oil ISUZU TF SERIES 2004 Workshop Manual

MSG MODEL 7B-35


Important Operations
1. Intermediate Plate
2. Reverse Idler Shaft
1) Install the reverse idler shaft to the intermediate plate.
2) Tighten the reverse idler shaft bolt to the specified torque.
Idler Shaft Bolt Torque Nm(kgfm/lbft)
18.6 (1.9 / 13.7)



3) Set the mainshaft with gear assembly

1 and the counter
gear assembly

2 to the holding fixture
3.
Holding Fixture : 5-8840-2001-0 (J-29768)
4) Place the holding fixture (with the mainshaft and the
counter shaft) in a vise.
5) Mesh the 3rd-4th synchronizer to the 3rd gear.
Mesh the 1st-2nd synchronizer to the 1st gear.
6) Install the intermediate plate to the mainshaft and the
counter gear ball bearings.



6. Reverse Idler Gear
8. Counter Reverse Gear Lock Nut
1) Apply the engine oil to the idler shaft and the reverse gear
inside circumference.
2) Install the reverse gear to the idler shaft.
3) Install a new counter reverse gear lock nut.
Never reinstall the old lock nut.
4) Tighten the reverse gear lock nut to the specified torque.
Lock Nut Torque Nm (kgfm/lbft)
107.8 (11 / 79.6)



9. Thrust Washer
1) Apply the engine oil to both sides of the thrust washer.
2) Install the thrust washer to the mainshaft.
The thrust washer oil groove must be facing the reverse
gear side.

7B-36 MSG MODEL


13. Rev.-5th Synchronizer Assembly
1) Apply the engine oil to the clutch hub spline.
2) Install the synchronizer assembly to the mainshaft.
The sleeve heavy chamfer

1 and the insert short side
2
must be facing to the rear side of the transmission.


14. Mainshaft Lock Nut and Washer
1) Install a new lock nut and washer to the mainshaft.
Never reinstall the used lock nut and washer.
2) Use the lock nut wrench to tighten the lock nut to the
specified torque.
Lock Nut Wrench : 5-8840-0353-0 (J-36629)
Lock Nut Torque Nm(kgfm/lbft)
107.8 (11 / 79.6)



22. Counter Reverse Gear Nut and Washer
Tighten the counter gear lock nut to the specified torque.
Reverse Gear Nut Torque N
m(kgf
m/lb
ft)
107.8 (11 / 79.6)



18. Thrust Washer and Lock Ball
23. Thrust Washer Thrust Ring
24. Thrust Ring Snap ring
1) Install the thrust washer with lock ball together with the
thrust ring to the mainshaft.
2) Use a pair of snap ring pliers to install the snap ring.


3) Use a thickness gauge to measure the clearance between
the 5th gear and the thrust washer.
5th Gear and Thrust Washer Clearance mm(in)
Standard
0.1 - 0.3 (0.004 - 0.012)
If required, replace the existing thrust washer with a new
thrust washer to bring the clearance to specification.

7B-40 MSG MODEL
MAJOR COMPONENTS







RTW47BLF000401

Reassembly steps
1. Intermediate plate with gear assembly


2. Rear cover with oil seal


3. Transmission case


4. Bearing snap ring
5. Counter gear snap ring



6. Front cover with oil seal
7. Speedometer driven gear
8. Gear control box assembly
9. Speedpmeter sensor
10. Clutch shift fork
11. Clutch shift block and release bearing

MSG MODEL 7B-41

RTW47BSH000201
Important Operations
2. Rear Cover with Oil Seal
1)
Align the pins at the lower side of the rear cover with the
holes in the lower side of the intermediate plate.
2)
Apply recommended liquid gasket or its equivalent to the
rear cover fitting surfaces.
3) Install the rear cover to the intermediate plate.
4) Tighten the rear cover bolts to the specified torque.
Rear Cover Bolt Torque N
m(kgf
m/lb
ft)
37.2 (3.8 / 27.5)
Note:
Take care not to twist or puncture the oil seal during the
installation procedure.


RTW47BSH000301

3. Transmission Case
4. Bearing Snap Ring
1) Apply the engine oil to the transmission case top gear shaft
ball bearing fitting faces.
2)
Apply recommended liquid gasket or its equivalent to the
transmission case fitting surfaces.
3) Install the transmission case to the intermediate plate.
4) Pull the top gear shaft from the transmission case until the
ball bearing snap ring grove protrudes from the
transmission case front cover fitting faces.
5) Use a pair of snap ring pliers to install the snap ring to the
ball bearing.



6. Front Cover with Oil Seal
1) Clean and apply recommended liquid gasket or its
equivalent to the through bolt threads.
2) Install the new gasket and tighten the new cover bolt to the
specified torgue.
Front Cover Bolt Torgue N
m(kgf
m/lb.ft)
24.5 (2.5 / 18.1)









RTW47BSH000101
10. Shift Fork
Apply molybdenum disulfide type grease to the areas as
shown in the figure and install shift fork (Diesel engine).

7B-42 MSG MODEL

SPECIAL SERVICE TOOL
ITEM NO. ILLUSTRATION PART NO. PART NAME


MTL-42


9-8529-2201-0

Spring pin remover



MTL-1

5-8840-0013-0
(J-22888)

Gear remover


MTL-9

5-8840-2001-0
(J-29768)

Holding fixture


MTL-35

5-8840-0353-0
(J-36629)

Mainshaft nut wrench


MTL-3

5-8840-0015-0
(J-22912-01)

Bearing remover/installer


MTL-13

5-8840-0026-0
(J-26540)
Front cover oil seal
installer


MTL-14

5-8522-0050-0
(J-29769)
Rear cover oil seal
installer


MTL-21

5-8840-0178-0
(J-33851)

Mainshaft collar installer

MANUAL TRANSMISSION 7B1-1

SECTION 7B1
TRANSMISSION
MANUAL TRANSMISSION MUA
CONTENTS
PAGE
MUA (4





2)
Service Precaution .......................................................................................................... 7B1 – 3
General Description ........................................................................................................ 7B1 – 4
Rear Oil Seal (4




2) ........................................................................................................... 7B1 – 5
Transmission (4




2) ......................................................................................................... 7B1 – 7
Disassembled View ..................................................................................................... 7B1 – 7
Removal ....................................................................................................................... 7B1 – 8
Installation ................................................................................................................... 7B1 –12
Transmission Case .......................................................................................................... 7B1 –18
Major Component ........................................................................................................ 7B1 –18
Disassembly ................................................................................................................ 7B1 –19
Reassembly ................................................................................................................. 7B1 –20
Intermediate Plate with Gear Assembly, Detent, Shift Arm, Shift Rod,
and Interlock Pin ........................................................................................................... 7B1 –23
Disassembled View ..................................................................................................... 7B1 –23
Disassembly ................................................................................................................ 7B1 –24
Inspection and Repair ................................................................................................. 7B1 –25
Reassembly ................................................................................................................. 7B1 –26
Reverse Gear and 5th Gear ............................................................................................ 7B1 –27
Disassembled View ..................................................................................................... 7B1 –27
Disassembly ................................................................................................................ 7B1 –29
Inspection and Repair ................................................................................................. 7B1 –31
Reassembly ................................................................................................................. 7B1 –31
Top Gear Shaft, Main Gear Shaft, and Counter Gear Shaft ......................................... 7B1 –38
Disassembled View ..................................................................................................... 7B1 –38
Disassembly ................................................................................................................ 7B1 –40
Inspection and Repair ................................................................................................. 7B1 –42
Reassembly ................................................................................................................. 7B1 –45
Main Data and Specifications ......................................................................................... 7B1 –51

MANUAL TRANSMISSION 7B1-5

Rear Oil Seal (4





2)
Disassembled View
220R300030
Legend

(1) Rear Propeller Shaft (2) Rear Oil Seal

Removal
1. Raise and support vehicle with suitable jack stands.
2. Remove propeller shaft flange yoke bolts and nuts
at the differential side.
3. Remove center bearing from crossmenber.
4. Remove prepeller shaft from the transmission main
shaft spline.
Refre to the section “Rear Propeller Shaft”.
5. Use a screwdriver to pry the rear oil seal from the
rear cover.

Installation
1. Install a new oil seal (2) using the installer 5-8522-
0050-0.



220RS044
2. Insert the splined yoke into the transimission
mainshaft spline.
3. Install the propeller shaft flange yoke to the drive
pinion flange.

7B1-18 MANUAL TRANSMISSION

Transmission Case
Major Component
RTW37BLF0005
Legend

(1) Gear Control Box Assembly and Gasket (9) Front Cover (with Oil Seal)
(2) Speedometer Sensor and Driven Gear (10) Top Gear Bearing Snap Ring
(3) Rear Cover Assembly (11) Release Bearing : C24NE
(4) Intermediate Plate with Gear Assembly (12) Shift Fork : C24NE
(5) Transmission Case (13) Fulcrum Bridge : 6VE1
(6) Release Bearing (with Spring) : Diesel engine (14) Release Bearing : 6VE1
(7) Shift Fork : Diesel engine (15) Shift Fork : 6VE1
(8) Counter Front Bearing Snap Ring

7B1-20 MANUAL TRANSMISSION

13. Remove the rear cover assembly (3) from the
transmission case (5) and intermediate plate (4).
14. Remove intermediate plate with gear assembly (4)
from transmission case (5).
Reassembly
1. Apply recommended liquid gasket (LOCTITE 17430)
or its equivalent to the transmission case (5),
intermediate plate (4) and rear cover (3) fitting
surfaces.
2. Install the intermediate plate with gear assembly (4)
to the transmission case (5).
Pull out the top gear shaft until the ball bearing snap
ring groove protrudes from the transmission case
front cover fitting face.
Avoid subjecting the main shaft to sudden shock or
stress.
3. Install the rear cover with oil seal (3) on the
intermediate plate with gear (4) by performing the
following steps.


Cover the shaft splines with adhesive tape.
This will prevent damage to the oil seal lip. 4. Install a new gasket and gear control box assembly
(1).
Install the harness clips and brackets and then
tighten four new gear control box bolts to the
specified torque.
Torque: 20 N




m (2.0 kg




m/14 lb




ft)
261R300004
5. Install the O-ring (4) to the speedometer driven gear
bushing (3).
Install the driven gear to the speedometer driven
gear bushing (3).
6. Install the speedometer driven gear assembly (2) to
the transmission rear cover (3).
Install the plate (1) to the transmission rear cover
(3).
Torque: 15 N




m (1.5 kg




m/11 lb




ft)

MANUAL TRANSMISSION 7B1-21

7. Install the speedometer sensor (2).
Torque: 27 N




m (2.8 kg




m/20 lb




ft)
225R300001
8. Install top gear bearing snap ring (10) and counter
front bearing snap ring (8).


Use a pair of snap ring pliers to install the snap
rings to the mainshaft and countershaft.


The snap rings must be fully inserted into the
bearing snap ring groove.
9. Front cover with oil seal (9).
Front Cover Oil Seal Replacement


Remove the oil seal from the front cover.


Apply engine oil to a new oil seal outer
circumference.


Apply recommended grease to the oil seal lip.


Use the oil seal installer 5-8840-0026-0 to install
the oil seal to the front cover.

220R3000020
10. Install a new gasket and front cover (9) to the
transmission case.
NOTE: Take care not to damage the oil seal.
Notes When Tightening the Bolt:


After cleaning the bolt hole, dry it thoroughly with air.


After cleaning the screw face of a removed bolt or
new one, dry it thoroughly. Apply recommended
liquid gasket (LOCTITE 242) or its equivalent before
tightening it.
Tighten six front cover bolts to the specified torque.
Torque: 25 N





m (2.6 kg





m/19 lb





ft)
11. Apply molybdenum disulfide type grease to the
areas as shown in the figure and install shift fork (7).
(Diesel engine, C24NE)
F07L100026