ISUZU TF SERIES 2004 Workshop Manual

Page 2131 of 4264

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-135
Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure Parts Related
ECM Pin
No. Related
Multiple
DTC
P1171 D Fuel Supply System Lean
During Power Enrichment
(Bank 1) B21/
B22/
-
44
P1172 D Fuel Supply System Lean
During Power Enrichment
(Bank 2) 1. No DTC relating to MAF sensor, IAT sensor,
ECT sensor, TPS, CMP sensor, CKP sensor,
VSS, injector control circuit, ignition control
circuit, O2 sensor circuit low voltage & high
voltage (bank 1 & 2) and O2 sensor circuit no
activity (bank 1 & 2).
2. Engine speed is between 1000rpm and
6000rpm.
3. Intake air temperature is below 70C.
4. Engine coolant temperature is between 30C
and 120C.
5. Engine load is between 150 and 255.
6. Throttle position output is more than 2.22V
and fluctuation is below 0.28V.
7. Except fuel cut operation.
8. O2 sensor output voltage below 250mV for 10
seconds. No fail-safe function.
O2 sensor output voltage is
more than 520mV for 5
seconds.
1. Sensor harness open or short to ground
circuit.
2. O2 sensor malfunction.
3. MAF sensor output is incorrect. 4. Air intake
line malfunction.
5. IAC valve malfunction.
6. Low fuel pressure.
7. Injector malfunction.
8. ECM malfunction.
B23/
B24 -
P0201 A Injector 1 Control Circuit
A36 - P0202 A Injector 2 Control Circuit
B3 - P0203 A Injector 3 Control Circuit
A35 - P0204 A Injector 4 Control Circuit
B4 - P0205 A Injector 5 Control Circuit
A34 -
31
P0206 A Injector 6 Control Circuit 1. No DTC relating to CMP sensor and CKP
sensor.
2. Under sequential injection.
3. Injection pulse is between 2.5ms and 7.5 ms.
4. Except fuel cut operation.
5. Engine speed is between 600rpm and
2000rpm.
6. 30 injection signals are not detected
consecutively. No fail-safe function. 30 injection signals are
detected consecutively. 1. Injector harness open circuit, short to ground
or short to voltage.
2. Injector malfunction.
3. ECM malfunction.
B5 -

Page 2132 of 4264

6E-136 3.5L ENGINE DRIVEABILITY AND EMISSIONS Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure Parts Related
ECM Pin
No. Related
Multiple
DTC
P0336 B Crankshaft Position Sensor
Circuit Range/Performance
(58X) 1. No DTC relating to CMP sensor.
2. Engine speed is below 2000rpm.
3. Extra or missing pulse is detected
consecutively. 1. CKP sensor harness open circuit, short to
ground or short to voltage.
2. Poor connector connection.
3. CKP sensor malfunction.
4. Pulse sensing gap incorrect.
5. Electrical interference.
6. Magnetic interference.
7. ECM malfunction. A23/
A24/
A25 P0122/
P0337
29
P0337 B Crankshaft Position Sensor
Circuit No Signal (58X) 1. No DTC relating to CKP sensor.
2. Engine speed is below 2000rpm.
3. Incorrect pulse is detected consecutively. No fail-safe function.
Correct pulse is detected
consecutively.

1. CKP sensor harness open circuit, short to
ground or short to voltage.
2. CMP sensor signal circuit short to ground
circuit.
3. TPS & CMP sensor power supply circuit short
to ground.
4. Poor connector connection.
5. CKP sensor malfunction.
6. Pulse sensing gap incorrect.
7. Electrical interference.
8. Magnetic interference.
9. ECM malfunction. A23/
A24/
A25 P0112/
P0336
P0341 B Camshaft Position Sensor
Circuit Range/Performance 1. Engine speed below 2000rpm.
2. No crankshaft position sensor DTC P0336 or
P0337.
3. Incorrect pulse is detected consecutively. 1. CMP sensor harness open circuit, short to
ground or short to voltage.
2. Poor connector connection.
3. CMP sensor malfunction.
4. Pulse sensing gap incorrect.
5. Electrical interference.
6. Magnetic interference.
7. ECM malfunction. B27/
B28/
B39 P0103/
P0113/
P0123/
P0342
41
P0342 B Camshaft Position Sensor
Circuit No Signal 1. No DTC relating to CKP sensor.
2. Engine speed is below 2000rpm.
3. No pulse is detected consecutively. Fuel cut is operated at high
engine speed.
Correct pulse is detected
consecutively.

1. CMP sensor harness open circuit, short to
ground or short to voltage.
2. Poor connector connection.
3. CMP sensor malfunction.
4. Pulse sensing gap incorrect.
5. Electrical interference.
6. Magnetic interference.
7. ECM malfunction. B27/
B28/
B39 P0103/
P0113/
P0123/
P0341
or
P0122

Page 2133 of 4264

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-137
Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure Parts Related
ECM Pin
No. Related
Multiple
DTC
P0351 A Ignition 1 Control Circuit
A32 - P0352 A Ignition 2 Control Circuit
B7 - P0353 A Ignition 3 Control Circuit
A31 - P0354 A Ignition 4 Control Circuit
B8 - P0355 A Ignition 5 Control Circuit
A30 -
42
P0356 A Ignition 6 Control Circuit 1. No DTC relating to CMP sensor and CKP
sensor.
2. Engine speed is between 250rpm and 850
rpm.
3. 10 ignition signals are not detected
consecutively. Fuel cut is operated more than
2000rpm. 10 ignition signals are detected
consecutively. 1. Ignition coil harness open circuit, short to
ground or short to voltage.
2. Ignition coil malfunction.
3. ECM malfunction.
B9 -

Page 2134 of 4264

6E-138 3.5L ENGINE DRIVEABILITY AND EMISSIONS Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure Parts Related
ECM Pin
No. Related
Multiple
DTC
P0404 B EGR Circuit
Range/Performance (Open
Valve) 1. Engine is stopping.
2. No DTC relating to ECT sensor, CKP sensor
and VSS.
3. Vehicle speed is below 4km/h.
4. Engine coolant temperature is more than
75C.
5. EGR solenoid valve on-duty ratio is more than
100%.
6. EGR valve output monitoring signal high. EGR valve output monitoring
signal low. 1. EGR solenoid harness short to voltage circuit.
2. EGR valve sticking.
3. ECM malfunction. A5 - P1404 B EGR Circuit
Range/Performance (Closed
Valve) 1. Engine is running.
2. Engine speed is below 4000rpm.
3. No DTC relating to CKP sensor.
4. EGR solenoid valve on-duty ratio is 0%.
5. EGR valve output monitoring signal low. 1. EGR operation is stopped.
2. EGR valve closed position
learning operation is
disabled.
3. EGR position feedback is
disabled.

EGR valve output monitoring
signal high. 1. EGR solenoid harness open circuit or short to
ground circuit.
2. EGR valve sticking.
3. ECM malfunction. A5 - P0405 B EGR Circuit Low
1. No DTC relating to EGR circuit
range/performance.
2. EGR solenoid valve on-duty ratio is more than
40%.
3. EGR position sensor output voltage is below
0.3V. EGR position sensor output
voltage is more than 0.3V. 1. EGR position sensor power supply circuit
open or short to ground circuit.
2. EGR position sensor signal circuit open or
short to ground circuit.
3. Poor connector connection.
4. EGR valve malfunction.
5. ECM malfunction. A9/
A24 - P0406 B EGR Circuit High
1. No DTC relating to EGR circuit
range/performance.
2. EGR solenoid valve on-duty ratio is below
40%.
3. EGR position sensor output voltage is more
than 4.6V. No fail-safe function.

EGR position sensor output
voltage is below 4.6V. 1. EGR position sensor power supply circuit
short to voltage circuit.
2. EGR position sensor signal circuit short to
voltage circuit.
3. EGR position sensor ground circuit open or
short to voltage circuit.
4. Poor connector connection.
5. EGR valve malfunction.
6. ECM malfunction. A9/
A22/
A24 P0118 P0444 A EVAP Purge Solenoid Valve
Circuit Low Voltage 1. No DTC relating to CKP sensor and system
voltage.
2. Engine speed is below 4000rpm.
3. Purge solenoid valve on-duty ratio is below
48%.
4. Purge solenoid valve output monitoring signal
low. Purge solenoid valve output
monitoring signal high. 1. Solenoid harness open circuit or short to
ground.
2. Solenoid malfunction.
3. ECM malfunction. B15 -
32
P0445 A EVAP Purge Solenoid Valve
Circuit High Voltage 1. No DTC relating to CKP sensor and system
voltage.
2. Engine speed is below 4000rpm.
3. Purge solenoid valve on-duty ratio is more
than 50%.
4. Purge solenoid valve output monitoring signal
high. No fail-safe function.

Purge solenoid valve output
monitoring signal low. 1. Solenoid harness short to voltage.
2. Solenoid malfunction.
3. ECM malfunction. B15 -

Page 2135 of 4264

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-139
Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure Parts Related
ECM Pin
No. Related
Multiple
DTC 24 P0500 B Vehicle Speed Sensor Circuit
Range/Performance 1. Engine speed is below 5000rpm.
2. Under fuel cut operation.
3. Vehicle speed sensor output is below 1km/h.
Above conditions are met for 4 seconds. The ECM use 10km/h
condition as substitute. Vehicle speed sensor output is
more than 2km/h. 1. Sensor harness open circuit, short to ground
circuit or short to voltage circuit.
2. Poor connector connection.
3. Electrical interference.
4. Magnetic interference.
5. VSS malfunction.
6. ECM malfunction. B32 -
P0562 D System Voltage Low Battery voltage is below 6V for more than 20
seconds. 1. Battery power feed harness open circuit or
short to ground circuit.
2. ECM ground harness open or poor
connection.
3. Poor connector connection.
4. Battery malfunction.
5. Charge system malfunction.
6. ECM malfunction. - -
66
P0563 A System Voltage High Battery voltage is above 16V for more than 20
seconds. No fail-safe function. Battery voltage is between 6V
and 16V.
1. Charge system malfunction.
2. Battery jump start cable misconnect.
3. ECM malfunction. - - 51 P0601 A Control Module Memory
Checksum ECM memory area error. Engine control disabled. Memory are is OK.
1. ECM malfunction. - -
P0602 - ECU Programming Error ECM memory area error. Engine control disabled. Memory are is OK.
1. ECM is not programmed. - -

Page 2136 of 4264

6E-140 3.5L ENGINE DRIVEABILITY AND EMISSIONS Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure Parts Related
ECM Pin
No. Related
Multiple
DTC
P1508 B Idle Air Control System
Low/Closed 1. No DTC relating to MAF sensor, IAT sensor,
ECT sensor, TPS, CMP sensor, CKP sensor,
VSS and system voltage.
2. Engine speed is between 675rpm and
6000rpm.
3. Engine coolant temperature is more than
75C.
4. Intake air temperature is between -10C and
80C.
5. Vehicle is stopping.
6. Small amount of intake air through the idle air
control valve. (Idle air control valve is sticking
at close position.) Above conditions are met
for 2 seconds. 1. IAC valve harness open circuit, short to
ground circuit or short to voltage circuit.
2. Poor connector connection.
3. IAC valve malfunction.
4. IAC valve is sticking at close position.
5. ECM malfunction. B13/
B14/
B16/
B17 -
22
P1509 B Idle Air Control System
High/Open 1. No DTC relating to MAF sensor, IAT sensor,
ECT sensor, TPS, CMP sensor, CKP sensor,
VSS and system voltage.
2. Engine speed is between 675rpm and
6000rpm.
3. Engine coolant temperature more than 75C.
4. Intake air temperature is between -10C and
80C.
5. Vehicle is stopping.
6. Large amount of intake air through the idle air
control valve. (Idle air control valve is sticking
at open position.) Above conditions are met
for 2 seconds. Fuel cut is operated at high idle
speed.
Correct amount of air intake
through the idle air control
valve. (Correct movement of
the idle air control valve.)

1. IAC valve harness open circuit, short to
ground circuit or short to voltage circuit.
2. Poor connector connection.
3. IAC valve malfunction.
4. IAC valve is sticking at open position.
5. ECM malfunction. B13/
B14/
B16/
B17 - 65 P1601 D CAN BUS Off CAN BUS off condition is detected consecutively.
CAN BUS on condition is
detected consecutively for 2
seconds. 1. ECM and TCM communication circuit open,
short to ground or short to voltage.
2. Electrical interference.
3. ECM malfunction.
4. TCM malfunction. A10/
A11 - 67 U2104 D CAN BUS Reset Counter
Overrun 1. No DTC CAN BUS Off.
2. CAN valid counter does not change for 2
seconds. Torque reduction control is
disable.
CAN valid counter changes
consecutively for 2 seconds. 1. ECM and TCM communication circuit open,
short to ground or short to voltage.
2. Electrical interference.
3. ECM malfunction.
4. TCM malfunction. A10/
A11 P1767/
U2104 (AT)

Page 2137 of 4264

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-141
Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure Parts Related
ECM Pin
No. Related
Multiple
DTC
P1626 - Immobilizer No Signal No response from immobilizer control unit.
1. ECM and immobilizer control unit
communication circuit open circuit, short to
ground circuit or short to voltage circuit.
2. Electrical interference.
3. Magnetic interference.
4. ECM malfunction.
5. Immobilizer control unit malfunction.
6. Transponder key malfunction. B18/
B32 B**** P1631 - Immobilizer Wrong Signal Received response is not correct.
1. ECM malfunction.
2. Immobilizer control unit malfunction.
3. Transponder key malfunction. - B**** P1648 - Wrong Security Code Entered Received incorrect security code.
1. ECM malfunction.
2. Immobilizer control unit malfunction.
3. Transponder key malfunction. - B****
67
P1649 - Immobilizer Function Not
Programmed Immobilizer function is not programmed in the
ECM. 1. Engine does not start.
2. Check engine lamp flash.
No recovery
ECM malfunction. - B****

Page 2138 of 4264

6E-142 3.5L ENGINE DRIVEABILITY AND EMISSIONS
MULTIPLE DTC SETS TROUBLESHOOTING AIDS
An open or short to voltage circuit in the sensor ground circuit between the ECM terminal A22 and splice will cause
one or more of following DTCs to be set:

  P0406 (Flash Code 32): EGR Circuit High

  P0118 (Flash Code 14): Engine Coolant Temperature Sensor High Input

A short to ground circuit in the sensor power supply circuit between the ECM terminal A24 and splice will cause one
or more of following DTCs to be set:

  P0122 (Flash Code 21): Throttle Position Sensor Low Input

  P0336 (Flash Code 29): Crankshaft Position Sensor Circuit Range/Performance (58X)

  P0337 (Flash Code 29): Crankshaft Position Sensor Circuit No Signal (58X)


RTW46EMF000201

Page 2139 of 4264

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-143
An open or short to voltage circuit in the sensor ground circuit between the ECM terminal B39 and splice will cause
one or more of following DTCs to be set:

  P0103 (Flash Code 61): Mass Air Flow Sensor Circuit High Input

  P0113 (Flash Code 23): Intake Air Temperature Sensor High Input

  P0123 (Flash Code 21): Throttle Position Sensor High Input

  P0341(Flash Code 41): Camshaft Position Sensor Circuit Range/Performance

  P0342 (Flash Code 41): Camshaft Position Sensor Circuit No Signal

An open circuit in the sensor power supply circuit between the ECM terminal B27 and splice will cause one or more of
following DTCs to be set:

  P0122 (Flash Code 21): Throttle Position Sensor Low Input

  P0342 (Flash Code 41): Camshaft Position Sensor Circuit No Signal

A short to ground circuit in the sensor power supply circuit between the ECM terminal B27 and splice will cause one
or more of following DTCs to be set:

  P0122 (Flash Code 21): Throttle Position Sensor Low Input

  P0336 (Flash Code 29): Crankshaft Position Sensor Circuit Range/Performance (58X)

  P0337 (Flash Code 29): Crankshaft Position Sensor Circuit No Signal (58X)

A short to ground circuit in the sensor signal circuit between the ECM terminal B28 and sensor will cause one of
following DTC to be set:

  P0337 (Flash Code 29): Crankshaft Position Sensor Circuit No Signal (58X)


RUW46EMF000101

Page 2140 of 4264

6E-144 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Too low fuel pressure (poor fuel) will cause one or more of following DTCs to be set.

  P0131 (Flash Code 15): O2 Sensor Circuit Low Voltage (Bank 1 Sensor 1)

  P0151 (Flash Code 15): O2 Sensor Circuit Low Voltage (Bank 2 Sensor 1)

  P0171 (Flash Code 44): O2 Sensor System Too Lean (Bank 1)

  P0174 (Flash Code 44): O2 Sensor System Too Lean (Bank 2)

  P1171 (Flash Code 44): Fuel Supply System Lean During Power Enrichment (Bank 1)

  P1172 (Flash Code 44): Fuel Supply System Lean During Power Enrichment (Bank 2)

Too high fuel pressure (excessive fuel) will cause one or more of following DTCs to be set.

  P0132 (Flash Code 15): O2 Sensor Circuit High Voltage (Bank1 Sensor 1)

  P0152 (Flash Code 15): O2 Sensor Circuit High Voltage (Bank 2 Sensor 1)

  P0172 (Flash Code 45): O2 Sensor System Too Rich (Bank 1)

  P0175 (Flash Code 45): O2 Sensor System Too Rich (Bank 2)




RTW36ELF000101

Page:   < prev 1-10 ... 2091-2100 2101-2110 2111-2120 2121-2130 2131-2140 2141-2150 2151-2160 2161-2170 2171-2180 ... 4270 next >