oil ISUZU TF SERIES 2004 Workshop Manual

8A-420 ELECTRICAL-BODY AND CHASSIS


No. Connector face No. Connector face
B-55
White
J/B I3 B-65
SilverWeld splice 2 (Ground)
B-56
White
J/B I4 B-66
White44 switch
B-57
White
HVAC control unit B-67
(6VE1)
BlackCruise main
B-58
Black
Check connector B-68
(6VE1)
(4JH1-TC)
Immobilizer
B-59
White
Combination switch-A B-69
Door lock switch
B-60
White
Combination switch-B B-70
(6VE1)
(4JH1-TC)
Immobilizer Coil
B-61
Black
Flasher relay B-71
YellowHorn
B-62
White
Ignition switch (IGSUB : G1) B-72
YellowSRS
B-63
White
Ignition switch (IGSUB : G2) B-73
BlackWeld Splice 3
B-64
Silver
Weld splice 1 (Illumination) B-74
WhiteCellular phone

ELECTRICAL-BODY AND CHASSIS 8A-421


No. Connector face No. Connector face
B-75
Black
Rear fog C/U


B-76
White
Front & rear fog light switch


B-77
(4JA1-L)
White Immobilizer C/U


B-78
White
Immobilizer antenna coil


B-79
White
Short connector (cooler only)


B-80
Black
Hazard relay (RH)


B-81
Black
Hazard relay (LH)

8A-428 ELECTRICAL-BODY AND CHASSIS


No. Connector face No. Connector face
E-1
(4JH1-TC)
White Oil pressure switch E-10
SilverEngine ground
E-2
(C24SE)
(6VE1)


Magnetic clutch E-11
(6VE1)

Neutral switch
E-3
(4JH1-TC)
Black
Magnetic clutch AC COMP E-11
(4JH1-TC)
Natural
green
Neutral switch
E-4
~
E-5 NOT USED E-12
(6VE1)

Neutral switch
E-6
(C24SE)
(6VE1)


(6VE1) Fuel injector (C24SE) E-12
(4JH1-TC)
Natural
green
Neutral switch
E-6
(4JH1-TC)

Injector pump E-13
~
E-17 NOT USED
E-7
(C24SE)
(6VE1)


(6VE1) Fuel injector (C24SE) E-18
(C24SE)

Ignition coil
E-8
(C24SE)
(6VE1)


(6VE1) Fuel injector (C24SE) E-19
(4JH1-TC)
Blue Thermo meter unit
E-9
(C24SE)
(6VE1)


(6VE1) Fuel injector (C24SE) E-20
~
E-21 NOT USED
E-9
(4JH1-TC)
Gray T.D.C sensor E-22
(4JH1-TC)
BrownTPS 1 main

ELECTRICAL-BODY AND CHASSIS 8A-429


No. Connector face No. Connector face
E-23
(4JH1-TC)
Gray TPS 2 main E-44
Gray Vehicle speed sensor
E-24
~
E-29 NOT USED E-45
(4JH1-TC)
Gray 2WD-4WD switch
E-30
(4JH1-TC)
Gray A/T speed sensor E-46
(4JH1-TC)
BrownH-L neutral switch
E-31
(4JH1-TC)
Gray Turbine sensor E-47
~
E-48 NOT USED
E-32
~
E-34 NOT USED E-49
(4JH1-TC)
Glow plug
E-35
(4JH1-TC)
(C24SE)
Black Motor actuator E-50

NOT USED
E-36
~
E-40 NOT USED E-51
(6VE1)
Fuel injector
E-41
(4JH1-TC)
Black Coolant temp sensor E-51
(4JH1-TC)
BlackInhibiter switch
E-42
Natural
green
Backup lamp switch E-52
(6VE1)
Fuel injector
E-43
Natural
green
Backup lamp switch E-53
(6VE1)
Ignition coil

8A-430 ELECTRICAL-BODY AND CHASSIS


No. Connector face No. Connector face
E-54
(6VE1)
Ignition coil E-62
(6VE1)
Cam position sensor
E-54
(4JH1-TC)
Black A/T term ASM E-64
(C24SE)
(6VE1)
Oil pressure switch (P/STRG)
E-55
(6VE1)
Ignition coil E-65
(C24SE)
(6VE1)
Thermo unit
E-56
(6VE1)
Ignition coil E-66
(C24SE)
(6VE1)
Duty solenoid
E-57
(6VE1)
Ignition coil E-67
NOT USED
E-58
(6VE1)
Ignition coil E-68
(C24SE)
Throttle position sensor
E-59
(C24SE)
(6VE1)
(6VE1) Crank position sensor (C24SE) E-68
(6VE1)
Throttle position sensor
E-60
(C24SE)
ECM E-69
(6VE1)
Temperature sensor
E-60
(6VE1)
ECM-A E-70
(C24SE)
IACV
E-61
(6VE1)
ECM-B E-70
(6VE1)
IACV

ELECTRICAL-BODY AND CHASSIS 8A-431


No. Connector face No. Connector face
E-71

NOT USED E-80
(6VE1)
Cylinder revolution
E-72
(C24SE)
(6VE1)
Engine earth-A E-81
(6VE1)
Speed sensor
E-73
(6VE1)
Engine earth-A E-82
(6VE1)
Transmission wire
E-74
(C24SE)
(6VE1)
Engine earth-B E-83
(6VE1)
Oil temperature sensor
E-75
(C24SE)
(6VE1)
Oil pressure switch E-84
(C24SE)
Knock sensor
E-76
(6VE1)
EGR valve E-85
(C24SE)
MAP sensor
E-77
(C24SE)
O2 sensor E-86
(4JA1-L)
SilverThermo switch; QOS
E-77
(6VE1)
O2 sensor RH-Front E-87
(4JA1-L)
WhiteSolenoid CSD
E-78
(6VE1)
O2 sensor LH-Front E-88
(4JA1-L)
SilverThermo switch; EGR
E-79
(6VE1)
Neutral start switch E-89
(4JA1-L)
White

Immobilizer engine control unit

TROUBLESHOOTING 6 – 1


SECTION 6
TROUBLESHOOTING


TABLE OF CONTENTS
PAGE PAGE
BASIC INSPECTION PROCEDURE ... 6– 2

1. HARD STARTING ........................... 6– 3

1-1.Starter Motor Inoperative ......... 6– 3

1-2. Starter Motor Operates But
Engine Does Not Turn Over .......... 6– 3

1-3. Engine Turns Over But Does
Not Start Engine ............................. 6– 4

2. UNSTABLE IDLING ........................ 6– 5

3. INSUFFICIENT POWER ................. 6– 6

4. EXCESSIVE FUEL
CONSUMPTION ................................. 6– 7

5. EXCESSIVE OIL CONSUMPTION.. 6– 8

6. OVERHEATING............................... 6– 9

7. WHITE EXHAUST SMOKE ............. 6– 9

8. DARK EXHAUST SMOKE .............. 6– 10

9. OIL PRESSURE DOES NOT RISE . 6– 11

10. ABNORMAL ENGINE NOISE ....... 6– 12

10-1. Engine Knocking.................... 6– 12

10-2. Gas Leakage Noise ................ 6– 12

10-3. Continuous Noise .................. 6– 13

10-4. Slapping Noise ....................... 6– 13

10-5. Excessive Turbocharger
Noise ............................................... 6– 14
11. ROTATING PART WEAR OF
TURBOCHARGER ............................. 6– 14

12. OIL LEAKAGE FROM
TURBOCHRGER ............................... 6– 15

13. INSUFFICIENT ACCELERATION
AND/OR LACK OF POWER DUE
TO TURBOCHARGER ....................... 6– 15

14. BATTERY CHARGING AND
NOISE PROBLEM.............................. 6– 16

14-1. Battery No Charging .............. 6– 16

14-2. Battery Overcharging ............ 6– 16

14-3. Battery Under Charging......... 6– 17

14-4. Battery Unstable Charging
Current ............................................ 6– 17

14-5. Charging System Noise ......... 6– 18

15. STARTER MOTOR PROBLEM..... 6– 19

15-1. Starter Motor Pinion Engages
to Ring Gear But Engine Does
Not Turn Over ................................. 6– 19

15-2. Incorrect Pinion And Ring
Gear Engagement .......................... 6– 19

15-3. Starter Motor Continues To
Run After The Starter Switch Is
Turned Off ....................................... 6– 20

15-4. Excessive Commutator
Sparking .......................................... 6– 20

6 – 2 TROUBLESHOOTING
Basic Inspection Procedure
Follow the under inspection procedure, when the problem vehicle comes workshop.
Step Inspection point Inspection result YES NO
1 Check the check engine lamp Is the check engine lamp turn
ON ? Go to section
6E “On Board
Diagnostic
(OBD) System
Check" Go to Step 2
2 The battery fluid level and the
gravity Was the problem found? Re-charge the
battery or
replace the
battery Go to Step 3
3 The engine coolant capacity Was the problem found? Replenish the
engine coolant Go to Step 4
4 The engine oil level Was the problem found? Replenish the
engine oil Go to Step 5
5 The air cleaner element Was the problem found? Clean or
replace Go to Step 6
6 The piping fixing condition (oil,
vacuum and fuel piping) Was the problem found? Return normal
condition Go to Step 7
7 The drive belt tension and break Was the problem found? Re-adjust the
tension or
replace Go to Step 8
8 Go to section 6E “On Board
Diagnostic (OBD) System
Check” Was the problem found?
Verify repair Go to Step 9
9 Go to mechanical
troubleshooting chart Was the problem found?
Verify repair —

6 – 8 TROUBLESHOOTING
5. Excessive Oil Consumption
Step Action Value(s) Yes No
1 Does the air cleaner element conditon OK? (Clogged
or not) —
Go to Step 2 Clean or
replace the air
cleaner
element
2 Does PCV (Positive Crankcase Ventilation) Valve
has problem? — Repair or
replace the
relation parts. Go to Step 3
3 Was the oil pressure value more than normal value? Less than
588 kPa (6.0
kg/cm
2, 85
psi) Repair or
replace the oil
relief valve Go to Step 4
4 Inspect the front and rear crankshaft oil seal.
Was the oil leakage found? —
Replace the
failure part. Go to Step 5
5 Was the oil leakage found from any gasket? — Replace the
wrong gasket Go to Step 6
6 Inspect the valve stem seal, the valve stem and the
valve guide for worn.
Were any worn found? —
Replace the
worn part. Go to Step 7
7 Was the oil leakage found from the turbocharger oil
seal? — Replace the oil
seal. Go to Step 8
8 Was the oil drain pipe of the turbocharger restricted?— Repair or
replace the oil
drain pipe. Go to Step 9
9 Was the oil drain passage in the turbocharger center
housing restricted? — Clean the
center housing Go to Step 10
10 Does turbine wheel has any impact damage? — Replace the
turbocharger Go to Step 11
11 Are any DTC stored? — Go to indicated
DTC Solved

TROUBLESHOOTING 6 – 9
6. Overheating
Step Action Value(s) Yes No
1 Was the engine coolant level OK? —
Go to Step 2 Replenish the
coolant
2 Was the water leakage or the radiator restriction
found? (Include radiator cap) — Repair or
replace the
leakage part. Go to Step 3
3 Was the fan belt slippage found? — Tension or
replace the fan
belt. Go to Step 4
4 Was the fan clutch working completely? —
Go to Step 5 Replace the
fan clutch
assembly.
5 Was the oil leakage found from fan clutch? — Replace the
fan clutch
assembly Go to Step 6
6 Was the thermostat working normally? —
Go to Step 7 Replace the
thermostat.
7 Was the water pump working OK? —
Go to Step 8 Replace the
water pump
assembly.
8 Was the restriction by the foreign materials in the
cooling system found? For example, clog the water
hose between the cylinder body and radiator etc.. — Clean or
replace the
clog part. Go to Step 9
9 Was the water leakage found from the sealing cap
on the cylinder body? — Replace the
sealing cap or
replace the
cylinder body. Go to Step 10
10 Are any DTC stored? — Go to indicated
DTC. Solved

7. White Exhaust Smoke
Step Action Value(s) Yes No
1 Was the compression pressure OK? 3.0 MPa
(31.0 kg/cm2,
441 psi) at
200 rpm
Go to Step 2 Readjust the
valve clearance
or replace the
cylinder head
gasket or
cylinder liner or
piston or piston
ring or valve
and relation
parts.
2 Was the PCV (Positive Crankcase Ventilation) valve
working completely? —
Go to Step 3 Repair or
replace the
PCV valve.
3 Was the turbocharger working completely? —
Go to Step 4 Replace the
turbocharger.
4 Are any DTC stored? — Go to indicated
DTC Solved