ECU INFINITI QX56 2006 Factory Manual PDF

BL-1
BODY, LOCK & SECURITY SYSTEM
I BODY
CONTENTS
C
DE
F
G H
J
K L
M
SECTION
A
B
BL
Revision: November 2009 2006 QX56
PRECAUTIONS .....................................................
..... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 4
Precautions for work ................................................ 4
PREPARATION ...................................................... ..... 5
Special service tool ............................................. ..... 5
Commercial Service Tool .................................... ..... 5
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 6
Work Flow ................................................................ 6 CUSTOMER INTERVIEW ................................ ..... 6
DUPLICATE THE NOISE AND TEST DRIVE .. ..... 7
CHECK RELATED SERVICE BULLETINS ...... ..... 7
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ................................................. ..... 7
REPAIR THE CAUSE ...................................... ..... 7
CONFIRM THE REPAIR .................................. ..... 8
Generic Squeak and Rattle Troubleshooting ...... ..... 8
INSTRUMENT PANEL ..................................... ..... 8
CENTER CONSOLE ........................................ ..... 8
DOORS ............................................................ ..... 8
TRUNK ............................................................. ..... 9
SUNROOF/HEADLINING ................................ ..... 9
OVERHEAD CONSOLE (FRONT AND REAR) ..... 9
SEATS .............................................................. ..... 9
UNDERHOOD .................................................. ..... 9
Diagnostic Worksheet ......................................... ... 10
HOOD .................................................................... ... 12
Fitting Adjustment ............................................... ... 12
CLEARANCE AND SURFACE HEIGHT
ADJUSTMENT ................................................. ... 13
HOOD LOCK ADJUSTMENT .......................... ... 13
Removal and Installation of Hood Assembly ....... ... 13
Removal and Installation of Hood Lock Control .. ... 14
REMOVAL ........................................................ ... 14
INSTALLATION ................................................ ... 15
Hood Lock Control Inspection ............................. ... 15
POWER DOOR LOCK SYSTEM ........................... ... 16
Component Parts and Harness Connector Location ... 16
System Description ............................................. ... 17OUTLINE ..........................................................
... 18
Schematic ............................................................ ... 19
Wiring Diagram — D/LOCK — ............................ ... 20
Terminals and Reference Value for BCM ............ ... 25
Work Flow ............................................................... 25
CONSULT–II Function (BCM) ............................. ... 26
CONSULT–II INSPECTION PROCEDURE ...... ... 26
DATA MONITOR .............................................. ... 27
ACTIVE TEST ..................................................... 28
Trouble Diagnoses Symptom Chart .................... ... 29
BCM Power Supply and Ground Circuit Check ... ... 29
Door Switch Check ................................................. 31
Key Switch (Insert) Check ................................... ... 33
Door Lock/Unlock Switch Check ............................ 34
Glass Hatch Switch Circuit Inspection ................. ... 36
Front Door Lock Assembly LH (Actuator) Check . ... 38
Front Door Lock Actuator RH Check ................... ... 39
Rear Door Lock Actuator RH/LH Check .............. ... 40
Glass Hatch Lock Actuator Check .......................... 41
Front Door Lock Assembly LH (Key Cylinder Switch)
Check .................................................................. ... 42
REMOTE KEYLESS ENTRY SYSTEM .................. ... 44
Component Parts and Harness Connector Location ... 44
System Description .............................................. ... 45
INPUTS ............................................................ ... 45
OPERATING PROCEDURE ............................. ... 46
CAN Communication System Description ........... ... 48
Schematic ............................................................ ... 49
Wiring Diagram — KEYLES — ............................ ... 50
......................................................................... ... 50
......................................................................... ... 51
......................................................................... ... 52
Terminals and Reference Value for BCM ............ ... 53
Terminals and Reference Value for IPDM E/R .... ... 54
CONSULT-II Function (BCM) .............................. ... 55
CONSULT-II Inspection Procedure ...................... ... 55
“MULTI REMOTE ENT” .................................... ... 55
CONSULT-II Application Items ............................ ... 56
“MULTI REMOTE ENT” .................................... ... 56
Trouble Diagnosis Procedure .............................. ... 59

BL-2Revision: November 20092006 QX56
BCM Power Supply and Ground Circuit Check ...
... 59
Trouble Diagnoses ............................................... ... 60
SYMPTOM CHART ............................................. 60
Key Switch (Insert) Check ...................................... 62
Door Switch Check .............................................. ... 63
Keyfob Battery and Function Check .................... ... 65
Remote Keyless Entry Receiver System Check .. ... 66
ACC Power Check ............................................... ... 68
IPDM E/R Operation Check ................................. ... 68
Check Hazard Function ....................................... ... 70
Check Horn Function ........................................... ... 70
Check Headlamp Function .................................. ... 70
Check Map Lamp Illumination Function .............. ... 70
ID Code Entry Procedure .................................... ... 71
KEYFOB ID SET UP WITH CONSULT-II ......... ... 71
KEYFOB ID SET UP WITHOUT CONSULT-II .. ... 73
Keyfob Battery Replacement ............................... ... 74
VEHICLE SECURITY (THEFT WARNING) SYSTEM ... 75
Component Parts and Harness Connector Location ... 75
System Description .............................................. ... 76
DESCRIPTION ................................................. ... 76
POWER SUPPLY AND GROUND CIRCUIT .... ... 77
INITIAL CONDITION TO ACTIVATE THE SYS-
TEM .................................................................. ... 77
VEHICLE SECURITY SYSTEM ALARM OPER-
ATION ............................................................... ... 77
VEHICLE SECURITY SYSTEM DEACTIVATION ... 78
PANIC ALARM OPERATION ............................ ... 78
CAN Communication System Description ........... ... 78
Schematic ............................................................ ... 79
Wiring Diagram — VEHSEC — ........................... ... 80
.......................................................................... ... 80
.......................................................................... ... 81
.......................................................................... ... 82
.......................................................................... ... 83
.......................................................................... ... 84
Terminals and Reference Value for BCM ............. ... 85
Terminals and Reference Value for IPDM E/R ..... ... 86
CONSULT-II Function (BCM) ............................... ... 86
CONSULT-II INSPECTION PROCEDURE ....... ... 86
CONSULT-II APPLICATION ITEM .................... ... 88
Trouble Diagnosis ................................................ ... 89
WORK FLOW ................................................... ... 89
Preliminary Check ............................................... ... 90
Symptom Chart ....................................................... 91
Door Switch Check .............................................. ... 92
Hood Switch Check ............................................. ... 94
Combination Meter (Security Indicator Lamp)
Check .................................................................. ... 95
Front Door Lock Assembly LH (Key Cylinder Switch)
Check .................................................................. ... 96
Vehicle Security Horn Alarm Check ..................... ... 98
Vehicle Security Headlamp Alarm Check ............ ... 98
Door Lock/Unlock Switch Check ............................ 98
AUTOMATIC BACK DOOR SYSTEM .................... ... 99
Component Parts and Harness Connector Location ... 99
System Description .............................................. .100
OPERATION DESCRIPTION ........................... .100
Schematic ............................................................ .105Wiring Diagram — B/CLOS — .............................
.106
Terminals and Reference Value for Back Door Con-
trol Unit ................................................................. . 111
Terminals and Reference Value for BCM ............. .112
Trouble Diagnosis Procedure ............................... .113
Self-Diagnosis Procedures .................................. .113
INPUT SIGNAL CHECK MODE ........................ .113
OPERATING CHECK MODE ............................ .113
Diagnosis Chart ................................................... .114
Back Door Power Supply and Ground Circuit
Inspection ............................................................. .115
Power Liftgate Switch System Inspection ............ .116
GLASS HATCH AJAR SWITCH CHECK .......... .117
Back Door Close (Close) Switch System Inspection .118
Back Door Close (Cancel) Switch System Inspec-
tion ....................................................................... .119
Pinch Strip System Inspection ............................. .121
Back Door Warning Chime System Inspection .... .122
Half-Latch Switch System Inspection ................... .122
Open Switch System Inspection .......................... .123
Close Switch System Inspection .......................... .124
Back Door Handle Switch System Inspection ...... .125
Cinch Latch Motor System Inspection ................. .126
DOOR ..................................................................... .128
Fitting Adjustment ................................................ .128
FRONT DOOR .................................................. .128
REAR DOOR .................................................... .128
STRIKER ADJUSTMENT ................................. .128
Removal and Installation ...................................... .129
FRONT DOOR .................................................. .129
REAR DOOR .................................................... .129
BACK DOOR .................................................... .130
FRONT DOOR LOCK ............................................. .131
Component Structure ........................................... .131
Removal and Installation ...................................... .131
REMOVAL ......................................................... .131
INSTALLATION ................................................. .133
Disassembly and Assembly ................................. .133
DOOR KEY CYLINDER ASSEMBLY ................ .133
REAR DOOR LOCK ............................................... .134
Component Structure ........................................... .134
Removal and Installation ...................................... .134
REMOVAL ......................................................... .134
INSTALLATION ................................................. .134
BACK DOOR LOCK ............................................... .135
Power Back Door Opener .................................... .135
REMOVAL ........................................................ .135
INSTALLATION ................................................ .135
Door Lock Assembly ............................................ .136
REMOVAL ........................................................ .136
INSTALLATION ................................................ .136
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ..................................................................... .137
Component Parts and Harness Connector Location .137
System Description .............................................. .138
System Composition ............................................ .138
ECM Re-communicating Function ....................... .139
Wiring Diagram — NATS — ................................. .140
Terminals and Reference Value for BCM ............. .141

SQUEAK AND RATTLE TROUBLE DIAGNOSESBL-7
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
DUPLICATE THE NOISE AND TEST DRIVE
If possible, drive the vehicle with the customer until the noise is duplicated. Note any additional information on
the Diagnostic Worksheet regarding the conditions or location of the noise. This information can be used to
duplicate the same conditions when you confirm the repair.
If the noise can be duplicated easily during the test drive, to help identify the source of the noise, try to dupli-
cate the noise with the vehicle stopped by doing one or all of the following:
1) Close a door.
2) Tap or push/pull around the area where the noise appears to be coming from.
3) Rev the engine.
4) Use a floor jack to recreate vehicle “twist”.
5) At idle, apply engine load (electrical load, half-clutch on M/T model, drive position on A/T model).
6) Raise the vehicle on a hoist and hit a tire with a rubber hammer.

Drive the vehicle and attempt to duplicate the conditions the customer states exist when the noise occurs.

If it is difficult to duplicate the noise, drive the vehicle slowly on an undulating or rough road to stress the
vehicle body.
CHECK RELATED SERVICE BULLETINS
After verifying the customer concern or symptom, check ASIST for Technical Service Bulletins (TSBs) related
to that concern or symptom.
If a TSB relates to the symptom, follow the procedure to repair the noise.
LOCATE THE NOISE AND IDENTIFY THE ROOT CAUSE
1. Narrow down the noise to a general area.To help pinpoint the source of the noise, use a listening tool (Chassis Ear: J-39570, Engine Ear: J-39565 and mechanic's stethoscope).
2. Narrow down the noise to a more specific area and identify the cause of the noise by:

removing the components in the area that you suspect the noise is coming from.
Do not use too much force when removing clips and fasteners, otherwise clips and fasteners can be bro-
ken or lost during the repair, resulting in the creation of new noise.

tapping or pushing/pulling the component that you suspect is causing the noise.
Do not tap or push/pull the component with excessive force, otherwise the noise will be eliminated only
temporarily.

feeling for a vibration with your hand by touching the component(s) that you suspect is (are) causing the
noise.

placing a piece of paper between components that you suspect are causing the noise.

looking for loose components and contact marks.
Refer to BL-8, "
Generic Squeak and Rattle Troubleshooting" .
REPAIR THE CAUSE

If the cause is a loose component, tighten the component securely.

If the cause is insufficient clearance between components:
–separate components by repositioning or loosening and retightening the component, if possible.
–insulate components with a suitable insulator such as urethane pads, foam blocks, felt cloth tape or ure-
thane tape. A NISSAN Squeak and Rattle Kit (J-43980) is available through your authorized NISSAN
Parts Department.
CAUTION:
Do not use excessive force as many components are constructed of plastic and may be damaged.
Always check with the Parts Department for the latest parts information.
The following materials are contained in the NISSAN Squeak and Rattle Kit (J-43980). Each item can be
ordered separately as needed.
URETHANE PADS [1.5 mm (0.059 in) thick]
Insulates connectors, harness, etc.
76268-9E005: 100 ×135 mm (3.94 ×5.31 in)/76884-71L01: 60× 85 mm (2.36×3.35 in)/76884-71L02: 15 ×25
mm (0.59 ×0.98 in)
INSULATOR (Foam blocks)
Insulates components from contact. Can be used to fill space behind a panel.
73982-9E000: 45 mm (1.77 in) thick, 50 ×50 mm (1.97 ×1.97 in)/73982-50Y00: 10 mm (0.39 in) thick,
50 ×50 mm (1.97 ×1.97 in)
INSULATOR (Light foam block)

SQUEAK AND RATTLE TROUBLE DIAGNOSESBL-9
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
TRUNK
Trunk noises are often caused by a loose jack or loose items put into the trunk by the owner.
In addition look for:
1. Trunk lid bumpers out of adjustment
2. Trunk lid striker out of adjustment
3. The trunk lid torsion bars knocking together
4. A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1. Sunroof lid, rail, linkage or seals making a rattle or light knocking noise
2. Sun visor shaft shaking in the holder
3. Front or rear windshield touching headliner and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.
OVERHEAD CONSOLE (FRONT AND REAR)
Overhead console noises are often caused by the console panel clips not being engaged correctly. Most of
these incidents are repaired by pushing up on the console at the clip locations until the clips engage.
In addition look for:
1. Loose harness or harness connectors.
2. Front console map/reading lamp lense loose.
3. Loose screws at console attachment points.
SEATS
When isolating seat noise it's important to note the position the seat is in and the load placed on the seat when
the noise is present. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1. Headrest rods and holder
2. A squeak between the seat pad cushion and frame
3. The rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1. Any component mounted to the engine wall
2. Components that pass through the engine wall
3. Engine wall mounts and connectors
4. Loose radiator mounting pins
5. Hood bumpers out of adjustment
6. Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.

HOODBL-15
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
INSTALLATION
1. Pull the hood lock cable through the dash lower hole into the engine room.
Be careful not to bend the cable too much, keeping the radius
100mm (3.94 in) or more.
2. Make sure the cable is not offset from the positioning grommet, and push the grommet into the dash lower hole securely.
3. Apply sealant around the grommet at * mark.
4. Install the primary and secondary cables securely to the hood lock.
5. Install the hood lock and the secondary hood lock release assemblies.
6. Check the hood lock adjustment and hood opener operation. Refer to BL-12, "
Fitting Adjustment" .
Hood Lock Control InspectionEIS004QA
CAUTION:
If the hood lock cable is bent or deformed, replace it.
1. Remove the front grille. Refer to EI-17, "
FRONT GRILLE" .
2. Make sure the secondary latch is properly engaged with the sec- ondary striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height.
3. While operating the hood opener, carefully make sure the front end of the hood is raised by approx. 20 mm (0.79 in). Also make
sure the hood opener returns to the original position.
4. Check the hood lock lubrication condition. If necessary, apply “body grease ” to the points shown in the figure.
5. Install the front grille. Refer to EI-17, "
FRONT GRILLE" .
PIIA0173E
PIIA0174E
PIIA1086E
PIIA0176E

BL-26
POWER DOOR LOCK SYSTEM
Revision: November 20092006 QX56
CONSULT–II Function (BCM)EIS005ZD
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT–II INSPECTION PROCEDURE
CONSULT-II can display each diagnostic item using the following diagnostic test modes: data monitor, active
test, and CAN diagnostic support monitor through data reception and command transmission via the BCM
communication line.
"DOOR LOCK"
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. Turn ignition switch OFF.
2. Connect CONSULT-II and CONSULT-II CONVERTER to the
data link connector.
3. Turn ignition switch ON.
4. Touch “START (NISSAN BASED VHCL) ”.
BCM
diagnostic test item Diagnostic mode
Description
Inspection by part WORK SUPPORT
Supports inspections and adjustments. Commands are transmitted to the
BCM for setting the status suitable for required operation, input/output sig-
nals are received from the BCM and received date is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to
them.
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be
read.
ECU PART NUMBER BCM part number can be read. CONFIGURATION Performs BCM configuration read/write functions.
BBIA0369E
BCIA0029E

BL-46
REMOTE KEYLESS ENTRY SYSTEM
Revision: November 20092006 QX56
OPERATING PROCEDURE

When the keyfob is operated, the signal from the keyfob is sent and the remote keyless entry receiver
receives the signal and sends it to the BCM. The BCM only locks/unlocks the doors if the ID number
matches. (Remote control entry functions)

Using the keyfob, the transmitter sends radio waves to the remote keyless entry receiver, which then
sends the received waves to the BCM. Only if the ID number matches does the BCM lock/unlock the
doors. (Remote control door function)

Unless the key is inserted into the ignition key cylinder or one of the doors is opened within 1 minute after
the UNLOCK switch on the keyfob is pressed, all the doors are automatically locked. (Auto lock function)

When a door is locked or unlocked, the vehicle turn signal lamps flash and the horn sounds to verify oper-
ation. (Active check function)

When the key is in the ignition key cylinder (when the key switch is ON) and one of the doors is open, the
door lock function does not work even when the door lock is operated with the keyfob.

Keyfob ID set up is available.

If a keyfob is lost, a new keyfob can be set up. A maximum of 5 IDs can be set up simultaneously.
Remote Control Entry Functions
Operation Description

When a button on the keyfob is operated, the signal is sent from the keyfob and received by the remote
keyless entry receiver.

The received signal is sent to the BCM and compared with the registered ID number.

If the ID number matches, the BCM sends the lock/unlock signal to each door lock actuator.

When the door lock actuators receive this signal, each operates to lock/unlock its door.

BCM locks all doors with input of LOCK signal from keyfob.

When an UNLOCK signal is sent from keyfob once, driver's door will be unlocked.

Then, if an UNLOCK signal is sent from keyfob again within 5 seconds, all other doors will be unlocked.
Remote control entry operation conditions
Auto Lock Function
Operation Description

Unless the key is inserted into the ignition key cylinder, one of the doors is opened, or the keyfob is oper-
ated within 1 minute after a door lock is unlocked by keyfob operation, all the doors are automatically
locked.
The 1 minute timer count is executed by the BCM and after 1 minute, the BCM sends the lock signal to all
doors.
Lock operations are the same as for the remote control entry function.
Remote Control Automatic Back Door Function
Switching from all closed to all open

When a button on the keyfob is operated, the signal is sent from the keyfob and received by the remote
keyless entry receiver.

The received signal is sent to the BCM and compared with the registered ID number.

If the ID number matches, the BCM uses power window serial link communication to send the back door
open signal to the back door control unit

When the back door control unit receives the back door open signal for 0.5 seconds, if the remote control
automatic back door operation enable conditions are met, the warning chime is sounded and the back
door unlock signal is sent to the back door latch using communication.

When the back door latch receives the back door unlock signal, it operates the release actuator and
releases to back door latch.
Keyfob operation Operation condition
Door lock operation (locking)

With key removed (key switch: OFF)

Closing all doors (door switch: OFF)
Door lock operation (unlocking) With key removed (key switch: OFF)

REMOTE KEYLESS ENTRY SYSTEMBL-47
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56

The back door control unit operates the back door motor to open the back door. (At this time, speed con-
trol, input reverse, and overload reverse control are executed.)

When the back door is opened to the fully open position, the full-open position is detected with the rotation
sensor, the back door motor is stopped.

The door held by the back door stays at the full open position.
Full open → full closed operation

When a button of the keyfob is operated, the signal is sent from the keyfob and received by the remote
keyless entry receiver.

The received signal is sent to the BCM and compared with the registered ID number.

If the ID number matches, the BCM uses power window serial link communication to send the back door
close request signal to the back door control unit.

When the back door control unit receives the back door close request signal for 0.5 seconds, if the remote
control automatic back door operation enable conditions are met, the warning chime is sounded and the
back door motor begins closing the back door.

The back door control unit operates the magnetic clutch and the back door motor to close the back door.
(At this time, the back door control unit executes speed control, input reverse, and overload reverse con-
trol.)

When the back door comes to the half-latch state, the back door latch detects the half-latch state through
half-latch switch operation. The back door latch latches the back door.
For the automatic back door system operation enable conditions, refer to BL-99, "
AUTOMATIC BACK DOOR
SYSTEM" .
Active Check Function
Operation Description
When a door is locked or unlocked by keyfob operation, the vehicle turn signals flash and the horn sounds to
verify operation.

When a button on the keyfob is operated, the signal is sent from the remote controller and received by the
keyless remote entry receiver.

The received signal is sent to the BCM and compared with the registered ID number.

If the ID number matches, the BCM sends the turn signal flashing and horn signal to the IPDM E/R.

The IPDM E/R flashes the turn signal lamps and sounds the horn for each keyfob operation.
Operating function of hazard and horn reminder
Hazard and Horn Reminder
BCM output to IPDM E/R for horn reminder signal as DATA LINE (CAN-H and CAN-L).
The hazard and horn reminder has C mode (horn chirp mode) and S mode (non-horn chirp mode).
How to change hazard and horn reminder mode With CONSULT-II
Hazard and horn reminder can be changed using “WORK SUPPORT” mode in “MULTI ANSWER BACK SET".
Without CONSULT-II
Refer to Owner's Manual for instructions.
Interior Lamp Operation
When the following input signals are both supplied:

all door switches are in the OFF position. (when all the doors are closed);

interior lamp switch is in DOOR position.
Remote keyless entry system turns on interior lamp and ignition keyhole illumination (for 30 seconds) with
input of UNLOCK signal from keyfob.
For detailed description, refer to LT- 1 3 6 , "
ROOM LAMP TIMER OPERATION" .
C mode S mode
Keyfob operation LockUnlock LockUnlock
Hazard warning lamp
flash Twice
OnceTwice —
Horn sound Once———

REMOTE KEYLESS ENTRY SYSTEMBL-55
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
CONSULT-II Function (BCM)EIS005ZW
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II Inspection ProcedureEIS005ZX
CONSULT-II can display each diagnostic item using the following diagnostic test modes: work support, data
monitor, active test, and CAN diagnostic support monitor through data reception and command transmission
via the BCM communication line.
“MULTI REMOTE ENT”
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. Turn ignition switch OFF.
2. Connect CONSULT-II and CONSULT-II CONVERTER to the
data link connector.
3. Turn ignition switch ON.
4. Touch “START (NISSAN BASED VHCL)".
BCM
diagnostic test item Diagnostic mode
Description
Inspection by part WORK SUPPORT
Supports inspections and adjustments. Commands are transmitted to the
BCM for setting the status suitable for required operation, input/output sig-
nals are received from the BCM and received date is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to
them.
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be
read.
ECU PART NUMBER BCM part number can be read. CONFIGURATION Performs BCM configuration read/write functions.
BBIA0369E
BCIA0029E

VEHICLE SECURITY (THEFT WARNING) SYSTEMBL-75
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
VEHICLE SECURITY (THEFT WARNING) SYSTEMPFP:28491
Component Parts and Harness Connector LocationEIS0060E
LIIA2374E
1. Fuse block (J/B)2. Fuse and fusible link box3. IPDM E/R fuse layout
4. IPDM E/R E122, E123, E124 5. Steering column
(view with instrument panel LH
removed) 6. Data link connector M22
(view with instrument panel LH
removed)