engine INFINITI QX80 2023 Owners Manual

9-16Maintenance and schedules
85,000 Miles/102 Months/
136,000 Km
Perform at number of miles, kilometers or months,
whichever comes first.
Standard maintenance:
Not Applicable. Proceed to next interval.
Severe use maintenance:
Inspections:
.Brake pads and rotors.Steering gear and linkage.Axle and suspension parts.Propeller shaft (4WD models).Drive shaft boots (4WD models).Exhaust system
Essentials:
.Replace engine oil and filter
90,000 Miles/72 Months/144,000
Km
Perform at number of miles, kilometers or months,
whichever comes first.
Standard maintenance:
Inspections:
.Brake lines and cables.Brake pads and rotors.Engine drive belts.Fuel tank vapor vent system hoses.Fuel lines/connections.Exhaust system.Propeller shaft (4WD models).Steering gear and linkage.Axle and suspension parts.Differential gear oil.Transfer case oil (4WD models).Drive shaft boots (4WD models)
Essentials:
.Replace engine air filter (1).Replace brake fluid.Replace engine oil and filter.Replace in-cabin microfilter.Replace Intelligent Key battery.Tire rotation.Lubricate propeller shaft grease (4WD models)
Severe use maintenance:
Not Applicable. Proceed to next interval.
(1) If operating mainly in dusty conditions, more
frequent maintenance may be required.
90,000 Miles/108 Months/
144,000 Km
Perform at number of miles, kilometers or months,
whichever comes first.
Standard maintenance:
Not Applicable. Proceed to next interval.
Severe use maintenance:
Inspections:
.Brake pads and rotors.Steering gear and linkage.Axle and suspension parts.Propeller shaft (4WD models).Drive shaft boots (4WD models).Exhaust system
Essentials:
.Replace engine oil and filter.Replace brake fluid

95,000 Miles/114 Months/
152,000 Km
Perform at number of miles, kilometers or months,
whichever comes first.
Standard maintenance:
Not Applicable. Proceed to next interval.
Severe use maintenance:
Inspections:
.Brake pads and rotors.Steering gear and linkage.Axle and suspension parts.Propeller shaft (4WD models).Drive shaft boots (4WD models).Exhaust system
Essentials:
.Replace engine oil and filter
97,500 Miles/78 Months/156,000
Km
Perform at number of miles, kilometers or months,
whichever comes first.
Standard maintenance:
Essentials:
.Replace engine oil and filter.Tire rotation
Severe use maintenance:
Not Applicable. Proceed to next interval.
100,000 Miles/120 Months/
160,000 Km
Perform at number of miles, kilometers or months,
whichever comes first.
Standard maintenance:
Not Applicable. Proceed to next interval.
Severe use maintenance:
Inspections:
.Brake pads and rotors.Steering gear and linkage.Axle and suspension parts.Propeller shaft (4WD models).Drive shaft boots (4WD models).Exhaust system
Essentials:
.Replace engine oil and filter.Replace brake fluid.Replace differential gear oil.Replace transfer case oil (4WD models)
Maintenance and schedules9-17

9-18Maintenance and schedules
105,000 Miles/84 Months/
168,000 Km
Perform at number of miles, kilometers or months,
whichever comes first.
Standard maintenance:
Inspections:
.Brake lines and cables.Brake pads and rotors.Engine drive belts.Propeller shaft (4WD models).Differential gear oil.Transfer case oil (4WD models).Drive shaft boots (4WD models)
Essentials:
.Replace engine coolant (1).Replace engine oil and filter.Replace in-cabin microfilter.Replace spark plugs (2) (3).Lubricate propeller shaft grease (4WD models).Tire rotation
Severe use maintenance:
Not Applicable. Proceed to next interval. (1) First replacement interval is 105,000 miles
(168,000 km) or 84 months. After first replace-
ment, replace every 75,000 miles (120,000 km)
or 60 months.
Engine Coolant service note: "Use only Genuine
NISSAN Long Life Antifreeze/Coolant (blue) or
equivalent with proper mixture ratio of 50%
antifreeze and 50% demineralized or distilled
water. Mixing any other type of coolant or the use
of non-distilled water may reduce the life ex-
pectancy of the factory fill coolant."
(2) Performed based on the number of miles only.
(3) Replace spark plug when the plug gap exceeds
0.053 in (1.35 mm) even if within specified
replacement mileage.
105,000 Miles/126 Months/
168,000 Km
Perform at number of miles, kilometers or months,
whichever comes first.
Standard maintenance:
Not Applicable. Proceed to next interval.
Severe use maintenance:
Inspections:
.Brake pads and rotors.Steering gear and linkage.Axle and suspension parts.Propeller shaft (4WD models).Drive shaft boots (4WD models).Exhaust system
Essentials:
.Replace engine oil and filter

110,000 Miles/132 Months/
176,000 Km
Perform at number of miles, kilometers or months,
whichever comes first.
Standard maintenance:
Not Applicable. Proceed to next interval.
Severe use maintenance:
Inspections:
.Brake pads and rotors.Steering gear and linkage.Axle and suspension parts.Propeller shaft (4WD models).Drive shaft boots (4WD models).Exhaust system
Essentials:
.Replace engine oil and filter.Replace brake fluid
112,500 Miles/90 Months/
180,000 Km
Perform at number of miles, kilometers or months,
whichever comes first.
Standard maintenance:
Essentials:
.Replace engine oil and filter.Replace Intelligent Key battery.Tire rotation
Severe use maintenance:
Not Applicable. Proceed to next interval.
115,000 Miles/138 Months/
184,000 Km
Perform at number of miles, kilometers or months,
whichever comes first.
Standard maintenance:
Not Applicable. Proceed to next interval.
Severe use maintenance:
Inspections:
.Brake pads and rotors.Steering gear and linkage.Axle and suspension parts.Propeller shaft (4WD models).Drive shaft boots (4WD models).Exhaust system
Essentials:
.Replace engine oil and filter
Maintenance and schedules9-19

9-20Maintenance and schedules
120,000 Miles/96 Months/
192,000 Km
Perform at number of miles, kilometers or months,
whichever comes first.
Standard maintenance:
Inspections:
.Brake lines and cables.Brake pads and rotors.Engine drive belts.Fuel tank vapor vent system hoses.Fuel lines/connections.Exhaust system.Propeller shaft (4WD models).Steering gear and linkage.Axle and suspension parts.Differential gear oil.Transfer case oil (4WD models).Drive shaft boots (4WD models)
Essentials:
.Replace engine air filter (1).Replace brake fluid.Replace engine oil and filter.Replace in-cabin microfilter.Tire rotation.Lubricate propeller shaft grease (4WD models)
Severe use maintenance:
Not Applicable. Proceed to next interval.
(1) If operating mainly in dusty conditions, more
frequent maintenance may be required.

ADDITIONAL INFORMATION
NOTE FOR ENGINE COOLANT *:
(1) First replacement interval is 105,000 miles
(168,000 km) or 84 months. After first repla-
cement, replace every 75,000 miles (120,000
km) or 60 months.
* Maintenance items and intervals with “ * ” are
recommended by INFINITI for reliable vehicle
operation. The owner need not perform such
maintenance in order to maintain the emission
warranty or manufacturer recall liability. Other
maintenance items and intervals are required.
NOTE FOR SPARK PLUGS:
(1) Replace every 105,000 miles (168,000 km)
(2) Replace spark plug when the plug gap
exceeds 0.053 in (1.35 mm) even if within
specified periodic replacement mileage.
Maintenance and schedules9-21

10 Technical and consumer information
Capacities and recommended fluids/lubricants ..... 10-2Fuel information ....................................................... 10-4
Engine oil and oil filter recommendation ........... 10-6
Air conditioning system refrigerant and
oil recommendations ................................................ 10-7
Specifications .................................................................. 10-8
Engine ........................................................................\
.. 10-8
Wheels and tires ........................................................ 10-9
Dimensions ............................................................... 10-10
When traveling or registering in
another country ............................................................. 10-11
Vehicle identification ................................................... 10-11 Vehicle Identification Number (VIN) plate ....... 10-11
Vehicle identification number
(chassis number) ...................................................... 10-11
Engine serial number ............................................. 10-12
F.M.V.S.S./C.M.V.S.S. certification label ........ 10-12
Emission control information label ................... 10-12
Tire and loading information label .................... 10-13
Air conditioner specification label ..................... 10-13
Installing front license plate ..................................... 10-15
Vehicle loading information ...................................... 10-15 Terms ........................................................................\
. 10-15 Vehicle load capacity ........................................... 10-17
Securing the load ................................................. 10-18
Loading tips ........................................................... 10-18
Measurement of weights ................................... 10-19
Towing a trailer ........................................................... 10-19 Maximum load limits ........................................... 10-19
Maximum Gross Vehicle Weight (GVW)/
maximum Gross Axle Weight (GAW) ............. 10-21
Towing load/specification ................................. 10-22
Towing safety ....................................................... 10-23
Flat towing ............................................................. 10-31
Uniform tire quality grading .................................... 10-31 Treadwear .............................................................. 10-31
Traction AA, A, B and C ..................................... 10-32
Temperature A, B and C .................................... 10-32
Emission control system warranty ......................... 10-32
Reporting safety defects .......................................... 10-33
Readiness for Inspection/Maintenance
(I/M) test ....................................................................... 10-34
Event Data Recorders (EDR) ................................... 10-35
Owner’s Manual/Service Manual
order information ........................................................ 10-35

10-2Technical and consumer information
The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure
instructed in the “8. Do-it-yourself” section to determine the proper refill capacity.
Fluid typeCapacity (approximate)
Recommended Fluids/Lubricants
Metric
Measure US
Measure Imperial
Measure
Fuel 98.4 L26 gal21-5/8 gal

See “Fuel information” (P.10-4).
Engine oil*1 With oil filter change 6.5 L6-7/8 qt 5-3/4 qt

Genuine “NISSAN Motor Oil 0W-20 SP” (or equivalent) is recom-
mended.


If the above motor oil (or engine oil) is not available, a synthetic 0W-
20 GF-6 SP motor oil (or engine oil) may be used. Damage caused by
the use of motor oil (or engine oil) other than as recommended is not
covered under INFINITI’s New Vehicle Limited Warranty. For
additional information, see “Engine oil and oil filter recommendation”
(P.10-6).
Drain and refill
*1: For additional information,
see “Changing engine oil and
filter” (P.8-6).
Without oil filter change 6.2 L6-1/2 qt 5-1/2 qt
Engine coolant
With reservoir 15.1 L
16 qt13-1/4 qt


Pre-diluted Genuine NISSAN Long Life Antifreeze/Coolant (blue) or
equivalent
Automatic transmission fluid (ATF) —— —

Genuine NISSAN Matic S ATF or equivalent


INFINITI recommends using Genuine NISSAN Matic S ATF (or
equivalent) ONLY in INFINITI automatic transmissions. Do not mix
with other fluids. Using fluids that are not equivalent to Genuine
NISSAN Matic S ATF may damage the automatic transmission.
Damage caused by the use of fluids other than as recommended is not
covered under the INFINITI’s New Vehicle Limited Warranty.
Transfer fluid —— —

Genuine NISSAN Transfer Fluid for ATX90A transfer or equivalent


Using transfer fluid other than Genuine NISSAN Transfer Fluid (or
equivalent) may damage the transfer, which is not covered by the
INFINITI New Vehicle Limited Warranty.
Front differential gear oil —— —

Genuine NISSAN Differential Oil Hypoid Super GL-5 80W-90 or
equivalent conventional (non-synthetic) oil
Rear differential gear oil —— —

Genuine NISSAN Differential Oil Hypoid Super-S GL-5 synthetic
75W-90 or equivalent
Power steering fluid (PSF) Refill to the proper oil level according to the instructions
in the “8. Do-it-yourself” section.


Genuine NISSAN PSF or equivalent


DEXRON
TMVI type ATF may also be used.
Brake fluid

Genuine NISSAN Super Heavy Duty Brake Fluid*2 or equivalent DOT
3
*2: Available in mainland U.S.A. through an INFINITI retailer.
Suspension fluid —— —

Genuine NISSAN Hydraulic Suspension Fluid or equivalent


Using Hydraulic Suspension fluid other than Genuine NISSAN
Hydraulic Suspension Fluid (or equivalent) will damage the Hydraulic
Suspension, which is not covered by the INFINITI New Vehicle Limited
Warranty. See an INFINITI retailer for recommended hydraulic
suspension fluid.
Multi-purpose grease —— —

NLGI No. 2 (Lithium soap base)
CAPACITIES AND RECOMMENDED
FLUIDS/LUBRICANTS

10-4Technical and consumer information
FUEL INFORMATION
VK56VD engine
INFINITI recommends the use of unleaded
premium gasoline with an octane rating of at
least 91 AKI (Anti-Knock Index) number
(Research octane number 96).
If unleaded premium gasoline is not avail-
able, you may use unleaded regular gasoline
with an octane rating of at least 87 AKI
number (Research octane number 91), but
you may notice a decrease in performance.
CAUTION
.Using a fuel other than that specified
could adversely affect the emission
control system, and may also affect
warranty coverage.
. Under no circumstances should a
leaded gasoline be used, because this
will damage the three-way catalyst.
. Do not use E-15 or E-85 fuel in your
vehicle. Your vehicle is not designed
to run on E-15 or E-85 fuel. Using E-
15 or E-85 fuel in a vehicle not
specifically designed for E-15 or E-
85 fuel can adversely affect the
emission control devices and systems
of the vehicle. Damage caused by such fuel is not covered by the
INFINITI new vehicle limited war-
ranty.
. Do not use fuel that contains the
octane booster methylcyclopentadie-
nyl manganese tricarbonyl (MMT).
Using fuel containing MMT may
adversely affect vehicle performance
and vehicle emissions. Not all fuel
dispensers are labeled to indicate
MMT content, so you may have to
consult your gasoline retailer for
more details. Note that Federal and
California laws prohibit the use of
MMT in reformulated gasoline.
. U.S. government regulations require
ethanol dispensing pumps to be iden-
tified by a small, square, orange and
black label with the common abbre-
viation or the appropriate percen-
tage for that region.
Gasoline specifications
INFINITI recommends using gasoline that
meets the World-Wide Fuel Charter
(WWFC) specifications where it is available.
Many of the automobile manufacturers
developed this specification to improve
emission system and vehicle performance.
Ask your service station manager if the
gasoline meets the World-Wide Fuel Char- ter (WWFC) specifications.
Reformulated gasoline
Some fuel suppliers are now producing
reformulated gasolines. These gasolines are
specially designed to reduce vehicle emis-
sions. INFINITI supports efforts towards
cleaner air and suggests that you use
reformulated gasoline when available.
Gasoline containing oxygenates
Some fuel suppliers sell gasoline containing
oxygenates such as ethanol, MTBE and
methanol with or without advertising their
presence. INFINITI does not recommend the
use of fuels of which the oxygenate content
and the fuel compatibility for your INFINITI
cannot be readily determined. If in doubt, ask
your service station manager.
If you use oxygenate-blend gasoline, please
take the following precautions as the usage
of such fuels may cause vehicle performance
problems and/or fuel system damage.
.
The fuel should be unleaded and have an
octane rating no lower than that re-
commended for unleaded gasoline.
. If an oxygenate-blend, excepting a
methanol blend, is used, it should con-
tain no more than 10% oxygenate.
(MTBE may, however, be added up to
15%.)

.E-15 fuel contains more than 10%
oxygenate. E-15 fuel will adversely
affect the emission control devices and
systems of the vehicle and should not be
used. Damage caused by such fuel is not
covered by the INFINITI new vehicle
limited warranty.
. If a methanol blend is used, it should
contain no more than 5% methanol
(methyl alcohol, wood alcohol). It should
also contain a suitable amount of ap-
propriate cosolvents and corrosion in-
hibitors. If not properly formulated with
appropriate cosolvents and corrosion
inhibitors, such methanol blends may
cause fuel system damage and/or vehi-
cle performance problems. At this time,
sufficient data is not available to ensure
that all methanol blends are suitable for
use in INFINITI vehicles.
If any undesirable driveability problems such
as engine stalling or hard hot starting are
experienced after using oxygenate-blend
fuels, immediately change to a non-oxyge-
nate fuel or a fuel with a low blend of MTBE.
Take care not to spill gasoline during
refueling. Gasoline containing oxygenates
can cause paint damage.E-15 fuel
E-15 fuel is a mixture of approximately 15%
fuel ethanol and 85% unleaded gasoline. E-
15 can only be used in vehicles designed to
run on E-15 fuel. Do not use E-15 in your
vehicle. U.S. government regulations require
fuel ethanol dispensing pumps to be identi-
fied with small, square, orange and black
label with the common abbreviation or the
appropriate percentage for that region.
E-85 fuel
E-85 fuel is a mixture of approximately 85%
fuel ethanol and 15% unleaded gasoline. E-
85 can only be used in a Flexible Fuel Vehicle
(FFV). Do not use E-85 fuel in your vehicle.
U.S. government regulations require fuel
ethanol dispensing pumps to be identified
by a small, square, orange and black label
with the common abbreviation or the appro-
priate percentage for that region.
Fuel containing MMT
MMT, or methylcyclopentadienyl manga-
nese tricarbonyl, is an octane boosting
additive. INFINITI does not recommend the
use of fuel containing MMT. Such fuel may
adversely affect vehicle performance, in-
cluding the emissions control system. Note
that while some fuel pumps label MMT
content, not all do, so you may have to consult your gasoline retailer for more de-
tails.
Aftermarket fuel additives
INFINITI does not recommend the use of any
aftermarket fuel additives (Example: fuel
injector cleaner, octane booster, intake valve
deposit removers, etc.) which are sold com-
mercially. Many of these additives intended
for gum, varnish or deposit removal may
contain active solvent or similar ingredients
that can be harmful to the fuel system and
engine.
Octane rating tips
Using unleaded gasoline with an octane
rating lower than recommended above can
cause persistent, heavy spark knock. (Spark
knock is a metallic rapping noise.) If severe,
this can lead to engine damage. If you
detect a persistent heavy spark knock even
when using gasoline of the stated octane
rating, or if you hear steady spark knock
while holding a steady speed on level roads,
it is recommended you have an INFINITI
retailer correct the condition. Failure to
correct the condition is misuse of the
vehicle, for which INFINITI is not respon-
sible.
Incorrect ignition timing will result in knock-
ing, after-run or overheating. This in turn
may cause excessive fuel consumption or
Technical and consumer information10-5