coolant reservoir ISUZU TF SERIES 2004 User Guide

ENGINE COOLING 6B-13

Installation
1. Install radiator assembly, taking care not to damage the
radiator core.
2. Install the radiator assembly.
3. Connect reserve tank hose.
4. Connect radiator inlet hose and outlet hose.
5. Pour engine coolant up to filler neck of radiator, and up to
MAX mark of reserve tank.
Important operation (in case of 100% engine coolan
t
change) procedure for filling with engine coolant.

Remove radiator cap.

Fill with engine coolant (EC) to the radiator filler neck.

Fill with EC to the "MAX" line on the reservoir tank.

Start the engine with the radiator cap removed and bring to
operating temperature by running engine at 2,500 - 3,000
rpm for 30 minutes.

By EC temperature gauge reading make sure that the
thermostat is open.

If air bubbles come up to the radiator filler neck, replenish
with EC. Repeat until the EC level does not drop any further.
Install the radiator cap and stop the engine.

Replenish EC to the "MAX" line on the reservoir tank and
leave as it is until the engine gets cool.


After the engine gets cool, start the engine and make sure
there is no water running noise heard from the heater core
while the engine runs at 3000 rpm.

Should water running noise be heard, repeat the same
procedure from the beginning.


Main Data and Specifications
General Specifications
Cooling system Engine Coolant forced circulation
Radiator Tube type corrugated (2 tube in row)
Heat radiation capacity 66.3 kcal/h
Heat radiation area 7.08 m2
Radiator front area 028 m2
Radiator dry (weight) 3.1 kg
Radiator cap valve opening pressure 93.3 – 122.7 kpa
Engine coolant capacity 2.0L
Engine coolant pump Centrifugal type
Thermostat Bypass type
Engine coolant total capacity 5.7lit

0B-14 MAINTENANCE AND LUBRICATION


GRADE LUBRICATION MAKE BRAND / TYPE
API ACEA
Automatic transmission
Power steering ISUZU GENUINE
EXXON / ESSO
MOBIL
CALTEX
SHELL
ELF
TOTAL
CASTROL
CASTROL BESCO ATF III, ATF II
ESSO ATF D (DEXRON

II-D)
MOBIL ATF (DEXRON
III)
ATF HD (DEXRON
II)
SHELL DONAX TA (DEXRON
II-D)
ELFMATIC G3 (DEXRON
III)
TOTAL FLUID IID (DEXRON
II-D)
TQ-D (DEXRON
II)
TQ DEXRON III (DEXRON
III)
















Grease fitting
(Multi purpose grease) ISUZU GENUINE
EXXON / ESSO
MOBIL
CALTEX / TEXACO
SHELL
TOTAL
CASTROL BESCO L-2 GREASE (No.2), L-3 GREASE (No.3)
RONEX MP (No.2)
MOBILGREASE HP 222 (No.2)
STARPLEX-2 (No.2)
RETINAX A (No.2)
MULTIS EP2, EP3 (No.2, No.3)
LM GREASE (No.2, No.3)












Propeller shaft sliding yoke
Universal joint
Multi purpose grease
containing molybdenum
disulfide ISUZU GENUINE
EXXON / ESSO
EXXON / ESSO
CALTEX
TOTAL ONE LUBER MO GREASE
BEACON Q2 (No.2)
MULTIPURPOSE GREASE (Moly) (No.2)
MOLYTEX GREASE EP2 (No.2)
TOTAL MULTIS MS2 (No.2)








Engine cooling system ISUZU GENUINE
TEXACO


CALTEX

GM GENUINE BESCO LLC SUPER TYPE E
HAVOLINE EXTENDED LIFE ANTIFREEZE
COOLANT
HAVOLIN XLC
EXTENDED LIFE COOLANT 6280
XLC
GOODWRENCH DEX-COOL
(TM) ANTIFREEZE
EXTENDED LIFE COOLANT















FLUID TYPE
Clutch and brake fluid reservoir Besco brake fluid (For light duty)
Hydraulic brake fluid SAE J1703
FMVSS 116 DOT.3 grade


DIESEL FUEL/APPLICABLE STANDARD
JIS (JAPANESE INDUSTRIAL STANDARD) Based on K2204 GAS OIL
DIN (DEUTSCHE INDUSTRIE NORMEN) Based on EN590 : 1997
SAE (SOCIETY OF AUTOMOTIVE ENGINEERS) Based on SAE J-313C
BS (BRITISH STANDARD) Based on BS EN590 : 1997


NOTE:
Use the applicable standard or equivalent for diesel fuels.