light INFINITI QX4 2005 Factory Service Manual

TF-130
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: October 20052005 QX56
Heavy Tight-corner Braking Symptom OccursEDS002HT
SYMPTOM:
Heavy tight-corner braking symptom occurs when vehicle is driven in AUTO mode and steering wheel
is turned fully to either side.
DIAGNOSTIC PROCEDURE
NOTE:

Light tight-corner braking symptom may occur depending on driving conditions in AUTO mode. This is not
a malfunction.

Heavy tight-corner braking symptom occurs when vehicle is driven in the following conditions: 4WD shift
switch is "4H" or "4LO", steering wheel is turned fully to either side.
1. CHECK SYSTEM FOR CAN COMMUNICATION LINE
Perform self-diagnosis. Refer to TF-50, "
SELF-DIAGNOSTIC PROCEDURE (WITH CONSULT-II)" .
Is "CAN COMM CIRCUIT [U1000]" displayed?
YES >> Perform trouble diagnosis for CAN communication line. Refer to TF-113, "CAN Communication
Line" .
NO >> GO TO 2.
2. CHECK SYSTEM FOR 4WD SHIFT SWITCH
Perform trouble diagnosis for 4WD shift switch system. Refer to TF-62, "
4WD Shift Switch" .
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. CHECK ACCELERATOR PEDAL POSITION SIGNAL CIRCUIT
Perform self diagnosis for ECM. Refer to EC-49, "
Emission-related Diagnostic Information" .
Is any malfunction detected by self-diagnosis?
YES >> Check the malfunctioning system.
NO >> GO TO 4.
4. CHECK SYSTEM FOR CLUTCH PRESSURE SOLENOID
Perform trouble diagnosis for clutch pressure solenoid system. Refer to TF-105, "
Clutch Pressure Switch" .
OK or NG
OK >> GO TO 5.
NG >> Repair or replace damaged parts.
5. SYMPTOM CHECK
Check again.
OK or NG
OK >> Inspection End.
NG >> GO TO 6.
6. CHECK TRANSFER CONTROL UNIT
Check transfer control unit input/output signal. Refer to TF-36, "
Transfer Control Unit Input/Output Signal Ref-
erence Values" .
OK or NG
OK >> GO TO 7.
NG >> Check transfer control unit pin terminals for damage or loose connection with harness connector.
If any items are damaged, repair or replace damaged parts.

TF-178
TRANSFER ASSEMBLY
Revision: October 20052005 QX56
18. Apply liquid gasket to the entire center case mounting surface of
the front case assembly as shown.

Use Genuine Anaerobic Liquid Gasket or equivalent.
Refer to GI-45, "
Recommended Chemical Products and
Sealants" .
CAUTION:
Remove all foreign materials such as water, oil and grease
from center case and front case mating surfaces.
19. Install the center case assembly to the front case assembly.
CAUTION:
Do not damage mainshaft end.
20. Tap the center case lightly and press-fit the front drive shaft
bearing into the front case.
21. Tighten the front case bolts to the specified torque. Refer to TF-
144, "COMPONENTS" .
CAUTION:
Be sure to install air breather hose clamp, connector
bracket and harness clip.
22. Install the drain plug with a new gasket.
CAUTION:
Do not reuse gasket.
23. Align the matching mark on the front drive shaft with the mark on
the companion flange, then install the companion flange.
WDIA0157E
SDIA2138E
SDIA2100E
SDIA2779E

FRONT WIPER AND WASHER SYSTEM
WW-9
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: October 20052005 QX56
NOTE:
Each OUTPUT terminal transistor is activated at 10 ms intervals. Therefore, after the switch is turned ON,
electrical loads are activated with time delay. This time delay is so short that it cannot be detected by human
senses.
Operation Mode
The combination switch reading function has the operation modes shown below.
1. Normal status
–When BCM is not in sleep status, OUTPUT terminals (1-5) each turn ON-OFF every 10 ms.
2. Sleep status
–When BCM is in sleep status, transistors of OUTPUT 1 stop the output, and BCM enters low current con-
sumption mode. OUTPUT (2, 3, and 4) turn ON-OFF every 10 ms, and only input from light switch system
is accepted.
CAN Communication System DescriptionEKS00BDU
Refer to LAN-5, "CAN COMMUNICATION" .
SKIA4961E

WW-14
FRONT WIPER AND WASHER SYSTEM
Revision: October 20052005 QX56
Terminals and Reference Values for BCMEKS00BDX
Te r m i -
nal No.Wire
colorSignal nameMeasuring condition
Reference Value (V)
(Approx.) Ignition
switchOperation or condition
2 SB Combination switch input 5 ON

Light switch and wiper switch OFF

Wiper dial position 4
3 G/Y Combination switch input 4 ON

Light switch and wiper switch OFF

Wiper dial position 4
4 Y Combination switch input 3 ON

Light switch and wiper switch OFF

Wiper dial position 4
5 G/B Combination switch input 2
ON

Light switch and wiper switch OFF

Wiper dial position 4
6 V Combination switch input 1
32 R/G Combination switch output 5 ON

Light switch and wiper switch OFF

Wiper dial position 4
33 R/Y Combination switch output 4 ON

Light switch and wiper switch OFF

Wiper dial position 4
34 L Combination switch output 3 ON

Light switch and wiper switch OFF

Wiper dial position 4
SKIA5291E
SKIA5292E
SKIA5291E
SKIA5292E
SKIA5291E
SKIA5292E
SKIA5291E

FRONT WIPER AND WASHER SYSTEM
WW-15
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: October 20052005 QX56
Terminals and Reference Values for IPDM E/R EKS00BDY
Work FlowEKS00BDZ
1. Confirm the trouble symptom or customer complaint.
2. Understand the system description, refer to WW-4, "
System Description" .
3. Perform preliminary inspection, refer to WW-15, "
Preliminary Inspection" .
4. Check symptom and repair or replace the cause of malfunction.
5. Does wiper function operate normally? If it operates normally, GO TO 6. If not, GO TO 4.
6. Inspection End.
Preliminary InspectionEKS00BE0
INSPECTION FOR POWER SUPPLY AND GROUND CIRCUIT
Inspection procedure
1. CHECK FUSE
Check if wiper or washer fuse is blown.
35 O/B Combination switch output 2
ON

Light switch and wiper switch OFF

Wiper dial position 4
36 R/W Combination switch output 1
38 W/L Ignition switch (ON) ON — Battery
39 L CAN-H ON — —
40 P CAN-L ON — —
67 B Ground — — 0
70 W/B Battery power OFF — Battery Te r m i -
nal No.Wire
colorSignal nameMeasuring condition
Reference Value (V)
(Approx.) Ignition
switchOperation or condition
SKIA5292E
Te r m i n a l
No.Wire
colorSignal nameMeasuring condition
Reference value (V)
(Approx.) Ignition
switchOperation or condition
32 L Low speed signal ON Wiper switchOFF 0
LO Battery
35 L/B High speed signal ON Wiper switchOFF 0
HI Battery
38 B Ground — — 0
39 L CAN-H ON — —
40 P CAN-L ON — —
43 L/Y Wiper auto stop signal ONWiper operating Battery
Wiper stopped 0
59 B Ground — — 0
Unit Power source Fuse No.
Front and rear washer motor Ignition switch ON or START 9
Front wiper relay Battery 39
BCMIgnition switch ON or START 59
Battery f

REAR WIPER AND WASHER SYSTEM
WW-41
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: October 20052005 QX56
Terminals and Reference Values for BCMEKS00BEE
Te r m i -
nal No.Wire
colorSignal nameMeasuring condition
Reference Value (V)
(Approx.) Ignition
switchOperation or condition
2 SB Combination switch input 5 ON

Light switch and wiper switch OFF

Wiper dial position 4
3 G/Y Combination switch input 4 ON

Light switch and wiper switch OFF

Wiper dial position 4
4 Y Combination switch input 3 ON

Light switch and wiper switch OFF

Wiper dial position 4
5 G/B Combination switch input 2 ON

Light switch and wiper switch OFF

Wiper dial position 4
6 V Combination switch input 1 ON
26 Y/LRear wiper auto stop
switch 2ONRise up position (rear wiper arm on
stopper)0V
A Position (full clockwise stop
position)0V
Forward sweep (counterclockwise
direction)Fluctuating
B Position (full counterclockwise stop
position)Battery voltage
Reverse sweep (clockwise direction) Fluctuating
32 R/G Combination switch output 5 ON

Light switch and wiper switch OFF

Wiper dial position 4
SKIA5291E
SKIA5292E
SKIA5291E
SKIA5292E
SKIA5291E

WW-42
REAR WIPER AND WASHER SYSTEM
Revision: October 20052005 QX56
33 R/Y Combination switch output 4 ON
Light switch and wiper switch OFF

Wiper dial position 4
34 L Combination switch output 3 ON

Light switch and wiper switch OFF

Wiper dial position 4
35 O/B Combination switch output 2 ON

Light switch and wiper switch OFF

Wiper dial position 4
36 R/W Combination switch output 1 ON
38 W/L Ignition switch (ON) ON — Battery voltage
42 GRGlass hatch ajar switch
signalONHatch glass closed Battery voltage
Hatch glass open 0V
44 ORear wiper auto stop
switch 1ONRise up position (rear wiper arm on
stopper)0V
A Position (full clockwise stop
position)Battery voltage
Forward sweep (counterclockwise
direction)Fluctuating
B Position (full counterclockwise stop
position)0V
Reverse sweep (clockwise direction) Fluctuating
54 Y Rear wiper output circuit 2 ONRise up position (rear wiper arm on
stopper)0V
A Position (full clockwise stop
position)0V
Forward sweep (counterclockwise
direction)0V
B Position (full counterclockwise stop
position)Battery voltage
Reverse sweep (clockwise direction) Battery voltage Te r m i -
nal No.Wire
colorSignal nameMeasuring condition
Reference Value (V)
(Approx.) Ignition
switchOperation or condition
SKIA5292E
SKIA5291E
SKIA5292E