ignition INFINITI QX56 2010 Factory Service Manual

DEF-44
< PRECAUTION >
PRECAUTIONS
5. When the repair work is completed, return the ignition switch to the ″LOCK ″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of a ll control units using CONSULT-III.
Handling for Adhesive and PrimerINFOID:0000000005146856
• Do not use an adhesive which is past its usable date. Shel f life of this product is limited to six months after
the date of manufacture. Carefully adhere to the expiration or manufacture date printed on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Open the seal of the primer and adhesive just before application. Discard the remainder.
• Before application, be sure to shake the primer container to stir the contents. If any floating material is found, do not use it.
• If any primer or adhesive contacts the skin, wipe it off with gasoline or equivalent and wash the skin with
soap.
• When using primer and adhesive, always observe the precautions in the instruction manual.
Revision: April 20092010 QX56

DLK-3
C
DE
F
G H
I
J
L
M A
B
DLK
N
O P
REAR LH ...............................................................
....
88
REAR LH : Description ............................................88
REAR LH : Component Function Check ...............88
REAR LH : Diagnosis Procedure ............................88
REAR RH ............................................................... ....89
REAR RH : Description ...........................................90
REAR RH : Component Function Check ...............90
REAR RH : Diagnosis Procedure ............................90
BACK DOOR ......................................................... ....91
BACK DOOR : Description ......................................91
GLASS HATCH LOCK ACTUATOR ..................92
Diagnosis Procedure ...............................................92
PASSENGER SELECT UNLOCK RELAY .........93
Description .......................................................... ....93
Component Function Check ....................................93
Diagnosis Procedure ...............................................93
INTELLIGENT KEY WARNING BUZZER ..........95
Description .......................................................... ....95
Component Function Check ..................................95
Diagnosis Procedure ...............................................95
Component Inspection ............................................96
OUTSIDE KEY ANTENNA .................................97
Description .......................................................... ....97
Component Function Check ..................................97
Diagnosis Procedure ...............................................97
STEERING LOCK UNIT .....................................99
Diagnosis Procedure ........................................... ....99
A/T SHIFT SELECTOR (PARK POSITION
SWITCH) ...........................................................
101
Diagnosis Procedure ........................................... ..101
REMOTE KEYLESS ENTRY RECEIVER ........103
Description .......................................................... ..103
Component Function Check ................................103
Diagnosis Procedure .............................................103
INTELLIGENT KEY BATTERY AND FUNC-
TION .................................................................
106
Description .......................................................... ..106
Component Function Check ................................106
Diagnosis Procedure .............................................106
HORN FUNCTION ............................................108
Description .......................................................... ..108
Component Function Check ................................108
Diagnosis Procedure ............................................108
COMBINATION METER DISPLAY FUNC-
TION .................................................................
110
Description .......................................................... ..110
Component Function Check ................................110
Diagnosis Procedure .............................................110
WARNING CHIME FUNCTION ........................111
Description ........................................................... ..111
Component Function Check ................................111
Diagnosis Procedure .............................................111
HAZARD FUNCTION ......................................112
Description .............................................................112
Component Function Check ................................112
Diagnosis Procedure .............................................112
KEY SWITCH (INTELLIGENT KEY UNIT IN-
PUT) ................................................................
113
Diagnosis Procedure .............................................113
KEY SWITCH (BCM INPUT) ...........................115
Diagnosis Procedure .............................................115
IGNITION KNOB SWITCH ..............................116
Diagnosis Procedure .............................................116
HEADLAMP FUNCTION .................................118
Diagnosis Procedure .............................................118
MAP LAMP AND IGNITION KEYHOLE ILLU-
MINATION FUNCTION ...................................
119
Diagnosis Procedure .............................................119
KEYFOB ID SET UP WITH CONSULT-III ......120
ID Code Entry Procedure ......................................120
KEYFOB ID SET UP WITHOUT CONSULT-III .121
ID Code Entry Procedure .................................... ..121
AUTOMATIC BACK DOOR SELF-DIAGNO-
SIS PROCEDURE ...........................................
123
Self-Diagnosis Procedure ......................................123
POWER LIFTGATE SWITCH FUNCTION ......125
Diagnosis Procedure ........................................... ..125
GLASS HATCH SWITCH ................................127
Diagnosis Procedure .............................................127
GLASS HATCH AJAR SWITCH .....................129
Diagnosis Procedure .............................................129
BACK DOOR CLOSE (CLOSE) SWITCH
SYSTEM ..........................................................
131
Diagnosis Procedure ........................................... ..131
BACK DOOR CLOSE (CANCEL) SWITCH
SYSTEM ..........................................................
133
Diagnosis Procedure ........................................... ..133
PINCH STRIP SYSTEM ..................................135
Diagnosis Procedure .............................................135
BACK DOOR WARNING CHIME SYSTEM ....136
Diagnosis Procedure .............................................136
HALF-LATCH SWITCH SYSTEM ...................137
Diagnosis Procedure .............................................137
BACK DOOR OPEN SWITCH SYSTEM ........138
Revision: April 20092010 QX56

DLK-10
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
AUTOMATIC DOOR LOCKS
FUNCTION DIAGNOSIS
AUTOMATIC DOOR LOCKS
System DiagramINFOID:0000000005146867
System DescriptionINFOID:0000000005146868
DOOR LOCK FUNCTION
• The door lock and unlock switch (driver side) is built into power window main switch.
• The door lock and unlock switch (passenger side) is on door trim.
• Interlocked with the locking operation of door lock and
unlock switch, door lock actuators of all doors are
locked.
• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors are
unlocked.
Door Key Cylinder
• With the door key inserted in the door key cylinder on driver side, turning it to “LOCK”, will lock door lock
actuator of all doors.
• With the door key inserted in the door key cylinder on driver side, turning it to “UNLOCK” onc\
e unlocks the driver side door lock actuator; turning it to “UNLOCK” again within 5 seconds after the first unlock operation
unlocks all of the other doors. - (SELECTIVE UNLOCK OPERATION)
Selective unlock operation mode can be changed usi ng “DOOR LOCK-UNLOCK SET” mode in “WORK SUP-
PORT”. Refer to DLK-53, "
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)".
AUTOMATIC DOOR LOCKS (LOCK OPERATION)
The interlock door lock function is the function that locks all doors linked with the vehicle speed.
Vehicle Speed Sensing Auto Door Lock*1
All doors are locked when the vehicle speed reaches 24 km/h (15 MPH) or more.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is turned ON, all
doors are closed and the vehicle speed received from the combination meter via CAN communication
becomes 15 MPH (24 km/h) or more.
ALKIA1482GB
Input SingleFunction Actuator
Door lock/unlock switch Door lock/unlock signal Door lock function
Each door lock actuator
Door key cylinder switch
Each door switch
Door open/close signal
Key reminder function
Combination meter Warning buzzer signal
Vehicle speed signal
Automatic door lock/unlock
function
TCM Shift position signal
Revision: April 20092010 QX56

AUTOMATIC DOOR LOCKSDLK-11
< FUNCTION DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
If a door is opened and closed at any time during one ignition cycle (O\
FF → ON), even after initial auto door
lock has taken place, the BCM will relock all doors when the vehicle speed reaches 15 MPH (24 km/h) or more
again.
Setting change of Automatic Door Locks (LOCK) Function
The lock operation setting of the aut omatic door locks function can be changed.
With CONSULT-III
The ON/OFF switching of the automatic door locks (LOCK) function and the type selection of the automatic
door locks (LOCK) function can be performed at the WO RK SUPPORT setting of CONSULT-III. Refer to DLK-
53, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)".
Without CONSULT- III
The automatic door locks (LOCK) function can be swit ched ON/OFF by performing the following operation.
1. Close all doors (door switch OFF).
2. Turn ignition switch ON.
3. Within 20 seconds of turning the ignition switch ON, press and hold the door lock and unlock switch to the LOCK position for more than 5 seconds.
4. The switching is completed when the hazard lamps blink.
5. The ignition switch must be turned OFF and ON again between each setting change.
AUTOMATIC DOOR LOCKS (UNLOCK OPERATION)
The automatic door locks (UNLOCK) function is the function that unlocks all doors linked with the key position.
IGN OFF Interlock Door Unlock*1
All doors are unlocked when the power supply position is changed from ON to OFF.
BCM outputs the unlock signal to all door lock actuator s when it detects that the power supply position is
changed from ignition switch ON to OFF.
Setting change of Automatic Door Locks (UNLOCK) Function
The lock operation setting of the aut omatic door locks function can be changed.
With CONSULT-III
The ON/OFF switching of the automatic door locks (UNL OCK) function and the type selection of the automatic
door locks (UNLOCK) function can be performed at the WORK SUPPORT setting of CONSULT-III. Refer to
DLK-53, "
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)".
Without CONSULT- III
The automatic door locks (UNLOCK) function can be sw itched ON/OFF by performing the following operation.
1. Close all doors (door switch OFF).
2. Turn ignition switch ON.
3. Within 20 seconds of turning the ignition switch ON, press and hold the door lock and unlock switch to the UNLOCK position for more than 5 seconds.
4. The switching is completed when the hazard lamps blink.
5. The ignition switch must be turned OFF and ON again between each setting change.
*1: This function is set to ON before delivery.
OFF → ON : 2 blinks
ON → OFF : 1 blink
OFF → ON : 2 blinks
ON → OFF : 1 blink
Revision: April 20092010 QX56

DLK-12
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
AUTOMATIC DOOR LOCKS
Component Parts Location
INFOID:0000000005146869
Component DescriptionINFOID:0000000005146870
ALKIA1835ZZ
1. Key switch and ignition knob switch M12 2. BCM M18, M19, M20 3. Combination meter M24
4. TCM F9 5. Front door lock assembly LH (key cyl-
inder switch) D14
Front door lock assembly RH D114 6. Main power window and door lock/
unlock switch D7, D8
7. Front door switch LH B8 RH B108 8. Rear door switch LH B18
RH B116 9. Back door latch (door ajar switch)
D503
10. Rear door lock actuator LH D205 RH D305 11. Glass hatch lock actuator D711 12. Back door and glass hatch switch
assembly (glass hatch switch) D706
Item Function
BCM Controls the door lock function and room lamp function.
Door lock and unlock switch Input lock or unlock signal to BCM.
Revision: April 20092010 QX56

DOOR LOCK FUNCTIONDLK-15
< FUNCTION DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
DOOR LOCK AND UNLOCK SWITCH : Component Parts LocationINFOID:0000000005146873
DOOR LOCK AND UNLOCK SWITCH : Component DescriptionINFOID:0000000005146874
1. Key switch and ignition knob switch M12 2. BCM M18, M19, M20 (view with instrument panel removed)3. Front door lock assembly LH (key
cylinder switch) D14
Front door lock actuator RH D114
4. Main power window and door lock/un- lock switch D7, D8 5. Front door switch
LH B8
RH B108 6. Rear door switch
LH B18
RH B116
7. Power window and door lock/unlock switch RH D105 8. Back door latch (door ajar switch)
D503 9. Rear door lock actuator
LH D205
RH D305
10. Passenger select unlock relay M7 (view with instrument panel LH removed) 11. Glass hatch lock actuator D711 12. Back door and glass hatch switch
assembly (glass hatch switch) D706
ALKIA1836ZZ
Item Function
BCM Controls the door lock function and room lamp function.
Door lock and unlock switch Transmits lock or unlock signal to BCM.
Door lock actuator Receives lock/unlock signal from BCM and locks/unlocks each door.
Revision: April 20092010 QX56

DOOR LOCK FUNCTIONDLK-17
< FUNCTION DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
*: Even with a registered Intelligent Key remaining inside the vehicle, door locks can be unlocked from outside of the vehicle with a spare
Intelligent Key as long as key IDs are different.
OUTSIDE KEY ANTENNA DETECTION AREA
The outside key antenna detection area of door lock/unlock function
is in the range of approximately 80 cm (31.50 in) surrounding the
driver and passenger door handles (1).
OUTSIDE KEY ANTENNA DETECTION AREA
The outside key antenna detection area of back door lock/unlock
function is in the range of approximately 80 cm (31.50 in) surround-
ing the back door handle (1).
SELECTIVE UNLOCK FUNCTION
When a LOCK signal is sent from door request switch (driver side or passenger side), all doors will be locked.
When an UNLOCK signal is sent from door request switch (driver side or passenger side) once, driver's door
will be unlocked.
Then, if an UNLOCK signal is sent from door request switch (driver side and passenger side) again within 5
seconds, all other doors will be unlocked.
HAZARD AND BUZZER REMINDER FUNCTION
During lock or unlock operation by each request switch, the hazard warning lamps and Intelligent Key warning
buzzer will blink or honk as a reminder.
When doors are locked, unlocked by each request switch, IPDM E/R honks Intelligent Key warning buzzer as
a reminder and transmits hazard request signal to BCM via CAN communication line.
BCM flashes hazard warning lamps as a reminder.
Operating function of hazard warning lamps and buzzer reminder
How to change hazard and buzzer reminder mode
Refer to DLK-55, "
INTELLIGENT KEY : CONSULT-III F unction (BCM - INTELLIGENT KEY)".
AUTO DOOR LOCK FUNCTION
Each request switch operation Operation condition
Lock operation • All doors are closed
• Ignition switch is in OFF position
• Intelligent Key is outside the vehicle
• Intelligent Key is within outside key antenna detection area
Unlock Operation • Intelligent Key is outside the vehicle
• Intelligent Key is within outside key antenna detection area *
ALKIA0582ZZ
ALKIA0581ZZ
Operation
Hazard warning lamps flash Intelligent Key warning buzzer sounds
Unlock OnceOnce
Lock Twice Twice
Back door open —Four times
Revision: April 20092010 QX56

DLK-18
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK FUNCTION
When all doors are locked, ignition switch is in OFF
position and key switch is OFF, doors are unlocked with
door request switch
When BCM does not receive the following signals within 60 seconds, all doors are locked.
• Door switch is ON (door is opened)
• Door is locked
• Ignition switch is ON (ignition switch is pressed)
• Key switch is ON
Auto door lock mode can be changed by “AUTO LOCK SET” mode in “WORK SUPPORT”. Refer to DLK-55,
"INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)".
ROOM LAMP OPERATION
When the following conditions are met:
• Condition of interior lamp switch is in DOOR position
• Door switch OFF (all the doors are closed)
Intelligent Key system turns on interior lamp (for up to 30 seconds maximum) by receiving UNLOCK signal
from door request switch. For detailed description, refer to DLK-14, "
DOOR LOCK AND UNLOCK SWITCH :
System Description".
LIST OF OPERATION RELATED PARTS
Parts marked with × are the parts related to operation.
Door lock function
Intelligent Key
Ignition key switch
Remote keyless entry receiver
Door switch
Door request switch (Driver, Passenger)
Door lock actuator
Inside key antenna
Outside key antenna (Driver, Passenger)
Intelligent Key warning buzzer
CAN communication system
BCM
Hazard warning lamp
Door lock/unlock function by request switch ×××××××× ××
Hazard and buzzer reminder function for door lock/unlock
operation ××××
Key reminder function ××××××××××××
Selective unlock function by request switch
(Driver side) ×
×××× ××
Selective unlock function by request switch
(Passenger side) ×
×××× ××
Auto door lock function ×× ×××××
Revision: April 20092010 QX56

DLK-20
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK FUNCTION
ALKIA0579ZZ
1. Horn E3
(view with hood open) 2. IPDM E/R E122, E124
(view with cover removed) 3. Horn relay H-1
4. Remote keyless entry receiver M25 (view with instrume nt panel RH removed) 5. Intelligent key warning buzzer E25 6. Combination meter M23, M24
7. Intelligent Key unit M70 (view with instrument panel LH removed) 8. BCM M18, M19, M20
(view with instrument panel LH removed) 9. Steering lock solenoid M15
(view with steering column removed)
10. Key switch and ignition knob switch M12 11. A/T shift selector (park position switch) M203
(view with center console removed)12. Center console area antenna (front)
M210
(view with center console removed)
13. Center console area antenna (rear) M209 14. Overhead console area antenna R210
(view with overhead console removed) 15. Luggage area antenna B76
(view with rear carpet removed)
16. Rear bumper antenna C7 (view with rear bumper removed) 17. Back door latch D503
18. Front outside antenna LH D15
Front outside antenna RH D115
19. Front door request switch LH D16 Front door request switch RH D116 20. Front door lock assembly LH (door un-
lock sensor) D14 21. Front door switch LH B8
RH B108
22. Rear door switch LH B18 RH B116
Revision: April 20092010 QX56

DOOR LOCK FUNCTIONDLK-21
< FUNCTION DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
DOOR REQUEST SWITCH : Component DescriptionINFOID:0000000005146878
INTELLIGENT KEY
INTELLIGENT KEY : System DiagramINFOID:0000000005146879
INTELLIGENT KEY : System DescriptionINFOID:0000000005146880
The Intelligent Key has the same functions as the remote control entry system. In addition to other safety fea-
tures, it can be used to lock and unlock all doors as well as open the back door.
OPERATION DESCRIPTION/DOOR LOCK/UNLOCK FUNCTION
• When door lock/unlock button of the Intelligent Key is pressed, lock signal or unlock signal is transmitted from Intelligent Key to BCM via remote keyless entry receiver and Intelligent Key unit.
• When BCM receives the door lock/unlock signal, it oper ates door lock actuator, flashes the hazard lamp
(lock: 2 times, unlock: 1 time) and horn chirp signal to IPDM E/R at the same time as a reminder.
• IPDM E/R honks horn (lock: 2 times) as a reminder
OPERATION CONDITION
OPERATION AREA
• Operating Range
Item Function
Intelligent Key unit Receives lock/unlock signal from re mote keyless entry receiver, and then transmits to BCM.
BCM Controls the door lock function and room lamp function.
Door lock and unlock switch Transmits lock or unlock signal to BCM.
Door lock actuator Receives lock/unlock signal from BCM and locks/unlocks each door.
Door switch Transmits door open/close condition to BCM.
Remote keyless entry receiver Receives lock/unlock signal from the Intelligent Key, and then transmits to Intelligent Key unit.
Request switch Transmits lock/unlock operation to Intelligent Key unit.
Intelligent Key Transmits button operation to remote keyless entry receiver.
Outside key antenna Detects if Intelligent Key is outside the vehicle.
Inside key antenna Detects if Intelligent Key is inside the vehicle.
Intelligent Key warning buzzer Warns the user of the lock/unlock condition and inappropriate operations with the buzzer sound.
ALKIA0704GB
Remote controller operation Operation conditionOperation
Lock • All doors closed All doors lock
Unlock • Intelligent Key is out of the ignition key cylinder All doors unlock
Revision: April 20092010 QX56