oil ISUZU TF SERIES 2004 Workshop Manual

1-76 HEATER AND AIR CONDITIONING
INSPECTION AND REPAIR



840R300005-X

Resistor
As for air-conditioning model, fixed on left (RHD) / right (LHD)
side of the evaporator unit.
As for heater only model, fixed on left (RHD) / right (LHD) side
of the duct placed between blower unit and heater unit.
Replace the resistor with a new on if the coil is found to be
open or if the resistance value deviates from the specified
range.




Terminal Resistance
3 – 2 1.99


3 – 4 0.9


3 – 1 0.17




Blower motor
Check blower motor for smooth rotation.
Connect the battery positive terminal to the No.1 terminal of the
blower motor and negative to the No.2.
Be sure to check to see if the blower motor operates correctly.

HEATER AND AIR CONDITIONING 1-83

AIR CONDITIONING CYCLE TROUBLESHOOTING

TROUBLE POSSIBLE CAUSE CORRECTION
No cooling or
insufficient
cooling
1. Magnetic clutch does not run


Refer to “MAGNETIC CLUTCH”
troubleshooting in this section
2. Compressor is not rotating properly

Drive belt loosened or broken

Adjust the drive belt to the specified
tension or replace the drive belt


Magnetic clutch face is not clean and
slips
Clean the magnetic clutch face or replace




Incorrect clearance between magnetic
drive plate and pulley

Adjust the clearance (Refer to
“COMPRESSOR OVERHAUL”



Compressor oil leaks from shaft seal or
shell

Replace the compressor




Compressor seized

Replace the compressor

3. Insufficient or excessive charge of
refrigerant

Discharge and recover refrigerant.
Recharge to specified amount.
4. Leaks in the refrigerant system




Check refrigerant system for leaks and
repair as necessary
Discharge and recover refrigerant.
Recharge to specified amount.
5. Condenser clogged or insufficient radiation


Clean the condenser or replace as
necessary


Check radiator or condenser fan function

6. Temperature control link unit of the heater
unit defective

Repair the link unit

7. Unsteady operation due to foreign
substance in expansion valve

Replace the expansion valve

8. Poor operation of electronic thermostat


Check electronic thermostat and replace
as necessary
Insufficient
velocity
of cooling air

1. Evaporator clogged or frosted


Check evaporator core and replace or
clean the core
2. Air leaking from cooling unit or air duct

Check evaporator and duct connection,
then repair as necessary

3. Blower motor does not rotate prop-erly


Refer to “FAN CONTROL KNOB (FAN
SWITCH)” troubleshooting in this section

* For the execution of the charging and discharging operation in the table above, refer to the “RECOVERY,
RECYCLING, EVACUATING AND CHARGING” in this section.

7B-2 MSG MODEL
MAIN DATA AND SPECIFICATIONS

Transmission type Fully synchronized 5-forward gears with a constant
mesh type reverse gear.

Transmission Control Direct control with the gear shift lever on the floor.

Gear ratio MSG5K
1st : 4.122
2nd : 2.493
3rd : 1.504
4th : 1.000
5th : 0.855
Rev : 3.720

Oil capacity lit. (US gal.) 1.55(0.41)

Weight ; approx. kg(lbs) 33.3(73.8)

MSG MODEL 7B-7
REMOVAL AND INSTALLATION

Read this Section carefully before performing any removal and installation procedure. This Section gives you
important points as well as the order of operation. Be sure that you understand everything in this Section before
you begin.





Important Operations - Removal
Battery Cable
Disconnect the negative (-) cable from the battery terminal.

Engine Hood
Apply setting marks to the engine hood and the engine hood
hinges before removing the engine hood.



Gear Shift Lever
1. Place the gear shift lever in the neutral position.
2. Remove the gear shift lever knob.
3. Remove the front console assembly.
4. Remove the gear shift lever grommet and dust cover.
5. Remove the gear shift lever cover bolts.
6. Remove the gear shift lever.
Note:
Cover the shift lever hole to prevent the entry of foreign
material into the transmission.



Lifting the Vehicle
1. Jack up the vehicle.
2. Place chassis stands at the front and the rear of the
vehicle.




Transmission Oil Draining
1. Remove the transmission oil drain plug.
2. Replace the drain plug after draining the oil.

7B-14 MSG MODEL



Exhaust Pipe
1. Install the exhaust pipe to the exhaust manifold and the
2nd exhaust pipe.
2. Install the exhaust pipe bracket to the transmission case.

Gear Shift Lever
1. Replenish the transmission case with the specified engine
oil.
Transmission Case Oil lit(US gal.)
1.55 (0.41)

2. Install the gear shift lever to the gear control box.
3. Tighten the gear shift lever cover bolts to the specified
torque.
Shift Lever Cover Bolt Torque N

m(kgf

m/lb

ft)
19.6 (2.0 / 14.5)
4. Install the dust cover and the grommet.
5. Install the front console assembly.
6. Install the gear shift lever knob.



Lowering the Vehicle
1. Place a jack beneath the vehicle.
2. Raise the jack to remove the chassis stands.
3. Lower the vehicle to the ground.



Engine Hood
Align the setting marks(applied at removal)on the engine hood
and the engine hood hinges to install the engine hood.



Battery Cable
Connect the negative (-) cable to the battery terminal.

MSG MODEL 7B-15
DISASSEMBLY
MAJOR COMPONENTS




RTW47BLF000301

Disassembly Steps
1. Clutch shift block and release bearing
2. Clutch shift fork
3. Speedometer sensor
4. Speedometer driven gear assembly
5. Gear control box assembly


6. Front cover with oil seal



7. Counter gear snap ring


8. Bearing snap ring
9. Rear cover with oil seal
10. Transmission case
11. Intermediate plate with gear assembly

7B-16 MSG MODEL



Important Operations
6. Front Cover with Oil Seal
Remove the front cover with oil seal from the transmission
case.



7. Counter Gear Snap Ring
8. Bearing Snap Ring
Use pair of snap ring pliers to remove the snap ring.

7B-28 MSG MODEL


BALL BEARING PLAY
Use a dial indicator to measure the ball bearing play.
Ball Bearing Play mm(in)
Limit
0.2 (0.0079)



FRONT COVER OIL SEAL
Oil Seal Replacement
Oil Seal Removal
Use a screwdriver to pry the oil seal from the front cover.





Oil Seal Installation
1. Use the oil seal installer to install the oil seal to the front
cover.
Oil Seal Installer : 5-8840-0026-0 (J-26540)
2. Apply engine oil to the oil seal lip.



REAR COVER OIL SEAL
Oil Seal Replacement
Oil Seal Removal
Use a screwdriver to pry the oil seal from the rear cover.





Oil Seal Installation
1. Use the oil seal installer to install the oil seal to the rear
cover.
Oil Seal Installer : 5-8522-0050-0 (J-29769)
2. Apply engine oil to the oil seal lip.

MSG MODEL 7B-31



Important Operations
2. Needle Bearing
3. 2nd Gear
1) Apply the engine oil to the 2nd needle bearing and the 2nd
gear.
2) Install the needle bearing and the 2nd gear to the
mainshaft.
The dog teeth of the 2nd gear must be facing the rear side
of the transmission.


5. 1st-2nd Synchronizer Assembly
1) Apply the engine oil to the clutch hub spline.
2) Install the synchronizer assembly to the mainshaft.
The outside sleeve heavy chamfering must be facing the
rear of the transmission.
1 Chamfer Angle = 30


2 Chamfer Angle = 45





7. Needle Bearing Collar
Use a bench press and the collar installer to install the needle
bearing collar.
Collar Installer : 5-8840-0178-0 (J-33851)



8. Needle Bearing
9. 1st Gear
1) Apply the engine oil to the 1st needle bearing and the 1st
gear.
2) Install the needle bearing and the gear to the mainshaft.
The dog teeth of the 1st gear must be facing the front side
of the transmission.


10. 1st Gear Thrust Washer
Install the thrust washer to the mainshaft.
The thrust washer oil groove must be facing the 1st gear side.

7B-32 MSG MODEL



11. Mainshaft Ball Bearing
1) Apply the engine oil to the ball bearing inside
circumference.
2) Use a bench press and the bearing installer to install the
bearing.
The bearing snap ring groove must be facing the front o
f
the transmission.
Bearing Installer : 5-8840-0015-0 (J-22912-01)




12. Needle Bearing
13. 3rd Gear
1) Apply the engine oil to the 3rd needle bearing and the 3rd
gear.
2) Install the needle bearing and the gear to the mainshaft.
The dog teeth of the 3rd gear must, be facing the front side
of the transmission.






15. 3rd-4th Synchronizer Assembly
1)
Apply the recommended lubricating oil to the clutch hub
spline.
2) Install the synchronizer assembly to the mainshaft.
The sleeve light chamfering

1 and the clutch hub heavy
boss

2 must be facing the rear of the transmission.



16. Mainshaft Snap Ring
1) Select the snap ring which will provide the minimum
clearance between the mainshaft and the snap ring.
There are four snap ring sizes available.
The snap rings are numbered to indicate their thickness.
Mainshaft and Snap Ring Clearance mm(in)
Standard
0 - 0.05 (0.002)


Snap Ring Availability mm(in)Thickness Identification Number
1.50 (0.059) 1
1.55 (0.061) 2
1.60 (0.063) 3
1.65 (0.065) 4
2) Use a pair of snap ring pliers to install the snap ring to the
mainshaft.