self-Diagnosis Mode (DCU) ................................. .129
OPERATION PROCEDURE ............................. .129
SELF–DIAGNOSIS RESULT ............................ .130
Self-Diagnosis Mode (NAVI) ................................ .131
OPERATION PROCEDURE ............................. .131
SELF–DIAGNOSIS RESULT ............................ .132
Confirmation/Adjustment Mode ............................ .133
OPERATION PROCEDURE ............................. .133
DISPLAY DIAGNOSIS ...................................... .134
VEHICLE SIGNALS .......................................... .134
AUTO CLIMATE CONTROL ............................. .135
NAVIGATION .................................................... .135
DISPLAY DIAGNOSIS ...................................... .135
VEHICLE SIGNALS .......................................... .136