Oil chart ISUZU AXIOM 2002 Service Manual PDF

9J1±9
RESTRAINT CONTROL SYSTEM
Chart B ªAIR BAGº Warning Lamp Comes ªONº Steady
StepActionYe sNo
11. When measurements are requested in this chart use J±39200
DVM with correct terminal adapter from J±35616±A.
2. Ignition switch ªOFF.º
3. Connect scan tool to data link connector, Follow directions as
given in the scan tool instruction manual.
4. Ignition switch ªON.º
5. Request SRS diagnostic trouble code display.
Does scan tool indicate ªNo Data Receivedº?
Go to Step 2 Go to Step 3
21. Ignition switch ªOFF.º
2. Inspect SDM harness connector connection to SDM.
Is it securely connected to the SDM?
Ignition switch
ªOFF.º
Replace SDM.
Go to
Step 5
Connect SDM
securely to
de±activate
shorting clip in
SDM harness
connector.
Go to
Step 5
3Using scan tool, request SRS data list.
Is ªignitionº more than 9 volts?
Go to Step 4
Ignition switch
ªOFF.º
Replace SDM.
Go to
Step 5
41. Ignition switch ªOFF.º
2. Disconnect SRS coil and passenger air bag assemblies.
Yellow 2±pin connectors located at base of steering column
and behind the glove box assembly.
3. Disconnect SDM.
4. Measure resistance from SDM harness connector terminal ª6º
to ground.
Does J±39200 display ª0Lº (infinite)?
Go to Chart A.
Replace SRS
harness.
Go to
Step 5
5Reconnect all SRS components, ensure all components are
properly mounted.
Was this step finished?Repeat the ªSRS
Diagnostic
System Check.º
Go to Step 5

9J1±11
RESTRAINT CONTROL SYSTEM
Chart C ªAIR BAGº Warning Lamp Does Not Comes ªONº Steady
StepActionYe sNo
11. When measurements are requested in this chart use J±39200
DVM with correct terminal adapter from J±35616±A.
2. Ignition switch ªOFF.º
3. Remove and inspect ªMA01º meter fuse to the ªAIR BAGº
warning lamp.
Is fuse good?
Go to Step 2 Go to Step 7
21. Ignition switch ªOFF.º
2. Disconnect SRS coil and passenger air bag assemblies.
Yellow 2±pin connectors located at base of steering column
and behind the glove box assembly.
3. Disconnect SDM.
4. Ignition switch ªON.º
5. Measure voltage on SDM harness connector from terminal ª7º
to terminal ª6º (ground).
Is system voltage present on terminal ª7º?
Go to Step 4 Go to Step 3
31. Ignition switch ªOFF.º
2. Remove instrument meter cluster.
3. Check for proper connection to instrument cluster at
IB04±GRN terminal.
4. If OK, then remove and inspect ªAIR BAGº bulb.
Is bulb good?
Go to Step 5
Replace bulb.
Go to
Step 6
41. Ignition switch ªOFF.º
2. Disconnect instrument meter cluster harness connector.
3. Ignition switch ªON.º
4. Measure voltage on SDM harness connector from terminal ª7º
to terminal ª6º (ground).
Is voltage 1 volt or less?
Go to Chart A.
Replace SRS
harness.
Go to
Step 6
51. Install bulb.
2. Measure resistance from instrument meter cluster harness
connector IB04±GRN terminal to SDM harness connector
terminal ª7º.
Is resistance 5.0 ohms or less?
Service
instrument meter
cluster.
Go to
Step 6
Replace SRS
harness.
Go to
Step 6
6Reconnect all SRS components, ensure all components are
properly mounted.
Was this step finished?Repeat the ªSRS
Diagnostic
System Check.º
Go to Step 6
7Were you sent here from chart C?Go to Step 8 Go to Step 1
81. Replace ªMA01º meter fuse.
2. Ignition switch ªONº wait 10 seconds then ignition switch
ªOFF.º
3. Remove and inspect ªMA01º meter fuse.
Is fuse good?
Install ªMA01º
meter fuse.
Go to
Step 10 Go to Step 9

RESTRAINT CONTROL SYSTEM 9J1±12
Chart C ªAIR BAGº Warning Lamp Does Not Comes ªONº Steady (Cont'd)
StepNo Ye s Action
91. Disconnect SRS coil and passenger air bag assemblies.
Yellow 2±pin connectors located at base of steering column
and behind the glove box assembly.
2. Disconnect SDM.
3. Replace ªMA01º meter fuse.
4. Ignition switch ªONº wait to 10 seconds.
5. Ignition switch ªOFFº.
6. Remove and inspection ªMA01º meter fuse.
Is fuse good?
Install ªMA01º
meter fuse.
Go to
Chart A .
Replace SRS
harness.
ReplaceªMA01º
meter fuse.
Go to
Step 10
10Reconnect all SRS components, ensure all components are
properly mounted.
Was this step finished?Repeat the ªSRS
Diagnostic
System Check.º
Go to Step 10

9J1±15
RESTRAINT CONTROL SYSTEM
DTC 15 Passenger Deployment Loop Resistance High
StepActionYe sNo
1Was the ªSRS Diagnostic System Checkº performed?
Go to Step 2
Go to the ªSRS
Diagnostic
System Check.º
21. When measurements are requested in this chart use J±39200
DVM with correct terminal adapter from J±35616±A.
2. Use scan tool data list function, read and record the passenger
deployment loop resistance.
Is passenger resist more than 2.9 ohms?
Go to Step 3 Go to Chart A .
31. Ignition switch ªOFF.º
2. Make sure the passenger air bag assembly yellow 2±pin
connector located behind the glove box assembly is seated
properly.
Is the yellow 2±pin connector connected properly?
Go to Step 4
Seat passenger
air bag assembly
yellow 2±pin
connector
properly.
Go to
Step 7
41. Disconnect and inspect the passenger air bag assembly
yellow 2±pin connector located behind the glove box
assembly.
2. If OK, reconnect the passenger air bag assembly 2±pin
connector.
3. Ignition switch ªON.º
Is DTC 15 current?
Go to Step 5
Ignition switch
ªOFF.º
Go to
Step 7
51. Ignition switch ªOFF.º
2. Disconnect SRS coil and passenger air bag 2±pin connectors
located at the base of the steering column and behind the
glove box assembly.
3. Connect J±41433 SRS driver / passenger load tool and
appropriate adapters to SRS coil and passenger air bag
assembly harness connectors.
4. Ignition switch ªON.º
Is DTC 15 current?
Go to Step 6
Ignition switch
ªOFF.º
Replace the
passenger air
bag assembly.
Go to
Step 7
61. Ignition switch ªOFF.º
2. There has been an increase in the total circuit resistance of the
passenger inflator deployment loop.
3. Use the high resolution ohmmeter mode of the DVM while
checking CKTs IB07±YEL/GRN and IB08±YEL/RED, and
SDM connector terminal ª15º and ª16º to locate the root cause.
Was a fault found?
Replace SRS
harness.
Go to
Step 7 Go to Chart A .
71. Reconnect all components ensure all component are properly
mounted.
2. Clear diagnostic trouble codes.
Was this step finished?
Repeat the ªSRS
Diagnostic
System Check.º
Go to Step 7

RESTRAINT CONTROL SYSTEM 9J1±18
DTC 16 Passenger Deployment Loop Resistance Low
StepActionYe sNo
1Was the ªSRS Diagnostic System Checkº performed?
Go to Step 2
Go to the ªSRS
Diagnostic
System Check.º
21. When measurements are requested in this chart use J±39200
DVM with correct terminal adapter from J±35616±A.
2. Using scan tool data list function, read and record the
passenger deployment loop resistance.
Is passenger resist. less than 1.4 ohms?
Go to Step 3 Go to Chart A .
31. Ignition switch ªOFF.º
2. Make sure the passenger air bag assembly yellow 2±pin
connector located behind the glove box assembly is seated
properly.
Is the yellow 2±pin connector connected properly?
Go to Step 4
Seat passenger
air bag assembly
yellow 2±pin
connector
properly.
Go to
Step 7
41. Disconnect and inspect the passenger air bag assembly
yellow 2±pin connector located behind the glove box
assembly.
2. If OK, reconnect the passenger air bag assembly 2±pin
connector.
3. Ignition switch ªON.º
Us DTC 16 current?
Go to Step 5
Ignition switch
ªOFF.ºGo to
Step
7

51. Ignition switch ªOFF.º
2. Disconnect SRS coil and passenger air bag 2±pin connectors
located at the base of the steering column and behind the
glove box assembly.
3. Connect J±41433 SRS driver / passenger load tool and
appropriate adapters to SRS coil and passenger air bag
assembly harness connectors.
4. Ignition switch ªON.º
Is DTC 16 current?
Go to Step 6 .
Ignition switch
ªOFF.º
Replace the
passenger air
bag assembly.
Go to
Step 7
61. Ignition switch ªOFF.º
2. There has been a decrease in the total circuit resistance of the
passenger inflator deployment loop.
3. Use the high resolution ohmmeter mode of the DVM while
checking CKTs IB07±YEL/GRN and IB08±YEL/RED, and
SDM connector terminal ª15º and ª16º to locate the root cause.
Was a fault found?
Replace SRS
harness.
Go to
Step 7 Go to Chart A .
71. Reconnect all components, ensure all component are properly
mounted.
2. Clear diagnostic trouble codes.
Was this step finished?
Repeat the ªSRS
Diagnostic
System Check.º
Go to Step 7

RESTRAINT CONTROL SYSTEM 9J1±20
DTC Chart Test Description:
Number(s) below refer to step number(s) on the
diagnostic chart:
2. This test determines whether the malfunction is in
the SDM.
3. This test verifies proper connection of the yellow
2±pin connector.
4. This test cheeks for proper contact and/or corrosion
of the shorting clip in the yellow 2±pin connector
terminals.5. The test checks for a malfunctioning passenger air
bag assembly.
6. This test determines whether there is an open in the
wiring.
Diagnostic Aids:
An intermittent condition is likely to be caused by a poor
connection at the passenger air bag assembly harness
connector terminals ª1º and ª2,º SDM terminals ª15º and
ª16,º or an open in CKT IB07±YEL/GRN and
IB08±YEL/RED.
DTC 17 Passenger Deployment Loop Open
StepActionYe sNo
1Was the ªSRS Diagnostic System Checkº performed?
Go to Step 2
Go to the ªSRS
Diagnostic
System Check.º
21. When measurements are requested in this chart use J±39200
DVM with correct terminal adapter from J±35616±A.
2. Using scan tool data list function, read and record the
passenger differential voltage.
Is passenger differential voltage. more than 4.0 volts?
Go to Step 3 Go to Chart A .
31. Ignition switch ªOFF.º
2. Make sure the passenger air bag assembly yellow 2±pin
connector located behind the glove box assembly is seated
properly.
Is the yellow 2±pin connector connected properly?
Go to Step 4
Seat passenger
air bag assembly
yellow 2±pin
connector
properly.
Go to
Step 7
41. Disconnect and inspect the passenger air bag assembly
yellow 2±pin connector located behind the glove box
assembly.
2. If OK, reconnected the passenger air bag assembly yellow
2±pin connector.
3. Ignition switch ªON.º
Is DTC 17 current?
Go to Step 5
Ignition switch
ªOFF.º
Go to
Step 7
51. Ignition switch ªOFF.º
2. Disconnect SRS coil and passenger air bag assembly yellow
2±pin connectors located at the base of the steering column
and behind the glove box assembly.
3. Connect J±41433 SRS driver / passenger load tool and
appropriate adapters to SRS coil and passenger air bag
assembly harness connectors.
4. Ignition switch ªON.º
Is DTC 17 current?
Go to Step 6
Ignition switch
ªOFF.º
Replace the
passenger air
bag assembly.
Go to
Step 7
61. Ignition switch ªOFF.º
2. There has been an open circuit in the passenger inflator
deployment loop.
3. Use the high resolution ohmmeter mode of the DVM while
checking CKTs IB07±YEL/GRN and IB08±YEL/RED, and
SDM connector terminal ª15º and ª16º to locate the root cause.
Was a fault found?
Replace SRS
harness.
Go to
Step 7 Go to Chart A .
71. Reconnect all components ensure all component are properly
mounted.
2. Clear diagnostic trouble codes.
Was this step finished?
Repeat the ªSRS
Diagnostic
System Check.º
Go to Step 7

RESTRAINT CONTROL SYSTEM 9J1±26
DTC Chart Test Description:
Number(s) below refer to step number(s) on the
diagnostic chart:
2. This test determines whether the malfunction is in
the SDM.
3. This test verifies proper connection of the yellow
2±pin connector at the base of the steering column.
4. This test checks for proper contact and/or corrosion
of the 2±pin connector terminals at the base of
steering column.
5. This test isolate the malfunction to one side of the
SRS coil assembly yellow 2±pin connector located
at the base of the steering column.
6. This test determines whether the malfunction is due
to high resistance in the wiring.
7. This test determines whether the malfunction is in
the SRS coil assembly or the driver air bag
assembly.
Diagnostic Aids:
An intermittent condition is likely to be caused by a poor
connection at terminals ª1º and ª2º of the SRS coil 2±pin
connector at the base of the steering column, terminal ª1º
and ª2º of the driver air bag assembly 2±pin connector at
the top of the steering column, SDM terminals ª3º and ª4º
or a poor wire to terminal connection in CKT IB05±YEL or
IB06±YEL/BLK. The test for this diagnostic trouble code
is only run while the ªAIR BAGº warning lamp is
performing the bulb check, unless DTC 17 or DTC 26 is
detected. When a scan tool ªClear Codesº command is
issued and the malfunction is still present, the DTC will not
reappear until the next ignition cycle.

9J1±27
RESTRAINT CONTROL SYSTEM
DTC 21 Driver Deployment Loop Resistance High
StepActionYe sNo
1Was the ªSRS Diagnostic System Checkº performed?
Go to Step 2
Go to the ªSRS
Diagnostic
System Check.º
21. When measurements are requested in this chart use J±39200
DVM with correct terminal adapter from J±35616±A.
2. Use scan tool data list function, read and record the driver
deployment loop resistance.
Is driver deployment loop resistance more than 4.4 ohms?
Go to Step 3 Go to Chart A .
31. Ignition switch ªOFF.º
2. Disconnect driver air bag assembly yellow 2±pin connector
located at base of steering column is seated properly.
Is the 2±pin connector connected properly?
Go to Step 4
Seat SRS coil
assembly 2±pin
connector
properly.Go to
Step 8
41. Disconnect and inspect the SRS coil assembly yellow 2±pin
connector located base of steering column.
2. If OK, reconnect the SRS coil assembly yellow 2±pin
connector.
3. Ignition switch ªON.º
Is DTC 21 current?
Go to Step 5
Ignition switch
ªOFF.º
Go to
Step 8
51. Ignition switch ªOFF.º
2. Disconnect SRS coil and passenger air bag assembly yellow
2±pin connectors located at the base of steering column and
behind the glove box assembly.
3. Connect SRS driver / passenger load tool J±41433 and
appropriate adapter to SRS coil and passenger air bag
assembly harness connectors.
4. Ignition switch ªON.º
Is DTC 21 current?
Go to Step 6 Go to Step 7
61. Ignition switch ªOFF.º
2. There has been a increase in the total circuit resistance of the
driver deployment loop.
3. Use the high resolution ohmmeter mode of the DVM while
checking CKTs IB05±YEL/IB06±GRN and YEL/BLK, and
SDM connector terminal ª3º and ª4º to locate the root cause.
Was a fault found?
Replace SRS
harness.
Go to
Step 8 Go to Chart A .
71. Ignition switch ªOFF.º
Disconnect SRS driver / passenger load tool from SRS coil
assembly harness connector.
Connect SRS driver / passenger load tool J±41433 on the top
of steering column.
Reconnect SRS coil assembly harness connector as the base
of steering column.
Ignition switch ªON.º
Is DTC 21 current?
Ignition switch
ªOFF.º
Replace SRS
COIL
ASSEMBLY.
Refer to in this
section 9J±24.
Go to
Step 8
Ignition switch
ªOFF.º
Replace driver air
bag assembly.
Go to
Step 8
8Reconnect all components, ensure all component are properly
mounted.
Clear diagnostic trouble codes.
Was this step finished?
Repeat the ªSRS
Diagnostic
System Check.º
Go to Step 8 .

9J1±29
RESTRAINT CONTROL SYSTEM
DTC Chart Test Description:
Number(s) below refer to step number(s) on the
diagnostic chart:
2. This test determines whether the malfunction is in
the SDM.
3. This test verifies proper connection of the yellow
2±pin connector at the base of the steering column.
4. This test checks for proper operation of the shorting
clip in the yellow 2±pin connector.
5. This test isolate the malfunction to one side of the
SRS coil assembly yellow 2±pin connector located
at the base of steering column.
6. This test determines whether the malfunction is due
to shorting in the wiring.
7. This test determines whether the malfunction is in
the SRS coil assembly or the driver air bag
assembly.
Diagnostic Aids:
An intermittent condition is likely to be caused by a short
between CKT IB05±YEL or IB06±YEL/BLK or a
malfunctioning shorting clip on the driver air bag
assembly or SRS coil assembly which would require
replacement of the component. The test for this
diagnostic trouble code is only run while the ªAIR BAGº
warning lamp is performing the bulb check, unless DTC
17 or DTC 26 is detected. When a scan tool ªClear
Codesº command is issued and the malfunction is still
present, the DTC will not reappear until the next ignition
cycle.

RESTRAINT CONTROL SYSTEM 9J1±30
DTC 22 Driver Deployment Loop Resistance Low
StepActionYe sNo
1Was the ªSRS Diagnostic System Checkº performed?
Go to Step 2
Go to the ªSRS
Diagnostic
System Check.º
21. When measurements are requested in this chart use J±39200
DVM with correct terminal adapter from J±35616±A.
2. Use scan tool data list function, read and record the driver
deployment loop resistance.
Is driver resist. less than 1.9 ohms?
Go to Step 3 Go to Chart A .
31. Ignition switch ªOFF.º
2. Make sure the SRS coil assembly yellow 2±pin connector
located at the base of steering column is seated properly.
Is the 2±pin connector connected properly?
Go to Step 4
Seat driver air
bag assembly
2±pin connector
properly.
Go to
Step 8
41. Disconnect and inspect the SRS coil assembly yellow 2±pin
connector located base of steering column.
2. If OK, reconnect the driver air bag assembly yellow 2±pin
connector.
3. Ignition switch ªON.º
Is DTC 22 current?
Go to Step 5
Ignition switch
ªOFF.º
Go to
Step 8
51. Ignition switch ªOFF.º
2. Disconnect SRS coil and passenger air bag 2±pin connectors
located at the base of steering column and behind the glove
box assembly.
3. Connect SRS driver / passenger load tool J±41433 and
appropriate adapter to SRS coil and passenger air bag
assembly harness connectors.
4. Ignition switch ªON.º
Is DTC 22 current?
Go to Step 6 Go to Step 7
61. Ignition switch ªOFF.º
2. There has been a decrease in the total circuit resistance of the
driver deployment loop.
3. Use the high resolution ohmmeter mode of the DVM while
checking CKTs IB05±YEL and IB06±YEL/BLK, and SDM
connector terminal ª3º and ª4º to locate the root cause.
Was a fault found?
Replace SRS
harness.
Go to
Step 8 Go to Chart A .
71. Ignition switch ªOFF.º
2. Disconnect SRS driver / passenger load tool from SRS coil
assembly harness connector.
3. Connect SRS driver / passenger load tool J±41433 to the top
of steering column.
4. Reconnect SRS coil assembly harness connector as the base
of steering column.
5. Ignition switch ªON.º
Is DTC 22 current?
Ignition switch
ªOFF.º
Replace SRS coil
assembly.
Refer to in this
section 9J±24.
Go to
Step 8
Ignition switch
ªOFF.º
Replace driver air
bag assembly.
Go to
Step 8
81. Reconnect all components, ensure all component are properly
mounted.
2. Clear diagnostic trouble codes.
Was this step finished?
Repeat the ªSRS
Diagnostic
System Check.º
Go to Step 8