ISUZU TF SERIES 2004 Workshop Manual
Page 791 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-133
4. Keep the vehicle 2 1m apart from the screen 1.
5. Draw a horizontal line through point
A and Bon the screen
1.
6. Turn the headlight low beam on.
7. Adjust the CUTLINE 11.6 mm below the horizontal line
H.
8. Adjust the BENDING POINT to the vertical line
V.
NOTE:
Always adjust vertical adjustment first.
Page 792 of 4264
8A-134 ELECTRICAL-BODY AND CHASSIS
INSPECTION AND REPAIR
Switch side Harness side
B-60 B-60
LIGHTING SWITCH
Lighting Switch Connections
Terminal
SW No.
position 3 2 1
OFF
Tail
Headlight
Switch side Harness side
B-60 B-60
HEADLIGHT BEAM SWITCH
Headlight Beam and Passing Switch
Connections
Terminal NO.
SW position 1 4
HI
At “Dimmer” position
LO
At “Passing” Position
Page 793 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-135
LIGHTING RELAY, TAIL RELAY
Check continuity between the relay terminals.
2 - 1............................. No continuity
(When battery voltage is applied between 3 and 4)
2 - 1............................. Continuity
GLOVE BOX ILLUMINATION
Removal
1. Remove the bulb cover 1.
2. Remove the bulb
2.
Installation
To install, follow the removal steps in the reverse order.
POWER/3rd START SW
Removal
Refer to the “Front consol” Section 10 of this manual.
1. Disconnect the battery ground cable.
2. Remove the power/3rd start switch.
3. Remove the bulb.
Installation
To install, follow the removal steps in the reverse order.
A/T LEVER LIGHT BULB
Removal
Refer to the “Front consol” Section 10 of this manual.
1. Remove the A/T lever cover.
2. Remove the light bulb
1.
Installation
To install, follow the removal steps in the reverse order.
Page 794 of 4264
8A-136 ELECTRICAL-BODY AND CHASSIS
FRONT FOG LIGHT
PARTS LOCATION (RHD)
RTW48AXF015001 & RTW48AXF015101
Page 795 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-137
PARTS LOCATION (LHD)
RTW48AXF015201 & RTW48AXF015301
Page 796 of 4264
8A-138 ELECTRICAL-BODY AND CHASSIS
CIRCUIT DIAGRAM (RHD)
RTW48AXF007801
Page 797 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-139
CIRCUIT DIAGRAM (RHD) EUROPE
RTW48AXF008001
Page 798 of 4264
8A-140 ELECTRICAL-BODY AND CHASSIS
CIRCUIT DIAGRAM (LHD)
RTW48AXF007901
Page 799 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-141
CIRCUIT DIAGRAM (LHD) EUROPE
RTW48AXF014901
Page 800 of 4264
8A-142 ELECTRICAL-BODY AND CHASSIS
FRONT FOG LIGHT
Removal
1. Remove the radiator grille.
2. Remove the front bumper
3. Disconnect the fog light connector.
4. Remove the fog light.
5. Remove the bulb from the socket.
Remove the socket by turning it counterclockwise.
Installation
Follow the removal procedure in the reverse order to install the
fog light.
Pay close attention to the important points mentioned in the
following paragraphs.
Bulb
Be absolutely sure that the fog light bulb is correctly installed.
This will prevent a poor contact and open circuit.
FRONT FOG LIGHT ADJUSTMENT
Vertical Adjustment
Turn the adjusting screw (1) with a screwdriver to adjust the
aim of the fog light vertically.
RTU4Z0SH000601
FRONT FOG & REAR FOG SWITCH