ECO mode INFINITI QX30 2017 User Guide

Activating/deactivating the surround lighting
and exterior lighting delayed switch-off:
If you have activated the Surround lighting
function and the light switch is set to <AUTO>,
the following functions are activated when it is
dark:
•Surround lighting: the exterior lighting re-
mains lit for 40 seconds after unlocking with
the key. If you start the engine, the surround
lighting is switched off and automatic head-
light mode is activated .
•Exterior lighting delayed switch-off: the ex-
terior lighting remains lit for 60 seconds
after the engine is switched off. If you close
all the doors and the lift gate, the exterior
lighting goes off after 15 seconds.
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press <OK> to confirm.
4. Press the
orbutton to select
the [Surround Lighting] function.5. Press the <OK> button to save the setting.
When the [Surround Lighting] function is
activated, the light cone and the area around
the vehicle are displayed in orange in the
vehicle information display
6. Press the <OK> button to confirm the setting.
Deactivating delayed switch-off of the exterior
lighting temporarily:
1. Before leaving the vehicle, switci the igni-
tion switch to the OFF position.
2. Switch the ignition switch to the ON posi-
tion.
The exterior lighting delayed switch-off is
deactivated.
Delayed switch-off of the exterior lighting is
reactivated the next time you start the engine.
Depending on your vehicle’s equipment, when
the surround lighting and delayed switch-off
exterior lighting are on, the following light up:•Side lights
•Fog lights
•Low beam headlights
•Daytime driving lights
•Surround lighting in the exterior mirrorsActivating/deactivating the interior lighting
delay
:
If you activate the [Interior Lighting Delay] func-
tion, the interior lighting remains on for 20
seconds after you remove the key from the
ignition lock.
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press <OK> to confirm.
4. Press the
orbutton to select
the [Interior Lighting Delay] function. If the
[Interior lighting delayed switch-off] function
has been switched on, the vehicle interior is
displayed in orange in the vehicle informa-
tion display
5. Press the <OK> button to save the setting.
Instruments and controls2-27

Vehicle
Message Possible causes/consequences and solutions
[Depress Brake to Start
Engine](DCT models only). You have attempted to start the engine with the transmission in position N (Neutral) without depressing the brake
pedal.
Depress the brake pedal.
[To Deselect P or N, Depress
Brake and Start Engine]You have attempted to shift the shift lever to position R (Reverse) or D (Drive) without starting the engine.
Start the engine and depress the brake pedal.
NOTE•It is only possible to move the shift lever from position P (Park) to the desired position if you depress the brake pedal. Only then can
the parking lock be deactivated.
•At transmission fluid temperatures below -5oF (-20oC) you can only shift out of position P (Park) into another transmission position
when the engine is running.
[Apply Brake to Shift From
’P’]You have attempted to shift the shift lever to position R (Reverse), N (Neutral) or D (Drive) without depressing the brake pedal.
Depress the brake pedal.
[Risk of Rolling Transmission
Not in P]The driver’s door is open/not fully closed and the shift lever is in position R (Reverse), N (Neutral) or D (Drive).
A warning tone also sounds
WARNING
The vehicle may roll away.
There is a risk of an accident.
1. Press the P (Park) button.
2. Secure the vehicle against rolling away.
3. Close the driver’s door fully.
[Service Required Do Not
Shift Gears Visit Dealer]You cannot change the transmission position due to a malfunction.
A warning tone also sounds.
If transmission position D (Drive) is selected, Drive to an INFINITI retailer without shifting the transmission from position D (Drive).
If transmission position R (Reverse), N (Neutral) or P (Park), secure the vehicle against rolling away. It is recommended you consult an
INFINITI retailer.
2-52Instruments and controls

To deactivate the de-icer:
•Press thebutton. The indicator lamp
in thebutton turns off. The previous
settings are reactivated. Air-recirculation
mode remains deactivated.
or
•Automatic climate control: press the<AUTO>
button. The indicator lamp in the
button turns off. Airflow and air distribution
are set to automatic mode.
or
•Air-conditioning system or automatic cli-
mate control: adjust the temperature control
(seeHeater and air conditionerin the4.
Display screen, heater and air conditioner,
and audio systemDisplay screen, heater and
air conditioner, and audio systemsection).
HEADLIGHT SWITCH
1Left-hand parking lights
2Right-hand parking lights
3Side lights and license plate
lighting
4<AUTO>Automatic headlight mode, con-
trolled by the light sensor
5Low beam/high beam headlights
6Rear fog light
7Front fog lights (if equipped)
8Headlight aiming control (halogen head-
lights only)
INFINITI recommends that you consult the local
regulations concerning the use of lights.If you hear a warning tone when you leave the
vehicle, the side lights may still be switched on.
Turn the light switch to<AUTO>.
The exterior lighting (except the side lights/
parking lights) switches off automatically if you:
•Remove the key from the ignition switch (if
equipped).
•Open the driver’s door with the ignition
switch in the OFF position.
CAUTION
Use the headlights with the engine running to
avoid discharging the vehicle battery.
NIC2619LED headlightsNIC2697Halogen headlights
HEADLIGHT AND TURN SIGNAL SWITCHES
2-62Instruments and controls

Active light function
The active light function is a system that moves
the headlights according to the steering move-
ments of the front wheels. In this way relevant
areas remain illuminated while you are driving.
This helps you to recognize pedestrians, cy-
clists and animals. It is active when the lights
are switched on.
Cornering light function
The cornering light function improves the illu-
mination of the road over a wide angle in the
direction you are turning, enabling better vis-
ibility in tight bends, for example. It can only be
activated when the low-beam headlights are
switched on. It is active if you are driving at
speeds below 25 MPH (40 km/h) and switch on
the turn signal or turn the steering wheel.
The cornering light function may remain lit for a
short time, but is automatically switched off
after no longer than three minutes.
Freeway mode
Freeway mode adjusts the light beam to reduce
the amount of light that shines on the opposite
lane of the freeway, and oncoming traffic.
Freeway mode is active if you are driving at a
speed above 68 MPH (110 km/h) and do not
make any large steering movements for at least
3300 ft (1000 m) or if you are driving at a speed
above 81 MPH (130 km/h).
It is not active if you are driving at speeds below
50 MPH (80 km/h) following activation.
NSD593NSD592NSD594
Instruments and controls2-65

If the side window opens again slightly:
1. Immediately pull the corresponding switch
on the door control panel until the side
window is completely closed.
2. Hold the switch for an additional second.
3. If the corresponding side window remains
closed after the button has been released,
the side window has been reset correctly. If
this is not the case, repeat the steps above
again.
If the power window automatic function does
not operate properly after performing the pro-
cedure above, have your vehicle checked. It is
recommended you visit an INFINITI retailer for
this service.
1Close
2Open
CAUTION
•Do not place heavy objects on the glass roof
or surrounding area.
•Do not hang from the sunshade or hang any
objects from it. It may cause damage or de-
formation to the sunshade.
•Close the sunshade when you leave the
vehicle for extended periods of time to pre-
vent the inside of the vehicle from reaching
high temperatures.
SUNSHADE OPERATION
The sunshade operates only when the ignition
switch is in the ON position.
WARNING
To avoid personal injury, keep your hands, fin-
gers and head away from the sunshade arm,
the arm rail and sunshade inlet port.
NOTE
The following notes cover situations where
strong sun shining on the roof of the vehicle
causes the area around the sunshade motor to
reach high temperatures:
•If the temperature of the sunshade motor
reaches a value between 185oF (85oC) and
212oF (100oC), “restricted mode” is enabled,
and the sunshade will only be allowed to
CLOSE.
•If the temperature of the sunshade motor
exceeds 212oF (100oC), the sunshade will
not operate.
NIC2646
FIXED GLASS ROOF (IF EQUIPPED)
2-74Instruments and controls

The HomeLink® Universal Transceiver, inte-
grated in the vehicle’s inside rear view mirror,
provides a convenient way to consolidate the
functions of up to three individual hand-held
transmitters into one built-in device.
HomeLink® Universal Transceiver:
•Will operate most Radio Frequency (RF)
devices such as garage doors, gates, home
and office lighting, entry door locks and
security systems.
•Is powered by your vehicle’s battery. No
separate batteries are required. If the vehi-
cle’s battery is discharged or is discon-
nected, HomeLink® will retain all program-
ming.
When the HomeLink® Universal Transceiver is
programmed, retain the original transmitter for
future programming procedures (Example: new
vehicle purchases). Upon sale of the vehicle, the
programmed HomeLink® Universal Transceiver
buttons should be erased for security purposes.
For additional information, refer toProgram-
ming HomeLink®later in this section.
WARNING
•Do not use the HomeLink® Universal Trans-
ceiver with any garage door opener that
lacks safety stop and reverse features as
required by federal safety standards.
(These standards became effective for
opener models manufactured after April 1,
1982). A garage door opener which cannot
detect an object in the path of a closing
garage door and then automatically stop
and reverse, does not meet current federal
safety standards. Using a garage door
opener without these features increases the
risk of serious injury or death.
•During the programming procedure your
garage door or security gate will open and
close (if the transmitter is within range).
Make sure that people or objects are clear of
the garage door, gate, etc. that you are pro-
gramming.
•Your vehicle’s engine should be turned off
while programming the HomeLink® Univer-
sal Transceiver.NOTE
Certain garage door drives are incompatible
with the integrated garage door opener. If you
have difficulty programing the integrated ga-
rage door opener, it is recommended you contact
your INFINITI retailer.
PROGRAMMING HOMELINK®
If you have any questions or are having diffi-
culty programming your HomeLink® buttons,
refer to the HomeLink® web site at:
www.homelink.com or call 1-800-355-3515.
HOMELINK® UNIVERSAL TRANSCEIVER (IF
EQUIPPED)
2-86Instruments and controls

1. Turn the ignition key to the ON position.
2. Press and hold one of buttons
2to4on
the HomeLink®.
HomeLink® is now in programing mode.
After a short time, indicator lamp
1lights
up yellow.
Indicator lamp
1lights up yellow as soon
as button
2,3or4is programed for the
first time. If the selected button has already
been programed, indicator lamp
1will only
light up yellow after ten seconds have elapsed.
3. Release button2,3or4. Indicator lamp
1flashes yellow.
4. Position the end of your hand-held trans-
mitter
52–8 inches (5–20 cm) away from
the HomeLink® surface, keeping the
HomeLink® indicator light
1in view.5. Press and hold button
6on the hand held
transmitter until indicator lamp
1lights up
green. When indicator lamp
1: lights up
green: programing is finished.
When indicator lamp
1flashes green: pro-
graming was successful. The next step is to
synchronize the rolling code.
6. Release button
6on the hand held trans-
mitter
5for the garage door drive system.
If indicator lamp
1lights up red: repeat the
programing procedure for the corresponding
button on the rear-view mirror. When doing
so, vary the distance between the hand held
transmitter
5and the rear-view mirror.
The required distance between the hand
held transmitter
5and the integrated ga-
rage door opener depends on the garage
door drive system. Several attempts might
be necessary. You should test every position
for at least 25 seconds before trying another
position.
Synchronizing the rolling code
If the garage door system uses a rolling code,
you will also have to synchronize the garage
door system with the integrated garage door
opener in the rear-view mirror. To do this you
will need to use the programing button on the
door drive control panel. The programing buttonmay be positioned at different locations de-
pending on the manufacturer. It is usually lo-
cated on the door drive unit on the garage
ceiling.
Familiarize yourself with the garage door drive
operating instructions before carrying out the
following steps.
Your vehicle must be within reach of the garage
door or gate opener drive. Make sure that
neither your vehicle nor any persons/ objects
are present within the sweep of the door or
gate.
1. Turn the ignition key to the ON position.
2. Get out of the vehicle.
3. Press the programing button on the door
drive unit.
Usually, you now have 30 seconds to initiate
the next step.
4. Get into the vehicle.
5. Press previously programed button
2,3or4on the HomeLink® until the door
closes.
The rolling code synchronization is then com-
plete.
NDI1631
Instruments and controls2-87

WARNING
•Do not adjust the heater and air conditioner
controls or audio controls while driving so
that full attention may be given to vehicle
operation.
•Do not use this system if you notice any
abnormality, such as a frozen screen or lack
of sound. Continued use of the system may
result in accident, fire or electric shock.
•If you noticed any foreign objects entering
the system hardware, spilled liquid on the
system, or noticed smoke or fumes coming
out from the system, or any other unusual
operation is observed, stop using the sys-
tem immediately. It is recommended that
you contact the nearest INFINITI retailer. Ig-
noring such conditions may lead to an acci-
dent, fire or electric shock.
•Do not disassemble or modify this system.
If you do, it may lead to an accident, fire, or
electric shock.
•Park the vehicle in a safe location and apply
the parking brake to view the images on the
front center display screen.
CAUTION
Do not use the system when the engine is not
running for extended periods of time to pre-
vent battery discharge.
INFINITI CONTROLLER
1<MAP/VOICE>(models with navigation sys-
tem)
Push to display the vehicle’s current location on
the map.
NAA1625
SAFETY PRECAUTIONS CENTER MULTI FUNCTION CONTROL PANEL
4-2Display screen, heater and air conditioner, and audio system

Push again to display the Display View Bar and
the display views.
Push and hold to hear the current guidance for
a programmed route.
<
>(models without navigation system).
Push to display the hands-free phone operation
screen.
When you receive a phone call, push this switch
to answer the call.
2<MENU>Almost all functions, such as navi-
gation, apps, phone connection, information
screen display and other settings can be ac-
cessed from this menu. Icons and menus dis-
played on the screen may differ depending on
the models and specifications.
3</OK>Push to enter the selected item.
Nudge or rotate to select an item on the screen
or to adjust a setting (volume, brightness, etc.).
4<>Push to go back to the previous
screen.
5<AUDIO>Display the audio screen.
When<AUDIO>is pushed while the audio
screen is displayed, the source list screen will
be displayed.
6</ CAMERA>(models with
Around View Monitor system).Push to view the Around View Monitor screen.
Push and hold to control the brightness.
<
> (models without Around View Monitor
system)
Push for brightness control. Push and hold to
turn the display on/off.
STEERING WHEEL MOUNTED
CONTROLS
The steering wheel switch controls the volume,
voice recognition or Bluetooth® Hands-Free
Phone, or selects a menu.
It can also control audio and hands-free text
messaging assistant features that are shown on
the display.
1<>(TALK):
Push to enter the voice recognition
mode.
Giving voice commands
2<>(Phone End) :
End an active call and reject an incom-
ing call.
3Volume control switch:
The volume control switch allows you to
adjust the volume of the speakers by
pushing the + orbutton.
4<>(Mute):
Push to turn on/off the audio system.
5<>(Phone Send):
Make a call and accept an incoming call.
USB CONNECTION PORTS
The front console compartment contains the
USB connection ports.
NAA1624
Display screen, heater and air conditioner, and audio system4-3

1USB/iPod connection port:
Connect to play media from an iPod
R,
iPhone
Ror a USB memory device.
When using INFINITI InTouch Apps with
an iPhone
R, connect via a USB cable.
Refer to the device manufacturer’s owner
information regarding the proper use
and care of the device.
CAUTION
•Depending on the size and shape of USB
device, the console lid may not fully close.
Do not force the console lid closed as this
may damage the USB device.NOTE
•Even when iPodsRor iPhonesRare
connected to both of the two USB/iPod
Rconnection ports, the system recognizes only
one of the connected iPods
Ror iPhonesRat a time.
•Only one of the two connected USB devices
can be operated by the voice recognition
system.
STARTING SYSTEM
The system starts when the ignition switch is
placed in the ACC or ON position.
Start-up warning (models with
navigation system)
For this system, when the ignition switch is
placed in the ACC or ON position, the start-up
screen is displayed.
Touch [OK] after reading and agreeing to the
message. If you do not agree to the message,
some of Infiniti InTouch
TMfunctions will be
disabled.NOTE
•Do not keep the INFINITI InTouch system
turned on with the engine stopped. Doing so
may discharge the vehicle battery. When you
use INFINITI InTouch, always keep the engine
running.
•Once you select [Decline] on the start-up
screen, the [OK]/[Decline] screen will not be
displayed for 30 days.
NAA1628
4-4Display screen, heater and air conditioner, and audio system