remove seats INFINITI QX56 2011 Factory User Guide

FRONT SEATSE-117
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
Install the hog rings of seat cushion trim in positi on, and then securely connect the trim or trim cord
with the pad side wire.
CLIMATE CONTROLLED SEAT UNIT
CLIMATE CONTROLLED SEAT UNI T : Disassembly and AssemblyINFOID:0000000006217427
DISASSEMBLY
1. Remove the seatback thermal electric unit and seatback blower
motor.
 Disconnect the harness connectors (A).
 Remove the screws (B).
2. Remove the seatback climate controlled seat duct finisher.
3. Remove the seat cushion thermal electric unit and seat cushion blower motor.
 Disconnect the harness connectors (A), and then remove the harness clamp.
 Remove the screws (B).
4. Remove the seat cushion climat e controlled seat duct finisher.
5. Remove the climate controlled seat control unit.  Disconnect the harness connectors (A).
 Remove the screws (B).
ASSEMBLY
Assemble in the reverse order of disassembly.
HEADREST (WITH HEAD REST DISPLAY ONLY)
HEADREST (WITH HEADREST DISPLAY ONLY) : Disassembly and Assembly
INFOID:0000000006217428
DISASSEMBLY
JMJIA4058ZZ
JMJIA4059ZZ
JMJIA4060ZZ
Revision: 2010 May2011 QX56

FRONT SEATSE-119
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
4. Pull downward and remove headrest display escutcheon (1) and headrest display unit (2) by pulling them out and remov-
ing pins on upper side of display.
5. Disconnect inner harness connector.
6. Remove headrest display escutcheon from headrest display unit. Press headrest display escutcheon to the headrest display unit side. Disconnect pawls on upper side
and remove headrest display escutcheon.
4. Remove the headrest display harness upper tube from headrest trim.
5. Remove the headrest trim from headrest pad and frame.
ASSEMBLY
Assembly in the reverse order of disassembly.
JMJIA4233ZZ
Revision: 2010 May2011 QX56

SECOND SEATSE-125
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
Removal and InstallationINFOID:0000000006217430
REMOVAL
CAUTION:
 When removing and installing, use shop cloths to protect parts from damage.
 When removing and installing, 2 workers ar e required so as to prevent it from dropping.
1. Remove the headrest.
2. Remove the seat hinge cover.
a. Bench seat (RH side) and captain seat  Open pawls on upper side to outside and disconnect thepawls.
 Pull the cover forward, side the pawl on lower side downward, and disconnect the pawl.
b. Bench seat (LH side)  Open pawls on upper side to outside and disconnect thepawls.
 Pull the cover forward, side the pawl on lower side downward,
and disconnect the pawl.
3. Remove the from mounting bolt of seat hinge assembly.
4. Operate rear seat lever or reclining lever to releas e seat lock assembly lock and to fold seat forward.
5. Disconnect seat harness assembly harness connector (A).
6. Remove the rear mounting nut of seat hinge assembly.
19. Reclining device outer cover (inside) 20. Reclining device outer cover (out- side)21. Snap ring
22. Reclining lever knob 23. Seatback board 24. Seatback board clip
25. Seatback heater unit 26. Rear seat lever assembly 27. Seat control lever escutcheon
28. Seatback frame 29. Reclining device inner cover (out- side)30. Bush
31. Seat cushion frame : Pawl
Refer to GI-4, "
Components" for symbols in the figure.
: Pawl
JMJIA3870ZZ
: Pawl
JMJIA3869ZZ
JMJIA4261ZZ
Revision: 2010 May2011 QX56

SECOND SEATSE-127
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
(heater seat model only)
5. Remove the rear seat lever assembly. 1. Remove the rear seat lever assembly fixing screws.
2. Lift rear seat lever assembly and remove seatback control wire.
6. Remove the seatback center finisher. 1. Pull seatback center finisher cover rearward to remove.
2. Remove the seatback center finisher fixing screws.
3. Remove the seat belt from seatback center finisher.
7. Remove the center seat belt anchor. 1. Remove the seat cushion and seat cushion under cover.
Refer to SE-130, "
SEAT CUSHION : Disassembly and Assembly".
2. Remove the center seat belt anchor. Refer to SB-13, "
SEAT BELT RETRACTOR : Removal and Installation".
8. Remove the seatback trim and seatback pad. 1. Remove the headrest holder. CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
JMJIA4471ZZ
: Pawl
JMJIA3877ZZ
PIIB4084J
Revision: 2010 May2011 QX56

SECOND SEATSE-129
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
1. Slide and align the clips (B) to the holes on the seatback as shown in the figure, and then remove the seatback board
(A).
2. Remove the clips after removing the seatback board.
3. Disconnect the seatback heater unit harness connector (A).
(heater seat model only)
4. Remove the rear seat lever assembly. 1. Remove the rear seat lever assembly fixing screws.
2. Lift rear seat lever assembly and remove seatback control wire.
5. Remove the seatback trim and seatback pad. 1. Remove the headrest holder. CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
2. Roll up seatback trim (2) from backward to forward so that seat control lever escutcheon (1) is visible.
3. Remove the seat control lever escutcheon (1).
4. Remove the seatback trim and seat back pad from the seatback frame.
5. Remove the hog rings, and separate the seatback trim and seatback pad.
6. Remove the seatback frame.
JMJIA4076ZZ
JMJIA4262ZZ
PIIB4084J
: Pawl
JMJIA3878ZZ
Revision: 2010 May2011 QX56

SECOND SEATSE-131
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
3. Remove the reclining device outer cover (outside) Pull reclining device outer cover forward and disengage pawls.
4. Remove the fixing screw and then remove seat cushion under cover.
5. Remove the reclining device outer cover (inside).
6. Remove the center seat belt anchor. Refer to SB-13, "
SEAT BELT RETRACTOR : Removal and Installa-
tion".
7. Remove the seatback trim and seatback pad. Refer to SE-126, "
SEATBACK : Disassembly and Assem-
bly".
8. Remove the device arm cover.
9. Remove the reclining device inner cover (outside) (1) and reclin- ing device inner cover (inside) (2).
10. Remove the seat cushion frame. 1. Remove the seatback control wire (A) and seat cushion control wire (B).
2. Remove seatback control wire installed to seat cushion frame.
3. Remove the mounting bolts and then remove seat cushion frame.
11. Remove the seat cushion hinge cover
: Pawl
JMJIA3882ZZ
: Pawl
JMJIA3887ZZ
JMJIA3886ZZ
Revision: 2010 May2011 QX56

SECOND SEATSE-133
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
5. Remove the seat cushion frame. 1. Remove the fixing screw and then remove seat cushion under cover.
2. Remove the seatback control wire (A) and seat cushion control wire (B).
3. Remove the seatback control wire installed to seat cushion frame.
4. Remove the mounting bolts and then remove seat cushion frame.
6. Remove the seat belt buckle. Refer to SB-16, "
SEAT BELT BUCKLE : Removal and Installation".
7. Remove the seat cushion carpet.
8. Remove the seat cushion hinge cover  Disengage pawls on front side of seat cushion hinge cover.
 Disengage pawls on rear side of seat cushion hinge cover.
9. Remove the mounting bolts and then remove seat hinge assembly.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
 Install the hog rings of seat trim in position, and then securely connect the trim or trim cord with the
seat frame.
 Adjust the cable when installing the seatb ack control wire and seat cushion control wire.
Refer to SE-134, "
Adjustment".
ARMREST
ARMREST : Disassembly and AssemblyINFOID:0000000006217433
DISASSEMBLY
1. Remove the mounting bolts. Remove the armrest out er bracket and the armrest inner cover RH from the
armrest assembly.
2. Remove the fixing screws of the cup holder. Remove the cup holder from the armrest assembly.
JMJIA3886ZZ
: Pawl
JMJIA3883ZZ
Revision: 2010 May2011 QX56

THIRD SEATSE-139
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
SE
N
O P
Install in the reverse order of removal.
Disassembly and AssemblyINFOID:0000000006217437
SEATBACK
Disassembly
1. Remove the hinge cover. 1. Remove the seat cushion trim and seat cushion pad from seat cushion frame.
2. Remove the fixing screws, and then remove the hinge cover.
2. Remove the mounting bolts, and then remove the seatback assembly.
3. Open fastener (A) of seatback trim. LH side
 RH side
4. Remove clips that retain seatback board and seatback trim.
5. Remove the seatback board and the clips. 1. Slide and align the clips (B) to the holes on the seatback board (A) as shown in the figure, and then remove the seat-
back board (A).
2. Remove the clips after removing the seatback board.
6. Remove the seatback trim and seatback pad.
JMJIA4328ZZ
JMJIA4329ZZ
JMJIA4076ZZ
Revision: 2010 May2011 QX56