battery INFINITI QX56 2009 Factory Owner's Manual

ADP-60
< COMPONENT DIAGNOSIS >
PEDAL ADJUSTING SWITCH
1. Disconnect driver seat control unit and pedal adjusting switch.
2. Check continuity between driver seat control unit harness con-nector and pedal adjusting switch harness connector.
3. Check continuity between driver seat control unit harness con- nector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1. Connect the driver seat control unit.
2. Turn ignition switch OFF.
3. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace driver seat control unit. Refer to ADP-165, "Removal and Installation"
.
4. CHECK PEDAL ADJUSTING SWITCH
Refer to ADP-61, "Component Inspection"
.
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace pedal adjusting switch. Refer to IP-12, "Exploded View"
.
5. CHECK PEDAL ADJUSTING SWITCH GROUND CIRCUIT
Check continuity between pedal adjusting switch connector M96 ter-
minal 1 and ground.
Is the inspection result normal?
YES >> GO TO 6
NO >> Repair or replace harness.
6. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "Intermittent Incident"
.
Driver seat
control unit connector Te r m i n a l
Pedal adjusting
switch connector Terminal Continuity
B202 15
M96 2
Ye s
30 3
Driver seat control unit connector Te r m i n a l
GroundContinuity
B202 15
No
30
LIIA0726E
Driver seat control unit
connector Te r m i n a l s
Voltage (V)
(Approx.)
(+) (–)
B202 15
Ground Battery voltage
30
PIIA4591E
1 - Ground : Continuity should exist.
LIIA1015E
Revision: December 20092009 QX56

ADP-70
< COMPONENT DIAGNOSIS >
DETENTION SWITCH
DETENTION SWITCH
DescriptionINFOID:0000000003775590
Park position switch is installed on A/T shift selector. It is turned OFF when the A/T selector lever is in P posi-
tion. The driver seat control unit judges that the A/T select or lever is in P position if continuity does not exist in
this circuit.
Component Function CheckINFOID:0000000003775591
1. CHECK FUNCTION
1. Select “DETENT SW” signal in “D ata monitor” mode with CONSULT-III.
2. Check park position switch signal under the following conditions.
Is the indication normal?
YES >> Inspection End.
NO >> Perform diagnosis procedure. Refer to ADP-70, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000003775592
1. CHECK DTC WITH “BCM”
Check “Self Diagnostic Result” for BCM with CONSULT-lll.
Is any other DTC detected?
YES >> Check the DTC.
NO >> GO TO 2
2. CHECK PARK POSITION SWITCH INPUT SIGNAL
1. Turn ignition switch ON.
2. Mechanical key must be removed from the key switch.
3. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> GO TO 3
3. CHECK PARK POSITION SWITCH CIRCUIT
Monitor item Condition Status
DETENT SW A/T selector lever P position OFF
Other than
above
ON
Driver seat
control unit connector Te r m i n a l
ConditionVoltage (V)
(Approx.)
(+) (-)
B202 21 Ground A/T selec-
tor leverP position
Battery volt-
age
Other than
above 0V
ALJIA0193ZZ
Revision: December 20092009 QX56

ADP-90
< COMPONENT DIAGNOSIS >
SLIDING MOTOR
SLIDING MOTOR
DescriptionINFOID:0000000003775621
 The sliding motor LH is installed to the power seat frame assembly.
 The sliding motor LH is activated by the driver seat control unit.
 The seat is slid forward/backward by changing the rotation direction of sliding motor LH.
Component Function CheckINFOID:0000000003775622
1. CHECK FUNCTION
1. Select “SEAT SLIDE” in “Act ive test” mode with CONSULT-III.
2. Check the sliding motor LH operation.
Is the operation of relevant parts normal?
YES >> Inspection End.
NO >> Perform diagnosis procedure. Refer to ADP-90, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000003775623
1. CHECK SLIDING MOTOR LH POWER SUPPLY
1. Turn the ignition switch OFF.
2. Perform “Active test” (“SEAT SLIDE”) with CONSULT-lll
3. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> Replace sliding motor LH. (Built in power seat frame assembly). Refer to SE-68, "Disassembly
and Assembly".
NO >> GO TO 2
2. CHECK SLIDING MOTOR LH CIRCUIT
Test Item Description
SEAT SLIDE OFF
Seat sliding Sto p
FR Forward
RR Backward
Te r m i n a l
Test ItemVoltage (V)
(Approx.)
(+)
(-)
Driver seat
control unit connector Te r m i n a l
B203 35
Ground SEAT
SLIDE OFF 0
FR (forward) Battery voltage
RR (backward) 0
42 OFF 0
FR (forward) 0
RR (backward) Battery voltage
PIIA4801E
Revision: December 20092009 QX56

ADP-92
< COMPONENT DIAGNOSIS >
RECLINING MOTOR
RECLINING MOTOR
DescriptionINFOID:0000000003775624
 The reclining motor LH is installed to the seatback assembly.
 The reclining motor LH is activated with the driver seat control unit.
 The seatback is reclined forward/backward by changing the rotation direction of reclining motor LH.
Component Function CheckINFOID:0000000003775625
1. CHECK FUNCTION
1. Select “SEAT RECLINING” in “A ctive test” mode with CONSULT-III.
2. Check the reclining motor LH operation.
Is the operation of relevant parts normal?
YES >> Inspection End.
NO >> Perform diagnosis procedure. Refer to ADP-92, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000003775626
1. CHECK RECLINING MOTOR LH POWER SUPPLY
1. Turn the ignition switch OFF.
2. Perform “Active test” (“SEA T RECLINING”) with CONSULT-lll
3. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> Replace reclining motor LH. (Built in seatback assembly). Refer to SE-68, "Disassembly and
Assembly".
NO >> GO TO 2
2. CHECK RECLINING MOTOR LH CIRCUIT
Test Item Description
SEAT RECLINING OFF
Seat reclining Sto p
FR Forward
RR Backward
Te r m i n a l
Te s t I t e mVoltage (V)
(Approx.)
(+)
(-)
Driver
seat con- trol unit
connector Te r m i n a l
B203 36
Ground SEAT RE-
CLINING OFF 0
FR (forward) Battery voltage
RR (backward) 0
44 OFF 0
FR (forward) 0
RR (backward) Battery voltage
PIIA4802E
Revision: December 20092009 QX56

ADP-94
< COMPONENT DIAGNOSIS >
LIFTING MOTOR (FRONT)
LIFTING MOTOR (FRONT)
DescriptionINFOID:0000000003775627
 The lifting motor (front) is installed to the power seat frame assembly.
 The lifting motor (front) is activated with the driver seat control unit.
 The lifter (front) is moved upward/downward by changing the rotation direction of lifting motor (front).
Component Function CheckINFOID:0000000003775628
1. CHECK FUNCTION
1. Select “SEAT LIFTER FR” in “Active test” mode with CONSULT-III.
2. Check the lifting motor (front) operation.
Is the operation of relevant parts normal?
YES >> Inspection End.
NO >> Perform diagnosis procedure. Refer to ADP-94, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000003775629
1. CHECK LIFTING MOTOR (FRONT) POWER SUPPLY
1. Turn the ignition switch OFF.
2. Perform “Active test” (“SEAT LIFTER FR”) with CONSULT-lll.
3. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> Replace lifting motor (front). (Built in power seat frame assembly). Refer to SE-68, "Disassembly
and Assembly".
NO >> GO TO 2
2. CHECK LIFTING MO TOR (FRONT) CIRCUIT
Test Item Description
SEAT LIFTER FR OFF
Seat lifting (front) Sto p
UP Upward
DWN Downward
Te r m i n a l
Test ItemVoltage (V)
(Approx.)
(+)
(-)
Driver seat
control unit connector Te r m i n a l
B203 37
Ground SEAT
LIFTER
FR OFF 0
UP 0
DWN (down) Battery voltage
45 OFF 0
UP Battery voltage
DWN (down) 0
PIIA4805E
Revision: December 20092009 QX56

ADP-96
< COMPONENT DIAGNOSIS >
LIFTING MOTOR (REAR)
LIFTING MOTOR (REAR)
DescriptionINFOID:0000000003775630
 The lifting motor (rear) is installed to the power seat frame assembly.
 The lifting motor (rear) is activated with the driver seat control unit.
 The seat lifter (rear) is moved upward/downward by changing the rotation direction of lifting motor (rear).
Component Function CheckINFOID:0000000003775631
1. CHECK FUNCTION
1. Select “SEAT LIFTER RR” in “A ctive test” mode with CONSULT-III.
2. Check the lifting motor (rear) operation.
Is the operation of relevant parts normal?
YES >> Inspection End.
NO >> Perform diagnosis procedure. Refer to ADP-96, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000003775632
1. CHECK LIFTING MOTOR (REAR) POWER SUPPLY
1. Turn the ignition switch OFF.
2. Perform “Active test” (“SEAT LIFTER RR”) with CONSULT-lll
3. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> Replace lifting motor (rear). (Built in power seat frame assembly). Refer to SE-68, "Disassembly
and Assembly".
NO >> GO TO 2
2. CHECK LIFTING MO TOR (REAR) CIRCUIT
Test Item Description
SEAT LIFTER RR OFF
Seat lifting (rear) Sto p
UP Upward
DWN Downward
Te r m i n a l
Test ItemVoltage (V)
(Approx.)
(+)
(-)
Driver seat
control unit connector Te r m i n a l
B203 38
Ground SEAT
LIFTER
RROFF 0
UP Battery voltage
DWN (down) 0
39 OFF 0
UP 0
DWN (down) Battery voltage
PIIA4804E
Revision: December 20092009 QX56

TILT MOTORADP-99
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Is the inspection result normal?
YES >> Replace tilt motor assembly. Refer to ST-19, "Removal and Installation".
NO >> GO TO 3
3. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "Intermittent Incident"
.
Is the inspection result normal?
YES >> Replace automatic drive posit ioner control unit. Refer to ADP-166, "Removal and Installation".
NO >> Repair or replace the malfunctioning part.
Connector Te r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (-)
M34 35
Ground ADP steering switch ON
(UP operation)
Battery voltage
Other than above 0
42 ADP steering switch ON
(DOWN operation)
Battery voltage
Other than above 0
Revision: December 20092009 QX56

ADP-100
< COMPONENT DIAGNOSIS >
PEDAL ADJUSTING MOTOR
PEDAL ADJUSTING MOTOR
DescriptionINFOID:0000000003775636
 The pedal adjusting motor is installed to the pedal assembly.
 The pedal adjusting motor is activated with the automatic drive positioner control unit.
 The pedal assembly is adjusted forward/backward by changing the rotation direction of pedal adjustingmotor.
Component Function CheckINFOID:0000000003775637
1. CHECK FUNCTION
1. Select “ADJ PEDAL MOTOR” in “Active test” mode with CONSULT-III.
2. Check the pedal adjusting motor operation.
Is the operation of relevant parts normal?
YES >> Inspection End.
NO >> Perform diagnosis procedure. Refer to ADP-100, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000003775638
1. CHECK PEDAL ADJUSTING MOTOR POWER SUPPLY
1. Turn the ignition switch OFF.
2. Perform “Active test” (“ADJ PEDAL MOTOR”) with CONSULT-lll.
3. Check voltage between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace pedal adjusting motor assembly. Refer to ADP-169, "Removal and Installation".
NO >> GO TO 2
2. CHECK PEDAL ADJUSTING MOTOR CIRCUIT
Test item Description
ADJ PEDAL MOTOR OFF
Pedal adjusting motor Sto p
FR Forward
RR Backward
Te r m i n a l
Test ItemVoltage
(V)
(Approx.)
(+)
(-)
Automatic
drive posi-
tioner con- trol unit
connector Te r m i n a l
M34 37
Ground ADJ PED-
AL MOTOR OFF 0
RR (backward) 0
FR (forward)
Battery
voltage
45 OFF 0
RR (backward)
Battery
voltage
FR (forward) 0
PIIA4806E
Revision: December 20092009 QX56

ADP-102
< COMPONENT DIAGNOSIS >
DOOR MIRROR MOTOR
DOOR MIRROR MOTOR
DescriptionINFOID:0000000003775639
It makes mirror face operate from side to side and up and down with the electric power that automatic drive
positioner control unit supplies.
Component Function CheckINFOID:0000000003775640
1. CHECK DOOR MIRROR MOTOR FUNCTION
Check the operation with “MIRROR MOTOR RH” and “MI RROR MOTOR LH” in “ACTIVE TEST” mode with
CONSULT-III
Refer to ADP-28, "CONSULT-III Function"
.
Is the inspection result normal?
YES >> Door mirror motor function is OK.
NO >> Refer to ADP-102, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000003775641
1. CHECK DOOR MIRROR MOTOR INPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between door mirror connector and ground.
Is the inspection result normal?
YES >> Refer to ADP-104, "Component Inspection".
NO >> GO TO 2
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect automatic drive posit ioner control unit and door mir-
ror.
3. Check continuity between automat ic drive positioner control unit
connector and door mirror connector.
Door mirror LH
Te r m i n a l s
Door mirror re-
mote control
switch condition Voltage (V)
(Approx.)
(+)
(–)
Door mirror
connector Te r m i n a l
D4 (LH)
D107 (RH) 1
Ground UP Battery voltage
Other than above 0
2 LEFT Battery voltage
Other than above 0
3 DOWN / RIGHT Battery voltage
Other than above 0
ALJIA0196ZZ
Automatic drive
positioner control unit connector Te r m i n a l
Door mirror LH
connector Terminal Continuity
M33 16
D4 3
Ye s
31 1
32 2
LIIA1880E
Revision: December 20092009 QX56

DOOR MIRROR MOTORADP-103
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Door mirror RH
4. Check continuity between automat ic drive positioner control unit
connector and ground.
Door mirror LH
Door mirror RH
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK AUTOMATIC DRIVE POSITION ER CONTROL UNIT OUTPUT SIGNAL
1. Connect automatic drive positioner control unit.
2. Turn ignition switch ON.
3. Check voltage between automatic drive positioner control unit
connector and ground.
Door mirror LH
Automatic drive posi-
tioner control unit con- nector Te r m i n a l
Door mirror
RH connector Terminal Continuity
M33 14
D107 1
Ye s
15 2
30 3
Automatic drive position- er control unit connector Te r m i n a l
GroundContinuity
M33 16
No
31
32
Automatic drive position- er control unit connector Te r m i n a l
GroundContinuity
M33 14
No
15
30
LIIA1888E
Te r m i n a l s
Mirror switch condition Voltage (V)
(Approx.)
(+)
(-)
Automatic drive
positioner control unit connector Te r m i n a l
M33 16
Ground DOWN / RIGHT Battery voltage
Other than above 0
31 UP Battery voltage
Other than above 0
32 LEFT Battery voltage
Other than above 0
ALJIA0197ZZ
Revision: December 20092009 QX56